Storedge 3310 read error

I've just installed 5 new Sun 146GB 10K drives in my SE3310, attached to a Sun 280R. The install and LUN setup went fine, format went fine, but I'm getting this error on the console and in /var/adm with some frequency:
Sep 10 08:59:12 onestop scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@0,1 (sd74):
Sep 10 08:59:12 onestop incomplete read- retrying
Sep 10 09:11:28 onestop scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@0,0 (sd36):
Sep 10 09:11:28 onestop incomplete read- retrying
Firmware version is 3.250.
What's this telling me?
Thanks,
Harry

Look at patch 113722-16 README.
RAID firmware 325Q addresses the following issues:
4826944 Copy and Replace function during rebuild causes data corruption
*4809793 scsi incomplete retry errors when cache is optimized for Random I/O*
4809787 After "defaults restore" fw asks for a controller unique id
4802207 SCSI Bus Reset and daemon.error under heavy load test for 3310
*4792748 3310 incomplete read- retrying w VTS*
4764506 Enabling secondary RS-232 port causes serial communication failure
may it be your case?

Similar Messages

StorEdge 3310 RAID hung.

During the billing run on a Sun Fire V440, the attached 3310 hung. Reboots of the server did nothing to improve the situation, but once the RAID was powercycled everything was alright again.
sccli version 2.1.1
built 2005.09.16.23.10
build 1 for solaris-sparc
Vendor: SUN
Product: StorEdge 3310
Revision: 0325
Peripheral Device Type: 0x0
NVRAM Defaults: 325S 3310 v1.37
Bootrecord version: 1.31G
Serial Number: 07CB61
There are no "event" entries for this trouble listed in sscli, and everything comes up green. The only errors we received at the time were that of SCSI errors:
Aug 10 10:49:30 InfranetDB01 scsi: [ID 107833 kern.warning] WARNING: /pci@1f,700
000/scsi@2,1/sd@0,0 (sd16):
Aug 10 10:49:30 InfranetDB01 Error for Command: write(10) Error
Level: Retryable
Aug 10 10:49:30 InfranetDB01 scsi: [ID 107833 kern.notice] Requested Block:
289557696 Error Block: 289557696
Aug 10 10:49:30 InfranetDB01 scsi: [ID 107833 kern.notice] Vendor: SUN
Serial Number: 29C8306F-00
Aug 10 10:49:30 InfranetDB01 scsi: [ID 107833 kern.notice] Sense Key: Unit
Attention
Aug 10 10:49:30 InfranetDB01 scsi: [ID 107833 kern.notice] ASC: 0x29 (power
on, reset, or bus reset occurred), ASCQ: 0x0, FRU: 0x0
Aug 10 11:01:12 InfranetDB01 scsi: [ID 107833 kern.notice] /pci@1f,700000/scsi@2
,1 (mpt1):
Aug 10 11:01:12 InfranetDB01 got external SCSI bus reset.
Aug 10 11:01:12 InfranetDB01 scsi: [ID 365881 kern.info] /pci@1f,700000/scsi@2,1
(mpt1):
Aug 10 11:01:12 InfranetDB01 Log info 11030000 received for target 0.
Aug 10 11:01:12 InfranetDB01 scsi_status=0, ioc_status=804b, scsi_state=8
Aug 10 11:01:12 InfranetDB01 scsi: [ID 107833 kern.notice] /pci@1f,700000/scsi@2
,1 (mpt1):
Aug 10 11:01:12 InfranetDB01 got external SCSI bus reset.
[repeat]
The question is whether or not to upgrade the firmware. Since the current firmware is so old (version 3.x) there seems to be special instructions to bring it to 4.x, and eventually 4.15G. Which would include OS patches as well. (117171-12).
Or, just carry on, since this has only happened once (during the last billing run) in the last 9 runs/months.

What is the difference between the host/drive channel? Besides the fact that they are their for connecting to disk drive or to host. Because lets say I connect the first RAID controller to the second one, host-to-host configuration from one RAID to another, will the host see this transparently?
By the way, I tried the JBOD method you mention so basically just connect one of the RAID unit to the other one just as a JBOD and the RAID controller can see the disks on a difference channel but only half of the disk because the RAID I/O actually have internal conneciton to half of the disk, while the other half is jumper.

Multi-initated LUNS on Sun StorEdge 3310

I recently received two Sun V20Zs and a StorEdge 3310, and I am asked to cluster these two machines with the 3310 as shared storage. 3310 came with two raid controllers.
My question is, could I create multi-initiaged LUNs and have these LUNs mapped by the V20Z. Reason behind having the multi-imitated LUNs is it will facilitate fail-over in case a one of the V20Z are unavailable.
V20Zs are running Fedora Core 3.
Thanks for your help.

A good output that would give you a hint of a problem is iostat -En
This output reports anykind of errors to a particular disk since the last reboot. If you are seeing high error numbers, then you can move onto running a file system check - fsck - on the drive.
If you have anykind of RAID setup, check to see if any issues are being reported. Depending on what you are using to manage the RAID - Veritas Volume Manager or Solaris Disk Suite - they will most certainly tell you if there is an issue. A vxprint for Veritas and a metastat for DiskSuite will show you what you have setup and if there are any recognized disk issues.

Not all storedge 3310 disk showing up

I have a storedge 3310 hooked to my V440 running solaris 8 and not all the logical disks are showing up in the format command. I have a total of 4 logical disks configured on the array, two on the primary controller and 2 on the secondary controller. It appears that I only have one logical drive from each controller appearing. Any help would be appreciated.
Thanks

That worked however, now when I run format I get the following errors:
8. c4t1d1 <SUN-StorEdge3310-0325 cyl 34474 alt 2 hd 64 sec 32>
/pci@1d,700000/scsi@1/sd@1,1
9. c4t1d3 <SUN-StorEdge3310-0325 cyl 34474 alt 2 hd 64 sec 32>
/pci@1d,700000/scsi@1/sd@1,3
Specify disk (enter its number): Feb 21 18:10:44 socorro scsi: Vendor 'SUN', product 'StorEdge', 70606848 512 byte blocks
Feb 21 18:10:44 socorro scsi: WARNING: /pci@1c,600000/scsi@1/sd@0,2 (sd160):
Feb 21 18:10:44 socorro corrupt label - wrong magic number
Feb 21 18:10:44 socorro scsi: Vendor 'SUN', product 'StorEdge', 70606848 512 byte blocks
Feb 21 18:10:44 socorro scsi: WARNING: /pci@1d,700000/scsi@1/sd@1,1 (sd204):
Feb 21 18:10:44 socorro corrupt label - wrong magic number
Feb 21 18:10:44 socorro scsi: Vendor 'SUN', product 'StorEdge', 70606848 512 byte blocks
Will look into thme and see if I can get them resolved.
Thanks

Veritas Volume manager 4.0 with Sun StorEdge 3310 D

I am running into a problem. The vxconfigd deamon always dump core when rebooting.
Our environment is listed below.
OS environemt.
     SunOS server1 5.8 Generic_117350-43 sun4u sparc SUNW,Sun-Fire-V240
Software installed.
     Sun Cluster 3.0
     Veritas Volume Manager 4.0 MP2.
Disk Array associated.
     Sun StorEdge 3310 D.
I looked up veritas.com and find Array Support Library (ASL) for Sun StorEdge 3xxx Series is recommended. But I didn't find this library is running on this server.
Please refer to this following link
http://support.veritas.com/docs/277923
As our system is one of critical systems and I'd like to confirm that I can follow up this procedure without doing harm things to our system.
Jeff

No problem Jeff :)
I took a look at the Veritas doc and you're right it does seem to cover everthing.
Has the vxconfigd core dumped since the start? ie from the moment it was installed?
I have installed VXVM 4.0 with Solaris 8 but without the ASL and this worked ok, I know that's not much help to you but I am not sure the ASL will help. Mind you I have not installed it with Sun Cluster 3.0.

Partition Storedge 3310

Hello All,
My first connection on this forum & I would need your help.
I have to configure a Storedge 3310 (6 disks 72Gb).
Already created:
1 Logical Drive: 5 disks in Raid 5 + 1 Spare
Size of the drive: 279GB.
I need to create 11 partitions (10*12GB + 1*159GB), but apparently, I can create only 8 partitions (from 0 to 7).
Could you help me? I don't know how to do.
I already read this topic: http://forum.java.sun.com/thread.jspa?forumID=831&threadID=5098175
But the answer is not really clear (for me...)
Thx.
Eric
Message was edited by:
Eric_MdZ

I had to do something similar on site today, I believe (although have not tried it) that you alter the number of partitions to create on the 3320, however an alternative way of partitioning the Logical Drive is to let Solaris do it, by that I mean LVM ( formly known as disksuite). Bring the logical drive into solaris and create one large partition. Bring that single partition into LVM and then use "soft partitioning" to break it up. I have done this before and it works fine, its just another way of doing the same job albeit on the host and not on the Array.

Adding 146GB drives to StorEdge 3310

I have a StorEdge 3310 with 6 72GB drives in it (RAID 10). Customer wants to add a pair of 146GB drives to increase capacity. Is there any issue with having disparate sized drives in a 3310 RAID array?

I have a 3310 disk array with 12 72gb drives ,
configured raid 5 , 1 hot spare...The host side scsi
parms are max queded i/o 256, luns /host 32, max #
concurent host lun 128, cyl/head/sector
cyl-65536,head-64, sector-255...... NO problems.
I have added a 3310 expansion unit to the original
disk array. expansion unit also configured raid5 ,
one local spare. sd.conf also update. I am able to
newfs, mount and use the disk. however it odd
compared to othe disks when using the solaris format
command. questions are the OK for 146gb drives. I
noticed that one of the options for cyl/head/sector
was variable. does anyone have experience using the
option???

Converting Storedge 3310 RAID unit to act as JBOD?

Hello, I have been struggling with this configuration, any advice is appreciated.
I have 4 x Storedge 3310 RAID units each with it own controller. I have 1 x Linux host and 1 x HBA in the host, with ch0 and ch1. I want to be able access to all 4 Storedge 3310s. Normally if this were 2 x Storedge 3310 RAID + 2 x JBOD then I just connect each RAID unit to a JBOD then each RAID to ch0 and ch1 respectively to the host. Instead what I have is 4 x Storedge 3310 RAID units, is there a way to convert two of the Storedge 3310 unit to make it act exactly like a JBOD? So that I can daisy-chain them to make them all accessible to the host?
Or adding another HBA card to the host is the only option?
thank you.

What is the difference between the host/drive channel? Besides the fact that they are their for connecting to disk drive or to host. Because lets say I connect the first RAID controller to the second one, host-to-host configuration from one RAID to another, will the host see this transparently?
By the way, I tried the JBOD method you mention so basically just connect one of the RAID unit to the other one just as a JBOD and the RAID controller can see the disks on a difference channel but only half of the disk because the RAID I/O actually have internal conneciton to half of the disk, while the other half is jumper.

Sun Storedge 3310

I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2? If ther is could you tell me how. I know how to do it on server 2003 but 2012 r2 is much different.

Hi,
I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2?
Since we are not familiar with the product you have mentioned, I would suggest you contact corresponding vendor support to get more specific and accurate response.
Thank you for your understanding and support.
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Connecting to a Sun StorEdge 3310

Hello all,
in our warehouse I've found a Sun StorEdge 3310. I want to try to use it but I do not have any kind of usefull serial cable. Also StorEdge has a LAN port but I'm not able to find a mac address to force ARP table and telnet it.
Any hint to get my storage accessible?
Thanks
Stefano
http://www.stefanocislaghi.it

Please have a look at the installation document http://docs.sun.com/app/docs/doc/816-7290-19 and feel free to get back here if you still have questions.

Password on storedge 3310

I have a old storedge 3310. There is a password on there that I do not have. I'm running ubuntu 14.04 on the server. I do not have any software the came with storedge 3310. So how do go about change the password? I know that if I had all the sun software this would not be a problem but, I have not been able to find any. I'm using a serial cable to connect the 2 servers together.
Thanks

Do you know the current password on the 6120?
If not, then I'm afraid you'll need a service engineer and downtime on the array to change it.
If you do know it, then you just telnet to the 6120; log in with the username 'root' and the current password and then issue the 'passwd' command.
HTH,
--A.

Got reading error when deploying a web Dynpro project

Hi everyone,
I'm working on NWDS 7.1 CE. After I synchronized a project (using the "Create Project" option), then Build and Deploy it under the Development Infrastructure perspective, I can run it by choosing the "Run" option of the web Dynpro project's application. But once I chose "Deploy new arcihve and run", I got the following error message:
[ERROR CODE DPL.DC.3095] A reading error occurred while loading the SDU 'D:/usr/sap/DW1/J00/j2ee/cluster/server0/temp/tcbldeploy_controller/archives/3888/dow.comgcacmpprofitcenterui.ear'.; nested exception is:
     com.sap.engine.services.dc.util.readers.sdu_reader.SduReaderException: [ERROR CODE DPL.DC.3388]
The specified file D:/usr/sap/DW1/J00/j2ee/cluster/server0/temp/tc~bl~deploy_controller/archives/3888/dow.com~gca~cmp~profitcenter~ui.ear is not a valid SAP deployable unit. In case it is Java Enterprise application, please convert it to SAP compatible deloyable unit first.
Additional information: 'The information about the development component found in the manifest is either missing or incomplete!
Manifest attributes are missing or have badly formatted value:
attribute keylocation is missing
attribute keyname is missing
attribute keyvendor is missing
attribute keycounter is missing
Does anyone know what happens here? What's the difference of the Build/Deploy commands under Web Dynpro perspective and under Development Infrastructure perspective? After I made changes to the project, can I just deploy it under the Development Infrastructure perspective?
Thanks,
James

Hi Nilesh,
       Try opening Visual Admin if your not able to login with username(administrator) and password. Problem with NWD2004s do the following steps.
C:\usr\sap\J2E\JC01\j2ee\configtool->configtool.bat->open it
1. Click on Secure store
2. Right you will find :
admin/password/J2E->retype your admin passowrd which you gave during installation=>SAVE properly
Restart the server and try login visual admin
       Deploy now...Other wise see this thread same error solved:
Re: An Deploy Problem about Credentials.
Regards
Suresh

My Itunes wont open - reading error "cannot be read because it was created by a newer verdion of itunes"

My Itunes wont open - reading error "cannot be read because it was created by a newer verdion of itunes"
should i uninstall/ reinstal.
will i loose all my music nd playlists?

This technique should work...
Empty/corrupt library after upgrade/crash
Hopefully it's not been too long since you last upgraded iTunes, in fact if you get an empty/incomplete library immediately after upgrading then with the following steps you shouldn't lose a thing or need to do any further housekeeping. In the Previous iTunes Libraries folder should be a number of dated iTunes Library files. Take the most recent of these and copy it into the iTunes folder. Rename iTunes Library.itl as iTunes Library (Corrupt).itl and then rename the restored file as iTunes Library.itl. Start iTunes. Should all be good, bar any recent additions to or deletions from your library.
See iTunes Folder Watch for a tool to catch up with any changes since the backup file was created.
When you get it all working make a backup!
tt2

Socket read error: connection reset by peer

Hi.
Has anybody experienced the error message �Socket read error: connection reset by peer�
Please see below for detailed information.
Appreciate your help
Regards
RT
Enviroment specification
Server: HP/UX 11.00 64-bit, Oracle RDBMS 8.1.6.0.0 64-bit
2 firewalls between client and db.
Client:
Win 2000,
SP3,
Oracle Client 8.1.7.0.0 ,JDBC OCI (thin JDBC driver,class12.zip)
JDK 1.3
JRUN3.0
The TCP protocol is being used in the communication
Error messages
Web Users receive: Socket read error: connection reset by peer
Trace files on the sever: Read unexpected EOF ERROR on 18.
Explanation: The error in the server sqlnet trace file, suggests that a client connection has terminated abnormally, i.e. client machine powered off, a cable removed or a network connection aborted without warning. No user has complained of such a problem and there is no client trace with an error.
The problem
The users of the java web application, experiencing an exception almost once or twice a day.
The JRUN web-server reports broken connections to the db and client are receiving "connection reset by peer".
At the moment when the errors occurs the users just have to wait a while(2-10 min) and then they can use the web application again.(no action is taken)
This problem can not be reproduced. The problem happens only occasionally when the network is under heavy load and new DB connection is being created.
The application
The java web-application uses a customized connection pooling against the database. This pool is shared among all the users of the website. whenever a user process needs to fetch data from the database, a free connection from this pool is allocated. The application is testing if the connection is valid before making a transaction (select '1' from dual). When the error occurs a ORA-3113 end-of-file on communication channel is returned to the application.
The path between the client and db involves at least two firewalls. The firewalls are opened for sql*net traffic. The network group can tell that enquiries from the app.server is not getting feedback from the db. They have not however, identified if the enquiries are reaching the db-srever, or if they are stopped earlier in the network.
Around 1000 users, are using other applications which uses dedicated sqlnet connections against the db and they have not experienced any problems.
Issues considered
Connection pooling
It is a customized connection pooling, developed by Lindorff developers.
I have read through the source code for the connection pooling and it does the job as it should, and in case of bad connection, it tries to create a new connection.
The log file shows that the call to the method DriverManager.getConnection() hangs until the server goes down, which is probably because of the fact that the method DriverManager.setLoginTimeout(), does not take effect and timeout value is Zero. ( According to oracle , Oracle JDBC does not support login timeouts and calling the static DriverManager.setLoginTimeout() method will have no effect).
Firewall
One thing to consider is when the firewall may decide to shut down the socket due to long inactivity of a connection. This will cause problems to JDBC Connection Pool because the pool is not aware of this disconnection at the TCP/IP level; until someone checks out the connection from the pool and tries to use it. The user will get a Socket read error: connection reset by peer.
Jrun timeout paramter is less than the firewall�s timeout so the firewall will not close a connection before Jrun does.
Number of processes the DB can handle
Processes parameter is 1300, , they have not experienced the Oracle error msg �max # of processes reached�.
Port redirection through a firewall:
Since the firewall has a sql net proxy Port redirection through a firewall is not a problem. Problems with port redirection only appear at connect time, but in this situation the connections fail long after the connection is established.
The network group
The network people who investigaged the problem at Lindorff report that there are a significant amount of "dropped packages" between the database server and the jdbc client (web-application) 24 hrs. The reason for this is "unknown established TCP packet" which means that the firewall does not consider these packages to be part of an already established session. The network group believes this happen because one of the hosts send a RESET or FIN signal which the firewall have noticed but are not received by the other host.
It seems like the firewall are dropping packages bacause of "Unknown
established TCP packet" from both the JDBC client and the TNSLISTENER on the database server. The dropped packages are SQL*Net v2 traffic so clearly Oracle products are involved

Presumably something is working.
Thus the problem is not with your code. At least not the database part that you have control over.
That error occurs when the other side closes the socket. Presumably you are catching lost connection exceptions and trying to restore it.

"A Disk Read Error Has Occured" past 239 FSB?

The title says it all. I'm runnin an Neo Platinum 2 and when booting up overclocked past 239 FSB I get "A Disk Read Error Has Occured" and it asks me to reboot. Is this as simple as my SATA being overclocked too far? I was under the impression this board had an SATA lock, but I could be wrong. Any suggestions on getting past this? Or have I reached my peak?

Quote
Originally posted by sarlen
67 mghz? That doesn't make any sense - giving it a try right now though. The ram is tricky though, I hear Ballistix is unrealiable. I'm doing 2.5-2-2-5 at 243, but nothing will make it run 255 for me (next step up to keep my cpu at 2.55). I suppose 243 isn't bad, anyone have any ideas on getting more out of this ram though?
my 3200XL doesn't even reach 210 with ras cas at 2 :/

Storedge 3310 read error

Similar Messages

Maybe you are looking for