Solaris 8 on this config?
I'd like to install Solaris 8 on a new pc configuration that I just put together. The system is stable with correct BIOS settings. The machine consists of:
1. ASUS A7V-133 motherboard.
2. AMD Thunderbird [266] 1.2 ghz processor. A Promise HD controller is
present which controls the ATA100 HD mentioned below.
3. 256mb of PC133 memory.
4. ASUS V7100 Pure 32mb GeForce video card.
5. Western Digital 40 gig [7200 rpm] ATA100 hard drive.
6. Creative SoundBlaster Live MP3 sound card.
7. I have Windows 98 SE loaded as the primary OS. I'd like to dual boot
Solaris 8 as the secondary OS.
8. ACER 50x max CD-Rom drive.
9. LG 12x-8x-32x CDRW drive.
Can I purchase and sucessfully install Solaris 8 on the configuration
posted above? Thanks in advance.
Solaris does not support the promise (raid) controller. Move the
HD (and all the other ide devices you want to access from solaris)
to the VIA PCI-IDE controller.
The IDE disk is >32GB, so make sure you use the latest solaris 8
release or boot using the 110202-01 ata driver patch diskette.
Solaris driver patches
I'm not sure solaris will support your video card. You can skip
the video card/monitor/mouse setup during installation and install
in text mode. Once the system is installed, have a look at patch
109401-06, the solaris 8 x86 video driver patch. If this patch
does not add support for your video card, you either have to
install the xfree86 X11-Server or exchange the video card to one
that is supported by solaris.
The Soundblaster Live audio card is not supported by solaris 8.
You may have luck with the OSS (OpenSoundSystem) audio drivers.
Similar Messages
-
Define Logical Port and Back-End Destinations for ESOA use of this config
Hi,
Please let me know what is the use of this config I am not able to get a documentation.
Define Logical Port and Back-End Destinations for ESOAHi Autobots,
Even I am looking for the same information. Did u get some headstart into the matter?
Pl provide me with the inputs too.
Cheers
Nikhil -
What is going wrong with this config ??
Hello guys,
I am busting my head to find out what is going wrong with this config and cant figure it out since i am not an advanced cisco technician.
Problem is that i cant access the 94.70.142.127 server that is supposed to be in a DMZ zone.
I know it is a bit chaotic but would really appreciate any help since i am running on a deadline.
I am building the config step by step and although it seems to be working access to the server all of the sudden is denied.
No idea if its a NAT issue a firewall issue or a security audit issue.
There are 3 vlans.
Vlan 1 is the inside network.
Vlan 2 is the DMZ server
Vlan 3 is the Management Network.
thanks in advance
Building configuration...
Current configuration : 11796 bytes
! Last configuration change at 11:28:33 PCTime Fri Jan 4 2013 by admin
! NVRAM config last updated at 11:27:51 PCTime Fri Jan 4 2013 by admin
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime
service password-encryption
service sequence-numbers
hostname R1
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 8
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$oT7y$BwhdEjMJfAaTQI3dzDVwP.
no aaa new-model
memory-size iomem 10
clock timezone PCTime 2
clock summer-time PCTime date Mar 30 2003 3:00 Oct 26 2003 4:00
crypto pki trustpoint TP-self-signed-2567543707
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2567543707
revocation-check none
rsakeypair TP-self-signed-2567543707
crypto pki certificate chain TP-self-signed-2567543707
certificate self-signed 01
30820244 308201AD A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32353637 35343337 3037301E 170D3133 30313032 30383431
35335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 35363735
34333730 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100ABA4 B7FFF4F1 9FBE79D8 2CEBCA68 A14BE3AB DBF770C2 EB35A954 B271AE3E
F8485837 F2E8566B 66E5EF6B BCFCDFA3 8F6F91F3 FD8E3015 879A67F5 85DD95F5
C26875C0 2202CA6C CE95888F 545AB4F6 6F708A0E C65E78D1 60967480 5589F5EE
80505E46 8767CE2C 37C994FE AB555AF0 BA4C4679 63FF7641 34FFF6EF 3EC38006
46B90203 010001A3 6C306A30 0F060355 1D130101 FF040530 030101FF 30170603
551D1104 10300E82 0C52312E 646F636E 65742E67 72301F06 03551D23 04183016
8014F0DE 85318FB3 70C36B4A FEB4B0CA 446025F0 329C301D 0603551D 0E041604
14F0DE85 318FB370 C36B4AFE B4B0CA44 6025F032 9C300D06 092A8648 86F70D01
01040500 03818100 5D76D5F4 5FB659C3 1E5B3777 420E1703 CD019889 AE79390D
A2AA4D26 AD9913B4 B3292277 97ACACDD D7093465 78279B4D 5FAC0A21 EFBF3B74
6A25BC5B ACFB648F 08F92678 00BB495C 037DEAF7 C5910944 3D2C0643 EA19E9BD
0AFE5423 AADBB3C2 B2C94296 DABE0D3D 6438F7A8 32B0A92B 3E8E0D26 635070A3
ACF87E49 65A9E468
quit
no ip source-route
ip cef
no ip bootp server
ip domain name docnet.gr
ip name-server 195.170.0.1
no ipv6 cef
username admin privilege 15 view root secret 5 $1$Lny5$et1FhWOpIKOOYRUtN89H10
archive
log config
hidekeys
ip tcp synwait-time 10
ip ssh version 2
class-map type inspect match-any WebService
match protocol http
match protocol https
class-map type inspect match-all sdm-cls-sdm-pol-NATOutsideToInside-1-1
match class-map WebService
match access-group name WebServer
class-map type inspect match-all ccp-cls-sdm-pol-NATOutsideToInside-1-1
match access-group name Spoofing
class-map type inspect match-any CCP-Voice-permit
match protocol h323
match protocol skinny
match protocol sip
class-map type inspect match-any tcp-udp
match protocol http
match protocol https
match protocol dns
match protocol icmp
class-map type inspect match-all ccp-cls--3
match access-group name mng-out
match class-map tcp-udp
class-map type inspect match-all ccp-cls--2
match access-group name mng-self
class-map type inspect match-all ccp-cls--4
match access-group name mng-out-drop
class-map type inspect match-any ccp-cls-insp-traffic
match protocol cuseeme
match protocol dns
match protocol ftp
match protocol h323
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp extended
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any http-https-DMZ
match protocol http
match protocol https
class-map type inspect match-all sdm-cls--2
match class-map http-https-DMZ
match access-group name web_server
class-map type inspect match-any MySQLService
match protocol mysql
class-map type inspect match-all sdm-cls--1
match class-map MySQLService
match access-group name DMZtoMySQL
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-all sdm-nat-https-1
match access-group 102
match protocol https
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
inspect
class class-default
pass
policy-map type inspect sdm-pol-NATOutsideToInside-1
class type inspect ccp-cls-sdm-pol-NATOutsideToInside-1-1
drop
class type inspect sdm-cls-sdm-pol-NATOutsideToInside-1-1
inspect
class type inspect sdm-nat-https-1
inspect
class class-default
drop
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
drop log
class type inspect ccp-protocol-http
inspect
class type inspect ccp-insp-traffic
inspect
class type inspect CCP-Voice-permit
inspect
class class-default
drop
policy-map type inspect ccp-permit
class class-default
drop
policy-map type inspect sdm-policy-sdm-cls--1
class type inspect sdm-cls--1
inspect
class class-default
drop
policy-map type inspect ccp-policy-ccp-cls--1
class class-default
drop
policy-map type inspect ccp-policy-ccp-cls--3
class type inspect ccp-cls--3
inspect
class class-default
drop
policy-map type inspect sdm-policy-sdm-cls--2
class type inspect sdm-cls--2
inspect
class class-default
drop
policy-map type inspect ccp-policy-ccp-cls--2
class type inspect ccp-cls--2
inspect
class class-default
drop
policy-map type inspect ccp-policy-ccp-cls--5
class class-default
drop
zone security out-zone
zone security in-zone
zone security dmz-zone
zone security mng
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security sdm-zp-NATOutsideToInside-1 source out-zone destination in-zone
service-policy type inspect sdm-pol-NATOutsideToInside-1
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
zone-pair security zp-dmz-to-outside source dmz-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security zp-outside-to-dmz source out-zone destination dmz-zone
service-policy type inspect sdm-pol-NATOutsideToInside-1
zone-pair security sdm-zp-dmz-zone-in-zone source dmz-zone destination in-zone
service-policy type inspect sdm-policy-sdm-cls--1
zone-pair security sdm-zp-in-zone-dmz-zone source in-zone destination dmz-zone
service-policy type inspect sdm-policy-sdm-cls--2
zone-pair security sdm-zp-dmz-zone-self source dmz-zone destination self
service-policy type inspect ccp-policy-ccp-cls--1
zone-pair security sdm-zp-mng-self source mng destination self
service-policy type inspect ccp-policy-ccp-cls--2
zone-pair security sdm-zp-mng-out-zone source mng destination out-zone
service-policy type inspect ccp-policy-ccp-cls--3
zone-pair security sdm-zp-out-zone-mng source out-zone destination mng
service-policy type inspect ccp-policy-ccp-cls--5
interface Null0
no ip unreachables
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
encapsulation hdlc
shutdown
isdn termination multidrop
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
no atm ilmi-keepalive
interface ATM0.1 point-to-point
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
pvc 8/35
pppoe-client dial-pool-number 1
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
switchport access vlan 3
spanning-tree portfast
interface FastEthernet3
switchport access vlan 2
interface Vlan1
description $FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
zone-member security in-zone
ip tcp adjust-mss 1412
interface Vlan2
description $FW_INSIDE$
ip address 192.168.1.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
zone-member security dmz-zone
interface Vlan3
description $FW_INSIDE$
ip address 10.0.10.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
zone-member security mng
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly max-reassemblies 64
zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [email protected]
ppp chap password 7 0918425001505245
ppp pap sent-username [email protected] password 7 13511B4B1359417D
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 10.0.10.0 255.255.255.0 Vlan3
no ip http server
ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static 192.168.0.101 94.70.142.113
ip nat inside source static 192.168.1.102 94.70.142.127
ip access-list extended DMZtoMySQL
remark CCP_ACL Category=128
permit ip host 192.168.1.102 host 192.168.0.101
ip access-list extended Spoofing
remark CCP_ACL Category=128
permit ip 10.0.0.0 0.255.255.255 any
permit ip 192.168.0.0 0.0.255.255 any
permit ip 172.16.0.0 0.15.255.255 any
ip access-list extended VTY_incoming
remark CCP_ACL Category=1
permit ip host 10.0.10.2 any
ip access-list extended WebServer
remark CCP_ACL Category=128
permit ip any host 192.168.1.102
ip access-list extended mng-out
remark CCP_ACL Category=128
permit ip 10.0.10.0 0.0.0.255 any
ip access-list extended mng-out-drop
remark CCP_ACL Category=128
permit ip any any
ip access-list extended mng-self
remark CCP_ACL Category=128
permit ip any any
ip access-list extended web_server
remark CCP_ACL Category=128
permit ip 192.168.0.0 0.0.0.255 host 192.168.1.102
logging 10.0.10.2
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 remark VLan 1 Access
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 1 remark VLan 3 Access
access-list 1 permit 10.0.10.0 0.0.0.255
access-list 1 remark Vlan 2 Access
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
access-list 102 remark CCP_ACL Category=0
access-list 102 permit ip any host 192.168.0.101
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner login ^CWARNING!!!This is a highly monitored private system. Access is prohibited!!^C
line con 0
no modem enable
line aux 0
line vty 0 4
access-class VTY_incoming in
password 7 12292504011C5C162E
login local
transport input ssh
scheduler max-task-time 5000
ntp authentication-key 1 md5 10603D29214711255F106B2677 7
ntp authenticate
ntp trusted-key 1
ntp master 2
endHello karolos,
Here is the thing.
You said you are trying to access 94.70.142.113 and that is a server on the DMZ but based in your configuration that is not true
ip nat inside source static 192.168.0.101 94.70.142.113
So 192.168.0.101 is on Vlan 1 witch is the in-zone
interface Vlan1
description $FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
security in-zone
If you got confused with the security zone that the host is assigned to then just add the following and it should work
ip access-list extended WebServer
permit ip any host 192.168.0.101
Regards -
Modifying Solaris 10 perl Config.pm values
Numerous perl packages won't
build on my Solaris 10 systems
because the Solaris 10 perl's
Config.pm packages identifies
$Config{'cc'} as "cc" and not
"gcc".
I'd like to just update Config.pm
to just point to gcc and not cc.
Is there a better way to
do this with the Config module,
other than just editing Config.pm?
Thanks --wwsanders wrote:
I'd like to just update Config.pm
to just point to gcc and not cc.
Is there a better way to
do this with the Config module,
other than just editing Config.pm?If you don't want to download studio and get a 'cc' compiler, and you don't just want to compile your own perl (that's the way I usually go, so I can leave the system perl alone), then just use perlgcc.
/usr/perl5/bin/perlgcc -MCPAN -e shell
(blah blah blah...)
This will set things so that for that invocation of perl, it will prefer to use 'gcc' and gcc appropriate flags. If you look at what it does, it just uses an alternate 'Config.pm' and sticks it in the perl environment ahead of the default one.
Darren -
Solaris 10 zone config for JES
Setup a zone to install JES - Web servers, but when I launch the installer I get the following:
WARNING: Unsupported non-global zone
EntSysResources:zoneCheckPanel-Gui-LocalZoneSupported
Something in the zone setup is incorrect, but not sure what.
Anyone else out running JES in Solaris 10 zones?
Thanks!
Steve
[email protected]From docs.sun.com -
The following Java ES and zones scenarios are supported in this release of Java ES:
* Installing Java ES in a non-global zone that uses the whole root file system (Using the default sparse root file system is not supported.)
* Installing Java ES in the global zone with no non-global zones
Zone can be 2 type - sparse root and whole root . sparse root model has following folders inherited - /lib, /platform, /sbin and /usr.
If a non-global zone doesn't have any inherit-pkg-dir resources, such a zone is said to be a whole root one
If you want to create a whole root zone but default shared file systems resources have been added by using inherit-pkg-dir, you must remove these default inherit-pkg-dir resources using zonecfg before you install the zone:
zonecfg:my-zone> remove inherit-pkg-dir dir=/lib
zonecfg:my-zone> remove inherit-pkg-dir dir=/platform
zonecfg:my-zone> remove inherit-pkg-dir dir=/sbin
zonecfg:my-zone> remove inherit-pkg-dir dir=/usr -
Solaris 10 zone config for one application
I have a Solaris 10 x86 server with 48GB of memory and 8 CPUs (although I believe hyperthreading is turned on because prsinfo shows 16 CPUs). The server is dedicated to one big application which spawns many processes/threads. Performance is extremely important for this application so I need to give it all of the resources possible.
I tried just allowing the application to run in the global zone because there's nothing else it will interfere with (aside from the OS) but I couldn't get it to utilize all of the CPUs this server has. My guess is the global zone is only designed for running the OS and playing traffic cop for the other zones, so it's not suited for running applications. Is that correct?
So my question is, assuming I do need to setup a dedicated zone for this monster application, how do I configure it to dedicate all CPUs and all memory (or as close to all of it as I can get)?
Also, is there some default limit on how much CPU % a process can have? Because I have tried getting one process to utilize 100% of a CPU and can't get anywhere near that... unless prstat doesn't display per CPU utilization information.
Any help would be appreciated.Kupacmac wrote:
I have a Solaris 10 x86 server with 48GB of memory and 8 CPUs (although I believe hyperthreading is turned on because prsinfo shows 16 CPUs). The server is dedicated to one big application which spawns many processes/threads. Performance is extremely important for this application so I need to give it all of the resources possible.
I tried just allowing the application to run in the global zone because there's nothing else it will interfere with (aside from the OS) but I couldn't get it to utilize all of the CPUs this server has. My guess is the global zone is only designed for running the OS and playing traffic cop for the other zones, so it's not suited for running applications. Is that correct?No. Unless you have dedicated CPUs to zones (so they are not available to the global zone), or unless you're running under a project which restricts CPU usage, the global zone has access to all virtual CPUs.
Can you see your process spawning threads? How much CPU is it able to use?
Also, is there some default limit on how much CPU % a process can have? Because I have tried getting one process to utilize 100% of a CPU and can't get anywhere near that... unless prstat doesn't display per CPU utilization information.One thread can only use one CPU. So you'd either need to run 16 single threaded processes, or your process would need to spawn 16 threads that were CPU-heavy. No, there's no default limit on a process.
Darren -
Can a RVL200 connect to BEEVPN with this config?
Hi all,
Hope someone can help me get clear on this. I'm in doubt whether I should buy a RVL200. I'm no expert in VPN or routers.
I would like to know whether or not I can use a RVL200 to establish an Ipsec tunnel to BEEVPN-service (beevpn.com).
They themselves use cisco equipment to connect to their customers.
They request the following configuration of me:
Server: use "*****.beevpn.com"
Account/Login/Username: Use your beevpn username.
Password: Use your beevpn password.
Group/Groupname: use "*******"
Shared key/Shared secret: use "*******"
Can I config the RVL200 to those requirements? Then i'll happily buy one
Regards
KaspermathiasI checked my 4 extremes and found that the 3 mac mini's, 2 powerbook's, 1 imac, and 1 xserve do connect to the closest extreme.
I have 1 extreme in the middle of the 2nd floor as the gateway. An extreme on the third floor for 2 mac mini's, an extreme on the far end of the second floor for an imac and a powerbook, and extreme on the 1st floor for a mac mini, powerbook, and xserve.
One item for consideration to help control access is by manipulating the min connect speed dialog box. The default is 1 mb. Up that number until your clients become ineligble to connect to distant routers. As cleints move away from routers, their connection speed reduces. -
Getting FTP to work in Solaris 10, RE: config vs. firewall
We've recently migrated from a clustered Solaris 9 environment to Solaris 10 zones.
One issue that keeps coming up is the inability to ftp anywhere except within zones running on the same server. I can ftp between those zones without any problem.
Trying to ftp anywhere else, i.e. to a zone on another server node or to any other ftp server, I encounter one of two problems, either I don't get a login prompt at all, which leads me to think there's a firewall issue, or I can login fine, but when I issue any command, nothing happens, and upon ctrl-x'ing out I see:
"421 Service not available, remote server has closed connection"
I've seen a lot of totally useless stuff on the web that doesn't seem to apply to Solaris 10. I know there's a bunch of ftp configuration files, but we haven't touched them.
ftpd is running with the -a switch, but TCP Wrappers is set to false. I can ftp TO this server from a remote server as long as the firewall has been configured for the IP.
To summarize.
Zone A on Server A > Zone B on Server A : No problem
Zone A on Server A > Zone B on Server B: Problem
If anyone can shed any light on this problem, that would be great.
Edited by: tsmori on Feb 7, 2008 8:26 AMDoes perl work for ~/andrew? You have ExecCGI set for /home/andrew/public_html and not /home/*/public_html:
<Directory "/home/andrew/public_html">
Options Indexes FollowSymLinks ExecCGI
AllowOverride None
Order allow,deny
Allow from all
</Directory>
Are permissions set to 755 so that the http user can run them? Have you checked apache's error log?
edit: fixed quote
Last edited by juster (2009-12-12 18:56:40) -
Org Unit inheritance link to Parent Cost Center - is this Config?
Hi
We started at a new client and have difficulty maintaining the Org Structure A 011 relationships to child Org Units. The system undoes our implicit links. We want the implicit links to be there and not inherited. Is it possible to switch off the inheritance in config?
Please assist/advise.
Thank you, Adrianwhat do you mean when you say the system 'undoes' your implicit links? Did you mean the system undoes the inherited cc value by using the explicit cc-assignment done at an org unit level? if yes that is how sap works,... the options are
a. do not do explicit creation of cost center to org unit . that way assigning a cost center at the top org unit will suffice as that will be inherited to all org units down the structure. But this is not a workable business scenario at all.
b. determine the explicit cost center assignments at each org unit level and do the assignment accordingly.
lastly : I dont think inheritence of cost center is something you can deactivate in img.
cheers -
I/O issues with Oracle Financials on Solaris (Is this normal ?)
Oracle Financials: Constant and High "Read" I/O:
Problem Description:
Most of the I/O on all of our 3 Oracle Financial 11.5.9 servers is read intensive and they are all going against 2 HOT applsys database files causing constant high I/O even when the application is not in use.
Example:
r/s w/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device
274.7 8.6 2197.2 19.2 0.0 0.4 0.0 1.6 0 44 0 0 0 0 c4t0d0s0
674.7 5.6 5397.7 11.6 0.0 2.3 0.0 3.4 0 100 0 0 0 0 c6t0d0s0
extended device statistics ---- errors ---
r/s w/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device
434.6 6.0 3476.5 16.6 0.0 0.8 0.0 1.8 0 58 0 0 0 0 c4t0d0s0
838.1 3.4 6704.6 7.5 0.0 2.0 0.0 2.4 0 98 0 0 0 0 c6t0d0s0
Hardware: Single Node Sun V880 2 Instances - SUN DAS Storage
The A1000 DAS Array is configured for random I/O
Operating System Modifications:
I have toggled with the Filesystem mount options noatime,forcedirectio,logging but it did not make a difference.
The Solaris Directory Name Lookup Cache hits is 98% - OK
The buffer_cache_lookups & buffer_cache_hits numbers are very close - OK
Question:
I am pretty sure distributing the applsys tablespace and across six file systems will help?
What is the best way to do this in Oracle Financials?
If you are running solaris please run the following command and share your output.
# iostat -xPne 20 | nawk '( /r\/s/ || $1 > 200 ) && ! /:/'Pl do not post duplicate threads - Oracle XE is not running on startup
-
Can some one cross check this config file..
can some one cross check the below config file..specially the 2mb memory allocation for front(local) cache..should i specify the <unit-calculator>BINARY</unit-calculator> since i allocated 2mb for local cache..
<?xml version="1.0"?>
<!DOCTYPE cache-config SYSTEM "cache-config.dtd">
<cache-config>
<caching-scheme-mapping>
<cache-mapping>
<cache-name>dist-statedaemon</cache-name>
<scheme-name>nearcache</scheme-name>
<init-params>
<init-param>
<param-name>front-size-limit</param-name>
<!--
default limit of 2MB for local cache
-->
<param-value system-property="front.size.limit">2097152</param-value>
</init-param>
</init-params>
</cache-mapping>
</caching-scheme-mapping>
<caching-schemes>
<local-scheme>
<scheme-name>localcache</scheme-name>
<eviction-policy>LRU</eviction-policy>
<high-units>{front-size-limit 0}</high-units>
</local-scheme>
<near-scheme>
<scheme-name>nearcache</scheme-name>
<front-scheme>
<local-scheme>
<scheme-ref>localcache</scheme-ref>
</local-scheme>
</front-scheme>
<back-scheme>
<distributed-scheme>
<scheme-ref>dist-default</scheme-ref>
</distributed-scheme>
</back-scheme>
<invalidation-strategy>present</invalidation-strategy>
</near-scheme>
<distributed-scheme>
<scheme-name>dist-default</scheme-name>
<service-name>DistributedCache</service-name>
<serializer>
<class-name>com.tangosol.io.pof.ConfigurablePofContext</class-name>
</serializer>
<local-storage>false</local-storage>
</distributed-scheme>
</caching-schemes>
</cache-config>Hi
I'm not exactly clear on what you are attemting to do. However you first need to have at least one storage enabled configuration and then you need to have a backing map.
So your configuration should look somthing like this:
<?xml version="1.0"?>
<!DOCTYPE cache-config SYSTEM "cache-config.dtd">
<cache-config>
<caching-scheme-mapping>
<cache-mapping>
<cache-name>dist-statedaemon</cache-name>
<scheme-name>nearcache</scheme-name>
<init-params>
<init-param>
<param-name>front-size-limit</param-name>
<!--
default limit of 2MB for local cache
-->
<param-value system-property="front.size.limit">2097152</param-value>
</init-param>
</init-params>
</cache-mapping>
</caching-scheme-mapping>
<caching-schemes>
<local-scheme>
<scheme-name>localcache</scheme-name>
<eviction-policy>LRU</eviction-policy>
<high-units>{front-size-limit 0}</high-units>
</local-scheme>
<near-scheme>
<scheme-name>nearcache</scheme-name>
<front-scheme>
<local-scheme>
<scheme-ref>localcache</scheme-ref>
</local-scheme>
</front-scheme>
<back-scheme>
<distributed-scheme>
<scheme-ref>dist-default</scheme-ref>
</distributed-scheme>
</back-scheme>
<invalidation-strategy>present</invalidation-strategy>
</near-scheme>
<distributed-scheme>
<scheme-name>dist-default</scheme-name>
<service-name>DistributedCache</service-name>
<serializer>
<class-name>com.tangosol.io.pof.ConfigurablePofContext</class-name>
</serializer>
*<backing-map-scheme>*
*<local-scheme>*
*<scheme-ref>localcache</scheme-ref>*
*</local-scheme>*
*</backing-map-scheme>*
<local-storage> true </local-storage>
</distributed-scheme>
</caching-schemes>
Thanks
/Charlie -
Looking for this config file that I can specify language to show on trace panel
Basically, I'm using a Window where the language(Control panel >Regional) is set to KOREAN so, in trace panel, the error message shows up in Korean but, I know in somehwere in Flex application application folder that there is a some type of config file that I can modify to something else like... EN for english.
Does anyone know where that is in both Mac & Win?
Thanks,
BaBo,You can right click the tab and choose "Close Tab" to close a tab.
Some menu entries are hidden by default and only appear if you use the keyboard to open the menu.
You can see the difference if you use Alt+F or Alt+B to open the "File" and "Bookmarks" menu and compare that to what you see if you use the mouse to open the menu after you have made the menu bar visible by pressing Alt or by pressing F10.
Press F10 or press and hold the Alt key down to bring up the "Menu Bar" temporarily. -
Reccommended power supply for this config...
I am looking to install a couple SATA HDs in my rig. I currently have just the PS that came with my case, 420W. This is what my system will look like with the two new HDs:
MSI Neo2 LS mobo
2.4C P4
1 GB Corsair PC3200
Pioneer DVD Rom
Sony 52x CD burner
Floppy drive
WD 120GB IDE HD
Maxtor 160 GB IDE HD
Hitachi 160 GB SATA HD (x2)
Radeon 9800 128 MB (non pro)
Thermaltake HSF
80mm case fans (x2)
These are all the things that I can think of that will draw power off the PS. What wattage should I have and what kind of amperage would I want on the 12v rails to get the most stable machine?Quote
What wattage should I have and what kind of amperage would I want on the 12v rails to get the most stable machine?
sgweber, Not to be funny but as much as you can get
What are you planing to do with your machine ?
Are you going to overclock it?
What is your current PSU specs?
With my system I feel that the power supply unit I have is marginal at best
( see my signature for specs) because
1- I have a prescott (some guys just like punishment )
2- I am overclocking the heck out of it
3- I have more fans running in this thing trying to keep it cool than I do in my home
4- Two optical Drives (CDR and DVD)
5-Two hard drives
6- My memeory volts pushed up to 2.7( not sure if this puts any kind of strain on the unit)
7- some other stuff that I can't remember
Dave -
How to fix this Config ADS Connection ???
Dear all,
I testing ADS connection, (login transaction SM59, create ADS connection, and test it. I check the pasword of ADSUer in SU01 and in logon&Security in SM59 is the same).
- It display a dialog box: "Respose from Web Server contains cookies. Accept ?"
- I check Accept all further cookies. and click YES.
- Then a login dialog box appear, request to enter UserName, Password . Which account I should use to login ?
- Sometimes it go directly to the result ( login diaglog does not appear ), but the Result is: ~status_reason: Forbidden.
What is going on here? How can I fix this?Did you activate the services in SICF?
Markus -
What would this config actually do (srr-queue)
I have seen this interface configuration around on a few switches in my network.
interface GigabitEthernet1/0/10
switchport access vlan 2
srr-queue bandwidth shape 0 0 0 0
What would the srr-queue command do here? there is nothing else on the interface.
I think it pretty much does nothing, but just not 100% sure.
thanksHi,
This command is used for shaping the traffic. Do you have QOS enabled on the switch?
Issue show mls qos, to check if you have enabled it.
Here you have SRR shape weight to zero for all queues so effectively no shaping is applied. For example if you had something like srr-queue bandwidth shape 30 0 0 0, it would have restricted the first queue to “1/30” of the interface bandwidth (which is approximately 3.3Mbps for 100Mbps interface and approximately 330Kbps for a 10Mbps interface) and rest of the queues would have shared rest of the interface bandwidth.
For more details you may go through the following:
http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_50_se/configuration/guide/swqos.html#wp1163879
Thanks
Ankur
"Please rate the post if found useful"
Maybe you are looking for
-
I can't update my apps without a credit card?
Hello! I've came across a problem I've had a apple device for about 3 years and had no problems with it what so ever. Recently I tried to update my games through the app store I got prompt with a message saying that my account has not been used befor
-
Hi i had selcted the accurals in condn type and assingned a key of fr3 . here my cenvat condition values shud not add to material . but still i see the values are cumulated at GR . Please help how to avoid chris
-
I have a one page composite document with photos and text that I have been printing for years without problems. Now when I print the document the colors are washed out, grainy, almost like it's in draft mode. I can't seem to find what setting has cha
-
Cant play Mac made FCE4 QT movie on PC
OK - so I made a movie with my new FCE4, exported as a Quicktime movie, 720p25 etc etc. The movie is 346mb, I burnt it to disk and my son's PC can't see the data on the disk let alone try to play it. He has the latest QT on his PC. What's going on? I
-
CRIO9075 Ecrire/lire un fichier Csv
Bonjour, Voilà j'utilise un CRIO 9075 en scan interface et je voudrais, à partir d'un VI real-time, écrire dans un fichier csv qui se trouve sur mon PC. Voilà comment j'ai présenté mon projet, j'ai un VI "Classement" qui permet de lire et d'écrire su