Sender Channel Connection problem

Hi ,
I am getting the following error in the Adapter monitoring under RWB.
<b> Error: ConnectException: Connection refused: connect
- 2007-05-04 09:41:42 CEST: Processing started</b>
This happen all out of a sudden. I changed nothing in the Sender CC.
I also added a "\" towards the end of the directory access path in the sender CC.
What do you think is the problem ??

HI,
Are you using FTP as sender?
This problem is either caused by incorrect firewall / packet filter settings or an incorrect configuration of the FTP server. Also make sure that you have correctly specified the host name / IP address and port of the FTP server.
Changing the connection type from 'active' to 'passive' (or vice versa) might additionally help to work around the incorrect firewall configuration
see SAP Note No:821267
Regards
Chilla

Similar Messages

JMS Sender Channel - reconnect problem

Hi,
I've got a sender channel which picks up messages from MQSeries and sends them to XI.
If I set the MQSeries Queue to "Get Inhibited" to simulate a network problem, the channel goes down with a standard error message
"Sender channel. Details: MQJMS2002: failed to get message from MQ queue Code: MQJMS2002".
A receiver channel that looses connection gives me the same error.
So I've got 2 problems :
- how can I get the MQSerier error message (2016, MQRC_GET_INHIBITED )
- how come the adapter doesn't reconnect after correction of the problem ?
Tx in advance
Tom

Hi Tom,
I get the same error , i tryed looking at the IBM and eocnte at the following links, but not able to solve the problem yet.
<a href="http://www-1.ibm.com/support/docview.wss?rs=180&uid=swg1PK02976">http://www-1.ibm.com/support/docview.wss?rs=180&uid=swg1PK02976</a>

Sender Channel getting problem "RFCSenderR3 "

Hello friends,
In my XI QA env...there is one service "RFCSenderR3" which is not showing any messages like in message monitoring ,but if i check in Communication channel CC monitoring for that service it shows as following error :
Error*
Sender channel 'RFCSenderR3' for party ",service'RQ1'
ERROR can not instantiate RfcPoolException:error initializing
RfcServerPool:com.sap.aii.af.rfc.core.repository.RfcRepositoryException:can not connect to destination system due to :com.sap.mw.jco.JCO$Exception:(103) RFC_ERROR_LOGON_FAILURE:Mandante 101
Here RQ1 is the R3 reciever system.
And i have checked rfc connection from R3 end which shows it is fine..
Can any one suggest me and help me ,exactly what should i need to be checked to solve this problem .
Thank you

Hi,
>-----> RFC_ERROR_LOGON_FAILURE
Could you pls. check for user id and password whether you have given R3.
Mean time try to stop and restart the service.

MacBookPro, V.10.5; Firefox 3.6.10; cannot send email "connection problem" - switched to "classic mail" sent no problem ... ?

MacBookPro, OS x (10.6.5); Firefox 3.6.10; problem recently came up - no changes to system ... "cannot send mail due to connection problem" - When problem with Firefox came up, I could send mail with Thunderbird ... today (third day w/problem) I switched to Firefox "classic mail" and sent mail with no problem

a day or two later, this problem went away ... -?-

Connection problem in SOAP Sender Channel

Dear All,
I have created two SOAP Sender channel with the following specification:
Transport Protocol - HTTP
Message Protocol - SOAP 1.1
HTTP Security Level - HTTP
But while sending a message from a Java client, I am getting the following error :
The HTTP request is unauthorized with client authentication scheme 'Anonymous'. The authentication header received from the server was 'Basic realm="XISOAPApps"'.
Please suggest if you find any way out.
Thanks and Regards,
Rana Brata De

Hi Rana
Looks like you have used authentication scheme as 'anonymous'. But you have chosen the option 'HTTP' in soap adapter.
So you have to pass the user id and password during the call.
Sample Code:
ICalcCTCWebService calcCTCWebService = calcCTCWebServiceImplServiceLocator.getCalcCTCWebServiceImplPort();
Stub stub = (Stub)calcCTCWebService;
stub._setProperty(Stub.USERNAME_PROPERTY, "abc");
stub._setProperty(Stub.PASSWORD_PROPERTY, "xyz");
You can also test the WSDL from SOAP UI and provide user name and password in the header section in SOAP UI and see if the message goes to PI or not.
You can also try the below option in the sender soap adapter and see if it works or not.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hello Sue,
I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
Michael

JDBC Sender Channel problem. Pls help

Hi,
In JDBC Sender Channel in Connectiion String I am giving value
jdbc:oracle:thin:@cscappnoi022.asiapac.globalcsc.net:1527:IS1
where cscappnoi022.asiapac.globalcsc.net---is where Oracle server is installed
1527 --- is my Port
IS1 is my system SID --- Pls let me what value should come here and how to find.
I am getting error
"Error during database connection to the database URL 'jdbc:oracle:thin:@cscappnoi022.asiapac.globalcsc.net:1527:IS1' using the JDBC driver 'oracle.jdbc.driver.OracleDriver': 'com.sap.aii.adapter.jdbc.sql.DriverManagerException: Cannot establish connection to URL 'jdbc:oracle:thin:@cscappnoi022.asiapac.globalcsc.net:1527:IS1': SQLException: Io exception: The Network Adapter could not establish the connection'"
Regards

hi,
Your connection should be :
jdbc:oracle:thin:hutting/[email protected]:1521:pnt
jdbc driver should be:
oracle.jdbc.driver.OracleDriver
Regards
joel.
I only hope that your other jdbc scenarios are working fine , this is just to rule out the possibility of driver related errors.

I am Facing problem with "Send to connection" in SharePoint Server 2010.

Hi all,
I am working on SharePoint Server 2010
I have a site collection and sub sites in it.
I want to move the document form one site library to another site library.
Since it can be done by configuring, Send to connection in Central Admin.
I activated Content Organizer rules in both the sites.
I added new connection for one site and append the url
/_vti_bin/officialfile.asmx
I tested the url on clicking
Click here to test link it gives me message that
"URl is a Valid routing Destination".
and finally I added the connection
After configuring this I open the other site and uploaded a document in it and after uploading the document I selected send to
option and clicked on my connection what I created in central admin.
But it gives me error: The site could not be found or accessed
Please help me for this...
Thanks in advance..
Faheem Ahamed

Hi,
In my case, I'm routing an InfoPath form (After having approved) to an archived Forms Library within the same sub-site.
I created Send To connection, setup Content Organizer rules, setup Record Retention policy on the source Forms Library, but even after running both the Timer jobs (Information management policy and Expiration policy), the document didn't get moved to the
archived library.
I checked under Compliance details of the form that the Scheduled occurrence date shows 'Completed' i.e. the Information management policy timer job did its task, but the other Timer job didn't move this form.
Then I tried sending this form manually using Send To. In that case, although the form got moved to the archived library, but I see 'Unexpected error' on the screen.
The ULS shows following entries:
<nativehr>0x80070057</nativehr><nativestack></nativestack>Invalid data has been used to update the list item. The field you are trying to update may be read only.Possible mismatch between the reported error with code = 0x8107210c
and message: "Invalid data has been used to update the list item. The field you are trying to update may be read only." and the returned error with code 0x80070057.
OfficialFile: File
http://server/sites/site/SourceFormsLibrary/InfoPathForm.xml was not saved at router location TargetLibrary. Exception <nativehr>0x80070057</nativehr><nativestack></nativestack>Invalid data has been used to update the list item.
The field you are trying to update may be read only. thrown at: at Microsoft.SharePoint.Library.SPRequestInternalClass.AddOrUpdateItem(String bstrUrl, String bstrListName, Boolean bAdd, Boolean bSystemUpdate, Boolean bPreserveItemVersion,
Boolean bPreserveItemUIVersion, Boolean bUpdateNoVersion, Int32& plID, String& pbstrGuid, Guid pbstrNewDocId, Boolean bHasNewDocId, String bstrVersion, Object& pvarAttachmentNames, Object& pvarAttachmentContents, Object& pvarProperties,
Boolean bCheckOut...
Critical --- The
http://server/sites/site/_vti_bin/OfficialFile.asmx site is not properly configured for this request.
Can somebody tell how manual Send To is working within the same site collection.
Any help will be appreciated!
Thanks!
Ashish

Need help about setting up a JMS sender channel

I just started to play with PI for a few weeks and I'm trying to setup a simple JMS sender channel to read stuff from a WebSphere MQ.
I've someone installed JMS adaptor for me, but we never know it is correctly installed or not. First question is "Is there any way we can verify JMS adapter is correctly installed or not?"
In the Design: integration builder, I've a very defined a very simple data type(src_dt) which is a string and a message type(src_mt) which uses resp_dt. Finally I created a message interface (test_mia_out) that contains src_mt. At this point of time, I don't need message mapping so I didn't configurate this section.
Then I went to Configuration: Integration builder and created a new communcation channel with the following setting:
Parameter section:
Adapter Type: JMS
Transport Protocol: WebSphereMQ (Non-JMS) <- if i don't use this option, i can't enter MQ connection detail in the Source section.
Message Protocol: JMS 1.x
Adapter Engine: Integration Server
Source section:
QueueConnectionFactory Java Class: com.ibm.mq.jms.MQQueueConnectionFactory
Queue Java Class: com.ibm.mq.jms.MQQueue
...MQ connection detail...(IP, Port, Queue Manager, Channel and Queue Name )
Transport Protocol: TCP/IP <- this is consists to server side setting
JMS-Compliant: JMS-Compliant
Since I only want a very simple working sample, again I didn't change the content in receiver determination, interface determaintion and sender agreement.
Now when I active this change and I saw the following error in the channel monitor:
Short Log - Channel has internal error
Admin Info - Exception: Channel with Status Unknown or Not Registered
I did stop and start the service, refresh CPA cache and even restart the entire PI server, I always see this message and cannot find any more detail description about what is causing this problem.
My PI Server version is 7.0 and MQ version is 5.3
There's very limited resource about how to setup to read MQ message in PI and I'm stuck now. Therefore, I need a help from some experienced people to tell me if I have did something wrong or missed some steps?
And if possible, could people mind to post a step by step go through how you setup it up?
Edited by: Robert Fu on Jan 10, 2008 6:51 AM

Before you use the JMS, you need to deploy some drivers related to specific MQseries, Kindly ensure that proper driver are deployed....
If you use MQSeries 53x.xxx, you must enter the following JAR files in aii_af_jmsproviderlib.sda.
com.ibm.mq.jar, com.ibm.mqbind.jar, com.ibm.mqjms.jar, connector.jar (use the JAR file from the J2EE client directory)
check this link it will give you more inofmration
http://help.sap.com/saphelp_nw04/helpdata/en/cd/d85a9d6fab7d4dbb7ae421f710626c/content.htm
check this to get the condifuration the JMS
How to use conversion modules in JMS - https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f02d12a7-0201-0010-5780-8bfc7d12f891
Ref How To Use the Content Conversion Module in JMS Adapter - https://websmp106.sap-ag.de/~form/sapnet?_SHORTKEY=01100035870000582377&

SAP XI File Adaptor (FTP mode) Sender Channel FTP commands

I have a service set up to communicate via ftp to an external partner. Their FTP server is secured to a point that I am unable to connect with normal settings. They claim that the FTP server follows the RFC 959 standard and therefore we should be able to connect and extract a file from their server. Not happening!
The question:
What are the exact ftp commands issued by a Sender channel configuration to an external FTP server? I have all the usual setting: user/pass/path/server/file (with wild card).
I can not find a definitive listing of commands issued by the file adapter in ftp mode to the remote ftp server. Not just a listing but an actual flow of commands issued would be useful.
Would appreciate some help/direction.
Thanks,
Mike

Hi Michael,
Please look at the FTP Server parameters...
1) if you have given the uncheck the anonymous login they can connect with out giving the username and password to connect to the FTP server...please check this paramerter and also make sure that if are mainting the username and password it should be the same they are using to access the FTP server.
2) Please check the port and ip address
For more information i would suggest you to look at the following link:
http://help.sap.com/saphelp_nw2004s/helpdata/en/0b/9a50465ccf84479e39a6d50c90fb3f/frameset.htm
Could you please reply us what would be exact problem u r facing?
Thanks and Regards,
Chandu.

EOIO JMS Sender Channel in Error

Hi All,
We have a error on JMS sender channels in Pre-Production environment.
Let me explain you the problem.
On Dev and QA there is no cluster environment. On Pre-production we have 3 clusters. We tested this Sender JMS channel on Dev and QA without giving a Cluster ID and it worked.
Now on Pre prod, we had not mentioned the cluster ID and when messages were picked from the Queue, the channel went into a error mode stating the " Channel is locked due to EOIO".
Then when we added the cluster ID to the channel, in RWB the channel goes into inactive mode. The status is " The EOIO channel has been made inactive on Node 206485150"
The node mentioned in channel is 251902150. This means that the other node has been made inactive. That sounds logical as it is not supposed to process the message.
But the node which is mentioned in the channel has also gone into error mode.
" Error creating JMS connection. failed to create MQManager for ' Hostname:Channel name'". An MQException occured: Completion code 2, Reason 2009
MQJE016: MQ queue managerclosed channel immediatly during connect. Closure reason= 2009, and erro code as MQJMS2005
After this all other sender JMS channels have gone into the same error mode on this node.
We have stopped the JMS service and started it. We also restarted the XI server but no change was encountered.
Please let us know whether JMS sender with EOIO works with cluster ID as I'm not able to find any document which says that JMS with EOIO works succesfully.
Please also let us know how to overcome the error on this node.
Thank you.
Regards,
Sarvesh Desai

Check if there is any unprocessed message stuck in the queue:
/people/stefan.grube/blog/2006/04/27/how-to-deal-with-stuck-eoio-messages-in-the-xi-30-adapter-framework

JDBC and FTP sender channels stop polling

Hi,
We have a great volume of sender JDBC and FTP sender channels.
For this reason there is nothing unusual to have temporary error connections.
Several months ago, with an XI 3.0 system, sender channels recover its functionality automatically when temporary error connection is solved.
But now, he have migrate to a PI 7.1 sytem, and in the same scenario and configuration, sender channel stop polling after a temporary error . In cc monitor this channels remains in green status and there were no signs of stopped interfaces.
Timeouts are correctly defined and there is no difference between channel configuration in our Xi and PI system.
How to solve this problem?
Thanks, in advance.
Carme.

Thanks for your fast response, Stefan.
After writing this post, i ask the same question to our basis team and we are in the latest sp.
¿do you know if there is any note or can you provide me some additional information?
I'm not able to find any note about this issue...
Regards,
Carme.

Sender Channel not working(RFCSenderR3)

Hello All,
In my XI 3.0 QA env...there is one service "RFCSenderR3" which is not showing any messages in message monitoring ,but if i check in Communication channel monitoring for that service it shows as :
Sender channel 'RFCSenderR3' for party ",service'RQ1'
ERROR can not instantiate RfcPoolException:error initializing
RfcServerPool:com.sap.aii.af.rfc.core.repository.RfcRepositoryException:can not connect to destination system due to :com.sap.mw.jco.JCO$Exception:(103) RFC_ERROR_LOGON_FAILURE:Mandante 101
Here RQ1 is the R3 reciever system.
And i have checked rfc connection from R3 end which shows it is fine..
Can any one suggest me ,exactly wat need to be checked to solve this problem .And I am not sure what to check from R3end also....
can any one guide to me ..
Best Regards
raki

Hello All,
Thanks for helping yaar,the problem got resolved .
After verifying the user Id & password , I restarted that particular channel from Communication channel monitoring.Then it got worked with successful execution.
Thanks one and all for helping me out.
Best Regards
Rakesh

JMS Sender Channel not Polling

Hi Guys,
Scenario: BEA Weblogic -
> JMS Queue -
> Sender Channel JMS -
> SAP XI -
> SAP R3
We had initially setup this scenario using MessageSelector because the provider JMS Queue had mutiple message types on it. As Murphy's law would have it, the MessageSelector stopped polling the day before go-live. Basically, if we pointed one JMS SC to the provider JMS Queue using MessageSelector it worked fine, if we pointed multiple JMS SC's no messages were being picked up from the queue. We still haven't identified why the MessageSelector functionality stopped working but as a quick work around to MessageSelector before go-live we used blog:
[/people/robert.warde3/blog/2009/03/18/pi-basics-generic-message-interface|/people/robert.warde3/blog/2009/03/18/pi-basics-generic-message-interface]
Now we have a situation where, BEA Weblogic manages the provider JMS Queue & they perform a health check 4 times a day & if they encounter a problem they bounce the server & JMS Queue service. XI and the SC seem to re-connect fine most of the time when Weblogic & JMS Queue is back up but there are times when I see a green light in RWB for the SC but it's not polling for messages on the JMS Queue. We use Hermes JMS to monitor messages on the Queue to check if there are in fact messages to be picked up & the messages are queued.
What I'm looking for is a best practice guide for how to manage this. I don't want to keep toggling between Hermes JMS & RWB to verify if the SC is in fact polling messages altho' it shows as green in RWB. Please advise. Thanks.
Regards, Trevor

Thanks Kai & Joel.
Joel, I'm not really looking to add another layer with the JMS Connector Service. For me it's just adds another possible point of failure. At the moment the message passes thru 5 systems including SAP R3 & end system & then the response comes back the same route.
Going out from SAP, the Receiver channel to the JMS queue seems to work fine. With the responses coming back, the Sender Channel seems to re-connect ok (I'm assuming) otherwise it wouldn't be green in RWB but doesn't pick up any messages. It's also an intermittant phenomenon. Manually stopping & re-starting the Sender Comm Channel fixes the problem but we won't know if there's a problem until we check if messages are being picked up from the queue.
Kai's notes led me to some things I could possibly look at like additional parameter in JMS channel config, CONNECTION_TEST_POLL (note 948016). I'm still not sure how we can make this work for us because we essentially need to bounce the JMS channel so it starts polling again in the event of a JMS Queue Provider bounce but I need to first establish that the JMS Queue was bounced.
Note 1088675 will also be irrelevant cos the channel looks like it re-connects, just doesn't poll.
Trevor

JMS sender channel error

hi,
i am using pi 731 single stack.
i have a jms sender channel. The jms sender channel is connecting to Webshere MQ version 6.0.2.10.
the error is -
Error creating JMS connection : The JMS provider gave the error message as MQJMS2005:failed to create
MQQueueManager for x.y.com:QMgr1 MQJE001 completion code 2,Reason 2059,and the error code as MQJMS2005
What could be the issue. The JMS drivers are successfully installed.

Hi,
As Indrajit said seems to be a JMS configuration problem. Check this thread in stackoverflow with the same error: java - Always receive MQJE001: Completion Code &#39;2&#39;, Reason &#39;2059&#39;. ERROR - Stack Overflo…
Regards.

Sender Channel Connection problem

Similar Messages

Maybe you are looking for