Simple WCS Mac filtering not functioning!

Hello forum,
We have just deployed WLC and WCS with couple of lightweight AP.
We decide to employ MAC filtering to restrict wireless client.
We noticed a SERIOUS problem, once we removed a mac address from the WCS and apply to controllers, Wireless client with that mac address are still able to access(ping,dhcp) the network even though its mac is removed from the currnt local mac filter after around 10mins???
Is there a know bug to this issue? or it requires some moment for the changes to take effect.

Hi all,
problems solved. session-timeout is causing the client to maintain the session after mac removal.
Cheers,
Kelvin

Similar Messages

MAC Filtering Not working

I have a Netgear CG3100D. When I try to set up MAC filtering (by loging into the Admin console), the list of trusted devices never seems to be accurate (i.e. things are missing off the list) and does not pull in the actual device names. Can anyone help ?

Hey blecp1,
Can you try a full default of the modem and see if it still happens?
Brodie

WAP321 MAC Filtering Not Working

Hello,
We have 6 x WAP321's setup via "Single Point Setup". We have enabled MAC Filtering and set to "Block all stations in list".
We have added one device into this list and confirmed this replicates around all the APs. However, it doesn't prevent the device from joining the wireless.
We have tried rebooting the APs and upgrading their firmware (1.0.5.3 ).
No difference.
Anyone else seen this or have any ideas?
Regards
Charlie

Hey blecp1,
Can you try a full default of the modem and see if it still happens?
Brodie

Several parts of my Mac are not functioning well

Greetings,
I own a Mac Pro (2008 model), which, while working perfectly, exhibits some issues. Having been annoyed by one of them today, I've finally managed to ask in this forum (english isn't my native language, so I hope to be clear enough in my phrases).
Here are the problems (I'm asking with the hope that someone knowing better than me can answer me):
1: the CD drive trays are hard to open.
The one on top always require me to use my finger to open (otherwise, the drawer stays closed and the drive finally give up and close the tray back).
The one on the bottom has a similar issue, that happens only the first time in a row (e.g it fails only the first time in a day). Here, it's not the drawer that gets stuck, it's the tray. For instance, I press the option-eject keys and I hear the bottom drive trying to open (and is stuck). I manually open the drawer, but the drive still does not open (and is "closed" after a couple of seconds). Then I can use option-eject again and it finally works.
I've tried "pushing" slightly some components in the hope to unstuck a possibly stuck piece, with no luck. I'm asking for what I can do next (I guess it's bad for the drive to try to force-open and then give up).
(just a note: I say "drawer" for the "outer door" and "tray" for the whole support that comes outside of the drive when it's ejected. I hope these are correct english terms).
2: one of my USB ports (front ones) isn't working, While I know it's common, on a Mac Pro, to have USB ports not working (I've read some pages on this forum), my symptoms are slightly different:
•First, only one of them isn't working (the one below the other), while on every post in this forum, it seems to have been both.
•Second, it seems only data aren't transmitted (power is sent just fine, as my iPhone gets charging but iTunes does not sees it (as does the whole computer)). In the forum, problems are related to USB that does not work at all (while not explicitly said, it appears no power is delivered either).
So I guess it's another kind of problem, but I don't know how to investigate here (is it a driver problem? Only affecting one port? Is it possible?).
3: My graphics card is a bad one (ATI HD 2600, known to be in the series of cards that are likely to fail). When in 10.4.11 (my preferred one), my computer will eventually hang when viewing movies (even short ones) using QuickTime (it appears to hang after some times of use, probably having something to do with temperature, but I'm not sure); the computer then does not update the display anymore, except for the mouse (why is the mouse still updated, by the way?). When not using QuickTime, or when using 10.5, the computer does not hang, but I see noise all around the screen (it's green noise, which seems to be "computed" (e.g happens more in black or grey areas, but also depends on the shape of the region; I try to be as most precise as I can, since screenshots aren't taking the default and I can't therefore post one). The second monitor does not show such problems.
•Will the problem get worse, theoretically?
•How long, based on my description, can I expect to use the current graphics card?
•Why does the problem occurs only on the first monitor (i.e the left connector when the card is in front of us)?
•May I use only the second output and be happy with that? (just giving up using two screens) This question is related to the previous (why only one output has the problem)
•Would watching my QuickTime movies only on the second monitor get rid of the problem (because the first output would not be stimulated that much)?
•Finally, I'm afraid of buying a graphics card to discover it may not be the problem (or the new one isn't working either). It seems these cards are rather expensive, and I can't afford to be wrong, buying a card that wouldn't solve the problem. Are my fears correct?
4: the fans are running almost always, except when I have to force-restart my computer (for instance, when the graphics card issue happens).
When the computer hangs and I restart it, the fans won't run at all (they are fully quiet). Then, I come to the login window and I log in. So the desktop appears, but only the boot partition shows up (my internal drive has 3 partitions). According to Activity Monitor, the other 2 are still being checked (since the hard restart). As long as both partitions are still being checked, the fans are quiet. When the 3rd one appears on the desktop (so all my partitions are mounted), the fans start making noise like they do all the rest of the day.
So I'm wondering:
•does it actually make sense that fans are sleeping as long as the computer hasn't mounted all the volumes?
•when is the behaviour normal: when the fans aren't running or when they are? (assuming the temperature isn't high, for example when the computer has just started).
5: it has happened to me twice since the beginning of this year: my Mac Pro turns itself on in the middle of the night (and it makes me waking up as well). The console says it's an USB peripheral that made the computer waking up (but since I was sleeping and I have no animal in my room, it sounds strange to me).
Would it be possible that an USB cable, because of changing temperature, is moving a bit and makes the computer waking up? What else can cause that?
6: when I plug a computer in the 2nd ethernet device (the 1st one being connected to the Internet), I can't seem to be able to connect both to the other computer and to the Internet (I can only connect to the one whose position in "System Preferences" ("Network" then "Ports") is above the other; the other one being always not reachable (either web pages can't be loaded, or Finder's connect to window stays at "Searching for host…")). If it's not possible, what's the purpose of 2 ethernet ports?
Sorry for the long message, but I'm always curious (and the message would have been shorter if english was my primary language).
P.S: I used to know computers fairly well in Mac OS 9 days, but Mac OS X has complicated things (and hidden a bunch of them through undocumented error codes and behaviours/logs), that I'm being more curious than I used to be.
Thanks in advance if you can answer some or all of my questions.

Smokerz wrote:
I have a 2008 Mac Pro. Don't know where to start addressing your situation but here goes:
1) go to Apple/support and make sure your SMC version is up to date
Already done
2) at the same place search for smc reset or power manager reset
I did that several months ago as well.
3) two ethernets connected. Example one ethernet port for connector to router which then connects to cable modem to get to the internet. The other ethernet connect to say an HP laserjet will not be shown on the local network if the Mac Pro is slept or shutdown. So its either one or the other, think of it that way.
So, not possible to have the 2 ethernets for 2 different networks?
(e.g one for the Internet and the other for connecting another computer)
4) you don't make it clear about the optical eject/retract sticking. If you installed some your self then you should remove the face plate because 99.9% don't fit properly(they don't clear).
I didn't install it myself, it came so. Anyway, I think you're right with the end of your sentence (it doesn't fit properly). However, both trays have different symptoms (one is blocking because of the front door and the other is blocking because of the internal tray), so I'm not sure how to solve that (I could keep the door open for the first one, but what about the 2nd one?).
Please tell me how I can be more clear about this issue.
5) the USB , try a good power usb hub, the smc reset may help this point of usb failure. The hub will definitely help, I use a very small CYBER POWER and have never a problem. Other vendor hubs yes but not this one.
I guess I've not be clear on that as well?
The power is the working part of that USB port. For example, if I put my external Hard Disk (powered only from USB), the light comes up and the drive spins up, yet the mount process does not happen (the disk isn't read and isn't detected).
So, if the port fails to send data without a hub (i.e directly) how would a hub address the issue?
(and, by the way, I've actually a hub, but things get worse when I use it, even with a single device; e.g my iPhone, if connected to it, disconnects at various time).
6) you mention running in 10.4.11 that 2008 Mac Pro is unsupported for Tiger.
Really? That's a shame, 10.5 is unusable to me (unbelievable bad changes in the OS). Well, 10.4 works fine there anyway.
You mention 10.5 have you updated to 10.5.8 and all system updaters. The 2008 Mac Pro runs very reliably using 10.6 or higher.
I've 3 partitions:
•One with 10.4.11
•One with 10.5.8
•One with 10.6.x (I do the update more rarely on this one because I usually don't use it)
As I said earlier, 10.4 is almost required for me. Only for watching videos I restart to 10.5 (and make the update there when available). But I can't afford to live with 10.5. 10.6 is even worse.
The fan situation would be a non issue. I just did a clean install of my son's 2006 Mac Pro and while it was running in 10.5.8 the fan noise bothered me but once 10.6+ went in the fan noise was a non issue.
Are you implying that 10.6 made the noise reduce?
You could replace that 2600 with a Nvidia 8800GT, if you can find one but do not buy the one created for the 2006 Mac Pro, it will not work. Also the GT 120 or Radeon 5770 or 5870 will work but unsupported. That means if you ever do a clean install your install disks will not have the drivers for those radeon cards but the OS will install. Then once you update Snow Leopard the drivers will be installed. Snow Leopard 10.6.4 is minimum.
I'd prefer to avoid using 10.6.4, indeed.
Thank you

Column header filtering not functioning for external lists

I have a problem with column header filtering on external lists, specific for columns of Number and Date types.
When the site's regional settings are in English (United States) filtering works fine, but if I choose any other regional setting with different number formatting (ie Dutch) then filtering on these columns gives no results.
When clicking on the column header filter dropdown, the numbers to filter on are displayed with thousands seperators where the numbers in the views are not formatted as seen in attached screenshot.
Filtering on custom sharepoint list with these regional settings is working fine, it is just on external lists, on number and date fields and regional setting is not English.
I have tried all different kind of regional settings on the client and the server, but no results.
Anybody has a clue?
Clicking on the column header shows all available filter values (with thousand seperator). Selecting one value gives no results:
No results after selecting a filter value

Hi,
According to your post, my understanding is that you had an issue about column filter in external list.
We can use the SharePoint Manager to change the column type to “single line of text”, then you would filter column in the external list.
There is a similar thread for your reference:
http://social.technet.microsoft.com/Forums/en-US/fe67d581-6e7b-4770-b296-8ec0f9b5b769/not-able-to-filter-or-sort-by-list-column-headers-for-external-data-fields-ideas?forum=sharepointgeneralprevious
Thanks,
Jason
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Jason Guo
TechNet Community Support

AP1242AG WPA and MAC Filtering problem

Hello,
Presently I managed some AP1242AG in ofiice area
I need implement WPA and MAC filtering.
I found what :
In IOS 12.2(13)JA branch IOS and before, MAC authentication was supported
in conjunction with WPA.
In 12.2(15)JA and above, configuring MAC authentication with WPA does not
work. MAC Authentication passes everyone through.
I can't found IOS 12.2(13) in Cisco site.
Can anybody help me and give link to download 12.2(13)JA ?
Thanks.

Also when I acivete MAC filterring
access-list 700 deny   0024.d7ed.2204   0000.0000.0000
access-list 700 deny   0000.0000.0000   ffff.ffff.ffff
dot11 association mac-list 700
dot11 ssid zero!v
   vlan 390
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
   wpa-psk ascii 7 14531708030A2E1A3108212127015644
The WPA is working but MAC filtering not reject
IOS Ver.
Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(11)JA1, RELEASE SOFTWARE (fc2)

Airport Express WiFi network MAC address filtering not working

I have an Airport Express WiFi network which I bought and installed new in 2011. Initially I enabled MAC address access control and populated a list. It was working perfectly, I know, because a niece visiting tried to connect her iPhone and could not until I added its MAC address to the allowed list. Now however, anyone can connect without being added to the list. I think I read somewhere that a recent firmware update permanently disabled MAC filtering in Airport Express, even when it was previously working? Can anyone enlighten me about what's going on here?

In a sense those are/were/should operate as two separate functions, which they did before recently.
They do operate as two separate functions.....but it all depends on how you have the default rule setup in Timed Access.
If the default rule in Timed Access is set to No Access.......then a wireless device cannot connect....even it has the password for the network.....unless it has been setup on the list of allowed devices in Timed Access.
I have checked this 3 times this evening to verify. It works as it always has, and as expected.
If the default rule in Timed Access is set to Unlimited, then any device can connect to the network if it has the password. Devices that are listed or specified in Timed Access will be allowed to connect at the specific times that have been set up for each device.
So, if you want to use the more traditional MAC Access Control settings, the default rule has to be set to No Access and then you must set up a rule for each device that you want to allow to connect to the network. Only devices on the Timed Access list will be allowed to connect to the network. Other devices will not be able to connect to the network....even if they have the correct password.
If a recent firmware update has changed things from what they have always been.....then I am not affected....and I should be if I am using the same firmware as others.

Bought a Mac Mini. at 18 day's old it started to lock up and not function. Took it in and they wiped and reinstalled it. Well at 24 day's old it's been sitting in the box not being used. First and last Mac for me. But can I get something for the junk?

I have pulled it out of the box and put 2 Mac approved mem sticks in it to boost it to 8 Gigs mem and it still locks up and freazes.. So many people told me Mac was the way to go... 1500 dollers could have bought me a great pc laptop. Now I have a wirless mouse keyboard and a mac mini (aka Brick) that allowed me to donate money to a cause that is helping buildings and companies out side of the US. While I have junk.. It's still under warranty and I reinstalled the os after the new mem sticks. Again.. locks up and does nothing. What can I do with this? Toss it in the trash? Any info on what I might do with it.. Please help!

It would be most helpful if you updated your system information:
Please reconcile the following
at 18 day's old it started to lock up and not function. Took it in and they wiped and reinstalled it. Well at 24 day's old it's been sitting in the box not being used.
... I reinstalled the os after the new mem sticks.
If your Mini is anything less than six months old it would be running Lion, not 10.6.1, nor would it have been necessary to "reinstall the OS". Any help that anyone can provide is predicated on your system configuration so it's important.
If you are running Lion then boot your Mini while holding the D key. This will load Apple Hardware Test which will enable you to test your memory. "Mac approved" memory is sort of vague, and even memory that is allegedly designed to meet your Mini's specification may fail. There few reputable memory vendors.
"Apple installed" memory is more meaningful, and indicates Apple has tested it and guarantees its function. Otherwise all bets are off with a claim of "Mac approved". You will have to verify that yourself with Apple Hardware Test.
If your Mini was running, or ever ran OS 10.6.1 for that matter, it is close to three years old.
You must clear up these uncertainties before anyone can help.

E1200 - Ports not working and mac filtering problem

If there was a way to give negative stars to this router, I would. As it is, the minimum rating I can give this product is one star, and that's one star too many.
I was upgrading from the WRT54G, which is an ugly thing to look at, but a reliable workhorse nonetheless. I turned that in to a downstream switch in my comms hub.
On the E1200, I flashed the latest firmware, used different Cat5 cables, and different laptops before committing to hating this product.
The first time I reached out to Amazon, the Amazon rep gave me a Cisco number to call. Turns out, that's some shady mortgage refinance hotline. Try it for yourself! 1-800-666-1771.
Now, the rant -
1. Two out of four wired LAN ports don't work: What can be the fix for this?! The activity lights on ports 3 and 4 blink and suggest data transfer is taking place, but the wired laptop simply can't acquire an IP address and access the internet. Same result when I connect my Panasonic Blu-Ray player to ports 3 and 4. None of the Viera Cast features load.
2. MAC filtering unreliable: The wireless routing works somewhat reliably, if and only if, one settles for the most basic security. If I only choose a password and WPA2 protocol, things work fine. If I add another layer of security (in my case, enabling MAC filtering and only PERMITTING gateway to listed MAC IDs), things break down. As soon as I disable MAC filtering, wireless access to authenticated clients is restored.
3. Cisco customer service: The censored world we live in, compels me to criticize politely. TERRIBLE. Cisco website is unintuitive, and frustrating. There's no easy way to register your purchased product. The Cisco "registration" is intentionally misleading and deceptive. For all intents and purposes, it's just an information gathering tool for Cisco. Don't bother registering there, unless you love the idea of storing your personal information on their servers. Their phone-based customer service is apathetic and uninterested. My rep was so distrusting of my intelligence and motor control, that he simply wouldn't believe that I had selected "PERMIT" and not "PREVENT" as the option under MAC filtering. After he asked me the same question for the fourth time, I raised my voice, and he gave up the idea of checking for the fifth time.
However, this review is a tale of two companies. I reached out to Amazon again. This time, I got a rockstar in the shape of Leanne C! She was incredibly helpful, and understanding. What's more, she set up my return without any hassle and this Cisco dud is on its way back. I'm a big fan of Leanne's and my confidence in Amazon is restored.
I'm sure that i received a lemon. I've never had problems with Linksys products. Maybe others' experience is different from mine.

In your case as port numbers 1 and 2 does not work, what you could have done a loop back test. To perform a loop back test you need to take an ethernet cable, connect one end of that cable to internet port and the other end to the non-working port on the router. If you get the led to glow on both internet and the respective ethernet port that indicates that the port is working fine.
It could also be a sychronization issue between the above mentioned lan ports and the lan card of your computer. As a part of trouble shooting you can try to reduce the card speed of your lan card. Following are the steps to reduce the speed of your lan card.
START--> right-click My Network Places and click Properties
right-click on the device manager and click properties
Click on the CONFIGURE button
Select the ADVANCED tab and in the box under the header property select "speed and duplex" and change the value on the right to 10 mbps half duplex. A restart would be recommended after performing these steps.
In the second half you said that after enabling the mac filter option the internet breaks down. Here, do you mean to say that the computer
gets disconnected from the wireless network or it stays connected with a valid IP address but without an internet connection.
Well, it is an unusual issue however you could have reset and reconfigure the router as you got the latest firmware upgraded on it.
Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.

Firewire does not function after uninstalling macfuse and an out of date version of NTFS32 and then installed latest version of Tuxera NTFS for Mac.

I purchased a 3TB HDD (WD USB 3.0 $100) to replace the 2TB Seagate for a new Time Machine HDD. The 2B was full and backups were deleting older files. The 3TB was formatted NTFS and I want to "recover" the included SW before I reformatted the HDD for the iMac. I discovered that MacFuse was out of date and unsupported and my NTFS-32 was also out of date so I uninstalled both and then installed the most recent version of Tuxera NTFS for Mac. I rebooted and discovered that the FW800 port was unresponsive. Below is the EtreCheck report:
Problem description:
Firewire does not function after uninstalling macfuse and an out of date version of NTFS32 and then installed Tuxera NTFS for Mac.
EtreCheck version: 2.0.8 (95)
Report generated October 30, 2014 7:11:17 PM EDT
Hardware Information: ℹ️
iMac (24-inch Mid 2007) (Verified)
iMac - model: iMac7,1
1 2.8 GHz Intel Core 2 Duo CPU: 2-core
4 GB RAM
BANK 0/DIMM0
2 GB DDR2 SDRAM 667 MHz ok
BANK 1/DIMM1
2 GB DDR2 SDRAM 667 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
ATI,RadeonHD2600 - VRAM: 256 MB
iMac 1920 x 1200
System Software: ℹ️
OS X 10.8.5 (12F45) - Uptime: 0:17:34
Disk Information: ℹ️
WDC WD5000AAKS-40TMA0 disk0 : (500.11 GB)
S.M.A.R.T. Status: Verified
disk0s1 (disk0s1) <not mounted> : 210 MB
ML 10.8 (disk0s2) / [Startup]: 499.25 GB (20.92 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
Apple Inc. Built-in iSight
Apple Computer, Inc. IR Receiver
Logitech USB Receiver
Apple Inc. Bluetooth USB Host Controller
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Applications/Hardware Monitor ƒ/HardwareMonitor.app
[loaded] com.bresink.driver.BRESINKx86Monitoring (7.0) Support
/Applications/Parallels Desktop.app
[not loaded] com.parallels.kext.hidhook (8.0 18615.948847) Support
[not loaded] com.parallels.kext.hypervisor (8.0 18615.948847) Support
[not loaded] com.parallels.kext.netbridge (8.0 18615.948847) Support
[not loaded] com.parallels.kext.usbconnect (8.0 18615.948847) Support
[not loaded] com.parallels.kext.vnic (8.0 18615.948847) Support
/Applications/Toast Titanium v11.1/Spin Doctor.app
[not loaded] com.hzsystems.terminus.driver (4) Support
/Applications/Toast Titanium/Toast Titanium v11.1 (1072).app
[not loaded] com.roxio.TDIXController (2.0) Support
/Library/Application Support/Symantec/AntiVirus
[loaded] com.symantec.kext.SymAPComm (12.2f1 - SDK 10.6) Support
/System/Library/Extensions
[loaded] com.Logitech.Control Center.HID Driver (3.9.0 - SDK 10.6) Support
[loaded] com.eltima.ElmediaPlayer.kext (1.58 - SDK 10.4) Support
[not loaded] com.hzsystems.driver.CDSDAudioCaptureSupport (1.5) Support
[not loaded] com.increw.kext.speedit (0.32) Support
[loaded] com.logitech.manager.kernel.driver (4.10.0 - SDK 10.8) Support
[not loaded] com.olympus.CamBlockCommandsDevice (2.0.0) Support
[not loaded] com.olympus.CamBlockCommandsDeviceUP (2.0.0) Support
[not loaded] com.palm.ClassicNotSeizeDriver (3.2.1) Support
[not loaded] com.roxio.BluRaySupport (1.1.6) Support
[not loaded] com.seagate.driver.PowSecDriverCore (5.1.1) Support
[loaded] com.symantec.kext.internetSecurity (5.2f1 - SDK 10.6) Support
[loaded] com.symantec.kext.ips (3.5f1 - SDK 10.6) Support
[loaded] com.symantec.kext.ndcengine (1.0f1 - SDK 10.6) Support
[loaded] com.taoeffect.ispy.kext (2.0.2 - SDK 10.2) Support
/System/Library/Extensions/OlympusDSCDriver.kext/Contents/PlugIns
[not loaded] com.olympus.CamFWSerialBusProtocolTransport (2.0.0) Support
[not loaded] com.olympus.CamUSBMassStorageClass (2.0.0) Support
/System/Library/Extensions/Seagate Storage Driver.kext/Contents/PlugIns
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.1.1) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.1.1) Support
[not loaded] com.seagate.driver.SeagateDriveIcons (5.1.1) Support
/Users/[redacted]/Downloads/LCC Installer.app
[not loaded] com.Logitech.Unifying.HID Driver (1.3.1 - SDK 10.8) Support
Startup Items: ℹ️
TuxeraNTFSUnmountHelper: Path: /Library/StartupItems/TuxeraNTFSUnmountHelper
Startup items are obsolete and will not work in future versions of OS X
Launch Agents: ℹ️
[running] com.canon.MFManager.plist Support
[not loaded] com.cooliris.SetLaunchArch.plist Support
[loaded] com.google.keystone.agent.plist Support
[running] com.Logitech.Control Center.Daemon.plist Support
[running] com.logitech.manager.daemon.plist Support
[running] com.micromat.TechToolProAgent.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
[running] com.seagate.SeagateStorageGauge.plist Support
[running] com.symantec.uiagent.application.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[running] com.cleverfiles.cfbackd.plist Support
[running] com.eltima.ElmediaPlayer.daemon.plist Support
[loaded] com.embraceware.awaken.plist Support
[loaded] com.google.keystone.daemon.plist Support
[loaded] com.macpaw.CleanMyMac2.Agent.plist Support
[running] com.micromat.TechToolProDaemon.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[loaded] com.prosofteng.DriveGenius.locum.plist Support
[running] com.smithmicro.schedulerdaemon.plist Support
[loaded] com.symantec.liveupdate.daemon.ondemand.plist Support
[failed] com.symantec.liveupdate.daemon.plist Support
[not loaded] com.symantec.sep.migratesettings.plist Support
[running] com.symantec.sharedsettings.plist Support
[running] com.symantec.symdaemon.plist Support
[running] com.taoeffect.ispyd.plist Support
[running] com.wdc.drivemanagerservice.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist Support
[loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist Support
[running] com.prosofteng.DGMonitor.plist Support
[running] com.smithmicro.cleaning.schedulermailer.plist Support
[running] com.taoeffect.EspionageHelper.plist Support
User Login Items: ℹ️
Speedy Mac Application (/Applications/Speedy Mac/Speedy Mac.app)
AwakenHelper Application (/Users/[redacted]/Library/Application Support/Awaken/AwakenHelper.app)
GetBackupAgent Application (/Users/[redacted]/Library/Application Support/BeLight Software/Get Backup 2/GetBackupAgent.app)
WDDriveUtilityHelper Application (/Users/[redacted]/Downloads/WD/WD Drive Utilities.app/Contents/Resources/WDDriveUtilityHelper.app)
ClustersHelper Application (/Library/PreferencePanes/Clusters.prefPane/Contents/Resources/ClustersHelper.a pp)
RealPlayer Downloader Agent Application (/Users/[redacted]/Library/Application Support/RealNetworks/RealPlayer Downloader Agent.app)
SAVDiskMountNotify UNKNOWN (missing value)
ScanNotification UNKNOWN (missing value)
Launch Nikon Message Center 2 Application (/Applications/Nikon Software/Nikon Message Center 2/Nikon Message Center 2.app/Contents/SharedSupport/Launch Nikon Message Center 2.app)
Internet Plug-ins: ℹ️
EPPEX Plugin: Version: 10.0 Support
Flash Player: Version: 15.0.0.189 - SDK 10.6 Support
AdobePDFViewer: Version: 9.4.6 Support
Unity Web Player: Version: UnityPlayer version 3.5.3f3 - SDK 10.6 Support
NPVirtools: Version: 4.0 Support
iPhotoPhotocast: Version: 7.0 - SDK 10.8
RealPlayer Plugin: Version: (null) Support
DirectorShockwave: Version: 11.6.8r638 Support
QuickTime Plugin: Version: 7.7.1
FlashPlayer-10.6: Version: 15.0.0.189 - SDK 10.6 Support
GarminGpsControl: Version: 2.9.3.0 Release Support
ToontownBundleManager: Version: (null) Support
CANONiMAGEGATEWAYDL: Version: 3.1.0.2 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
OVSHelper: Version: 1.0 Support
CoolirisWebKitPlugin: Version: (null) Support
Google Earth Web Plug-in: Version: 6.1 Support
Flip4Mac WMV Plugin: Version: 3.2.0.16   - SDK 10.8 Support
SharePointBrowserPlugin: Version: 14.4.4 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 7 Update 67 Check version
OfficeLiveBrowserPlugin: Version: 12.3.6 Support
User Internet Plug-ins: ℹ️
BrowserPlus_2.9.2: Version: 2.9.2 Support
Picasa: Version: 1.0 Support
Safari Extensions: ℹ️
DivX Plus Web Player HTML5 <video>
Open in Internet Explorer
DivX HiQ
Aimersoft Video Converter
3rd Party Preference Panes: ℹ️
BrowserPlus Support
Clusters Support
Déjà Vu Support
Flash Player Support
Flip4Mac WMV Support
Java Support
Logitech Control Center Support
Logi Preference Manager Support
MenuMeters Support
Perian Support
Symantec QuickMenu Support
TechTool Protection Support
Tuxera NTFS Support
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Destinations:
iMac TimeMachine [Local]
Total size: 2 TB
Total number of backups: 80
Oldest backup: 2011-09-18 05:21:33 +0000
Last backup: 2014-10-05 20:18:55 +0000
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 0 B X 3)
/sbin excluded from backup!
/usr excluded from backup!
/System excluded from backup!
/bin excluded from backup!
/private excluded from backup!
/Library excluded from backup!
/Applications excluded from backup!
Top Processes by CPU: ℹ️
      2% WindowServer
      0% Speedy
      0% SystemUIServer
      0% RealPlayer Downloader Agent
      0% ps
Top Processes by Memory: ℹ️
288 MB SymDaemon
150 MB Speedy
137 MB Safari
82 MB WebProcess
82 MB coreservicesd
Virtual Memory Information: ℹ️
2.17 GB Free RAM
1.46 GB Active RAM
148 MB Inactive RAM
518 MB Wired RAM
388 MB Page-ins
0 B Page-outs
I hope someone has some ideas! TIA.

Do you have another cable you can test with? Do you have access to another computer with Firewire you can test with?
FireWire Device not Working
FireWire/USB - Quick Assist

"Finder" does not function after installing Leopard on Mac G5

After successfully installing Leopard on my (new) MacBook Pro and on my (old:2003) iMac PowerMac 6,1 I tried installing Leopard on my 2005 iMac G5.
The installation seemed successful, but after restarting the computer I was asked to choose the wireless network from a list. This was not possible. I do not use the Airport on this computer so tried to press "cancel". Could not do this and got the turning rainbow circle which never stopped.
*The Finder does not function and cannot be restarted. This seems to be the main problem.
I cannot log off or shut down and have to use the powerbutton to shut down.
When starting up I do not get the Startup sound. Do get login and can login. But, all my desktop buttons have disappeared and I immediately get a notice that OS X shut down unexpectedly, asking me to cancel or send a report. Neither of these options are possible and the turning rainbow reappears. It's driving me crazy!
I can sometimes open programs but no longer "system preferences".
Is there anybody out there who can help me??
I am especially frustrated since the other two installations on an older and on a newer Mac went well. I use the exact same programs on all three computers.
HELP!

After successfully installing Leopard on my (new) MacBook Pro and on my (old:2003) iMac PowerMac 6,1 I tried installing Leopard on my 2005 iMac G5.
The installation seemed successful, but after restarting the computer I was asked to choose the wireless network from a list. This was not possible. I do not use the Airport on this computer so tried to press "cancel". Could not do this and got the turning rainbow circle which never stopped.
*The Finder does not function and cannot be restarted. This seems to be the main problem.
I cannot log off or shut down and have to use the powerbutton to shut down.
When starting up I do not get the Startup sound. Do get login and can login. But, all my desktop buttons have disappeared and I immediately get a notice that OS X shut down unexpectedly, asking me to cancel or send a report. Neither of these options are possible and the turning rainbow reappears. It's driving me crazy!
I can sometimes open programs but no longer "system preferences".
Is there anybody out there who can help me??
I am especially frustrated since the other two installations on an older and on a newer Mac went well. I use the exact same programs on all three computers.
HELP!

I have upgraded my MAC OS to 10.6.8. FCP 5.0 still runs great, but Soundtrack Pro 1.01 opens, but operates at a glacial pace. It does not functionally operate. What can be done to remedy this?

I have upgraded my MAC OS to 10.6.8.
Final Cut Pro 5.0 still runs great, but Soundtrack Pro 1.01 opens, but operates at a glacial pace. It does not functionally operate.
What can be done to remedy this?

Depending on the configuration of the computer hardware and software
you may need to consider upgrade the RAM by installing more capacity.
Also, in the same vane, choose to consider upgrade the hard drive to
one of faster transfer, such as SSD, hybrid, or fusion; if not already at
least 7200-RPM and not too full of saved content.
Since no information is given about the model build configuration of Mac
there may be other suggestions to make it work better. Usually an OS X
upgrade requires one to look at the hardware resources available to it.
The OS X works best with more memory: new higher capacity chips.
This may be possible, and they should be high quality from reputable
vender who has tested them on Apple in OS X, such as OWC or Crucial.
Good luck & happy computing!

MAC Filtering via Radius not working

Hi Folks,
I'm having problems with MAC filtering via RADIUS. I have a combination of a local database on the controllers and remote MAC addresses provisioned on a Cisco ACS. My problem is that even when I've set the controllers to use Radius and I've configured the order to be local and then radius the controllers never sent an auth request to the Radius servers. I know that Radius can work because I have another WLAN (the guest WLAN) on the same hardware that is configured to authenticate first against the local database and then against Radius and this is working fine.
(WiSM-slot9-1) >debug aaa all enable
*Oct 09 08:01:44.518:       AVP[14] Called-Station-Id........................X.X.X.X (9 bytes)
*Oct 09 08:03:21.677: Unable to find requested user entry for 6cc26b5990e5
*Oct 09 08:03:21.677: ReProcessAuthentication previous proto 8, next proto 40000001
*Oct 09 08:03:21.677: AuthenticationRequest: 0x18cc933c
*Oct 09 08:03:21.677:   Callback.....................................0x10112bc4
*Oct 09 08:03:21.677:   protocolType.................................0x40000001
*Oct 09 08:03:21.677:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.677:   Packet contains 14 AVPs (not shown)
*Oct 09 08:03:21.678: 6c:c2:6b:59:90:e5 Returning AAA Error 'No Server' (-7) for mobile 6c:c2:6b:59:90:e5
*Oct 09 08:03:21.678: AuthorizationResponse: 0x38f71958
*Oct 09 08:03:21.678:   structureSize................................32
*Oct 09 08:03:21.678:   resultCode...................................-7
*Oct 09 08:03:21.678:   protocolUsed.................................0xffffffff
*Oct 09 08:03:21.678:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.678:   Packet contains 0 AVPs:
*Oct 09 08:03:21.680: Looking up local blacklist 98d6bbde785f
*Oct 09 08:03:21.754: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.754: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.778: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.846: Unable to find requested user entry for 6cc26b5990e5
*Oct 09 08:03:21.847: ReProcessAuthentication previous proto 8, next proto 40000001
*Oct 09 08:03:21.847: AuthenticationRequest: 0x18c6dcc4
*Oct 09 08:03:21.847:   Callback.....................................0x10112bc4
*Oct 09 08:03:21.847:   protocolType.................................0x40000001
*Oct 09 08:03:21.847:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.847:   Packet contains 14 AVPs (not shown)
*Oct 09 08:03:21.847: 6c:c2:6b:59:90:e5 Returning AAA Error 'No Server' (-7) for mobile 6c:c2:6b:59:90:e5
*Oct 09 08:03:21.847: AuthorizationResponse: 0x38f71958
*Oct 09 08:03:21.847:   structureSize................................32
*Oct 09 08:03:21.847:   resultCode...................................-7
*Oct 09 08:03:21.847:   protocolUsed.................................0xffffffff
*Oct 09 08:03:21.847:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.848:   Packet contains 0 AVPs:
I'm assuming thaty the line - Returning AAA Error 'No Server' - is significant but I have configured the Radius servers correctly but a packet trace shows no auth requests whatsoever from the controllers. Has anyone seen this? Anything I should be looking at?
Thanks in advance,
Shane.

The bug I ran into was CSCta53985 on the WLCs. I upgraded to 7.0 and it fixed it. The fix is available in 6.0.188. Depending on your WLC hardware, I would go to at least 7.0.116 for newer AP support, and CleanAir support.

Mac mail search function is not working. Any search term returns all records.

Mac mail search function is not working. Any search term returns all records.

hi eric. many thanks.
i will have to read these links closer but what i meant to say is that the hard drive space that was being taken up seemed like it suddenly jumped way up because i had just gotten through a process in the last month where i am storing all my My Documents data on my Mac Pro. i am doing this in order to decide whether i should just keep it ALL on my Mac Pro and use ChronoSync to sync /some/ of it to my MBP.
so if i look in the Documents folder on my Mac Pro i have a ton of folders that i have created with a ton of data. if i look in the Documents folder on my MBP there are NO folders that have data in them that i created. there are other folders such as folders that various software created but what i mean to point out is that there was a LOT of available space on my HD until recently.
i am wondering if there is some way that running the Mail re-index (it then ran some kind of "Importing" routine) or by syncing my Photostream to the MBP caused a huge jump in data on this drive. if it is the photostream sync i can just take this off or see if it will sync more selectively. if it is something to do with mac mail jumping in size i am not sure why this would happen or what to do about it.
does that question make sense?
i mean, before i did these two operations my recollection is that i would have had 130 GB on the hard drive (really just guessing here) and now there is like 218 GB on the hard drive and i don't know where all this came from...

I purchused a Mac 10.9.4. The screen saver is not functioning, any idea why?

I purchased a Mac 10.9.4. The screen saver is not functioning, any idea why? Thanks.

A new Mac comes with 90 days of free tech support from AppleCare.
AppleCare: 1-800-275-2273
Best.

Simple WCS Mac filtering not functioning!

Similar Messages

Maybe you are looking for