SPA112 - problem with VLAN
Hello,
recently I bought few of SPA112 gateways, and I have two problems:
1. provisioning using xml file; device is not using new vlan setting (other settings such as dialplan, line number, user and passwd are working correctly), what I'm trying to apply is identical to setting used in other Sipura devices:
<!-- VLAN Settings -->
<Enable_VLAN ua="na">yes</Enable_VLAN>
<VLAN_ID ua="na">127</VLAN_ID>
Also tried with putting above setting in <router-configuration> but no luck.
2. it seems that after putting gateway from web service to use vlan, it still sits on access. This is what I see:
VID VLAN Name MAC Address Port Type
127 vlan127 88-75-56-05-98-FA 26 Dynamic
499 vlan499 88-75-56-05-98-FA 26 Dynamic
port setting is vlan499 - untagged, vlan127 - tagged. I want it to use only vlan127. Any help would be much appreciated, thanks.
FW version:
1.2.1 (004) Jul 27 2012
I managed to find how to set set vlan using xml, unfortunately it looks like this part of provisioning is broken on Cisco side.
Gateway created sample xml file in which part about vlans looks like this:
0
123 <- here is typo BTW
The part that is not working is , SPA doesn't respond to changes in this setting. is set correctly.
Similar Messages
-
A problem with vlan.dat retrieval in the RME
Hello,
the customer has LMS 3.1 and he uses RME for the backup of config files and vlan.dat files from netwrok devices. It is working fine, but he has problem with backuping vlan.dat files from the following switches: Cat2960-8TC,-24TC, Cat2960G-24TC,-48TC,-8TC and Cat3560E-24TD-E,S. I downloaded the latest packages for these devices into RME. I changed the telnet timeout value from 32s to 70s. But this issue still exist:-( The running and startup config from these switches is downloaded without any problem. Is it a bug?
Thank you
Best Regards
RomanHello,
I tried it manually and the copy is working ( i had to create empty file in the tftp directory under CSCOpx):-( The error mesage is that ssh and telnet is not available and tftp doesn't support fetching of vlan.dat. But ssh is working on the switches (the running and startup config is fetched by RME without any problem from these switches). The credentials verifications is done with OK for ssh and enable secret for these switches.
Roman -
SG-300 28P switches problem with VLAN Data and Voice, working all the time as Voice VLAN
Hi Everyone,
Thank you very much for your help in advance. I’m pulling my hair to fix the problem.
I just got the new SG-300 28P switches. My Bios ordered for me. I did not know how it runs until now... not an IOS based. I really do not know how to configure it.
I have 2 VLAN are Data and Voice.
- Data VLAN ID is 2 IP 192.168.2.X/255.255.255.0
- Voice VLAN ID is 200 IP 192.168.22.X/255.255.255.0
- I created two vlans, in switch, Data and Voice.
- On the port number 28, it is trunk by default, so I add Data vlan ID 2 tagged.
- On the port number 26, it is trunk by default, so I add Voice vlan ID 200 tagged.
- On the port number 27, I add Data vlan ID 2 tagged for Data vlan out.
- Port settings No.1
I set it up as Trunk with Data vlan 2 untagged, and 200 Tagged (voice vlan). I plugged in a phone with a pc attached. But the PC will get to the vlan 200 to get the DHCP address, but no from vlan 2. The Phone works with correct vlan ip.
- Port settings No.2
Trunk with vlan 1UP, 2T, and 200T. The phone is even worse. Would never pick up any IP from DHCP.
- Port settings No.3
Access with 200U...of course the phone will work... and the PC could not get to its own vlan. Instead, the PC got an ip from the voice vlan. Not from VLAN 2.
I have Linksys phone I’m not sure if this help.
For more information I setup in switch,
- enable voice vlan
- set the port on auto voice vlan
- enable LLDP-MED globally
- create a network policy to assign VLAN 200
- assign this network policy to the port the phone is connected to.
I hope this information help to help me to setup Data and Voice vlans, to plug the phone to work with vlan Voice 200 (IP rang 192.168.22.X), from phone to Pc and pc work as Data vlan 2 (IP rang 192.168.2.X).I just got done setting up voice VLANs on an SF 300-24P and verified working. This was working with Cisco 7900 series phones connected to a Cisco UC setup.
Here's my sample config.
Note that I edited this by hand before posting, so doing a flat out tftp restore probably won't work. However, this should give you a clue. Also, don't take this as 100% accurate or correct. I've only been working with these things for about a week, though I've worked with the older Linksys SRW switches for a couple of years. I'm a CCNP/CCDP.
VLAN 199 is my management VLAN and is the native VLAN on 802.1q trunks.
VLAN 149 is the data/computer VLAN here.
VLAN 111 is the voice/phone VLAN here.
VLAN 107 does nothing.
interface range ethernet e(1-24)
port storm-control broadcast enable
exit
interface ethernet e1
port storm-control include-multicast
exit
interface ethernet e2
port storm-control include-multicast
exit
interface ethernet e3
port storm-control include-multicast
exit
interface ethernet e4
port storm-control include-multicast
exit
interface ethernet e5
port storm-control include-multicast
exit
interface ethernet e6
port storm-control include-multicast
exit
interface ethernet e7
port storm-control include-multicast
exit
interface ethernet e8
port storm-control include-multicast
exit
interface ethernet e9
port storm-control include-multicast
exit
interface ethernet e10
port storm-control include-multicast
exit
interface ethernet e11
port storm-control include-multicast
exit
interface ethernet e12
port storm-control include-multicast
exit
interface ethernet e13
port storm-control include-multicast
exit
interface ethernet e14
port storm-control include-multicast
exit
interface ethernet e15
port storm-control include-multicast
exit
interface ethernet e16
port storm-control include-multicast
exit
interface ethernet e17
port storm-control include-multicast
exit
interface ethernet e18
port storm-control include-multicast
exit
interface ethernet e19
port storm-control include-multicast
exit
interface ethernet e20
port storm-control include-multicast
exit
interface ethernet e21
port storm-control include-multicast
exit
interface ethernet e22
port storm-control include-multicast
exit
interface ethernet e23
port storm-control include-multicast
exit
interface ethernet e24
port storm-control include-multicast
exit
interface range ethernet g(1-4)
description "Uplink trunk"
exit
interface range ethernet g(1-4)
switchport default-vlan tagged
exit
interface range ethernet e(21-24)
switchport mode access
exit
vlan database
vlan 107,111,149,199
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 107
exit
interface range ethernet e(21-24)
switchport access vlan 111
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 111
exit
interface range ethernet e(1-20)
switchport trunk native vlan 149
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 149
exit
interface range ethernet g(1-4)
switchport trunk native vlan 199
exit
voice vlan aging-timeout 5
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
voice vlan oui-table add 108ccf MyCiscoIPPhones1
voice vlan oui-table add 40f4ec MyCiscoIPPhones2
voice vlan oui-table add 8cb64f MyCiscoIPPhones3
voice vlan id 111
voice vlan cos 6 remark
interface ethernet e1
voice vlan enable
exit
interface ethernet e1
voice vlan cos mode all
exit
interface ethernet e2
voice vlan enable
exit
interface ethernet e2
voice vlan cos mode all
exit
interface ethernet e3
voice vlan enable
exit
interface ethernet e3
voice vlan cos mode all
exit
interface ethernet e4
voice vlan enable
exit
interface ethernet e4
voice vlan cos mode all
exit
interface ethernet e5
voice vlan enable
exit
interface ethernet e5
voice vlan cos mode all
exit
interface ethernet e6
voice vlan enable
exit
interface ethernet e6
voice vlan cos mode all
exit
interface ethernet e7
voice vlan enable
exit
interface ethernet e7
voice vlan cos mode all
exit
interface ethernet e8
voice vlan enable
exit
interface ethernet e8
voice vlan cos mode all
exit
interface ethernet e9
voice vlan enable
exit
interface ethernet e9
voice vlan cos mode all
exit
interface ethernet e10
voice vlan enable
exit
interface ethernet e10
voice vlan cos mode all
exit
interface ethernet e11
voice vlan enable
exit
interface ethernet e11
voice vlan cos mode all
exit
interface ethernet e12
voice vlan enable
exit
interface ethernet e12
voice vlan cos mode all
exit
interface ethernet e13
voice vlan enable
exit
interface ethernet e13
voice vlan cos mode all
exit
interface ethernet e14
voice vlan enable
exit
interface ethernet e14
voice vlan cos mode all
exit
interface ethernet e15
voice vlan enable
exit
interface ethernet e15
voice vlan cos mode all
exit
interface ethernet e16
voice vlan enable
exit
interface ethernet e16
voice vlan cos mode all
exit
interface ethernet e17
voice vlan enable
exit
interface ethernet e17
voice vlan cos mode all
exit
interface ethernet e18
voice vlan enable
exit
interface ethernet e18
voice vlan cos mode all
exit
interface ethernet e19
voice vlan enable
exit
interface ethernet e19
voice vlan cos mode all
exit
interface ethernet e20
voice vlan enable
exit
interface ethernet e20
voice vlan cos mode all
exit
interface ethernet e1
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e2
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e3
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e4
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e5
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e6
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e7
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e8
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e9
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e10
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e11
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e12
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e13
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e14
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e15
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e16
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e17
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e18
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e19
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e20
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e21
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e22
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e23
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e24
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g1
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g2
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g3
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g4
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e1
lldp med notifications topology-change enable
exit
interface ethernet e2
lldp med notifications topology-change enable
exit
interface ethernet e3
lldp med notifications topology-change enable
exit
interface ethernet e4
lldp med notifications topology-change enable
exit
interface ethernet e5
lldp med notifications topology-change enable
exit
interface ethernet e6
lldp med notifications topology-change enable
exit
interface ethernet e7
lldp med notifications topology-change enable
exit
interface ethernet e8
lldp med notifications topology-change enable
exit
interface ethernet e9
lldp med notifications topology-change enable
exit
interface ethernet e10
lldp med notifications topology-change enable
exit
interface ethernet e11
lldp med notifications topology-change enable
exit
interface ethernet e12
lldp med notifications topology-change enable
exit
interface ethernet e13
lldp med notifications topology-change enable
exit
interface ethernet e14
lldp med notifications topology-change enable
exit
interface ethernet e15
lldp med notifications topology-change enable
exit
interface ethernet e16
lldp med notifications topology-change enable
exit
interface ethernet e17
lldp med notifications topology-change enable
exit
interface ethernet e18
lldp med notifications topology-change enable
exit
interface ethernet e19
lldp med notifications topology-change enable
exit
interface ethernet e20
lldp med notifications topology-change enable
exit
interface ethernet e21
lldp med notifications topology-change enable
exit
interface ethernet e22
lldp med notifications topology-change enable
exit
interface ethernet e1
lldp med enable network-policy poe-pse
exit
interface ethernet e2
lldp med enable network-policy poe-pse
exit
interface ethernet e3
lldp med enable network-policy poe-pse
exit
interface ethernet e4
lldp med enable network-policy poe-pse
exit
interface ethernet e5
lldp med enable network-policy poe-pse
exit
interface ethernet e6
lldp med enable network-policy poe-pse
exit
interface ethernet e7
lldp med enable network-policy poe-pse
exit
interface ethernet e8
lldp med enable network-policy poe-pse
exit
interface ethernet e9
lldp med enable network-policy poe-pse
exit
interface ethernet e10
lldp med enable network-policy poe-pse
exit
interface ethernet e11
lldp med enable network-policy poe-pse
exit
interface ethernet e12
lldp med enable network-policy poe-pse
exit
interface ethernet e13
lldp med enable network-policy poe-pse
exit
interface ethernet e14
lldp med enable network-policy poe-pse
exit
interface ethernet e15
lldp med enable network-policy poe-pse
exit
interface ethernet e16
lldp med enable network-policy poe-pse
exit
interface ethernet e17
lldp med enable network-policy poe-pse
exit
interface ethernet e18
lldp med enable network-policy poe-pse
exit
interface ethernet e19
lldp med enable network-policy poe-pse
exit
interface ethernet e20
lldp med enable network-policy poe-pse
exit
interface ethernet e21
lldp med enable network-policy poe-pse
exit
interface ethernet e22
lldp med enable network-policy poe-pse
exit
lldp med network-policy 1 voice vlan 111 vlan-type tagged
interface range ethernet e(1-22)
lldp med network-policy add 1
exit
interface vlan 199
ip address 199.16.30.77 255.255.255.0
exit
ip default-gateway 199.16.30.3
interface vlan 1
no ip address dhcp
exit
no bonjour enable
bonjour service enable csco-sb
bonjour service enable http
bonjour service enable https
bonjour service enable ssh
bonjour service enable telnet
hostname psw1
line console
exec-timeout 30
exit
line ssh
exec-timeout 30
exit
line telnet
exec-timeout 30
exit
management access-list Management1
permit ip-source 10.22.5.5 mask 255.255.255.0
exit
logging 199.16.31.33 severity debugging description mysysloghost
aaa authentication enable Console local
aaa authentication enable SSH tacacs local
aaa authentication enable Telnet local
ip http authentication tacacs local
ip https authentication tacacs local
aaa authentication login Console local
aaa authentication login SSH tacacs local
aaa authentication login Telnet local
line telnet
login authentication Telnet
enable authentication Telnet
password admin
exit
line ssh
login authentication SSH
enable authentication SSH
password admin
exit
line console
login authentication Console
enable authentication Console
password admin
exit
username admin password admin level 15
power inline usage-threshold 90
power inline traps enable
ip ssh server
snmp-server location in-the-closet
snmp-server contact [email protected]
ip http exec-timeout 30
ip https server
ip https exec-timeout 30
tacacs-server host 1.2.3.4 key spaceballz timeout 3 priority 10
clock timezone -7
clock source sntp
sntp unicast client enable
sntp unicast client poll
sntp server 199.16.30.1
sntp server 199.16.30.2
ip domain-name mydomain.com
ip name-server 199.16.5.12 199.16.5.13
ip telnet server -
Problems with vlan and dot1q trunking port
Dear Folks,
i have problems with my AccessPoint Konfiguration.
Even when i set the Catalyst Port to trunk, i can only connect to VLAN 1 but not to VLAN 10.
and if i change the port to statik vlan 10 i can not connect to the ap but it works...
config below:
User Access Verification
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname 1200_PP_1
logging queue-limit 100
enable secret xxxx
clock timezone A 1
ip subnet-zero
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid DEPACNGLW0HS
vlan 10
authentication shared
infrastructure-ssid
mobility network-id 10
speed basic-1.0 2.0 5.5 11.0
rts threshold 2312
channel 2412
antenna receive right
antenna transmit right
station-role root
interface Dot11Radio0.1
no ip route-cache
interface Dot11Radio0.10
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 port-protected
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
ntp broadcast client
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.2.2.222 255.255.255.0
no ip route-cache
ip default-gateway 10.2.2.2
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/122-15.JA/1100
ip radius source-interface BVI1
bridge 1 route ip
line con 0
line vty 0 4
login local
line vty 5 15
login
end
it would be fine if anyone could help me....You configure Layer 3 Mobility with WLSM. No trunking is required on the CAT switch. However, you need to set the switch port on the CAT switch as access port in VLAN 10.
Please post the WLSM and SUP720 configuration. Also, which VLAN do you want to access the AP?
The following URL may be useful for you to verify the configuration:
http://www.cisco.com/en/US/partner/products/hw/wireless/ps430/prod_technical_reference09186a00802a86a7.html -
Cisco/Linksys SLM224G SWITCH: Problem with VLANs
Hi!
I'm trying to set up VLANs in my racks. I have some knowledge about VLANs, but I still can't set it up in my way.
My situation:
I have PC which contains two virtual machines, which has to works as a routers between three networks: LAN1, LAN2, WAN. It's a bit complicated, but I'll try to draw it:
|-------------|
|----------------------------| | e1|-to-eth1-VM2-----WAN
|VirtualMachine 1 eth0|---trunk-VLAN1&2---|g1 e2|-to-eth0-VM2-----LAN2
|eth0=VLAN1 eth1=VLAN2 | | e3|-to-eth0-VM2-----LAN2 etc.
| PC | | SWITCH e4|
|VirtualMachine 2 | | e5|-to-eth1-VM1---wire-to-LAN2
|eth0=VLAN3 eth1=VLAN4 eth1|---trunk-VLAN3&4---|g2 e6|-to-eth0-VM1-----LAN1
|----------------------------| | e7|-to-eth0-VM1-----LAN1 etc.
|-------------|
gX = Gigabit ports
eX = 100Mbit ports
VMX = Virtual machine number
wire-to = patch-cord connection between ports on the switch
Schema of routing and logical visibility:
LAN1---VM1-----VM2---WAN
|
LAN2----------|
Important note is that LAN1 and LAN2 has to be separated (visible only through routers). WAN has to be visible only through VM2 for LAN2 and through by VM1 and VM2 for LAN1. It looks easy, but VLANs which I done on that switch seems to doesn't works.
I'm doing this like that:
Step1: VLAN Management / Create VLAN...
Creating VLANs from 1, 2, 3, 4 (numbers doesn't meters right now - I now that number 1 is restricted at the switch).
Step2: VLAN Management / Port to VLAN...
Setting up VLAN1 with ports g1, e5 (both tagged or untagged? - I haven't seen difference)
Setting up VLAN2 with ports g1, e6, e7, etc...
Setting up VLAN3 with ports g2, e2, e3, etc...
Setting up VLAN4 with ports g2, e1
Step3: VLAN Management / Port Setting...
Setting up port e1 to PVID4 (frame type=all I suppose, but what with "ingress filtering"?)
Setting up port e2 to PVID3
Setting up port e3 to PVID3
etc...
Setting up port e5 to PVID1
Setting up port e6 to PVID2
Setting up port e7 to PVID2
etc...
So, on that configuration and on that switch it doesn't work for me
I know that switch is seeing MACs from VLANs which are done by PC's, because when I get in "Admin / Dynamic Address" I can see MACs on correct ports and with correct VLAN ID. So the problem is to forward VLANs on their ports, next clear frames from IDs and let packets go (and back: take clear packets, add VLAN ID and send to gigabits ports).
Showed configuration is the one of many that I tried :/ but I think this one is the best one.
Or maybe I don't know VLANs as I think and that schema is impossible? Please tell me if I' doing sth wrong.
Regards
and waiting for any suggestions,
LucasYou need to make sure that your VirtualMachine can send tagged frames if the VMs share physical ethernet ports on the host.
I count 4 different LAN segments but you have only 2 physical ports on your PC (router).
And VM2 requires 3 physical connections according to the list below.
Depending on the virtualisation software you can maybe create the connection PVM1 to VM2 internally inside the PC (logical connection)
Are these the connections you require ?
VM1 --- LAN1
VM1 --- VM2
VM2 --- WAN
LAN2 --- VM2
Is this correct ? Will your PC, Virtualisation Software/Hypervisor tag frames with VLAn tags ?
If this is true I can help you configure the switch.
Jo -
Problem with VLAN Trunking within RHEL6.6 VM on Hyper-V 2012 R2?
Hello,
I'm wondering if there is a known issue with using a "trunk" mode interface within a RHEL6.6 VM? I found the following article:
https://technet.microsoft.com/en-us/library/dn531026.aspx
Where note 1 reads:
"For this specific RHEL/CentOS release, VLAN tagging may not work when used in conjunction with trunk mode".
I've been fighting with this for the better part of a day and can't figure out what I'm doing wrong. I have a RHEL 6.6 VM with two NICs. The first NIC is a standard access mode NIC - no problems there.
The second NIC has been set up as follows (via PowerShell):
$a=Get-VmNetworkAdapter -VMName "My VM"
Set-VMNetworkAdapterVlan -Trunk -VmNetworkAdapter $a[1] -AllowedVlanIdList 101-105 -NativeVlanId 1
Note that the physical switch and switchports are configured to send tagged packets for these VLANs as well.
I then set up a VLAN (eth1.102) based interface in the VM ... and never receive any traffic on it.
What I've observed is that:
A VM on the same physical host using the same virtual switch can communicate with the VM on the tagged VLAN
A pcap of the "eth1" interface (to which eth1.102 is bound) shows traffic for VLANs 101 through 105 arriving ... I just never see the traffic for VLAN 102 forwarded to the eth1.102 interface
An identical network configuration using Ubuntu 14.04.01 LTS works exactly as expected
It's this last point that has me wondering if the problem is with RHEL and not Hyper-V (or the physical/virtual switches involved).
I'm curious if anybody else has seen this behavior or, if RHEL 6.x is working for you, if you're using Intel or Broadcom NICs on the physical Hyper-V host?
Thanks,This is indeed a known issue with RHEL. There's a bug open with Red Hat on the issue, and our understanding is that they have a fix in progress that will be part of a RHEL 6.6 update. You might inquire with Red Hat regarding
their bugzilla #1135347.
Michael Kelley, Lead Program Manager, Open Source Technology Center -
LGS308 problem with vlan and multicast
Hello,
I have a LGS308 smart switch and am having problems putting multicast traffic on a specific vlan.
The switch is connected to a PC for management (vlan 1).
All ports are in acces mode, vlan 1 untagged.
I created vlan 2 and put it untagged on port 7 and 8.
Now, when I connect a multicast device (IPTV) on port 8, the switch becomes unresponsive and nothing works.
It seems the switch is flooded with multicast traffic.
Simply turning IGMP snooping on didn't help so I think it needs more configuration.
Is this a known problem?
ps: Once I have this simple setup running I'm planning for a more advanced setup with trunking 2 vlans (iptv + internet) to another switch over a single UTP cable. But first things firstYes it should!
I have changed the setup like this:
Switch 1
port 1 - access mode - vlan 1U <---> Internet
port 2 - access mode - vlan 1U <---> PC
port 7 - access mode - vlan 2U <---> IPTV source (IGMP)
port 8 - trunk mode - vlan 1T + 2T <---> switch 2 port 8
Switch 2
port 7 - access mode - vlan 2U <---> IPTV source (IGMP)
port 8 - trunk mode - vlan 1T + 2T <---> switch 2 port 8
With this setup, I can reach both switches from my PC.
However, multicast doesn't work. I don't get IPTV on switch 2 port 7. -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
Bridging problem with multiple vlans
Hello Everyone, I am using two 1310 bridges in a root / non-root setup. The switches on both sides of the wireless bridge were setup to trunk native vlan 253. Each wireless bridge also had vlan 253 setup as a Radio and Ethernet Interface. In this config, the wireless bridges could associate and ping each other, but the switches on each side could not ping each other?s management vlan interface (Vlan 25). The only way to get traffic to pass to the corresponding switches on each side of the wireless bridge was to use vlan 253 for everything. We also see this problem with some of our other 1310 bridge connections at other plants. Has anyone seen this problem or a similar problem before?
Hi Craig,
Er, dunno if you have any insight on my issue. I'm trying to get 2 AP1231s (12.3-8) in bridge mode (root/non-root, antennas transmit/receive right) that have 4 VLANs going across the airwaves. Now, the bridges are associated, they can see each other's IP address, but will they ping? Absolutely not! VLAN20 is the native assigned to bridge-group 1, I've tried IP addresses on the BVI1, dot11Radio 0.20 and fa0.20 interfaces with no luck. There's no other fancy configuration options applied, just 4 VLANs going across two associated bridges. Any ideas? Appreciate any assistance you can offer.
I'd already found the document that Rob recommended beforehand and that proved useful in getting the units to associate. Now I just need a ping! A PC connected to the non-root bridge's Ethernet port via a Xover cable is able to ping the non-root bridge but that's as far as it goes.
Root bridge config attached. No IP assigned on this copy but as advised, tried a few scenarios!
Thanks, Paul -
I'm having problem with a setup with multiple SRW2048 connected together. However, I can see the problem when simplifying my setup and using only two SRW2048 together.
The first SRW2048 receives one connection from many different servers and sends these connections to many other SRW2048. I have configured one VLAN (untagged) per server for this switch. The goal is instead of having 4 switches to do this job, I am using only one.
The second SRW2048 receives the server connections from the other switch. It then distributes these connections to various ports. I use a different VLANs on this switch to group these connections and the server uplink together).
Everything works fine until a plug the two switches together (i.e. I can verify the VLAN connections are working by connecting directly to each switch). However, when both switches are connected, I get a flooding of all interfaces (like there is a bypass of the VLANs or a loop in the connections). This happens as soon as I have two servers connected. If I connect only one, there is no problem.
If I connect a second server through a dumb switch instead of the first SRW2048, everything works fine, so I don't think that there is a loop. The problem seems to be with the VLANs (how they "cascade" together). Anybody got an idea of what the problem is?
For those who need a better visual representation:
Server1->Port 1-8 Switch1 (VLAN1 on these ports)->Port 1 (and others) Switch2 (VLAN10 on these ports)
Server2->Port 9-16 Switch1 (VLAN2 on these ports)->Port 2 (and others) Switch2 (VLAN11 on these ports)
Etc for other servers...
All VLANs are using the default settings from the Web Interfaces on the switches (Access mode, Untagged, other ports Excluded, etc.)1. The SRW switches are standalone devices. Unlike more expensive switches like those from the Cisco Small Business Pro series they don't automatically recognize each other and configure themselves to play nicely together.
2. Generally, if you create a new VLAN on one SRW you have to create the same VLAN on all other switches and also add these to the trunks connecting the switches. Same applies to the ASA if you connect the SRWs to ASA. As long as a switch is not configured for a particular VLAN it won't accept traffic for it.
3. The only thing that you may try is GVRP. I never tried this but I think it may do what you want: add a VLAN on a single switch and then propagate this to the trunks and other switches. I can't tell how well this works and whether the ASA will accept that, too. -
Problems with IP Phones registration to CUCME on SG200-50P
Problems with IP Phones registration to CUCME on SG200-50P
System setup:
- Router Cisco 2811 with IOS 12.4(24)T5 Advanced IP Services, CUCME 7.1, DHCP Server
with HWIC-4ESW
- Switches:
- old - SLM224P
- new - SG200-50P (SLM2048PT), OS v1.3.2.02
- IP Phones 7911 and 7931, OS v8.4.2
One VLAN (for desktops and IP Phones) and one IP subnet, no voice VLAN.
Network diagram:
C2811---HWIC-4ESW---SWITCH---IPPhones
Problem description:
1. In the old setup with SLM224P everything works fine.
Connected phones almost immediately (1-2 sec. after power up) get ip address, configuration and registers to CUCME.
2. When switch is changed to new SG200-50G:
- ip phones get their ip address and tftp configuration very slowly - about 10-20 seconds
- ip phones cant register to CUCME at all. On the router with SCCP debugging turned on there is no sing of registration attempt
- after reconnecting the old SLM224P situation backs to normal
Things that have been checked or tried without success:
- ports speed and duplex auto, correct detection - although not tested with manual settings
- CDP/LLDP on/off
- smartport mode auto and most static settings, also with disabled smartport
- power cycle / reset
- spanning tree and port security settings
- solutions from that post - https://supportforums.cisco.com/thread/2232161
None of the above methods worked.
The only action that allowed ip phones to register was changing smartport role to static IPPhone + Desktop.
After that when phone was disconnected and then reconnected the problem exists again - no registration (IP Phone status DECEASED in CUCME). Same with power cycle/reset.
Please advice.
Thanks in advance.1 - You have created the voice vlan?
Nope, flat network, one ip subnet (10 hosts and 10 phones)
2 - Have you set a phone on an untagged access port for the voice vlan to see if it works?
Yep, phones are connected to untagged access ports of the one and only vlan
3 - Have you tried to set the auto voice vlan on the switch so it dynamically assigns the role for ip phone + desktop?
Not sure about auto voice vlan setting, although there was no triggers to AVV - no static voice vlan, no CDP/VSDP advertisements of voice vlan.
We've tested static and auto smartport roles (independently of auto voice vlan feature) with successful auto-detection.
The switch was pretty much in default out-of-the-box config (beside management parameters).
4 - When rebooting the switch, you did ensure to save the start up to running config?
Yes, running to startup
5 - Have you manually set spanning tree PORT FAST for the phone ports?
No, we haven't tested that. But portfast should be set automatically for the desktop and ip phone smartport roles. -
Cisco ASA 5505 - problem with negotiating IP address from PPPoE
Hi all,
I have problem with negotiating IP address from PPPoE. There is following design: ISP providing vDSL ending on VDSL modem in bridge mode. Behind brigde modem is ASA 5505 terminting PPPoE on OUTSIDE. Everything works fine except negotiating IP address from PPPoE server.
I have configured ASA 5505 with (ASA Version 9.2(2)4) for PPPoE like this [1.]. But If i try to "show" IP address on OUTSIDE interface a get this [2.], ok strange but let's continue. If list "show vpdn pppinterface id 1" i get this [3.]. Seems that I got public IP addres what was right, but this IP address was not associated with interface OUTSIDE?
Well, if I set IP address manually like this [4.] and also set a default route everything works fine but what will happen when ISP change reservation for my IP address or default gateway.
I have tried different version of ASA OS like 8.4, 9.1 but without luck.
Can anybody help me. Thanks a lot.
Regards
Karel
[1.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address pppoe setroute
vpdn group O2 request dialout pppoe
vpdn group O2 localname O2
vpdn group O2 ppp authentication chap
vpdn username O2 password *****
interface Ethernet0/0
description >>uplink O2 vDSL<<
switchport access vlan 100
[2.]
ciscoasa(config-if)# show ip address vlan 100 pppoe
ciscoasa(config-if)# 0.0.0.0 255.255.255.255 on Interface: OUTSIDE
ciscoasa(config-if)# show interface vlan 100 detail
Interface Vlan2 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1492
IP address unassigned
Traffic Statistics for "OUTSIDE":
28 packets input, 1307 bytes
31 packets output, 721 bytes
0 packets dropped
1 minute input rate 0 pkts/sec, 3 bytes/sec
1 minute output rate 0 pkts/sec, 1 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 15
Interface config status is active
Interface state is active
[3.]
ciscoasa(config-if)# show vpdn pppinterface id 1
PPP virtual interface id = 1
PPP authentication protocol is CHAP
Server ip address is 88.103.200.41
Our ip address is 85.71.188.158
Transmitted Pkts: 20, Received Pkts: 16, Error Pkts: 0
MPPE key strength is None
MPPE_Encrypt_Pkts: 0, MPPE_Encrypt_Bytes: 0
MPPE_Decrypt_Pkts: 0, MPPE_Decrypt_Bytes: 0
Rcvd_Out_Of_Seq_MPPE_Pkts: 0
ciscoasa(config-if)# show vpdn session state
%No active L2TP tunnels
%No active PPTP tunnels
PPPoE Session Information (Total tunnels=1 sessions=1)
SessID TunID Intf State Last Chg
22298 2 OUTSIDE SESSION_UP 561 secs
[4.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address 85.71.188.158 255.255.255.255 pppoe setroute
route OUTSIDE 0.0.0.0 0.0.0.0 88.103.200.41 1You're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
HELP!! asa 5505 8.4(5) problem with port forwarding-smtp
Hi I am having a big problem with port forwarding on my asa. I am trying to forward smtp through the asa to my mail server.
my mail server ip is 10.0.0.2 and my outside interface is 80.80.80.80 , the ASA is setup with pppoe (I get internet access no problem and that seems fine)
When I run a trace i get "(ACL-Drop) - flow is deied by configured rule"
below is my config file , any help would be appreciated
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISPDsl
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_SMTP
host 10.0.0.2
access-list outside_access_in extended permit tcp any object server_SMTP eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network server_SMTP
nat (inside,outside) static interface service tcp smtp smtp
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c5570d7ddffd46c528a76e515e65f366
: endHi Jennifer
I have removed that nat line as suggested but still no joy.
here is my current config
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISP
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_Mail
host 10.0.0.2
access-list outside_access_in extended permit tcp any object Server_Mail eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network Server_Mail
nat (inside,outside) static interface service tcp smtp smtp
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f3bd954d1f9499595aab4f9da8c15795
: end
also here is the packet trace
and my acl
Thanks -
Cisco ASA 5505 - problem with ssh, icmp on OUTSIDE interface
Hi all,
I have a very strange problem with OUTSIDE interface and remote ssh. Well, I have followed documentation and configure remote access for ssh like this [1.]. If I want to connect from internet to OUTSIDE interface [2.] get no response and in log I can see this message [3.]. I really do not understand why is ssh connection dropped by OUTSIDE access-list [4.]? If I understand documentation correctly there is no impact for remote mangement/access like icmp, ssh, http(s) by interface access-list. So, why?
When I try ssh connection form internal network to INSIDE interface everything works fine and I can log in to ASA. If I try allow ssh in OUTSIDE access-list still no success and a get this message [5.]? It is strange, isn't?
The same problem with icmp if I want to "ping" OUTSIDE interface from internet a get thish message in log [6.] and configuration for ICMP like this [7.].
Full ASA config is in attachment.
Can anybody help how to fix it and explain what is exactly wrong.Thanks.
Regards,
Karel
[1.]
ssh stricthostkeycheck
ssh 10.0.0.0 255.255.255.0 INSIDE
ssh 0.0.0.0 0.0.0.0 OUTSIDE
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
ASA-FW01# show ssh
Timeout: 60 minutes
Version allowed: 2
10.0.0.0 255.255.255.0 INSIDE
0.0.0.0 0.0.0.0 OUTSIDE
[2.]
ASA-FW01# show nameif
Interface Name Security
Vlan10 INSIDE 100
Vlan20 EXT-VLAN20 0
Vlan30 EXT-WIFI-VLAN30 10
Vlan100 OUTSIDE 0
ASA-FW01# show ip
System IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
Current IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
ASA-FW01# show interface OUTSIDE detail
Interface Vlan100 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1480
IP address 85.71.188.158, subnet mask 255.255.255.255
Traffic Statistics for "OUTSIDE":
90008 packets input, 10328084 bytes
60609 packets output, 13240078 bytes
1213 packets dropped
1 minute input rate 15 pkts/sec, 994 bytes/sec
[3.]
Jan 13 2015 06:45:30 ASA-FW01 : %ASA-6-106100: access-list OUTSIDE denied tcp OUTSIDE/193.86.236.70(46085) -> OUTSIDE/85.71.188.158(22) hit-cnt 1 first hit [0xb74026ad, 0x0]
[4.]
access-list OUTSIDE remark =======================================================================================
access-list OUTSIDE extended permit icmp any any echo-reply
access-list OUTSIDE extended deny ip any any log
access-group OUTSIDE in interface OUTSIDE
[5.]
Jan 12 2015 23:00:46 ASA-FW01 : %ASA-2-106016: Deny IP spoof from (193.86.236.70) to 85.71.188.158 on interface OUTSIDE
[6.]
Jan 13 2015 06:51:16 ASA-FW01 : %ASA-4-400014: IDS:2004 ICMP echo request from 193.86.236.70 to 85.71.188.158 on interface OUTSIDE
[7.]
icmp unreachable rate-limit 1 burst-size 1
icmp permit 10.0.0.0 255.0.0.0 INSIDE
icmp permit 10.0.0.0 255.0.0.0 EXT-WIFI-VLAN30
icmp permit any OUTSIDEYou're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
Hi *,
I have the following problem with RADIUS and EAP authentication.
Radius server sends an "Access-Accept" packet to my AP, but the station does not authenticate.
I've tried with different encryption configuration and with different authentication methods under "dot11 essid", but nothing changes...
What could it be?
Debug piece and configuration follows:
*Jan 25 14:23:34.795: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.795: RADIUS(00000012): sending*Jan 25 14:23:34.799: RADIUS: 4E 47 56 7A 78 65 4A 4F 55 31 47 40 77 6C 61 6E [NGVzxeJOU1G@wlan]*Jan 25 14:23:34.799: RADIUS: 2E 6D 6E 63 30 30 31 2E 6D 63 63 30 30 31 2E 33 [.mnc001.mcc001.3]*Jan 25 14:23:34.799: RADIUS: 67 70 70 6E 65 74 77 6F 72 6B 2E 6F 72 67 [gppnetwork.org]*Jan 25 14:23:34.799: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.799: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.799: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.799: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:34.811: RADIUS/DECODE: EAP-Message fragments, 20, total 20 bytes*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:34.831: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:34.831: RADIUS: 32 [2]*Jan 25 14:23:34.831: RADIUS(00000012): Config NAS IP: 192.168.173.2*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.835: RADIUS(00000012): sending*Jan 25 14:23:34.835: RADIUS: 10 01 00 01 07 05 00 00 D9 37 C3 D9 79 3E 33 EA [?????????7??y>3?]*Jan 25 14:23:34.835: RADIUS: F3 7D 73 43 BF BA D0 6A [?}sC???j]*Jan 25 14:23:34.835: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.835: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.835: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.835: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.035: RADIUS: Received from id 1645/64 192.168.177.158:1812, Access-Challenge, len 304*Jan 25 14:23:35.039: RADIUS: 46 10 78 5F 5F B0 CB 6C 0B 05 00 00 DA C3 BF 28 [F?x__??l???????(]*Jan 25 14:23:35.039: RADIUS: E0 18 2B 95 97 C2 0A D7 40 53 FE 62 [??+?????@S?b]*Jan 25 14:23:35.039: RADIUS(00000012): Received from id 1645/64*Jan 25 14:23:35.039: RADIUS/DECODE: EAP-Message fragments, 60+220, total 280 bytes*Jan 25 14:23:35.355: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:35.359: RADIUS: 92 DA 5E 26 CF 40 01 22 7A 8E F5 C1 [??^&?@?"z???]*Jan 25 14:23:35.359: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:35.359: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:35.359: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:35.359: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.367: RADIUS: Received from id 1645/65 192.168.177.158:1812, Access-Accept, len 30*Jan 25 14:23:35.367: RADIUS: authenticator 8C 2C 1B 97 82 BB 6C 7F - AA D3 4A AB CA 22 8B B7*Jan 25 14:23:35.367: RADIUS: EAP-Message [79] 10 *Jan 25 14:23:35.367: RADIUS: 03 01 00 04 00 00 00 00 [????????]*Jan 25 14:23:35.371: RADIUS(00000012): Received from id 1645/65*Jan 25 14:23:35.371: RADIUS/DECODE: EAP-Message fragments, 8, total 8 bytes*Jan 25 14:23:35.671: %DOT11-7-AUTH_FAILED: Station d023.dbb8.d6a9 Authentication failed
Config:
aaa new-model!aaa group server radius rad_eap server-private 192.168.177.158 auth-port 1812 acct-port 1813 key 7 044803071D2448!aaa authentication login eap_methods group rad_eapaaa authorization exec default if-authenticated aaa authorization network default if-authenticated ! aaa session-id commonip name-server 192.168.177.45! dot11 ssid WifiEAP1 vlan 10 authentication open eap eap_methods authentication shared eap eap_methods authentication key-management wpa optional guest-mode! bridge irb! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 10 mode ciphers aes-ccm tkip wep128 ! broadcast-key vlan 10 change 300 ! ssid WifiEAP1 ! antenna gain 0 station-role root! interface Dot11Radio0.10 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled! interface GigabitEthernet0 ip address 192.168.173.3 255.255.255.0 no ip route-cache! interface GigabitEthernet0.1 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled! interface BVI1 ip address 192.168.173.2 255.255.255.0 no ip route-cache!ip radius source-interface BVI1 bridge 1 route ip
thanks so much!Stefano: not sure if related but there is an unsupported attribute in the debugs:
Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr:
*Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41
*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface
Try to eliminate any configured attributes on radius except those in IETF radius. Then try again.
You may also chech by removing the shared eap as suggested above. Let us know if this works.
Sent from Cisco Technical Support iPad App
Maybe you are looking for
-
I can open and read my email but can not open any links
I Can open my email but can not open any links
-
Hi All, I got a problem here. Exchange rate is being picked up without decimals example USD doc. currency , INR local currency exchange rate being picked up in a report is INR 3900 where as i want INR 39.00 Please help Thanks, Prashanth
-
HI major diffrence in select-options and parameters
Hi, Can any one explain me the major diffrence between select options and parameters. I know that in select options we can give a range of values and in parameter one value. Thanks
-
Add a Data Action to Execute a Method - Problem
Hi, I'm working with JDeveloper 10.1.3 - JSP,Struts and ADF BC. I have a method that retruns 2 values (audit(Number,Number)) and exposed the Service Metod, but now I need to add a Data Action to Execute that method. I already add an Data Action icon
-
Unable to see Member disk in ASM through DBCA
Hi I am having standalone(NON-RAC) box with Linux AS3(Kernel Ver. 2.4.21.4) and oracle 10G installed on it. It is having one database as ORCL. Now i wants to configure ASM on it. For that I did the following activities. mkdir -p /u03 mkdir -p /u03/as