[SOLVED] How to unload any driver(dll) at the start up after reset??

Dear Developers,
Greetings!!!
As, I am using AM335x BSP with WinCE 7. We have one vendor Wifi device and its binary images(driver installer). When we reset the target board, the modules do not reset and during the time of board booting, I found the following logs
7771 PID:400002 TID:9e0006 Warning! Kernel DLL 'rwlpsdio.dll' is registered for thread creation/deletion notification. To improve performance if you dont need thread notifications call DisableThreadLibraryCalls from inside D
7774 PID:400002 TID:9e0006 DriverEntry!!!!!!!!!!!!!
7777 PID:400002 TID:9e0006 SDIO not initialized, returning!!!!!!!!!!!!!!
7778 PID:400002 TID:9e0006 OSAXST1: <<< Unloading Module 'rwlpsdio.dll' (0x9E438000) at address 0xA7C90000-0xA7D47000 in Process 'NK.EXE' (0x87FDFAD0)
PB Debugger Unloaded symbols for 'rwlpsdio.dll'
We conclude that when we reset the device, the driver is not unloading and that why, its not releasing the resource. 
My motto to solve the issue by creating an application that run at every startup after reset and unload the driver. So, that during the time of loading it, it re-loads properly..
I am searching it on google but unable to find any way so far.
ASAP reply must be highly appreciated 

Dear Developers,
@balaji,
As I had read the link https://social.msdn.microsoft.com/Forums/en-US/98aa5eca-0b38-4f6e-bf7b-81cb7068422e/sdio-wifi-driver-and-prefetch-aborts-problem?forum=winembplatdev
And, in the above thread you were replying as 
Hi Misbah,
NdisMRegisterMiniport sure needs to be called from DriverEntry. Can you check if NdisRegisterAdapter is present. This ideally should be somewhere in your stream interface. 
I am taking a wild guess here , perhaps you can may be introduce some delay in DriverEntry , so that the stream driver gets a chance to load?.
e.g. you can use one of NdisWaitEvent functions.
All the best.
Regards,
Balaji.
As, per my knowledge, the DriverEntry is the first function that is called by ndis after loading the ndis.dll and it is responsible for registering the driver with NDIS by  using
NdisRegsiterMiniportDriver.  
Any how in my case, DriverEntry is called but the same function we are getting one error and that's why driver is not registered with NDIS.
We are checking SDIO  interface status, either it is uo or not. If it is up then fine and if not then display warning and unload the driver.
So, in my case, the SDIO status is not up after resting the device.
Any suggestion will be appreciated????

Similar Messages

  • I have an issue with Acrobat, after a few uses, the program will not load, the only way to fix it is to completely uninstall the CS suite wipe the drive and reinstall the software, then after a few uses it stops working, how do i fix this?

    after a few uses, the program will not load, the only way to fix it is to completely uninstall the CS suite wipe the drive and reinstall the software, then after a few uses it stops working, how do i fix this?

    Not sure of an answer to your basic question, but it may be that you can run a repair (on Windows --> Control Panel>Programs & Features and run the repair on Acrobat). If that fixes the issue, at least temporarily, at least you will not be reinstalling everything -- a real pain.
    Next, open Acrobat and go to the Help to run the updates and be sure you are current. On some OSs, the updates are critical.

  • How long can you revert back to the original photo after cropping?

    Is there any time limit for how long can you revert back to the original photo after cropping? Are you always able to revert back?
    Thanks.

    DAM = "Digital Asset Manager", a fancy name for a filing system.
    iPhoto keeps the original and makes one (usually much smaller) copy based on your edits. It is non-destructive in that if you crop, and later change the color, iPhoto will go back to the original and apply the corrections to get the new image, it will not simply modify the preview.
    If you want a high quality copy of the image, use the export function which allows you to specify the size and compression.

  • How do I add web part in the event receiver after the site is provisioned in SP 2010?

    How do I add web part in the event receiver after the site is provisioned in SP 2010?

    You try the below steps:
    1. Use long operation to provision the site, so that it does not time out in process.
    2. After provisioning, you can add a page or add the web part directly to landing page of site.
    For each of the above steps you can find the sample code pieces.
    if you couldn't get that, let me know. I will share with you.
    Thanks, Ashish If my response has helped you, please mark as answer.

  • On windows 7 pro, how do i add firefox bookmarks to the start menu?

    On Windows 7 professional, how do I add firefox bookmarks to the start menu so I can access my bookmarks without opening firefox first?

    Only Favorites can be displayed as a submenu of the Start Menu. You can convert your Firefox bookmarks to IE favorites as follows:
    # [[Exporting bookmarks to an HTML file|Export your bookmarks to an HTML file]].
    # [http://windows.microsoft.com/en-us/windows7/Import-or-export-favorites-in-Internet-Explorer Import the bookmarks in Internet Explorer].
    # In Firefox, install [https://addons.mozilla.org/firefox/addon/plainoldfavorites/ the PlainOldFavorites extension]. This will allow you to create and manage favorites from Firefox.
    # Alternatively, if you use both browsers, you can keep bookmarks and favorites synchronized with an extension like [https://addons.mozilla.org/firefox/addon/xmarks-sync/ Xmarks Sync].

  • How to do that when you open a new tab to appear like the start page after opening the browser?

    How to do that when you open a new tab to appear like the start page after opening the browser?

    https://addons.mozilla.org/en-US/firefox/addon/newtaburl/
    Never used it myself, so I'm not sure if you can set to about:home or not. You'll have to give it a try.

  • Why can't I make any calls on facetime, the call drops after saying connecting.

    Why can't I make any calls on facetime, the call drops after saying connecting for a few seconds. I'm using an iphone 5, 32 GB on IOS 6.0.1 over 3G network in Muscat, Oman. Just to be clear, I was able to make facetime call in Muscat about a week ago.

    If this user to user forum could not help you with your issue, contact Apple to get your Device serviced or looked at.
    http://www.apple.com/contact/

  • How to Stop Firefox 18 From Restoring the Previous Session After a Crash

    Firefox 18.0.1 running on Windows 7
    When Firefox crashes, the next time it opens it tries to restore the previous session. I do not want Firefox to restore the previous session after a crash. How do I prevent Firefox from restoring the previous session after a crash?
    Please note:
    1- My home page is set to "blank page"
    2- I have configured Firefox to NOT remember my browsing history, download history, form fields and passwords.
    3- Even in Safe Mode (i.e., with all add-ons disabled), Firefox STILL restores the previous session after a crash.

    hello Bulldogger, please try the following in order to switch off sessionrestore completely: enter '''about:config''' into the firefox location bar (confirm the info message in case it shows up) & search for the preferences named '''browser.sessionstore.max_tabs_undo''' and '''browser.sessionstore.max_windows_undo'''. double-click on those entries and change both of their values to '''0'''.
    http://kb.mozillazine.org/Browser.sessionstore.max_tabs_undo
    http://kb.mozillazine.org/Browser.sessionstore.max_windows_undo

  • I have an IPhone 4s and am getting an IPad Mini. Do I have to change my Verizon plan in any way to include the IPad?  After all I already have the phone number.

    I have an IPhone 4s and am getting an IPad Mini. Do I have to change my Verizon plan in any way to include the IPad?  After all I already have the phone number.

    Gina your post was very helpful to me as well. I recently Traded In my Apple IPad 3 WIFI Only Device for a Verizon Wireless Apple IPad Mini Pre-Order. This is actually my very first WIFI + Cellular IPad Purchase. The Price was Finally Affordable.

  • How do you clear completed updates from the app store after downloading is complete?

    How do you clear completed updates from the app store after downloading is complete on iOS 7.0.2?

    You don't. It's how things are done now, likely to accommodate those that have auto update turned on.  IT's been said that the updates will just drop off after a period of time but  time will tell on that.

  • Iphone can't start up after reset.how do i get it to start up again?

    iphone 3gs cannot start up after reset. How do i get it to start up again?

    an icon with usb to itunes..what's that means?

  • [SOLVED]How to add OAL driver level functionality in the AM335x BSP source code???

    Dear developers,
    Greetings!!!
    As, my platform is WinCE 7 with AM335x BSP and I would like to copy one driver and update the driver as per my requirements. The location from where I have taken the existing driver is - 
    BSP\SRC\CSP\COMMON_TI_AMXX\OAL --
    Existing diver is OALRTC and new driver is abc_I2C under the same location and I have tailored the driver according to my requirements.
    One funciton is OALIoCtlHalInitRTC and the call is made from BSP\SRC\OAL\oallib\ioctl.c and the calling funciton is BSPIoCtlHalInitRegistry
    In my case, I am calling my OAL API as OALIoCtlHalInitPHY..
    But the thing is that I am getting linking error during the time of compiling and is shown below -
    Error 6 Error(s) in directory "C:\WINCE700\platform\AM335x\SRC\OAL\OALEXE\". C:\WINCE700\build.log 2800
    Error 7 oal.lib(ioctl.obj) : error LNK2019: unresolved external symbol OALIoCtlHalInitPHY referenced in function BSPIoCtlHalInitRegistry C:\WINCE700\build.log 2801
    Error 8 fatal error LNK1120: 1 unresolved externals {log="C:\WINCE700\build.log(2802)"} C:\WINCE700\OSDesigns\Enventure\Enventure\Wince700\AM335x_ARMV7_Retail\cesysgen\platform\AM335x\target\ARMV7\retail\oal.exe
    Error 9 NMAKE : fatal error U1077: 'C:\WINCE700\sdk\bin\i386\ARM\link.EXE' : return code '0x460' C:\WINCE700\build.log 2803
    Error 10 TargetExeFiles -nologo BUILDMSG=Stop. BUILDROOT=C:\WINCE700\platform\AM335x LINKONLY=1 NOPASS0=1 failed - rc = 2. C:\WINCE700\build.log 2805
    Error 11 BLDDEMO: ERROR: There were errors building CEBASE. C:\WINCE700\build.log 2837
    As I searched but I am unable to solve the issue. 
    Any one suggest that how to solve the issue???

    Hello Friends,
    The above problem is self solved..

  • How to read instrument driver dll files

    Hello,
    How to read .dll files of an instrument driver? What is the programming methodology followed in dll files? I will be grtaeful to you if someone can point me a way to do this.
    Thanks,
    Ananda H S

    If you can get your hands on the driver dll sdk or source code, you can use Tools --> Import --> Shared Library (.dll)... and use the wizard to easily generate the code you need to implement it.
    Bill
    (Mid-Level minion.)
    My support system ensures that I don't look totally incompetent.
    Proud to say that I've progressed beyond knowing just enough to be dangerous. I now know enough to know that I have no clue about anything at all.

  • [SOLVED] How to add modules to build with the kernel?

    Hello i´m trying to learn how to build my own custom kernel and doing it the arch way https://wiki.archlinux.org/index.php/Ke … raditional. But unfortunately dm-crypt was not included in the kernel so it all failed.
    svart_alg% sudo mkinitcpio -k 3.15.6 -c /etc/mkinitcpio.conf -g /boot/initramfs-test.img
    ==> Starting build: 3.15.6
    -> Running build hook: [base]
    -> Running build hook: [udev]
    -> Running build hook: [autodetect]
    -> Running build hook: [modconf]
    -> Running build hook: [lvm2]
    ==> ERROR: module not found: ‘dm-snapshot’
    -> Running build hook: [encrypt]
    ==> ERROR: module not found: ‘dm-crypt’
    -> Running build hook: [block]
    -> Running build hook: [filesystems]
    -> Running build hook: [keyboard]
    -> Running build hook: [fsck]
    ==> WARNING: No modules were added to the image. This is probably not what you want.
    ==> Creating gzip initcpio image: /boot/initramfs-test.img
    ==> WARNING: errors were encountered during the build. The image may not be complete.
    I have never don any of this before and have no idea of how to add a missing module to the kernel i´m building. So i search on internet and had a very hard time finding a good guide for this but i fond one possible solution. https://www.kernel.org/doc/Documentatio … odules.txt
    svart_alg% make -C /home/nigro_alko/Kernel/linux-3.15.6 M=/home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in
    make: Entering directory ‘/home/nigro_alko/Kernel/linux-3.15.6‘
    mkdir: cannot create directory ‘/home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in’: Not a directory
    scripts/Makefile.build:44: /home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in/Makefile: Not a directory
    make[1]: *** No rule to make target ‘/home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in/Makefile’. Stop.
    Makefile:1310: recipe for target ‘_module_/home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in’ failed
    make: *** [_module_/home/nigro_alko/Kernel/cryptsetup-1.6.5/Makefile.in] Error 2
    make: Leaving directory ‘/home/nigro_alko/Kernel/linux-3.15.6‘
    So is there any one that have time to help a lost little newbie i would bee very happy  :-)
    Last edited by Moosey_Linux (2014-07-29 15:00:40)

    karol wrote:Why do you want a custom kernel in the first place?
    Moosey_Linux wrote:i´m trying to learn how to build my own custom kernel
    Reason enough IMO. But anyway... you refer to the Traditional build method in the wiki, but is it possible you didn't really read it? Or maybe you only skimmed it? Did you run make menuconfig? Did you try to build everything in instead of using modules? That mkinitcpio output suggests that you did.
    As suggested there for first-timers, it's a good idea to start with a kernel configuration that is known to work - the Arch config is the obvious choice, but there are other sources e.g. http://kernel-seeds.org/ .

  • How to link a wrapper DLL to the target DLL

    I appreciate your help!
    Question:
    In my project, I need to deal with a hybrid programming of C++ and Labview. The C++ part has been encoded into a DLL, which aims to do a complex mathematics. The main function in the DLL has the following form:
                              float RateEqCalculate(class CLaserPulse *Pulse, class CMaterial *Material, class CThresh *ThreshPara, class CRateResults &r);
    The four arguments are all of the class type. The first three arguments are used to input parameters to the function and the last one is used to record the process of computation. For example: class CLaserPulse is composed by several numerics and two functions as the following form:
    class CLaserPulse
    public:
     float fDuration;  
     float fWave;  
     float fNA;   
     float fRefrIndex;                                     // Refractive Index
     float fAbsCoeff;                                     // Absorption coefficient [1/m]
     CLaserPulse();
     virtual ~CLaserPulse();
     virtual double Shape(double dTime);       // gives Temporal Shape
     float SpotDiameter();                            // Calculate Spotdiameter
    As in labview "class" cannot be accepted as an argument of the "Library Function Node" directly, a wrapper DLL is required to translate the "class" to the type labview can understand. The following link is a good illustration of this process. http://labviewwiki.org/DLL/shared_library Given the argument class CLaserPulse has been converted into the wrapper DLL by the method from the link, how can I later link this wrapper DLL to the target DLL. My understanding is like this:
                                                                                                 Target DLL
                                                                                    float RateEqCalculate(
      class CLaserPulse  ->   wrapper DLL       .........linking.........        class CLaserPulse,
      class CMaterial      ->   wrapper DLL       .........linking.........        class CMaterial,
      class CThresh        ->   wrapper DLL       .........linking.........        class CThresh ,
      class CRateResults  ->   wrapper DLL     .........linking.........        class CRateResults );
    Am I right? Four wrapper DLL to four class type arguments?
    Many thanks!!!

    Hello Rolf and Christian: 
    Thank you for your suggestions! I'm now working on it. I appreciate your continuous help!! 
    I'll briefly summarize my question here:
    In the original DLL, which is compiled by VC++ 6.0 and named RateEquation.dll, three class types (CLaserPulse, CMaterial& CThresh) are inclueded to do parameter exchanges; one class type is designed to save the calculation results(CRateResults);one main function to do the calculation and save the results as following form:  
     float RateEqCalculate(class CLaserPulse*, class CMaterial*, class CThresh*, class CRateResults &r); 
    My question now is the initialization of the struct type and the communication between this type with labview. 
    I'll take class CMaterial as an example to show how I made it into wrapper DLL.Original class CMaterial is defined as following:
    class CMaterial
    public:
     float AbsorberGap;
     float BandGap;
     float CollTime;
     float ElDensity; float RefractiveIndex; 
     float AbsorptionCoeff;  
     float MoleculeMass;  
     float Density;  
     float HeatCapacity;  
     float HeatConductivity;  float TAmbient;  
     CMaterial();
     virtual ~CMaterial();
      In a wrapper dll it's like this: 
    WrapperDll.h
     extern "C" { /*using a C compiler*/            //Using a C compiler to write the wrapper DLL
    #endif 
    struct RATEEQUATION_API CMaterial{                  
      //Electronical properties
      float AbsorberGap;
      float BandGap;
      float CollTime;
      float ElDensity;
      //Optical properties
      float RefractiveIndex;
      float AbsorptionCoeff;
      //Other properties
      float MoleculeMass;
      float Density;
      float HeatCapacity;
      float HeatConductivity;
      float TAmbient;
      typedef struct CMaterial CMaterial;                                             /* make the class opaque to the wrapper*/
     RATEEQUATION_API CMaterial* creat_CMaterial(void);           
    RATEEQUATION_API void destroy_CMaterial(CMaterial* LV_ref);
    #ifdef __cplusplus
    #endif  
    WrapperDll.cpp
    RATEEQUATION_API CMaterial* creat_CMaterial(void)
           return new CMaterial();                              
    RATEEQUATION_API void destroy_CMaterial(CMaterial* LV_ref)
           delete LV_ref;
     In function creat_CMaterial(), one can see the constructor of class CMaterial is called. As struct type CMaterial has the same memory layout as class type CMaterial, so it’s safe and possible to return a class CMaterial* to struct CMaterial* and it’s initialized by the default values in the class constructor. Now I’m confused by how one communicates between labview and struct CMaterial. For example, if I would like to change the parameter _CMaterial-> BandGap=6.5eV to 8eV. How to make it? My feeling is I need a cluster type from Labview as an input in the function creat_CMaterial:
                              CMaterial* creat_CMaterial(cluster_LV*)
    Many thanks!
    Message Edited by Kuo on 09-15-2009 09:56 AM
    Message Edited by Kuo on 09-15-2009 09:59 AM

Maybe you are looking for