Setup NIC priority in OS X

Hi,
All my Macs are connected to the LAN (wired) and to a isolated wifi network.
Some Macs are registering in the DNS with the IP of the Wifi network instead of the IP from the LAN (wired network).
Can you tell me how to force the Macs to register in the DNS with the LAN IP (wired) instead of Wifi?
I know how to do this on Windows clients but not on the Macs.
Thank you.
N.

Hi,
sorry to bother you once again, do you know how to change NIC order via the Terminal?
I have found the command "networksetup -listnetworkserviceorder" but I cannot change the order with this command.
Thank you once again.
N.

Similar Messages

Can I setup process priority on WebLogic?

Hi,
I try to find out if WebLogic provides any process priority features ?
Using JMS message property field is one way. Are there any other
alternatives?
Chris

Not yet. We do not allow prioritization of given services. This is
something we plan to add in a future release.
Michael Girdley
BEA Systems
Learning WebLogic? http://learnweblogic.com
"Chris Chen" <[email protected]> wrote in message
news:3a71152e$[email protected]..
Hi,
I try to find out if WebLogic provides any process priority features ?
Using JMS message property field is one way. Are there any other
alternatives?
Chris

NIC Bonding not behaving as it should

Hi Folks, am trying to setup NIC bonding on my VM (OEL5u6) having two virtualised NICs, i have done the setup which is quite simple however my active-backup mode is not working as expected.
My Bonded interface
[root@Gateway network-scripts]# cat ifcfg-bond0
DEVICE=bond0
IPADDR=192.169.25.2
NETMASK=255.255.255.248
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
BONDING_OPTS='mode=active-backup miimon=1000'
TYPE=Ethernet
individual interfaces
[root@Gateway network-scripts]# cat ifcfg-eth2
DEVICE=eth2
HWADDR=08:00:27:1e:57:cf
MASTER=bond0
SLAVE=yes
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
[root@Gateway network-scripts]# cat ifcfg-eth4
DEVICE=eth4
HWADDR=08:00:27:46:69:69
MASTER=bond0
SLAVE=yes
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
Bonding status (looks good)
[root@Gateway network-scripts]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth2
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth2
MII Status: up
Link Failure Count: 0
Permanent HW addr: 08:00:27:1e:57:cf
Slave Interface: eth4
MII Status: up
Link Failure Count: 0
Permanent HW addr: 08:00:27:46:69:69
I am doing a continous ping from another host in the same n/w to this bonded interface IP to check if the ping streak breaks when i test this setup
Testing -
[root@Gateway network-scripts]# ifenslave -c bond0 eth4
and that's it my SSH connection is gone, and ping is broken with "Request timed out"
when i check the bond status now -
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth4
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth2
MII Status: up
Link Failure Count: 0
Permanent HW addr: 08:00:27:1e:57:cf
Slave Interface: eth4
MII Status: up
Link Failure Count: 0
Permanent HW addr: 08:00:27:46:69:69
am afraid there's not much help in the message log to debug this.
Any views what's wrong and how to resolve? appreciate ur replies. Thanks
Regards Amit

Hi,
I'm having the same problem, when i disconnect the cable from the eth0 (active slave) stop receiving respond
I have tried bridged conf and interal net.
I'm using VirtualBox 4.1.16
This is my conf:
[root@integrador ~]# cat /etc/sysconfig/network-scripts/ifcfg-bond0
DEVICE=bond0
IPADDR=10.10.0.2
NETWORK=10.10.0.0
NETMASK=255.255.255.0
BONDING_OPTS="mode=1 miimon=100"
BOOTPROTO=none
ONBOOT=yes
[root@integrador ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes
USERCTL=no
[root@integrador ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
ONBOOT=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes
USERCTL=no
[root@integrador ~]# cat /etc/modprobe.d/bonding.conf
alias bond0 bonding
[root@integrador ~]# ifconfig -a
bond0 Link encap:Ethernet HWaddr 08:00:27:5C:C5:BA
inet addr:10.10.0.2 Bcast:10.10.0.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe5c:c5ba/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:402 errors:0 dropped:0 overruns:0 frame:0
TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:39487 (38.5 KiB) TX bytes:11045 (10.7 KiB)
eth0 Link encap:Ethernet HWaddr 08:00:27:5C:C5:BA
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:211 errors:0 dropped:0 overruns:0 frame:0
TX packets:89 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:23061 (22.5 KiB) TX bytes:10863 (10.6 KiB)
eth1 Link encap:Ethernet HWaddr 08:00:27:5C:C5:BA
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:191 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:16426 (16.0 KiB) TX bytes:182 (182.0 b)
eth2 Link encap:Ethernet HWaddr 08:00:27:DF:11:A2
inet addr:192.168.57.1 Bcast:192.168.57.3 Mask:255.255.255.252
inet6 addr: fe80::a00:27ff:fedf:11a2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1142 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:119508 (116.7 KiB)
eth3 Link encap:Ethernet HWaddr 08:00:27:D1:41:9A
inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fed1:419a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:825 errors:0 dropped:0 overruns:0 frame:0
TX packets:625 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:563221 (550.0 KiB) TX bytes:85914 (83.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:25 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2690 (2.6 KiB) TX bytes:2690 (2.6 KiB)
[root@integrador ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 08:00:27:5c:c5:ba
Slave queue ID: 0
Slave Interface: eth1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 08:00:27:fc:6b:f6
Slave queue ID: 0
[root@integrador ~]# lsmod | grep -i bond
bonding 109558 0
ipv6 264641 39 cnic,bonding,ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6
[root@integrador ~]# uname -a
Linux integrador 2.6.32-220.el6.i686 #1 SMP Tue Dec 6 16:15:40 GMT 2011 i686 i686 i386 GNU/Linux
Sorry for my english!

NIC Teaming on Dell Servers

I am using BASP to setup NIC teaming on a Dell R720 server. My understanding is that both of the following teaming methods supports load balancing/sharing. ie: team with 2 NIC cards (1gbps each) I will get 2gbps throughput. Am I right?
• Smart Load Balancing and Failover
• Link Aggregation (802.3ad)
If I were to setup LACP, is it mandatory to define native vlan? Is the following command holds good?
interface Port-channel100
switchport trunk encapsulation dot1q
interface GigabitEthernet 0/1
description Uplink to Server (NIC-1)
switchport access vlan 100
switchport mode access
channel-group 100 mode active
spanning-tree portfast
interface GigabitEthernet 0/2
description Uplink to Server (NIC-2)
switchport access vlan 100
switchport mode access
channel-group 100 mode active
spanning-tree portfast

That's what I indicated in my original answer: The access VLAN and switchport modes should be defined on the Port-channel100 interface as well as the member interfaces if you want the bundle to actually be on VLAN 100.
Defining "spanning-tree portfast" ("spanning-tree portfast trunk" for 802.1q) on the Po100 interface should be done for servers. Once you set it on the Po100 interface, it should reconfigure the member interfaces automatically.

NIC Teaming question

Hello All,
I'm setting up a new 2012 R2 server. It will be our new AD/DNS/DCHP server. Question is if I setup NIC teaming, Should I point the client computers DNS to the virtual IP Team NIC address?
Thanks!
JnB

Hi!
If you setup NIC teaming, you get presented a "teamed adapter". You do all your IP config on this thing.
You can't do any config on the members of the team (e.g. Ethernet 1, Ethernet 2). You'll see they just have the Multiplexor Protocol configured.
So yep, you'll configure the team, do everything on the teamed adapter. Point your computers to that IP.

QoS Setup for Whatsapp and VOIP application

Hello guys,
                    I own a WAG320N modem. I wasnted to setup QoS priority for 2 applications "Whatsapp" and a VOIP application which allows me to call from a computer to a mobile phone. I use torrent applications and they take all the bandwidth. Hence i was looking to configure QoS for these two applications.
                     I went to the QoS page and they are asking about the application details such as port range etc. I don't know what value to be filled. I have posted a screenshot below of what its asking. Can anyone help me fill these details for both applications.
Thank you in advance
Image: http://i40.tinypic.com/2qi02z5.jpg
Solved!
Go to Solution.

You can basically add Viber on the QoS. Under Applications and Gaming, click on QoS then enable the Internet Access Priority. On the Catergory, look for Applications>Add a New Application. Then you can enter the name of the Application. You may now add the port numbers. And since it's a specific port and not range, you do it this way;
   5242 - 5242 TCP (for the protocol)
   4244 - 4244 TCP
   5243 - 5243 UDP
   9785 - 9785 UDP
Hope this helps.

Galaxy s6 email priority senders - sound notification

I setup my priority email senders in my new Galaxy s6 (email settings/notifications/priority senders on & notifications on). But I think it works differently from my old s3. On the s3 I would get a notification sound whenever I received an email from a priority sender.
In the s6, I get a sound notification, but it seems to be whenever my priority sender is on the email string at all. I only want to receive it if they sent a message (or replied).
(Also, I would like to just get priority sender notifications only, but you have to turn on ALL notifications to get the priority sender.)
Anyone else tried this on the s6?

I realize it's important to have your notifications set up correctly, scarr2009. Have you seen this behavior ever since establishing the priority senders? Are you using the preinstalled email application?
AndreaS_VZW
Follow us on Twitter @VZWSupport
If my response answered your question please click the "Correct Answer" button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

Sugg. Ship date not conceder priority rule (SSD)

ECC plan not conceder Sugg. ship date.
below example for one End item (FG Item)
sugg due date                   sugg. ship date
3 may-2014                    11 June-2014
10 may-2014                    12 June-2014
24 may-2014                    24 may 2014
31 may 2014                    14 july 2014
We are on priority pegging. Please suggest.

Well i din't understand your concern. Throw some light on the way you have setup the priority rules and the behavior from plan your are looking for
with some data from the backend tables , if possible.

Jackd + guitar: "timeouts and broken pipes"

Hi friends! I'm trying to pass my electric guitar via any rack/effects (like Guitarix or Creox) with no luck. I've got this sound card:
01:06.0 Multimedia audio controller: Creative Labs [SB Live! Value] EMU10k1X
01:06.1 Input device controller: Creative Labs [SB Live! Value] Input device controller
I try with QJackCtl and invoking jackd from the terminal with any luck.
jackd -d alsa -C -P
jackd 0.121.3
Copyright 2001-2009 Paul Davis, Stephane Letz, Jack O'Quinn, Torben Hohn and others.
jackd comes with ABSOLUTELY NO WARRANTY
This is free software, and you are welcome to redistribute it
under certain conditions; see the file COPYING for details
could not open driver .so '/usr/lib/jack/jack_net.so': libcelt0.so.2: cannot open shared object file: No such file or directory
could not open driver .so '/usr/lib/jack/jack_firewire.so': libffado.so.2: cannot open shared object file: No such file or directory
JACK compiled with System V SHM support.
loading driver ..
creating alsa driver ... hw:0|hw:0|1024|2|48000|0|0|nomon|swmeter|-|32bit
control device hw:0
configuring for 48000Hz, period = 1024 frames (21.3 ms), buffer = 2 periods
ALSA: final selected sample format for capture: 16bit little-endian
ALSA: use 2 periods for capture
ALSA: final selected sample format for playback: 16bit little-endian
ALSA: use 2 periods for playback
jackd watchdog: timeout - killing jackd
[gabo@machina ~]$
This is the output from QJackCtl:
00:12:07.126 Client deactivated.
00:12:07.130 JACK is being forced...
cannot read server event (Success)
cannot continue execution of the processing graph (Bad file descriptor)
zombified - calling shutdown handler
cannot send request type 7 to server
cannot read result for request type 7 from server (Broken pipe)
cannot send request type 7 to server
cannot read result for request type 7 from server (Broken pipe)
00:12:07.339 JACK was stopped with exit status=1.
I can hear my guitar and record with Audacity, but when jackd enter into the escenario everything blows up. I read that nowadays almost any sound card will work with QJackCtl with the default options. I play with the parameters and sometimes jack refuse to start. With the default options on i can make it run, but i get no sound of the racks or guitar effects processors neither the guitar tuners that use jack takes the sound from the guitar. My line input is in capture via alsamixer, but still no luck. Any clue on this? I'm skipping steps?
Thanks in advance.
iamgabo

Hi!
groups && cat /proc/asound/cards && cat ~/.asoundrc && cat '/etc/security/limits.d/audio.conf' && jackd -v
adm disk lp wheel http network video audio optical storage power users polkitd vboxusers wireshark kismet
0 [Live ]: EMU10K1X - Dell Sound Blaster Live!
Dell Sound Blaster Live! at 0xcc00 irq 17
#pcm.upmix71 {
#type upmix
#slave.pcm "surround71"
#delay 15
#channels 8
pcm.!default {
type hw
card 0
ctl.!default {
type hw
card 0
# convert alsa API over jack API
# use it with
# % aplay foo.wav
# use this as default
pcm.!default {
type plug
slave { pcm "jack" }
ctl.mixer0 {
type hw
card 1
# pcm type jack
pcm.jack {
type jack
playback_ports {
0 system:playback_1
1 system:playback_2
capture_ports {
0 system:capture_1
1 system:capture_2
cat: /etc/security/limits.d/audio.conf: No such file or directory
I have a file called 99-audio.conf
cat /etc/security/limits.d/99-audio.conf
@audio - rtprio 99
@audio - memlock unlimited
Also i've seen some guys changing this file too:
cat /etc/security/limits.conf
# /etc/security/limits.conf
#Each line describes a limit for a user in the form:
#<domain> <type> <item> <value>
#Where:
#<domain> can be:
# - an user name
# - a group name, with @group syntax
# - the wildcard *, for default entry
# - the wildcard %, can be also used with %group syntax,
# for maxlogin limit
#<type> can have the two values:
# - "soft" for enforcing the soft limits
# - "hard" for enforcing hard limits
#<item> can be one of the following:
# - core - limits the core file size (KB)
# - data - max data size (KB)
# - fsize - maximum filesize (KB)
# - memlock - max locked-in-memory address space (KB)
# - nofile - max number of open files
# - rss - max resident set size (KB)
# - stack - max stack size (KB)
# - cpu - max CPU time (MIN)
# - nproc - max number of processes
# - as - address space limit (KB)
# - maxlogins - max number of logins for this user
# - maxsyslogins - max number of logins on the system
# - priority - the priority to run user process with
# - locks - max number of file locks the user can hold
# - sigpending - max number of pending signals
# - msgqueue - max memory used by POSIX message queues (bytes)
# - nice - max nice priority allowed to raise to values: [-20, 19]
# - rtprio - max realtime priority
#<domain> <type> <item> <value>
#* soft core 0
#* hard rss 10000
#@student hard nproc 20
#@faculty soft nproc 20
#@faculty hard nproc 50
#ftp hard nproc 0
#@student - maxlogins 4
* - rtprio 0
* - nice 0
@audio - rtprio 65
@audio - nice -10
@audio - memlock unlimited
jackd 0.121.3
There are the snaps for QJackCtl
Also, checkout this stuff that i've recorded with audacity, only from the line and nothing else
http://ompldr.org/vZ3A2eg
Thanks!
Last edited by iamgabo (2012-12-15 02:21:08)

Unable to shutdown DB - Only ABORT works

Hi,
I just cloned a DB onto a Solaris 5 box with Oracle 7.3.4 from an AIX.
There were only a few transactions done by 1 user which probably had some sorting ; which used the temp tablespace probably.
When I tried to shutdown the DB - It wont ; I waited for 3 hours and tried an ABORT / Startup / Shutdown immediate. Still hangs for a long time. 2 hours and waiting.
Alert Log shows -- Waiting for smon to disable tx recovery.
I increased the "nice" priority for SMON thinking maybe it may help; but cant see any diff as of now.
I am thinking of leaving it for another few more hours to see if it would shutdown "immediate".
I read a few metalink notes : 1076161.6 / 61997.1 ; but the fet$ count sticks at a value and doesnt increase ( as per the document )
If this doesn't shut down in another 6 hours, will a constant "shu abort" cause any issues to the data ? I cant leave it for more than this time for it to shutdown gracefully.
Any Advice please ?
Thank you.

Abort for the shutdown won't create as such any severe issue(s) for the db with the only impact that the next time, database would be requiring recovery to be done and this can take from no time to very significant time even , depending on the number of transactions happened in the last life of the database. Before doing an abort, if you really have to do so, issue an "alter system checkpoint" . This would ensure that the buffers from the cache is flushed to the datafile and on next startup, number of buffers requiring recovery should be less.
That said, a quick search over Google, gave this thread for the same error. Check it out and hope it helps.
http://www.orafaq.com/maillist/oracle-l/2000/06/21/0140.htm
HTH
Aman....

WL server failed to response under load

Hi
We have a quite strange situation on my sight. Under load our WL 10.3.2 server failed to response. We are using RestEasy with HttpClient version 3.1 to coordinate with web service deployed as WAR.
What we have is a calculation process that run on 4 containers based on 4 physical machines and each of them send request to WL during calculation.
Each run we see a messages from HttpClient like this:
[THREAD1] INFO   I/O exception (org.apache.commons.httpclient.NoHttpResponseException) caught when processing request: The server OUR_SERVER_NAME failed to respond
[THREAD1] INFO   Retrying request
The HttpClient make several requests until get necessary data.
I want to understand why WL can refuse connections. I read about WL thread pool that process http request and understand that WL allocate separate thread to process web request and the numbers of threads is not bounded in default configuration. Also our server is configured Maximum Open Sockets: -1 which means that the number of open sockets is unlimited.
From this thread I'd want to understand where the issue is? Is it on WL side or it's a problem of our business logic? Can you guys help to deeper investigate the situation.
What should I check more in order to understand that our WL server is configured to work with as much requests as we want?

Thanks for a good explanation!
Linux server it's not in my competencies but what we have now is:
root    soft    nofile 3072
root    hard    nofile 65536
So the upper number is really big. As I understood it's a config for whole processes in operation system.
But I go further and find these numbers for our WL managed server.
cat /proc/23085/limits
Limit                     Soft Limit           Hard Limit           Units
Max cpu time              unlimited            unlimited            seconds
Max file size             unlimited            unlimited            bytes
Max data size             unlimited            unlimited            bytes
Max stack size            10485760             unlimited            bytes
Max core file size        0                    unlimited            bytes
Max resident set          unlimited            unlimited            bytes
Max processes             578455               578455               processes
Max open files            8192                 8192                 files
Max locked memory         32768                32768                bytes
Max address space         unlimited            unlimited            bytes
Max file locks            unlimited            unlimited            locks
Max pending signals       578455               578455               signals
Max msgqueue size         819200               819200               bytes
Max nice priority         0                    0
Max realtime priority     0                    0
Again it's only a config numbers. If continue moving in this direction I'd want to see the real numbers when the server is under load. So finding these numbers I would make an assumption that the issue is here. Don't you know is there a log file or history file where I can find a max open file descriptors for WL server?

How to disable the new Bluetooth Audio function?

After updating to OS 3.0 i have an annoying problem with my iPhone connected to a Kenwood car radio (via USB in the glove box):
1. Connect iPhone with car radio via USB
2. Turnin on the radio - now it starts playing songs from the iPhone
3. Now the iPhone connects via Bluetooth to the radio (for use of the handsfree set!)
4. The addressbook is downloaded by the radio via the Bluetooth connection
Till there it worked fine under OS 2.2.1 - i was able to listen to the iPod and to make/receive calls! But now there's step 5:
5. The Bluetooth Audio function is activated - and i can hear no more sound although the playback of the song is resumed!
There's a workaround for this issue: I can tap on the iPod-Icon on the iPhone which says that the iPhone is connected to an equipment. There i can tap on a bluetooth icon in the lower right corner in which i can select the device for audio output: Bluetooth or Dock.
This is really annoying (even more due to the bad qualitiy of the bluetooth audio), so where can i disable this new "feature"?!

I too am having this problem. It seems as though I also have to unplug and re-plugin my iPhone dock connector to make it switch to the USB output I need for my JVC KD-R800 receiver in my car. I can't seem to find a way to permanently disable A2DP functionality on either my iPhone or my Car's audio receiver.
We really do need some sort of option to either disable A2DP altogether or setup a "priority" list of items. Personally, I'd love to have the iPhone output in an order something like the following:
1st - Dock Connector (USB)
2nd - Bluetooth A2DP
3rd - Headphones / iPhone Speaker
Hopefully someone find out of a permanent workaround or solution soon. I just got this new receiver for my car and it messes everything up!

Problelm print from 13" macbook air OSX10.8.4 to hp x476dw

Priting issues from Macbook 13" to HP X476DW.
When printing, the printer will respond, the door opens on the printer, it thinkgs about it and you hear things moving, then the door closes. Queue empty, it thinks it did it's thing. Could be printing protocol issue where it expects one format over another, but unsure where to define this in osx.
Printer works fine from my windows computers on the network.
Printer works fine printing from Ipad devices using airprint.
I've used the reset printers option multiple times (to try different printer setups)
I used direct network access using mac standard installations.
I used airprint setup
I used wireless direct setup (nice features of this printer)
This is a brand new Macbook air with OSX 10.8.4.
in EVERY CASE the printer door will simply open, wait a while, and close. Nothing printed, not even a blank sheet of paper comes out. I can go to my windows PC and print right away no problem.
Side note, the scanner is working fine and since the printer does respond to the document (by beginning the process with opening the door) there is communitcation.
Any help on this? Has anyone else experienced this? It behaves like it does not know what to do with print data (as if it were sending in the wrong protocol, like PCL6 vs PS...)
Thanks in advance,
Marc

UPDATE: I enabled poscript error printing, I get this....
ERROR: undefined
OFFENDING COMMAND: obj
STACK: 4 , 0 ,
I hope this helps...

How to disable the new fb chatbox sidebar?

how to uninstall the new fb chatbox sidebar?

I too am having this problem. It seems as though I also have to unplug and re-plugin my iPhone dock connector to make it switch to the USB output I need for my JVC KD-R800 receiver in my car. I can't seem to find a way to permanently disable A2DP functionality on either my iPhone or my Car's audio receiver.
We really do need some sort of option to either disable A2DP altogether or setup a "priority" list of items. Personally, I'd love to have the iPhone output in an order something like the following:
1st - Dock Connector (USB)
2nd - Bluetooth A2DP
3rd - Headphones / iPhone Speaker
Hopefully someone find out of a permanent workaround or solution soon. I just got this new receiver for my car and it messes everything up!

WiFi and GPRS/3G Seamless switching???

Hi guys, i hope you will be able to offer some advice on a problem that i keep getting.
I am trying to setup my Nokia N97 (RM-505, v2.1) to use my bthomehub router when i am within range ie at home and then when i go out of range to switch SEAMLESSLY to 3G/GPRS. I have my WLAN scanning switched off and my homehub set to priority 1 and my GPRS connection setup as priority 2. works fine when im at home connects to the homenub no problem. But as soon as i go out of my homehubs range it doesn't then switch to use my priority 2 setting ie 3G/GPRS and constantly says "WLAN connection error" This is becoming very frustrating as at the moment i have my 3G/GPRS setup as priority 1 and homehub setup to priority 2 and setup too only use after confirmation. So if i want to use my homehub i have to start the connection manually which is very annoying! Please help as this is very annoying for a supposed flagship N-Series phone.
Thanks
Ryan

Alex, don't let anyone fool you. If your iPhone gives you a connection to a wireless connection and you actually see the wireless indicator on you home screen, you should be able to move data. You will not see the wireless indicator if you are trying to log in to a connection that requires a user name and password if you have not logged in. You will not have a connection until you do log in.
Sometimes there is a problem with how the iPhone connects to some routers. It will show you are connected, but when you look at your wireless settings in the phone, it shows just partial information that consist only of a strange invalid ip address. This happens with my phone all of the time when I am traveling, and even at home if my phone decides that it does not like the signal channel my router is on.

Setup NIC priority in OS X

Similar Messages

Maybe you are looking for