Sendmail & SAP SMTP have port conflict !
Hi SAP Gurus,
I am in process of configuring inbound & outbound Email in my ERP system. Now the problem is we have sendmail running on Port 25 on the host where SAP installed.
Because of this i can not start my SAP SMTP service on port 25. If i start on 25000 outgoing working fine but incoming not working at all.
Can we configure sendmail to listen on port 25 and forward all those mails to SAP's port 25000 ?
I dont have much knowledge of sendmail so very confused.
Any idea !!! How to resolve this ?
Thnx
Folks,
I had the same problem, and the issue was that the following file in the kernel was not having the proper permissions, so you need to update permissions of icmbnd file in kernel to 4750 and owner as root.
Then you need to disable sendmail on the server on which port 25 needs to be used by SAP.
Use the command "./sendmail stop" to disable sendmail (cd /etc/rc.d)
Finally try to activate SMTP through smicm tcode.
It worked for me.
thanks!
Similar Messages
-
Hi,
I received message like below from one of my colleague : Is there any work around for configuring the SMTP for Office 365 in ERP6 EHP6.
it is looking good now. After I checked the current situation, I
noticed, that you use office365 as a mailserver.
Sadly this is requiring an authentication method (AUTH LOGIN) which is
not supported by SAP SMTP.
We are also looking for a solution for it, but currently this
authentication is not possible.
Kind regards
Hope you will help me to configure if you are already done....
Thanks in advance...
Regards,
Mathew Vaidyan
29th April 2014So can you kindly let me know for us EHP4 (SAP_BASIS 7.01) what would be the step?
Also in few other forums i have seen with Office 360 with EHP4 configuration is not possible and in few it is possible with intermediate SMTP relay has to be installed.
I have configured and when i try to send an email(External Other domain)am getting the below error in trace log.
27.05.2014
01:37:44
SX_PERFORM_SMTPSEND
G
SMTP Plugin raises error:
27.05.2014
01:37:44
SX_PERFORM_SMTPSEND
G
Could not connect to smtp.office365.com: 25
27.05.2014
01:37:44
SO_SYNCHRON_STATUS_UPDATE
G
Message cannot be transferred to node SMTP due to connection error (final)
I have also tried with the port 587. -
Exchange 2010 route email to SAP smtp server
Hi,
we have a Exchange2010 infrastructure, i need to route email received to a specific address: [email protected], to a SAP smtp server: serverip:25000
How can i obtain this?
Thanks in advanceHi,
Please review note 455140.
Settings on the mail server (SAP-external configuration)
To be able to receive mails in the SAP system, you need to set your mail server so that certain mail addresses are forwarded to one or several SAP systems or clients. For this purpose, you need to define routing rules that assign a mail host and/or port to address areas (generic address parts, usually the domain), for example:
*@crm-prod.company.com --> SAPWASHost:25000
*@crm-test.company.com --> SAPWASHost:25001
For more information about the exact setting procedure, see the mail server documentation.
Thank you.
Best regards,
Ciarán -
Dear All,
We are using Microsoft Exchange Online (Microsoft Hosted Solution for Exchange – Office 365) for sending and receiving emails. Now we want to setup SAP SMTP so that emails / notifications can be sending through SAP via Microsoft Exchange Online. It is quite easy to configure for setting SMTP Services for locally hosted Exchange Server. But this is the first time I am trying to setup for Microsoft Exchange Online.
Current Instance Profile settings are as follows;
is/SMTP/virt_host_1 *:25000
is/SMTP/virt_host_0 *:*
icm/server_port_2 PROT=HTTPS,PORT=44300,PROCTIMEOUT=300,TIMEOUT=600
icm/server_port_1 PROT=SMTP, PORT=1080, TIMEOUT=180
icm/server_port_0 PROT=HTTP,PORT=8000,PROCTIMEOUT=300,TIMEOUT=600
ms/server_port_0 PROT=HTTP,PORT=81$$
SCOT Settings are
Mail Host smtp.office365.com
Mail Port 587
Following are the settings for configuring Outlook for Exchange Online – Office 365;
Server name
Port
Encryption method
POP3
outlook.office365.com
995
SSL
IMAP4
outlook.office365.com
993
SSL
SMTP
smtp.office365.com
587
TLS
Please assist if any one configure office365 with SAP.Hello Majid,
Were you able to setup SCOT for Office365 online, I have to setup same.
Can you help with some guidelines on how you setup.?
Regards,
Ashish -
A port conflict was detected in the server configuration
Hi
Iam getting following error message "A port conflict was detected in the server configuration" error when I run startWeblogic.sh. I checked same in config.sh file about repeatation of port for channel sip but it is not repeated. Please help me out
I have run nodemanager successfully on 5556 port but I have admin server starting problem I tried both $DOMIAN_HOME/startWeblogi.sh and $DOMAIN_HOME/bin/startWeblogic.sh location and I am getting same issue.
Error message:
####<May 4, 2011 10:43:23 AM IST> <Info> <WebLogicServer> <HSCHARTOMR0112> <> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <> <> <> <1304486003957> <BEA-000000> <WebLogic Server "AdminServer" version:
WebLogic Server 10.3.4.0 Fri Dec 17 20:47:33 PST 2010 1384255 Copyright (c) 1995, 2009, Oracle and/or its affiliates. All rights reserved.>
####<May 4, 2011 10:43:24 AM IST> <Notice> <Log Management> <HSCHARTOMR0112> <> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <> <> <> <1304486004002> <BEA-170019> <The server log file /u01/BEA/MW_HOME/user_projects/domains/base_domain/servers/AdminServer/logs/AdminServer.log is opened. All server side log events will be written to this file.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Log Management> <HSCHARTOMR0112> <> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <> <> <> <1304486004005> <BEA-170023> <The Server Logging is initialized with Java Logging API implementation.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Diagnostics> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004044> <BEA-320001> <The ServerDebug service initialized successfully.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004141> <BEA-002622> <The protocol "t3" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004141> <BEA-002622> <The protocol "t3s" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004141> <BEA-002622> <The protocol "http" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004142> <BEA-002622> <The protocol "https" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004142> <BEA-002622> <The protocol "iiop" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004143> <BEA-002622> <The protocol "iiops" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004144> <BEA-002622> <The protocol "ldap" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004144> <BEA-002622> <The protocol "ldaps" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004147> <BEA-002622> <The protocol "cluster" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004148> <BEA-002622> <The protocol "clusters" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004152> <BEA-002622> <The protocol "snmp" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004152> <BEA-002622> <The protocol "admin" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004153> <BEA-002624> <The administration protocol is "t3s" and is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004157> <BEA-002622> <The protocol "sip" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004158> <BEA-002622> <The protocol "sips" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004159> <BEA-002622> <The protocol "sips-admin" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004164> <BEA-002622> <The protocol "diameter" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004165> <BEA-002622> <The protocol "diameters" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Info> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004166> <BEA-002622> <The protocol "diameter-sctp" is now configured.>
####<May 4, 2011 10:43:24 AM IST> <Emergency> <Server> <HSCHARTOMR0112> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1304486004185> <BEA-002633> <A port conflict was detected in the server configuration. The server is configured to listen on two ports that have the same port number and IP address. Channel "sip" address "sip://fe80:0:0:0:fcff:ffff:feff:ffff:5006" conflicts with channel "sip" address "sip://fe80:0:0:0:fcff:ffff:feff:ffff:5006".>
####<May 4, 2011 10:43:24 AM IST> <Critical> <WebLogicServer> <HSCHARTOMR0112> <AdminServer> <main> <<WLS Kernel>> <> <> <1304486004186> <BEA-000362> <Server failed. Reason: Network configuration error, check log for details.>
####<May 4, 2011 10:43:24 AM IST> <Notice> <WebLogicServer> <HSCHARTOMR0112> <AdminServer> <main> <<WLS Kernel>> <> <> <1304486004281> <BEA-000365> <Server state changed to FAILED>
####<May 4, 2011 10:43:24 AM IST> <Error> <WebLogicServer> <HSCHARTOMR0112> <AdminServer> <main> <<WLS Kernel>> <> <> <1304486004281> <BEA-000383> <A critical service failed. The server will shut itself down>
####<May 4, 2011 10:43:24 AM IST> <Notice> <WebLogicServer> <HSCHARTOMR0112> <AdminServer> <main> <<WLS Kernel>> <> <> <1304486004283> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN>
####<May 4, 2011 10:43:24 AM IST> <Info> <WebLogicServer> <HSCHARTOMR0112> <AdminServer> <main> <<WLS Kernel>> <> <> <1304486004283> <BEA-000236> <Stopping execute threads.>
Thanks,
Phani
Edited by: Phani on 3 May, 2011 10:28 PM
Edited by: Phani on 4 May, 2011 1:25 AM
Edited by: Phani on 4 May, 2011 3:03 AMRefer:- wlcs_server1 won't start - sipchannel port conflict
-Akshay -
SMTP Server (port 25) issues on iPhone - IOS 4.1, 4.2.1
SMTP Server Issues ios on iPhone 4.1 / ios 4.2.1
I use an IMAP email account Administered by my company ( I'am administrator in linux/freebsd, etc) and i have it set-up on my iPhone 4 (factory unlocked and NOT jailbreak). The incoming mail server works fine on wifi and 3G Both But the smtp server only works on wifi. If I Attempt to send a message while on 3G Attempts to send the phone for about 5/10/15... and never sent.
perform a downgrade to version 4.1 and the problem remains. Before ios 4.0.1 had no problems.
Testing:
I jailbreak (in 4.1) (only for install net commands in console), install console and "telnet smtp.mycompany.com 25" and time out, but turn wifi and connect; "ping smtp.mycompany" is ok.
Set wifi on, try "telnef smtp.mycompany.com 25" is ok !!!, turn wifi of, try 3G same problem, time out.
Restore no jailbreak 4.1 and try and same problem, restore 4.2.1 no jailbreak and same problem. Try change sim (personal to movistar) and same problem.
BUT!!!!!!! a try:
1) Change in my company smtp server port 25 to 587 (in really dnat 587 to 25).
2) set in my iphone smtp server new port 587 (same smtp server, but ONLY change port)
and ok !!!
I try, jailbreak, install console, telnet smtp.mycompany.com 587 is ok !!!!...
Where is the problem ios 4.1 / 4.1.2 smtp server port 25 ???????
Ios 4.1 / 4.2.1 very very many problems in 3G data in all applications.
apple, please support !! S-U-P-P-O-R-T
STEVE READ : http://en.wikipedia.org/wiki/Technical_support
tatoo support in head please!!!!! support support !!!!!!!nevorask –
Thanks for visiting our forums. I actually had a similar
situation. I had the iPhone 3GS and used it all the time on a FM transmitter in
my car. When I upgraded to the iPhone 4, it wouldn’t work with the FM
transmitter. I never figured out why it wouldn’t work. I would suggest you
continue working with the manufacturer of the device or wait to see if the next
iOS update addresses this issue.
Please feel free to visit us again if you have any other
questions.
Thanks,
Jesus|Senior Social Media Specialist | Best Buy® Corporate
Private Message -
OVM Manager w 2nd NIC = A port conflict was detected in the server config
Greetings,
ENV: Oracle VM 3.1.1.544.
Issue: We had to add/setup a second interface/NIC on a second subnet on Oracle VM Manager. Now, when ovmm is started, we get: <A port conflict was detected in the server configuration. The server is configured to listen on two ports that have the same port number and IP address. Channel "https" address "https://fe80:0:0:0:26b6:fdff:fec8:f4b1:7002" conflicts with channel "https" address "https://fe80:0:0:0:26b6:fdff:fec8:f4b1:7002".>
BEA Docs (http://docs.oracle.com/cd/E13222_01/wls/docs92/messages/Server.html)
BEA-002633: Emergency: A port conflict was detected in the server configuration. The server is configured to listen on two ports that have the same port number and IP address. Channel "channel1" address "url" conflicts with channel "channel2" address "url".
Action: Please ensure that the address identities [ListenAddress and ListenPort combinations] are distinct and unique.
Would you happen to know which file, (i.e. config.xml), and which lines (i.e. <listen-address>) we need to edit, with the correct syntax to add a second IP address/subnet to our WebLogic server?
Thank you in advance for your support!
Regards,
RoddyThank you for your support!
1. What version of Linux? OL 62 x64
2. Have you set a separate DNS name for the second interface IP? No, although we are using/setup dnsmasq on the second interface/eth3 to dish up DNS on the private network. DNS name resolutions works like a charm on the private vlan.
3. Do you still have a single default route or are you trying to use more than one? The second interface is in a private unroutable network. the front end network/NIC eth0 is routable and on a public network.
Public/Private Network Setup:
* Public network with oracle vm manager on eth0/10.4.x.x. This is how we access the ovm manager GUI, and ssh to manager, and via manager ssh to the dom0s. The dom0s are on private nonroutable networks available via the manager host's eth3.
* Private networks accessible via the oracle vm manager host eth3/802.1q/VLAN xxx. this is the server management network channel, this vlan is not routable. We have two other vlans, i.e. heartbeat and live migration, both also not routable.
Thoughts? -
Hi all,
i try to install N1 1.3 but i have an error.
Solaris 10 U6
There is no 8083 port in /etc/services.
Nothing in netstat -an and nothing in lsof.
Could you help me please?
N1SM Installer (version 1.3 on SunOS)
1. Install OS packages. [Completed]
2. Install Expect. [Completed]
3. Install IPMI tool. [Completed]
4. Install JDK 1.5. [Completed]
5. Install service provisioning components. [Partially Run]
6. Install OS provisioning components. [Not Completed]
7. Copy DHCP configuration file. [Not Completed]
8. Install user interface components. [Not Completed]
9. Install service container components. [Not Completed]
10. Install N1 System Manager. [Not Completed]
Failed Step: Install service provisioning components.
The following is a portion of the installer
log which may indicate the cause of the error.
If this does not indicate the cause of the
error, you will need to view the full log
file. More information on how to do that is
available below.
Checking port 1130 using netstat
Checking port 1131 using netstat
Checking port 8083 using netstat
Checking port 8083 using telnet
The installer has detected that there may be a port conflict with current running processes. Please stop the processes which are using the following conflicting ports: 8083
Please fix the problem and then try this step again.
For a full log of the failed install see the file: /var/tmp/installer.log.1461.
t. Try this step again (correct the failure before proceeding)
x. Exit
Enter selection: (t/x)N1SM is EOL and if you really must install it, the latest is 1.3.3 + patches, please do install in a CLEAN, DEDICATED machine (which should relief you of your problem).
N1SM approaches EOSL - meaning it will not be supported soon, or IF, then for large amount of $$$
I strongly suggest you to talk to your Sun peers for xVM Ops Center 2.0 deployment, which replaced N1SM 2 years ago
L -
Port conflict error when trying ot run the page.
Hi ,
Below is the error message whern I try to run the page.How to resolve it.
I tried checking tools->preferences->embedded oc4j->Host name to default local ip address and local host name
Another trial was : open Task Manage ->Process tab..if there will be two process jdevw and javaw. Terminated those process and then start JDeveloper and run the page,it should work , but i could find only java.exe running.
Appreciate your help.Thanks.
**** JMS port conflict detected. The JMS port will be reassigned to port 9236.
[Starting OC4J using the following ports: HTTP=8995, RMI=23892, JMS=9236.]
D:\MC\oajdev\jdevbin\jdk1.4.2\bin\javaw.exe -client -classpath D:\MC\oajdev\jdevbin\j2ee\home\oc4j.jar;D:\MC\oajdev\jdevbin\jdev\lib\jdev-oc4j.jar -Xbootclasspath/p:D:\MC\oajdev\jdevbin\jdev\appslibrt\ojdbc14.jar;D:\MC\oajdev\jdevbin\jdev\appslibrt\nls_charset12.zip -DFND_JDBC_STMT_CACHE_SIZE=200 -DCACHENODBINIT=true -DRUN_FROM_JDEV=true -mx256m -Xverify:none -Doracle.j2ee.dont.use.memory.archive=true -Doracle.j2ee.http.socket.timeout=500 com.evermind.server.OC4JServer -config
D:\MC\oajdev\jdevhome\jdev\system9.0.3.5.1312\oc4j-config\server.xml
[waiting for the server to complete its initialization...]
Fatal Error: Unable to write to the transaction log (/D:/MC/oajdev/jdevhome/jdev/system9.0.3.5.1312/oc4j-config/log/transaction.state), possible reasons for this are that Orion lacks permission to write to the file, or that another instance of the server is already running with this configuration (most common): Unable to alter transaction log
Process exited with exit code 1.You have other JDev session running.
Probably your first JDev session was not terminated gracefully.
Close ALL JDev sessions. Go to Task Manager and kill any process related to JDev.
Then open JDev again. You should not get this error message again.
PS. Despite of this message, you will be able to continue with your work. -
Can receive but can't send mail via BT Yahoo SMTP server port 995
Suddenly I can't send mail from my BT/Yahoo account but can still receive mail. The message that i get is that it was rejected by the server. I have not changed the server - it is still SMTP via port 995, using SSL. Help!! Why should this have ocurred out of the blue and what do I do?
Hi Dancing Brave,
Thanks for visiting Apple Support Communities.
I recommend starting with the steps in this article if you are not able to send mail:
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/ts3276
Best,
Jeremy -
Smtp outgoing (port 25) blocked after upgrade
Since upgrading to mavericks, all outgoig access on port 25 never connects.
I havd upgraded 2 machines - One is working and the other is not work. Both machines were working before the upgrade.
This is NOT just related to the mail client - It affects port 25 outgoing at the telnet level.
Does anyone have an answer to this yet?
TimHi Layman,
According to your description, my understanding is that you want to configure the SMTP to use port 465 for outgoing email in SharePoint.
Per my knowledge, Exchange server will secure communication over any port, but will not use SSL, so there is only TLS encryption in SMTP.
To use port 465, we can add the port 465 under Network tab to the Receiver Connector for SharePoint Outgoing email. And then TCP port number on Outbound Connections in
DSMTP Virtual Server properties.
More references:
http://blogs.technet.com/b/tirumals/archive/2012/03/17/step-by-step-configuration-of-outgoing-emails-from-sharepoint-to-microsoft-online.aspx
http://support.microsoft.com/kb/829721/en-us
http://social.technet.microsoft.com/Forums/exchange/en-US/8dc08cf8-8662-4a02-a181-f821e8d59d06/exchange-smtp-using-port-465?forum=exchangesvrgenerallegacy
For more information, you can post your question to the forum for Exchange: http://social.technet.microsoft.com/Forums/exchange/en-US/home?category=exchangeserverlegacy .
More experts will assist you, then you will get more information relation to Exchange.
Best regards.
Thanks
Victoria Xia
TechNet Community Support -
Messaging Server 3.x: Configuration of SMTP-accept port number
This article describes how to change the SMTP-accept port used by Netscape
Messaging Server 3.x for receiving mail. The default port is 25.
<P>
This configuration works with virus detection software like Trend Micro.
<P>
(See attachment)Hi there
if have sucessfully run the iplanet smtp server on different port then 25 then kindly let me know how to achive that , bcoz even i wanna do that
regards
Prashant -
Hi all,
In the receiving and sending port for an IDoc we have the concatenation of SAP with system id.
This is supposeldy a port hence I was wondering why we cannot see its definition in WE21 ?
And how does a system decide whether the destination/receiving port exist or not if not defined in WE21 ...
Please guide .. looked in ?BD64 also but no help
Regards,
SugopaHello,
I don't know IDOC, but that I know, SAP listen the port of : 30 + ID number. For exemple if you are the ID 01, your SAP will listen 3001.
Try telnet sap_host 30xx
Frederic -
R12 OPMN port Conflict with RAC CRS
i'm facing problem with port conflict.
when i stop ora.linux1.ons and ora.linux2.ons
iam able to start application services and when ora.linux1.ons and ora.linux2.ons are up and running im not able to start application tier services.
Please help
ThanksWhat is the port used by the application and by ora.linux1.ons and ora.linux2.ons?
ons.conf
localport=6100 # line added by Agent
allowgroup=true
usesharedinstall=true
remoteport=6200 # line added by Agent
nodes=linux1:6200,linux2:6200 # line added by Agent
~
i have configured RAC on R12.1.1 db-11gr2.
im trying to start application tier services but when i o that
sh adstrtal.sh apps/apps
You are running adstrtal.sh version 120.15
The logfile for this session is located at /d01/oracle/PROD/inst/apps/PROD_linux 1/logs/appl/admin/log/adstrtal.log
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adopmnctl.sh start
script returned:
You are running adopmnctl.sh version 120.6
Starting Oracle Process Manager (OPMN) ...
adopmnctl.sh: exiting with status 2
adopmnctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl /admin/log/adopmnctl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adalnctl.sh start
script returned:
adalnctl.sh version 120.3
Checking for FNDFS executable.
Listener APPS_PROD has already been started.
adalnctl.sh: exiting with status 2
adalnctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/ admin/log/adalnctl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adapcctl.sh start
script returned:
You are running adapcctl.sh version 120.7.12010000.2
Starting OPMN managed Oracle HTTP Server (OHS) instance ...
adapcctl.sh: exiting with status 2
adapcctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/ admin/log/adapcctl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adoacorectl.sh start
script returned:
You are running adoacorectl.sh version 120.13
Starting OPMN managed OACORE OC4J instance ...
adoacorectl.sh: exiting with status 2
adoacorectl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/admin/log/adoacorectl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adformsctl.sh start
script returned:
You are running adformsctl.sh version 120.16
Starting OPMN managed FORMS OC4J instance ...
adformsctl.sh: exiting with status 2
adformsctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/admin/log/adformsctl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adoafmctl.sh start
script returned:
You are running adoafmctl.sh version 120.8
Starting OPMN managed OAFM OC4J instance ...
adoafmctl.sh: exiting with status 2
adoafmctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/admin/log/adoafmctl.txt for m ore information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/adcmctl.sh start
script returned:
You are running adcmctl.sh version 120.17.12010000.3
Starting concurrent manager for PROD ...
Starting PROD_1231@PROD Internal Concurrent Manager
Default printer is noprint
adcmctl.sh: exiting with status 0
adcmctl.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/admin/log/adcmctl.txt for more information ...
.end std out.
.end err out.
Executing service control script:
/d01/oracle/PROD/inst/apps/PROD_linux1/admin/scripts/jtffmctl.sh start
script returned:
You are running jtffmctl.sh version 120.3
Validating Fulfillment patch level via /d01/oracle/PROD/apps/apps_st/comn/java/classes
Fulfillment patch level validated.
Starting Fulfillment Server for PROD on port 9300 ...
jtffmctl.sh: exiting with status 0
.end std out.
.end err out.
All enabled services for this node are started.
adstrtal.sh: Exiting with status 0
adstrtal.sh: check the logfile /d01/oracle/PROD/inst/apps/PROD_linux1/logs/appl/admin/log/adstrtal.log for mor e information ...
[applmgr@linux1 scripts]$
Thanks
Edited by: Maverick on Dec 31, 2010 4:11 AM -
P45D3 Platinum - does the esata (external) have port multiplier ability?
Hi,
have the MSI P45D3 and just bought the Icydock mb561us-4s (http://www.icydock.com.tw/English/mb561us-4s_frame.html)
which requires the esata to have port multiplier function.
Does the esata have it.....if yes....please help with instructions to enable it.
TxHi,
the onboard eSATA port is hosted by a JMicron JMB362 Chipset, which (according to the JMicron product specifications) supports the following:
http://www.jmicron.com/Product_JMB362.htm
Quote
Port Multiplier with Command-based Switching
Quote
• Supports Port Multiplier with Command-based Switching on SATA II port
Maybe you are looking for
-
Export To PDF in CRYSTAL REPORT XI Release 2
I am using Crystal report XI release 2. Font Size is decreasing when I am exporting Crystal Report to PDF. It was working fine previously but i don't know what messed it up. Please help.
-
Random Intenet Drops for a Few Seconds
Hi all, my first post on here. I was hoping to get this issue fixed with a tech visit, but of course, that didn't happen. I started my 105 mbps internet service about a month ago. I am using the Technicolor Xfinity modem that is currently being ren
-
Smartforms - Change a text elements character Format
Hello, I need to modify a Smartform by increasing the font size on some text elements. When I highlight the text element to change and then click the dropdown for Character Format I can click the format I would like but it never changes. I've also t
-
Hi folks. Just grabbed the May 2 snapshot of ffmpeg, and she won't install. *make(6189) malloc: * vm_allocate(size=4272951296) failed (error code=3)* *make(6189) malloc: * error: can't allocate region* *make(6189) malloc: * set a breakpoint in szone_
-
Perte du grain en passant de Camera Raw a CS3
Bonjour, Quand je devellope un RAW via le Camera Raw du CS3 version 4,6, je perd le grain créé sur le RAW. Je suis en Grayscale. Mon image a du grain sur Camera RAW et en l'ouvrant sur CS3, le grain n'apparait pas et elle est plus floue avec un manqu