Set as-path prepend last-as doesn't work ?

I'm trying to use this statement on a route-map to an IBGP peer in order to make a particular AS-PATH to appear longer but it doesn't seem to be working.
Here's my route-map, which is applied inbound from the neighbor I want to pad. It seems so logical yet it isn't working.
Any ideas would be welcomed.
= K
route-map Groom_Cogent permit 100
match as-path 174
set as-path prepend last-as 2
ip as-path access-list 174 permit ^174_

If you look at the BGP decision process:
http://www.cisco.com/en/US/tech/tk365/tk80/technologies_tech_note09186a0080094431.shtml#bestpath
You'll see that one of the steps is the IGP metric (step 8). So, if all other factors are equal up to the IGP metric, and it sounds like they are, as long as the IGP cost to reach the next hop along one path is shorter in one direction, that direction will be chosen. It seems to me that setting the IGP metrics so the one path is chosen over the other one is the thing to do here, if you don't want to use local pref.
It's also possible to use a cost community within your AS to inject a new "cost" into the decision algorithm.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1829/products_feature_guide09186a00801bbad4.html
The current insertion point is just after the IGP metric, which sounds perfect for what you are doing, if the IGP metrics are all the same.
Hope that helps...
Russ

Similar Messages

Set AS-PATH prepend by matching RT value during import

Hi,
Can some one please explain how to match RT value and set AS-PATH prepend while importing the routes in to a VRF ?
I know AS-PATH prepention can be done with export-map when exporting routes along with setting a RT value. But for some reason this can't be done while importing to the VRF. Please help
Thanks in advance,
Anil.

Anil,
I did some more research and tested it to be working. you were not able to set AS-PATH prepend in an import-map due to the following bug.
I tested the workaround in my lab. If you set local-preference along with as-path prepend then it works fine.
CSCtj85371 Bug Details
import map with as-path prepend
Symptom:
AS_PATH prepend will only work if there is LOCAL PREF defined inside a outbound routemap. If there is only AS_PATH prepend and no LOCAL_PREF, BGP will not prepend the paths with defined AS values.
Conditions:
AS PATH prepend will not be pre-pended properly
Workaround:
Configure LOCAL_PREF along with AS_PATH prepend
Fixed-In
15.0(1)M4.5
15.1(3.13)T
12.2(33)SRE3
12.2(33.2.20)SRE
15.1(1)S0.2
15.1(1.22)S
15.0(1.19)DPA12
15.1(3.8.3)PIB
15.2(0.0.12)PIL16
15.0(1)S2.3
15.1(2)T2.2
15.1(1)T2.4
15.1(3)T0.2
15.1(1)S1
15.0(1.19)DPB23
15.0(2.12)DPB1
15.0(1)SY
15.1(1)SG1.3
15.0(1)S3a
15.1(2)GC1
15.1(1)MR3

[svn] 3610: Fixing bug SDK-17173: Setting rotate to a large number doesn' t work anymore.

Revision: 3610
Author: [email protected]
Date: 2008-10-13 17:33:25 -0700 (Mon, 13 Oct 2008)
Log Message:
Fixing bug SDK-17173: Setting rotate to a large number doesn't work anymore.
The Flash Player clamps rotate between -180 and 180. We should do the same now that we're doing some of the calculations ourselves. This clamping logic was added to CompoundTransform.as. Also, clamping logic was added to UIComponent. This is because FP10 doesn't handle values greater than 2^15-1; FP 9 used to handle these values fine. I filed a FP bug for this (FP-749).
QE: Yes - Please look out for any rotation failures
Doc: No
Bugs: SDK-17173
Reviewer: Ely
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-17173
http://bugs.adobe.com/jira/browse/FP-749
http://bugs.adobe.com/jira/browse/SDK-17173
Modified Paths:
flex/sdk/trunk/frameworks/projects/framework/src/mx/core/UIComponent.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/geom/CompoundTransform.as

Can we now assume that the touch SDK has been abandonned by Adobe? It's now a year after "should be updated soon", and currently if you try to download the touch SDK from this page you get the Photoshop 3 SDK instead!!!
I ask as I'm about to remove Touch support from my app; the very few people that use touch are now having problems e.g., timeouts, with the latest version of Photoshop.
Sandy

HT1725 I bought an App last month, doesn't work. consulted the manufacture they sent me to iTunes for refund, reported the problem to iTunes, they sending me back to Manufacturer.

I bought an App last month, doesn't work. consulted the manufacture they sent me to iTunes for refund, reported the problem to iTunes, they sending me back to Manufacturer. Can someone please assist me on this, I need my refund for this non functional App. BSSoft and iTunes Stores do something here, when I go back to report it again, I get an error message stating "...this problem has been reported or too old to report..."

Debit card? Are you sure?
USA iTunes Store does not appear to accept debit cards - http://www.apple.com/legal/itunes/us/terms.html "The iTunes Store, Mac App Store, App Store, and iBookstore services (“Services”) accept these forms of payment: credit cards issued by U.S. banks, payments through your PayPal account, iTunes Cards, iTunes Store Gift Certificates, Content Codes, and Allowance Account balances."

Server 2008 r2 setting up firewall rule that just doesn't work!

I have allocated static ip addresses to a group of PCs, then gone to Server 2008 r2 and gone to Windows firewall with advanced security and written a new custom rule. Am blocking internet explorer, have browsed to where it is lodged on PCs, added the ip
addresses for blocking, in fact followed a detailed set of instructions but it just doesn't work! I am at a loss as to why, can anyone help please, driving me mad now! Thanks.

Are you applying ADV firewall rules through GPO. If not then you need to create block rules on the clients i think. but I would create a block rule in GPO and link to these PC's OU.

UpDated Flash Player last week doesn't work previous ver worked fine

I updated last week when it prompted me to, now websites that i used to use will not work. it just gives me a blank area where the flash animation should be. I have figured out that it has something to do with my firewall. When i disable the firewall flash works with it running it doesn't. I have tested this with http://www.adobe.com/software/flash/about/ . I don't understand why this ver is causing my firewall to block it. I have all the permission i need and the install was run as admin. I have tried reinstalls and using C/Windows/System32/Macromedia/Flash. I think i just need to change a setting on my firewall but i can't find where the addon is since i'm using firefox, i wish i never updated
setup: Vista Bus, Firefox, CA firewall, Flash Ver 10.0.22.87

I have the same problem...I downloaded around noon today and have been trying to figure out all day what is going on. You're situation sounds identical to mine. I was going to play a game that I play regularly and I got in just fine this morning and then at noon it told me to download an updated version of Flash Player I did and it still doesn't work. I really hope someone can answer the question.

When you will release a new java update ? With the last it doesn't work correctly ( java 3d )

I use java 3d, but with the last update it doesn't works with any browser

"When you will release a new java update ?"
"We" don't release anything; we're not Apple, we're just users like you.
Use the feedback form to send queries to Apple.
http://www.apple.com/feedback/macosx.html

Can't set up windows on bootcamp, keyboard doesn't work

okay, i wait through the agony of the windows install non-sense, and it comes up to the part where i have to set up windows (name, accounts, etc.). But when i go to enter all my info, my keyboard doesn't work, or my mouse for that matter. I have a 24" iMac with the wireless keyboard and mouse. I don't know what to do!
Message was edited by: jayqUon

Jay:
Below is excerpt I took from [HERE|http://support.apple.com/kb/HT1461] which mandates using an internal keyboard or a USB keyboard/mouse to install Windows via boot camp.
Requirements
To use Boot Camp, you need:
1. *An Intel-based Macintosh computer with a built-in or USB keyboard and a built-in trackpad or USB mouse.*
2. Mac OS X 10.5 or later
3. The latest firmware updates available for your Intel-based Mac.
4. At least 10 GB of free space on your startup disk (single partition).
5. A full, single-disc version of Windows Vista, Windows XP Home Edition or Professional with Service Pack 2 or later. Boot Camp does not include Windows. You must provide your own properly licensed installation disc.
Important: A Windows XP installation disc must include Service Pack 2 (SP2). You cannot install an earlier version of Windows and upgrade to Windows XP, nor install an earlier version of Windows XP and update it to SP2.
6. Boot Camp Assistant (find it installed in /Applications/Utilities/ on Leopard).
Axel F.

Last update doesn't work

Hi!
I just update flash player(14.0.0.125) and now i can't watch videos or play games. I used firefox so I tried with Explorer and Chrome but it doesn't work either.
I went to the adobe help page but nothing there help me.I have Windows 8 (64-bit). Thank you

Apple, please can you fix asap? Our company uses GDrive as a standard for all files including Numbers spreadsheets created on Mac and use iPad's to edit on the the road. With new version of iWork we've come to a sudden halt no longer being able to do so. Not practical to move all spreadsheets out of 100's of GDrive folders that contain common files by client into iCloud. To fix need an option to save Numbers sheet from Mac as a .ZIP file as the iPad does when you open the sheet in GDrive from Numbers on iPad. Please get onto this soonest, IT is talking switch iPads to Surface and back to Office from iWork.

GT70 2OC iCharger BIOS setting (S0, S1, S2...) doesn't work?

I enabled the iCharger setting to support charging in the various S states (sleeping, powered off, etc) and it doesn't seem to work. When I connect an iPhone or any other device that charges via USB, the charging happens normally as long as the computer is awake and the lid is open. But the moment I close the lid, putting the computer to sleep, or power it off, the USB-connected device immediately stops charging.

1. I guess so.
2. I am not sure but according to MSI, you better not to cross flash EC firmware to prevent from uncertain damage.
3. No.

Setting primary monitor in xorg config doesn't work

I have the following stored as `10-monitor`:
Section "Monitor"
Identifier "DVI-0"
Option "Primary" "true"
EndSection
Section "Monitor"
Identifier "DVI-1"
Option "RightOf" "DVI-0"
EndSection
When I start, both monitors are connected properly, but looking at `xrandr`, none is set as primary.
I need to manually set `DVI-0` as `--primary` and restart i3 for everything to work properly.
PS: I previously mentioned this briefly in another topic: https://bbs.archlinux.org/viewtopic.php?id=181469
Any idea what might be wrong or what log output I should be looking for?

Where you set the measurement ?
Did you follow this ?
@ Report Object Navigator
1. Select Layout Model >> Main Section then properties
set Width, Height and Orientation under Section
Adjust your layout and
Try...
Hope this works..

I've set 2 aliases in my iCloud Account and want to set a 3. one but it doesn't work

In my iCloud Account i have 2 Aliases transfered from Me.com. When i set up iCloud on my Mac i see one another alias that i had on Me.com, i can choose it as the despatcher adress but it is not listed as an alias in my ICloud.com Account.
My Problems are:
1. how can i delete the alias that is on my mac but nowhere else? (it is an [email protected] adress)
2 How can i create a new Alias in iCloud? Remeber i have only 2 Aliases listed in iCloud so it should be possible to create a third one
Thanks for your responses!!
Cheerz David

Hello Chris,
Thanks for your answer. I was hoping for an easier answer. Too bad there is no drag and drop solution, it would have been much easier.
Thanks for answering so fast.
Bye.
Yan

Back to the last menu doesn't work (bluray)

Hello!
Here's my problem: I have several menus (in different languages) that sometimes leads to the same video (for example, a button in french menu leads to the same track as a button in the german menu). I want that if the user presses "menu" his remote control, he goes back to last menu (if he comes from the french menu, I want the bluray to go back to french menu). To do that, i selected "go back to last menu" in every sequence. It works correctly when i simulize the navigation in the viewer, but when i burn the bluray, when I press menu, the disk don't even goes back to french nor german, it goes back to the main menu of the disk.
I tried to choose "go back to last menu" in the disk asset for the "title button" but it's in grey and i can't choose it.
Do someone have a solution?
Tank you,
Michaël

I used to do it manualy on DVD Studio pro because it allows to use script and to tell to your player from witch menu you come from. but here i don't how to manage the routing to five differents menus. An also, even if route correclty the link after the track, I have to find a way to go back to previous menu and not to the top menu...
I join four screen shots. You have example of 3 differents menu and the las on the bottom "viskose bitkisel" "Oreillers Visco Végétale" lead to the same track (the 4h screenshot) "oreillers memo sensitifs"

Setting page layout in Reports 6i doesn't work, gap gets to big.

We are forced to use good old' Oracle Reports 6i because another application uses this to create its forms and reports. The problem is, that we want to print those reports on continuous paper with specific measures. In millimetres it would be 210 mm x 305 mm. We already set the measures of the main part report to those specifications, but it appears that this wasn't enough.
If the report is printed straight from Reports 6i, the first page is all ok, but the second one has an offset of about 10 mm. This offset gets higher on every page, so approximately on page 4, the page is already partly on the next page of the continuous paper. This problem really drives me crazy.
I have studied this forum for a whole afternoon, but I couldn't find an answer. I have read many posts regarding the margin "bug" of Reports 6i, which seems to influence this particular report. As I am completely new to reports and Reports 6i in particular, I would love to get a helping hand here at the forums. Maybe someone can support me here.
Many thanks in advance!

Where you set the measurement ?
Did you follow this ?
@ Report Object Navigator
1. Select Layout Model >> Main Section then properties
set Width, Height and Orientation under Section
Adjust your layout and
Try...
Hope this works..

Time since last charged doesn't work

Does anyone else have this problem --- under general in settings, under the title Time since last charge....there is usage and stand by. After both of those it just has this - I've contacted apple, they ran a thing to see if it was the battery and it wasn't. They had me restore the ipad. When I restored it to last back up than it worked for like a day. So than they had me restore to new and it just reads - So idk what to do next....afraid there is something wrong with the hardware. Help

Reset it by holding the power and home keys down until the Apple logo appears.
Barry

Set as-path prepend last-as doesn't work ?

Similar Messages

Maybe you are looking for