Sometimes after putting my iMac to sleep, I can't get it to wake up and have to turn it off at the mains. Any ideas why?
Sometimes after putting my iMac to sleep, I cannot get it to wake up again. It's as if it's shut down and I have to turn it off at the mains and restart it. Any ideas why? Does this keep happening to anybody else?
That message means that you have to restore the iPad now. Something went wrong. You need to restore the iOS software and then restore from the backup.
Read this carefully and follow the instructions. Make sure that you restore from your backup at the end of the process. That is covered at the bottom of the support article.
http://support.apple.com/kb/HT1414
Similar Messages
-
Runninig 10.6.8 on new iMac. The last two weeks I keep loosing internet and have to turn airport off and on to restore service. This happens every time it goes into sleep mode. It is not the router as my two laptops do not have this problem. I read that in 2008 MMP's had a similar issues .Any thoughts?
Go to /Library/Preferences/System Configuration
Move all the files from the System Configuration folder to the Trash.
Restart your Mac. See if that made a difference. -
my iphone suddenly died as well. Holding the sleep button and home button together got it going again. Any ideas why this happened?
No, I don't think anyone here would know.
Mine has done that once or twice. -
when i sync my ipad and imac on ical the times are different yet the time zones are the same, any ideas why?
Under the summary tab in iTunes make sure you have Automatically Back Up This computer. If you have iCloud selected it won't back up when syncing.
-
Sometimes my MacMini won't wake up. Have to turn it off/on. What can cause this?
Sometimes my MacMini won’t wake up. Have to turn it off/on. What can cause this?
Open System Preferences > Energy Saver
Click: Restore Defaults
If that doesn't help, try Resetting the System Management Controller (SMC) -
I am using iPhone 4s. I can connect to my home wifi network but it works briefly, then whilr it shows connected with good signal strength, but I can not open a page in safari. I have to turn off the wifi and turn it on again for connection. This goes on and on. Very annoying. Please can anyone solve this problem?
Hi ,
thx for the feedback,to clarify my question :
1-i am able to connect to any wifi network in airports, public places , my home , office , etc.o to get in is no problem.
2-I can also log in into a specific website eg: was in Paris 2 days ago and could log in into the portal of a wifi provider.
3-But when i have to log in providing an e-mail address or other info , i get into a loop where i can not get into the next page but i do get always redirected to the page asking all the info.
This is not only at an airport , i do have it also with my own internet service provider , even if i want to log in from my home into their webmail site i get into this loop where after putting in all the inlog data i get that same page back every time.( i can get mail through my normal mailbox , no problems here)
I do have indeed OS 6 and it is an iPad 2.I do not have the problem with an iPhone 4 S when i use wifi and here i also do have os 6 !! -
Received SW update notice (from Apple) this morning for my 24" iMac. After it re-bootd, all that appeared is a white screen - no icons, just white. I re-booted, again - just a white screen.
Start up using your original install discs by inserting the disc and holding the C key while rebooting. Run Disk Utility to repair the drive and restart. If everything goes ok run Software Update again.
-
My Ipod Touch has been frozen for almost two weeks now. I have truning it off by useing the sleep and top button and it is still not working. I have been pluging it in my laptop and it is sycning but still did noting. What should I do?
It seems as your iOS Software Is most likely corrupt. Try doing a software restore in iTunes by clicking in your iPod and clicking the Restore button. This will restore your iPod to factory settings. So back up your Music, Videos, and purchases before restoring.
-
I put my iMac to sleep last night and today it will not power on? I have checked all cords and outlets. What's going on?
James did you find a solution? Last night my daughter put her Macbook Pro to sleep and now it won't turn on or charge? I think it is not charging because the light does not come on. We charged mine and the light came on and worked so it is clearly her computer. Help!!!
-
My Safari Icon ( Button) is missing on my iMac after I downloaded a update. How can I get the icon (Button Safari) back on my desktop and connecting again to the Internet ?...
Thanks for the helpOften when people think they've deleted an application, what's really happened is that they deleted its icon from the Dock. In the Finder, select
Go ▹ Applications
from the menu bar, or press the key combination shift-command-A to open the Applications folder. If the application is in that folder, drag it to the Dock (not to the Desktop or anywhere else.) The other Dock icons will move out of the way to make a place for it. -
New (3mo) macbook air screen goes black and sometimes won't come back on after I unplug it from the power cord. Any ideas why it is doing this? Sometimes I have to hold power button for 10 seconds for it to shut off then back on. Sometimes holding the power button for a second is enough for it to come back on.
I took it to the Genius Bar, and they identified it as a hardware issue. Just got it back today. Parts replaced were:
620-5629 Display Module — Symptom: Distored/blurred/focus video issue
605-3284 Top Case with Keyboard — Symptom: specific key(s) do not work
So far so good. I'd suggest taking it in and not trying to work around it — it's a rare hardware issue (given the number of threads about it) and should be replaced. -
My iPhone 3GS keeps turning itself off all the time the power/sleep button dosent work so it's quiet annoying having to plug it in all the time dose anyone have a fix for this?
The "fix" is to get the phone repaired. There's no magic solution for a broken phone.
Bring your phone ant $149 to Apple for an out of warranty replacement, or find a 3rd party repair shop near you. -
Iphone would not restore---- Error -50. I have tried to restore, and it restored it to the new point that it created after 5.0 was installed. How can I get it an older restore point from my backups and restore it on another computer? The phone has been wiped out. I can see earlier backups in my C:\Documents and Settings\user\Application Data\Apple Computer\MobileSync\Backup folder. There are four subfolders in this address. I need my contacts, photos, and messages back. I know this is a common error but I can not figure it out. I have ran the other troublshoot items in the error steps for 13 and 14 like apple says. Is there a way to call apple and get a step by step of how to restore from another restore point? Does anybody have a solution????
It tells you to go to Error 13 and 14 if you receive error (-50).
Here is what I have tried...
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting. I have moved it around to different ports.
Put a USB 2.0 hub between the device and the computer. Didn't change anything.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts. Removed all virus protection and firewall.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.Used the Microsoft fix it.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online. Doesn't matter.
Try to restore from another known-good computer and network. I do not know how to do this or how to find the correct/full/complete restore point. There should be more information for this. -
Do you have any ideas why Motion 5 would run slow on a computer? I have an Imac with 8Gigs of ram, and plenty of hard drive space, but it still gives me the beach ball when I add a few lights and effects. I'm at the end of my rope.
You probably don't really need 1080 at 60 for your finished projects but since you're just starting out with Motion, you need to lower your expectations. A long way. 1080 is about 2 million pixels per frame, DV is only about 400,000. That's not just five times as many pixels for the Mac to track; everything in video is exponential.
Explore the training tutorials available by Mark Spencer. You will get an idea of how his super powerful machine reacts with the software.
Adding a light roughly doubles the processing time over flat scenes. Two lights increases processing again. Reflections require processing the lights and then calculating the reflections so add another quarter of the time required for flat scenes. Add camera movement, motion blur, and depth of field and you need exponentially more processing time for every frame. The preload of renders into RAM is one of the cooler features of Motion, as comapred to After Effects, but that takes tons of time, to.
Try working in ye olde DV resolution for a few days. Get to know the software's limitations and what gets imposed by your Macintosh. Step up to 720p/30 and see how things slow down. -
After installing Mavericks my MacBook Pro and my MacMini can't shut down, only a grey screen and finish. Must be killed by the power button. Why?
Nach der Installation von Mavericks kann ich weder das MacBook Pro (2 x 2.4 GHz) noch den MacMini (2 x 2.66 GHz) herunterfahren. Es bleibt ein dauerhafter grauer Bildschirm. Nach 20 min habe ich einen erzwungenen Neustart durchgeführt.
Ausserdem startet die Macs wesentlich langsamer als mit OS X 10.6.8.same here... sometimes it works, most of the time it doesn't!!
Maybe you are looking for
-
ALV report editable to enter text and print with including the text?
Hi all, I have to display output of a report in ALV format and i have to make two fileds can be editable to enter texts by user and able to print the list with that texts . Is it possible using standard Function modules or I have to go for OO metho
-
Can we improve further this update query
Can we optimize the following query further. UPDATE OPTPRC_CHANGES_PK SET UPDATEFLAG_ = 'X' WHERE (UPDATEFLAG_ = 'U' OR UPDATEFLAG_ = 'A') AND EXISTS ( SELECT 1 FROM OPTPRC WHERE OPTPRC.DATE_ = OPTPRC_CHANGES_PK.DATE_ AND OPTPRC.EXCHCODE = OPTPRC_CHA
-
Is it possible to replace FCP software disks? If so, how?
My installation software for Final Cut Studio Pro seems to have been a casualty of a tidying up of my studio - that is it is missing and presumed to have been accidentally tossed in the trash. It is registered. Is it possible to get replacement softw
-
Problem parsing TextMessage from a JMS queue
I'm attempting to read and parse a TextMessage from a JMS queue. The message is in an XML format and I'm trying to parse it using "oraext:parseXML". If I hardcode a value such as: <copy> <from expression="'<ns:person xmlns:ns="urn:mynamespace"><ns:pe
-
Update cannot be applied for CS6 products
Hello, I ran the update for some of my products and I got these errors: Adobe Illustrator CS6 Update (version 16.0.3) There was an error downloading this update. Please quit and try again later. Error Code: U43M1U49 Dreamweaver CS6 (to version 12.0.3