SNMP polling for 5108 Chassis

I'm attempting to set up SNMP statistics polling for the 5108 Chassis with 4 half width blade servers. I can get SNMP data from the 6120 Fabric Extender just fine such as IFs and such, but I don't see any OIDs corrisponding to the chassis.
Is there a separate host I should poll for the chassis, or perhaps a different community name?
I'm specifically looking to monitor power draw from the four Chassis PSUs, as well as the two FE PSUs.
root@sj-mon:~# snmpwalk -v 2c -c public ucs1 .1.3.6.1.4.1.9.9.117.1.1.1
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.1.470 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.1.471 = INTEGER: 2
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.2.470 = STRING: "CentiAmps @ 12V"
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.2.471 = STRING: "CentiAmps @ 12V"
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.3.470 = INTEGER: 4538
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.3.471 = INTEGER: 4538
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.4.470 = INTEGER: 29
SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.4.471 = INTEGER: 29
Here is all I've been able to pull for the FE PSUs, and the 4538 value doesn't seem to have any correlation to what's being shown in the UCS Manager under Statistics.
Thanks!

There are no stats for the chassis.
You can only snmpget stats for the "NXOS" part of the Fabric Interconnect.
You can get snmptraps for all of UCS (go a google for UCS-MIB, and there's a doc explaining this on cisco.com - do a google for site:cisco.com ucs documentation roadmap).
At the end of the year I believe a full MIB will be available to do what you want.
If you want stats, use the XMLAPI.
Cheers
Steve

Similar Messages

SNMP OID for 5108 Chassis input and output Watts?

Anybody know these?
Craig

Craig,
OID for cucsEquipmentChassisStatsTable -- 1.3.6.1.4.1.9.9.719.1.15.10
UCS MIBs are available here
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html
HTH
Padma

Wrong SNMP values for ciscoEnvMonSupplyStatus

Hello everyone,
we are facing the following issue: the SNMP poll is showing wrong values for ciscoEnvMonSupplyStatus when at the same time the "show env all" shows that there is nothing wrong with the power supplies.
Here is the example:
ciscoEnvMonSupplyStatusDescr.1057   Sw1, PS1 Faulty, RPS NotExist                  OctetString                  192.168.49.28:161
ciscoEnvMonSupplyStatusDescr.1058   Sw1, PS2 Faulty, RPS NotExist                  OctetString                  192.168.49.28:161
ciscoEnvMonSupplyState.1057                                     notFunctioning (6)                        Integer                          192.168.49.28:161
ciscoEnvMonSupplyState.1058                                     notFunctioning (6)                        Integer                          192.168.49.28:161
------------------ show env all ------------------
FAN 1 is OK
FAN 2 is OK
FAN PS-1 is OK
FAN PS-2 is OK
SYSTEM TEMPERATURE is OK
System Temperature Value: 31 Degree Celsius
System Temperature State: GREEN
Yellow Threshold : 46 Degree Celsius
Red Threshold    : 60 Degree Celsius
SW PID                 Serial#     Status           Sys Pwr PoE Pwr Watts
1A C3KX-PWR-350WAC     AZS161803GQ OK              Good     Good     350/0
1B C3KX-PWR-350WAC     AZS161803GT OK              Good     Good     350/0
I have seen that this is a more or less a known issue and there are plenty of bugs for it, but exactly for our hardware and IOS (C3560E Software (C3560E-IPBASEK9-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)) I cannot find any exact information.
Please, advice if we are hitting some known bug which I cannot locate.
Thanks,
Vesselin
SW Status          RPS Name          RPS Serial# RPS Port#
1   Not Present     <>

Hi ,
I have issue while generating alerts for the CISO nexus device.
snmp laert tool: Solarwinds error : The OID is not supported,
Can anyone tell me the OID for the CISCO nexus 2k, 5K devices.
I am trying to generate the Temp alert.
THANKS

Snmp alerts for CPU utilization

Hi,
I want to enable snmp alerts on l2 and l3 switches to monitor CPU utilization.
I have Opmanager which is acting as SNMP server.
I have switches L2 and L3 which are running IOS 12.0, 12.1, 12.2
Do all these IOS versions support SNMP alerts?
And also I want to know the commands to be configured on switches for this.
Regards
skrao

You can configure SNMP traps for CPU Thresholding Notification.
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455772.html
You should be ok with the versions you list but check exact IOS version supports it at http://www.cisco.com/go/fn
If you do not want to use traps then there are specific oids that can be polled for 1minute average (1.3.6.1.4.1.9.2.1.57) and also 5 minute average (1.3.6.1.4.1.9.2.1.58). I've used these in the past with no problems. These oids may have been superceeded so check for latest. You can always snmpwalk a device to check oids.
The cisco SNMP navigator is helpful when it comes to oids.
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en
If you haven't got any SNMP configured yet on the switch check out http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddb4e54
HTH
--Phil

Can i change snmp poll time in PI 2.0 and how to ?

Can i change snmp poll time in PI 2.0 and how to ?
Thanks
Keith Chan

Hi Keith ,
yes it is 5 min by default .
You would need to create a new Monitoring template for this and deploy on the
devices on which you would like to change the polling frequency.
Go to Design --> Monitor Configuration --> Metrics
Choose the type of polling template i.e. Interface health or Device Health etc
Change the values and save it as a new template and deploy.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Prime SNMP-polls Component although Deleted

Hello!
After deleting ("Add / Import / Manage Devices") a non-Cisco component Cisco Prime (v.4.2.2) still SNMP-polls this component every day at 12:00 and 16:00. I removed the
"Default Credential Sets Policy Configuration" entry for this component and an entry in the "Seed Device" text field with the IP-address of this component but still the component is polled.
Strange is that the log-file of the component shows an "SNMP: Auth. failure" although the credential set for the component has the correct SNMP community string configured.
Question now is how to remove the component from Cisco Prime so that the polling no longer occurs.
Any help is very much appreciated!
Thanks,
Jakob

From your job Browser check which jobs are scheduled for 12:00 and 16:00.
Also, have a packet capture with the IP of the device which is removed too what kind of snmp request and which community string is being polled.
Till than if you want to make an ACL on device and restrict the LMS server IP and associate it to snmp as well, if possible, can be an option.

Device snmp polling

Hi All
Can you please help me out , how i m getting the logs of below,
for which snmp alerts ( snmp polling server 10.21.252.143) are generated from 172.29.131.26
where in 172.29.131.26 is the ASA firewall ip& 172.29.131.3 is CIsco Switch ip
Nov 30 2011 08:13:53: %ASA-4-313005: No matching connection for ICMP error message: icmp src
inside:172.29.131.3 dst identity:172.29.131.26 (type 5, code 1) on inside interface. Original IP payload: icmp src
172.29.131.26 dst 10.21.252.143 (type 0, code 0).
thanks

Anand,
icmp type 5 message is a redirect message. Is there another path between the source and the destination? I believe
172.29.131.3 - is a another L-3 deivce that is letting 172.29.131.26 this IP know of a different path between it
172.29.131.26 and 10.21.252.143.
-Kureli

SNMP Polling from UCS Manager 1.4

I am having trouble with SNMP Polling from UCS Manager 1.4(1j).
I seem to only get SNMP data from Nexus such as those described in (http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/mib/reference/NX5000_MIBRef.html) I don't see any OIDs corresponding to those mentioned specifically for UCS listed in (ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html).
Documentation on the cisco web site said that UCS Manager 1.4(1) and above will have MIBS such as CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB available.
Is there a separate IP addresses I should poll for these or any specific things that need to be set up?
I am not sure how we can gain access to the UCS related MIB objects exactly. The description on SNMP enable for UCS Manager is very brief (http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/1.4/UCSM_GUI_Configuration_Guide_1_4_chapter6.html#task_2054446421216050764)
It only described the community string set up under UCS Manager ->Admin->Communication Management -> Communication Services, bu didn’t really say anything about which IP addresses from the Management Interfaces should be used to get them.
Has anyone successfully polled data from say the CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB and be able to help?
Thanks in advance.

Yes indeed.
I learnt about the CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB and the other Cisco UCS Manager MIB Support list by selecting UCS Manager under the Unified Computing drop down on this http page you quoted.
(http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/mib/reference/UCS_MIBRef.html)
Is there anything specific from those docs you are referring to that would make it such that we get the Nexus MIBs rather than ones under UCS Manager?
The two IP addresses for Fabric Interconnect A and B under Management Interface only give us info from MIBs listed under the Nexus documentation only. Nothing fir say 1.3.6.1.4.1.9.9.719.1.15.
No SNMP data form the virtual IP address.
Not sure where data under 1.3.6.1.4.1.9.9.719.1.15 would be accessible

PI 1.2 High cpu on devices when snmp poll

        Hi all,
I´m setting up our new PI 1.2. After we discovered devices and successfully added, PI started to hit CPU devices every 10 minutes, when SNMP poll runs.
CPU utilization for five seconds: 99%/11%; one minute: 29%; five minutes: 17%
PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process
272    23536856     1524766      15436 86.62% 17.07% 5.06%   0 SNMP ENGINE
Is there any custom field to prevent this kind of snmp abuse on our devices?
If you need any further information, please let me know.
Regards

Hi there,
No, I didn´t!
HOSTNAME#sh processes cpu sorted | exc 0.00
CPU utilization for five seconds: 99%/29%; one minute: 50%; five minutes: 27%
PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process
285    97063956     5010425      19372 69.60% 31.80% 9.11%   0 SNMP ENGINE
136         324         196       1653 0.22% 0.29% 0.07% 388 SSH Process
129    15444024   112760917        136 0.15% 0.08% 0.08%   0 IP Input
248       67600      579359        116 0.15% 0.08% 0.08%   0 FNF Cache Ager P
83      660796    78806711          8 0.15% 0.13% 0.15%   0 Netclock Backgro
65      860544    19708629         43 0.07% 0.09% 0.09%   0 Per-Second Jobs
HOSTNAME#sh stacks 285
Process 285: SNMP ENGINE
Stack segment 0x31029AE4 - 0x3102C9C4
FP: 0x3102C8F0, RA: 0x23865C98
FP: 0x3102C918, RA: 0x2361E354
FP: 0x3102C988, RA: 0x237FC764
FP: 0x3102C9A0, RA: 0x237FC748
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1)
I will look for a router with IOS 12.something and I will perform some test. But for me, It´s something related to IP or routing table mib.
I´ll keep you aware.

Adding a 5108 chassis

We purchased UCS (2 6120XP fabric interconnects and 2 5108 chassis with blades) a couple of years ago. We are just getting to the point of needing to add an additional chassis. I'm presuming adding the additional chassis is pretty straight forward. Plug the chassis into the fabric interconnects, allocate the a couple of the ports on the fixed modules to be Server ports, and then power the chassis on. Is there anything that I need to be aware of or could be a potential gotcha?

When adding a new chassis the firmware shipped with the IOMs may be different than what you're currently running. The IOMs will automatically download the matching fw version from the FI's - so just be patient once enabling the server ports for the new chassis and blade to discover. Could take up to 20mins (to pull upgrade image and reboot if necessary).
Other than that, ensure all IOM - FI links are acknowledged. Once the chassis is discovered you can re-ack the new Chassis just to be sure.
Regards,
Robert

Getting SocketException: Error in poll for fd: 'nn', revents 'nn+n'

          I'm running WL 5.1 SP9 on a HP9000 HPUX 11.0 with JRE 1.2.2-06 and I get the following:
          java.net.SocketException: Error in poll for fd: '21', revents: '25'
               at weblogic.socket.PosixSocketMuxer.processSockets(PosixSocketMuxer.java:304)
               at weblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:23)
               at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:129)
          Any help appreciated.
          Please cc my email if possible
          Thanks
          Ricky


Derrick,
I believe that this is a spurious error caused by a HTTP client which
doesn't close the socket cleanly. This exception should be squelched in
newer versions of the product. Until you can upgrade I believe you can
safely ignore this message.
Regards,
Adam
"Derrick" <[email protected]> wrote in message
news:3a7834ef$[email protected]..
>
I am running apps server 5.1 on LINUX kernal 2.2 and using the POSIXperformance pack
that was listed in a thread on this newsgroup (libmuxer.so) and am gettingthe following
error sporatically...
Wed Jan 31 11:39:15 EST 2001:<E> <HTTP> Connection failure
java.net.SocketException: Error in poll for fd: '30', revents: '24'
atweblogic.socket.PosixSocketMuxer.processSockets(PosixSocketMuxer.java:290)
atweblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:23)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
Has anyone seen this error and if so, does this perofrmance pack have knowissues
with lost FDs? Should I run the app server without a performance pack ?
thanks in advance for you help.

Advice on Communication VI's - Polling for replies

Advice on Communication VI’s - Polling for replies
Hi all
I have been given the task of improving the performance my works communication vi’s. One of the main areas I have found that needs improving is how we implement a delay between a commands being transmitted and when we read back the data from the DUT. Currently we use the flowing steps:
• Convert text string into Hex
• Transmit Hex commands to DUT using appropriate protocol (TCP, USB)
• Wait Xms
• Read Reply
• Check Reply is valid
The main issue we have is that we adjust the X ms delay to cover the slowest possible command the DUT supports (~2 sec), however most command will return in ~20 ms. I am planning to replace the “wait X ms” vi with a vi that will continuously reads/polls until it receives a valid reply. This way communication vi will only delay for the require amount of time. This is the area I could do with some advice. Should I continuously poll/read to detect if a reply has been received, or is there a better method of detecting arrive of a reply?
Any advice would be gratefully received
D.Barr

Hi 148,
I have attached an example vi. It does not run as is just an indication of what i think you need. I wanted to just post a pic of it to give you and idea but my browser kept on crashing and im too intoxicated to figure out why so you can view the example instead.
Would be an idea to run a seperate loop that constantly scans the tcp read vi. If you set it in standard mode, it will either update all read bytes once 'bytes to read' is complete or update with the bytes read once the vi times out. This can then update a functional global that acts as a data buffer and message parser. Your main loop can then poll this for any new input messages. I havent included the functional global just an example of what the dedicated loop should do.
Hope this points you in the right direction. Im off to bed, goodnight.
Lucither.
"Everything should be made as simple as possible but no simpler"
Attachments:
TCP buffer.vi ‏8 KB

File adapter, trigger if no file is polled for pre-defined time

Hi',
I am polling for a file in a directory, my requirement is to notify by a email
if no file is polled for 1 hour or so, i.e. if no file comes in that directory for
long time.
Is there a way we can achieve this, I tried using a pick activity instead of
receive, however it does not allow on-alarm in this condition.
Please advice.
Thanks
Yatan

If you dont want to use database then you can do with your files as well, if at all you are archieving the files.
Say as soon as i get the files in the folder the adapter will read its content and then move it to archive folder, then you can have a logic to list the file and get the timestamp of the latest file from archive and compare with current time stamp and that will trigger a mail.
You can achive the above using API.
Thanks,
Vijay

Sender SFTP Adapter channel is not polling for files

Hello All,
Couple of SFTP sender adapter channel was failing in Developent system with u201Cdirectory listingu201D error.All SFTP sender channels stopped polling for the files in Developent system . We were unable to find the reason for adapter failure, Hence we restarted the j2ee server and adapter started polling files. Later we are facing the same issue in Quality system. THe adapter cahnnel is not polling files in Quality system even.
All lean tool adapters were showing the u201CHost key was not accepted erroru201D on 27th of Feb . As per the other channel trace, the time stamp of last successful polling and error time stamp of lean tool sender channels are exactly same
Eventhough two communication channels access the same SFTP adapter, one communicationchannel is getting 'Host key was not accepted error' but in other communication channel, files are getting picked.
Please let me know the solution if you have come accross this issue previously
Regards,
DilipKumar

Hi Mike,
Thanks for your reply.
Its not a standard SFTP adapter rather its a C-BURGER SFTP adapter.
Sorry I did not mention this in my previous post
Regards,
DilipKumar

File Adapter going into infinite mode while polling for the file

Hi,
I am facing an issue while the file adapter is reading the data from the file.
If the file from which it is reading has been deleted it keeps on polling for it infinite number of times and also doesn't pops out with any error message. Is there any method that after polling for some time period we can pop out a message that the particular file is not available and then the file adapter should stop polling for the file.Anyone has some ideas about this. Any pointers will be of great help.
Thanks
Vinay
Message was edited by:
soachd

Hi soachd,
As far as I understand polling is infinite process. You need to adopt this strategy if you are expecting some thing to happen all the time or may be when you want to be ready when ever an expected event happens. This provides a real time solution but with the downside of infinite execution.
Hope it helps.
Kalyan.

SNMP polling for 5108 Chassis

Similar Messages

Maybe you are looking for