Suggestions for Backup ACS v.5

Hi,
I was wondering if anybody could share how they have setup the backup configuration.
When I compare the backup files from the ACS v.5 with those in v.4, the backup files are much larger. I had the backup files from the v. 4 server saved on a network share on a windows server. Each dmp file was just 600 KB, so we had the last 20 Backups saved on the drive.
When I make a backup of a ACS v.5 Configuation - which I use for Tacacs device authentication, so we have a pretty large configuration with about 15000 devices on it, the backup is 800MB! We would quickly reach the limit of the drive...
what is sensible to do here ?
Thankx!

Hi Ida,
The ACS 5.x and 4.x are totally different as you already probably know, you are right in 4.x the backup size are very small they will almost never reach the MB size, however 5.x is a totally different story.
5.x has different backup files, one for configuration, one for configuration + CLI, one for logging section. The most common backup and the most important as well is the configuration backup, this one can be collected from the CLI using:
ACS# acs backup backup-name repository repository-name
Or you can configure the ACS to collect configuration backup files by schedule from System Administration section, this option will collect the configuration settings only. However the backup size still will be MB size.
Rate if it helps!

Similar Messages

Suggestions for Backup Software

Hi, I am looking for backup software that is easy to use, with full backup each time and that is reasonably priced - your recommendations. Thanks - Bob61

Hi
I am looking for the same thing I think. I have a G4 Powerbook and I want a simple backup utility that will backup everything just in case my hard drive corrupts beyond repair. I had a Dantz on my old PowerMac and just hit backup and it would backup everything on the hard drive. I don't want to have to select files, drag them or at all be concerned that I am forgetting to back up some file. I was looking at the Dantz Retrospect V4.1 Express but I don't know if that is the latest, is it good or what. Is the SuperDuper a program that will just do a complete backup of the hard drive, looking for changes each subsequent time and backing all of them up?
Thanks for any help.
Hi Bob61
I've been using SuperDuper for a couple of months now
and really like it. It's priced at around $29 and as
shareware you can try it out first to see if it fits
your needs. It can be set up in a number of ways to
take care of your backup needs and will also do
bootable full backups which is, I guess, what you're
looking for. You can get it here:
http://www.macupdate.com/info.php/id/13803
Good luck and happy new year!
Rick

Suggestion for backup drive for Air

I've enjoyed getting to know my MacBook Pro this past year or so, but I'm still new to the Airbook and need some assistance. I'm going to help an elderly friend move data from her old iMac to her 1st Gen. Airbook. I'm insisting she get a backup drive, but the Seagate Free Agent I recently bought won't work for her, because it is either FireWire, which Airbooks don't have, or it requires two powered USB ports. Given that the Air has one USB, would we be able to get around it by using a powered USB hub? Is there a specific drive that anyone can suggest? I'd prefer Mac formatted/ready to go, but not absolutely necessary. An external drive with a built in power supply tends to be bigger than we'd prefer. What about a USB flash drive? I don't think she's filled the 80 GB solid state drive on the Air so she doesn't likely need a huge capacity drive. Any help you can give would be most welcome.

Hi SFMacNewbiew,
Happy to hear that you're enjoying your MacBook Pro.
I have the following drive currently:
http://store.apple.com/us/product/TR043ZM/A
What's nice about it, is that I have FW flexibility. The cable for the USB has the double USB cables and I've been backing up to it using the single USB (power & data) without problems for 4+ months now.
I've also used this one as well:
http://store.apple.com/us/product/TV523VC/A
When you think about it, the second one is a better bang for the buck. It is, however, USB only.
One thing you mentioned is that she has an older iMac, so getting a drive with a FW interface wouldn't be all that bad and with enough storage she could theoretically use the HD with both machines. I've yet to come across a reasonable priced portable HD that I've had to use with a powered USB-hub.
Regarding the thumb drives, I'd recommend against them. Even a "base install" with some data is 12-19 GB on most MacBook Airs unless she did a custom installation.

Ever since upgrading to Yosemite on my Mac, I can only configure my time capsule via iPhone. My Mac cannot locate for backup, but CAN find as my internet router. I have followed all suggestions I can locate and have upgraded to newest version.

Time Capsule in Yosemite can be used for router/internet but Mac cannot locate for backups.

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

Drive setup suggestion for multiple users editing simultaneously?

At work here, a city college, not a professional company or broadcast studio, so resources are limited, we often have three people editing HDV content simultaneously in Final Cut Pro.
Keeping the content on our multiple backup servers, there's simply too much network traffic to do this smoothly.
Instead of keeping projects locally spread across multiple machines, I would like one centralized place for everything, for the Macs to access directly over gigabit or something else.
So, what kind of setup do you guys suggest for this?
The machines here are two quad-core G5s (no RAID or fiber-channel right now), and a Core2Duo iMac, F400 only.
Again, it'd need to be able to handle three HDV projects going on simultaneously without skipping due to having to seek back and forth all over the drive.
Thanks.

Yes, an XSan system would perfectly fit the bill for what you want to do, but an XSAN is not a cheap solution. When it is all said and done, it will cost you tens of thousands of dollars.
The best, cheap solution would be to use Firewire drives. I would not duplicate a project onto three drives, because you will then always be trying to figure out which version is the most current. Instead, keep all of your project, capture scratch and render files on the firewire drives. Then move the drive to whichever computer you want to do the editing on.
Properly log & capture all your footage, then archive all your project files, because Firewire hard drives will fail over time, loosing all the info on the discs. I did say this was the cheap solution. "Cheap" does have its costs…

Suggestions for setting up external storage for video editing please?

I am just starting up as a one-man video-editing business, using a 24 inch iMac running Snow Leopard, with Final Cut Studio. I have realised I'll need an external hard drive for HD footage, and I also need to get some back-up solution in place. Looking for speedy i/o, I would like to connect via the ethernet port (if only eSata was included in the iMac, eh!)
I've been planning to get a Drobo, but looking around the forums I see that people say it's too slow for using as a working drive to keep all my source footage, so I've been looking at the G-tech 4 Tb, as it says it is designed for media-content production. Does anyone know if I could use two of the drives for working from and two as back up? Or would it be better to keep back-up entirely seperate, and get a Drobo for that for the G-tech to back up to?
But I am also wondering whether a Mac Mini could be a worthwhile addition to this set up? I find myself sitting around waiting for rendering to complete on clips in my timeline (not to mention exporting to Quicktime conversion!), and I wondered if I put a Mac mini with Xserve installed (Apple store offers this with two 500gb hard drives inside), maybe I could farm the rendering out to the mini while I get on with editing on my iMac? That would require two installations of FCP, which I thought was allowed, but just today in a forum I saw that one would have to be a laptop... anyone have any suggestions for getting rendering done without stopping FCP from doing other things simultaneously?
Also I don't know if that arrangement is even feasible... I see all these things like Xsan and Artbox... as a one workstation editing suite, does FCP handle all the dataflows for external working drive and external back ups okay without having to introduce more controllers?
And can anyone explain to me how I could set up an ethernet connection to an external hard drive, or does that require the extra controllers mentioned above? I've seen it said that you can do it via ethernet, but haven't seen how you can actually go about doing it.
Thanks for overlooking my newbie quality, any answers received with humble gratitude!
Cheers, Syd

Hi there,
as NLEdit said, there will be loads of answers to this.
IMO i'd avoid drobo like the plague. G tech drives have served me incredibly well working on a huge variety of broadcast projects (just over the water from you in Bristol), I've had no probs with FW800 when using DVCproHD, pro res is ok, sometimes a little slow with multiple layers and of course it eats up storage space. so I'd go for 2 4tb drives, keep the backup one in a different location.
one tip that has saved me countless times is to format them as follows:-
mac os extended (not journalled)
create 2 partitions
partition 1 - make this small (1gig) and call it "drive a - do not use"
partition 2 - the rest of available storage and call "drive a"
this is because the boot sector of the drive is within the first partition and with this method if it goes down it can be re erased without losing all your footage.
If you call your backup drive the exact same name and have the exact same folder structure, you will not have to relink if you get a problem.
Ignore getting a mac mini for rendering, won't help at all in FCP. instead I would make every attempt you can at buying a mac pro rather than an imac. much more expansion/speed possibilities and a more robust solution.
best of luck
Andy

Time Capsule just for backups, not for wifi.

I used to use my Time Capsule for both backups and wifi but constantly had issues, so I just disconnected it in favor of a simple Airport Express. No issues since switching, but now I have this Time Capsule just sitting here and don't do automatic backups any longer...I would like to use solely for back ups, I don't need these backups to be wireless, just for use with Time Machine. I can't find the answer by google, any suggestions?

I am trying to do the same thing but I am having an issue.
I, too, was having issues with using the Time Capsule (new one-2T) as a router and for backup (the Internet was dropping all the time). So I bought a separate router (ASUS RT-N56U) and have that plugged into my Motorola modem. The Time Capsule I have plugged into the router.
Airport Utility and I have become best friends as of late with all the problems I am having and my TC keeps getting lost-AU says that it was part of my network and now can't be found. Strangely, if I go to Open Network Settings from the menu bar and select Assist Me--->Diagnostics--->Select my network--->Continue and when the window pops up about Always Allow Keychain, I click on Always Allow. And that seems to correct the problem with my TC not being found/part of the network. This happens all the time lately.... Ever since I got the new router.
So if you or anyone have any insight into what is going on.... I will try it! Thanks for the help, Judy

Using Time Capsule for backup only (no Wifi)

I posted a problem in another thread ( https://discussions.apple.com/message/22500623#22500623 ) about conflicts with my Time Capsule and Comcast modem. Apple concluded that there was a hardware problem with the Time Capsule. I got a new Time Capsule yesterday since I couldn't get a refund on the old one. Because configuring the Time Capsule to work as a Wifi station requires such a hassle and I don't get any extra benefits in terms of speed compared to my Comcast modem, I now have a very expensive hard drive for backup. I have some questions about using the TC for backup only since I am running into some problems with the backup.
1. Does the TC have to be connected to my modem? It seems that when I do not connect the TC to the modem then I end up with the backup stalling after a few GB. Additionally, I end up with the flashing amber light.
2. If I do connect the TC to the modem it backs up but my WIFI grinds to a halt (likely a product of all the data pushing from the computer through the modem and to the TC). I should add that in Airport Utility I have turned off WIFI on the TC so it should not be interfering with the WIFI. If I do need to connect to the modem are there any tips for not messing up WIFI speeds beyond just backing up when everyone is asleep? I assume not, but it can't hurt to ask.
Thanks.

2. My initial setup showe various errors so I hooked the TC into the modem via the WAN port and then I was able to set up (WIFI off, Bridge Mode OFF) and those errors went away.
If I understand your last post correctly, you say that I should do a reset on the TC. Re-configure but leave the errors because backups will still work. Then I can leave the TC unplugged until I need to use it (which has the added bonus of limited flashing amber light). Is this correct?
You are setting up the TC in the wrong mode.. it has to be in Router mode.. Not Bridge..
You are worrying too much about the flashing amber.. it is irrelevant. You can select ignore and it will go green.
This setup is actually simple.
So here is what I suggest.
1. Factory reset the TC.
Just to get started from a clean setup. And that will put the TC in the correct mode.. ie dhcp and nat.
2. Plug it by ethernet LAN TC to computer. On the computer no other connection.. turn off wireless.
3. Just change the name of the TC to something short as it helps.. eg TCGen5
And turn the wireless off.
And ignore all the other problems.
4. Now setup TM.. I would also start clean.. do a fresh TM setup .. see A4 here.
http://pondini.org/TM/Troubleshooting.html
5. Run the backup. Maybe even erase the TC before you start so you are really doing a fresh clean backup.
The very first backup will start quickly and drop to very slow speed as there are heaps of very small files in the system.. these take a long time to process.. but as it proceeds it will speed up. Overall you should still average 50GB/hr.
6. Once you complete the first backup, later ones should be fine.. but do not expect them to work as well as when you do it hourly.. it does need to do a lot more work to figure out where the TM backup is up to.
I would like to get you to have another crack at using the TC properly in the network. When you are over the pain of all this.. and perhaps when apple releases a decent firmware update you can go back to it.. but I have another suggestion for setup. Get the above working first so you have a good first backup of all your computers.

Multiple Hard Drives: one for system & applications, one for backup

I am planning the upgrade of my hard drive setup. Presently, I have only the original 74.53 GB internal drive that came with my June 2004 G5 1.8 dual CPU. I have two goals for the upgrade. First, more hard drive space. Second, a drive for automatic backup. Since I am running OS 10.4.11 and not intending to upgrade to 10.5 at this time for application reasons, I will be using something like Carbon Copy Clone for the backup software (not Time Machine, which requires OS 10.5). My thinking, so far, is to install a 1 TB internal drive for system and another internal or external 1 TB drive for the backup. In perusing the discussions here, it looks like an external drive is always used for the backup. Is this true or would an internal drive work just as well for backup? I want the backup to be as free as possible from any corruption or problems that might arise on the system drive or other computer parts. Does the Firewire or USB connection of an external drive offer a greater amount of freedom from potential corruption as opposed to the direct SATA connection of an internal drive?
I realize that burnt DVD’s offer the greatest amount of freedom from corruption but one doesn’t burn a DVD hourly, daily, weekly or so on. Hopefully, if a problem arises my work underway is residing on the backup drive unaffected. I’m not sure how close in time this can be. I imagine this probably depends on the backup software used and how often the backup is run. I’m not yet fully aware of the options.
For the internal system drive is there any good reason to partition it? I f so, why, and in what way? Do the OS and applications need to reside on the same partition? If not (or better that they don’t), how should a 1 TB drive be partitioned?
Thanks in advance for any suggestions on the best configuration of my hard drive upgrade.

1) The backup drive is best to be external (security from computer failure).
Yes. I am not sure about the "in some ways" my esteemed colleague qualifies.
2) The external backup drive should be connected by Firewire (ability to be bootable & greater speed).
Yes. Just beware that some of the Western Digital models have presented problems. Not the drives themselves but the enclosures. [List of Western Digital bootable and non bootable models|http://discussions.apple.com/message.jspa?messageID=9022456#9022456]
Is a Firewire connected drive any less vulnerable to damage by computer hardware failure than an internal drive?
Yes & no. The yes: I don't know about G5s (they use a different connector from the G4s and earlier with which I am familiar) but in some computers the drives will share the same controller. If the controller goes then all connected drives can be corrupted. The no: Then too, I have had two Firewire drives be corrupted. One was by trying it with a PCI card (not what you're using) that was incompatible with my model computer. The other was when the power source in the enclosure went bad.
This is almost leading me to think that 3 drives would be the best! One internal for OS system & applications (1 TB), one continually connected for auto backup (my original 74 GB), and one (a bootable clone) attached only during occasional backups (2 TB).
The more the better. I usually buy drives in size increments that make sense for my configuration. I have two 120GB internal drives so I bought a 250GB external drive for backup and partitioned it into two so I could just back up one internal to one partition and the second to the other.
I'm perplexed with both your feelings about burnt media. I was not aware of this and fortunately have not experienced problems. However, it is only recently that I gravitated from 700MB CD's to 4.7 GB DVD-RW's for backups. I've been using Maxell
There's backup and there's archiving. Backup is for having a copy of what you're actively using. Archiving is storing stuff that is unlikely to change. Optical media is lousy for backup because files are constantly changing. Backing up a 120 GB onto 4GB media either requires a super organized person or you're spending a day sticking DVDs into your computer.
Optical media is less lousy for archiving, but still not great. Where's the floppy drive on your computer? Where will the DVD drive be in 15 years? It's also a lot faster archiving onto hard drives, and the cost of drives has come down to where the per GB cost is about equivalent of less than high-quality, archival-grade DVDs. Yes, drives change too, but it is also easy to copy from drive to drive. I have items archived on drives that are over 10 years old and as long as I make sure I keep on top of being able to connect those drives to a computer they are usable.
BTW: I tried to quote your messages for this reply, went to "Help" to learn how that is done and found this: "If you want to quote specific text from the original message, click Quote Original to add all the text from the original message to the Message box." I could see no such button "Quote Original". Can anyone please tell me where it is?
There's a '"' icon in the compose window when you type a reply. If I'm doing a lot of quotes (as I did here) I use that, then edit out the bits I don't want. Otherwise I copy and paste the text and add a > before the line to get it to appear in the special format.

HT3275 I am using an external drive for backup. I am now getting a message that the drive needs a disk repair, but when I run disk repair it just seems to freeze.

I am using an external drive for back up. Yesterday the backup failed and I received a message that the external drive( a passport drive) needed a 'disk repair", when I ran disk repair nothing happened it seemed to freeze. Suggestions? should i simply erase the external drive and start over-my computer is fine.

Get a different drive for backup.
In the meantime, once you are backed up some drive safe, then you can attempt to repair the backup drive using the repair the directory link.

What kind of external drive should I get for my macbook pro for backups etc

what kind of external drive should I get for my macbook pro for backups and storage

Hi, i have a Mercury Elite-AL Pro from OWC, www.otherworldcomputung.com
this is the one;
http://eshop.macsales.com/item/Other%20World%20Computing/MEAQ7S1TB32M/
have had this for over two years, moved around a lot with the drive, ( to date ) no problems, they have good after sales support; give them a call if you need info.
There are a lot of drives out there as others here will let you know, there are good NAME drives but they also fail, POPULAR drives also fail, select the one you are happy with for your system and how you plan to use.
i suggest if $ is not a problem get a big drive you will find someting to put on it and is better.
hope this helps.

When ever the power goes out or I restart my iMac the external hard drive that is used by Time Machine for backups is dismounted ?

When ever the power goes out or I restart my iMac the external hard drive that is used for backups by Time Machine is dismounted and all backups are gone. I can reselect it and it will start working again, but I am worried if the iMac hard drive should fail will I be left without a backup ?

fzgy wrote:
"Mac OS X can't repair the disk. You can still open or copy files on the disk, but you can't save changes to files on the disk. Back up the disk and reformat it as soon as you can."
It's possible a heavy-duty 3rd-party disk repair app can fix it, but they're expensive (DiskWarrior is about $100), and there's no guarantee it can do it.
Am prompted to reformat but I don't have a good understanding of what this means and how to do it.
That will erase it. See Time Machine - Frequently Asked Question #5.
It sounds very much like the disk is beginning to fail, although it's possible there's a bad port, cable, connection or power supply (if it has its own).
I'd suggest getting a new one, and using it for your Time Machine backups; once you have a good backup there, reformat the old one (and select Security Options to write zeros to the whole drive -- if that fails, you know the drive is toast). Use it for secondary backups, per FAQ #27. If it has failed, get a second new one for secondary backups.

Suggestion for Apple or Third-party software company?

My first question is, where should I post the following suggestion for an improvement in FCP or for the creation of a third party software – suggested sites, blogs, etc.?
Next, my recommendation, and then my explanation of the reason why (including my personal semi-disaster):
Recommendation: That someone create a “Project Management” software for FCP (essentially a file management program that runs in the background) that organizes and tracks all of the files created during editing/post production – including the log/capture or log/transfer of the original footage, the audio files, stills, effects, etc, AND all of the files created by the program -- Live Type, Motion, Soundtrack Pro, and Color (especially color). The reason for this is that FCP has an incredibly complicated filing system that results in shots, files, documents, etc., being distributed all over the place – and not all known to the filmmaker or identified in the documentation. And, that condition can lead to disaster – see below.
Explanation: I just finished my first HD project using Studio 2, including sound track pro and color. After completing what I though was the absolute final version, I burned a one-off DVD and ran it by several filmmaker and non-film maker friends. They all spotted a small sound problem with one cut, so I went back to tweak it – and discovered that ALL of the footage had gone offline. I had nothing, nada, zilch. I had saved earlier sequences (rough cut, polished cut, etc.) and all the original footage appeared, but I had taken the final version into color for some corrections and adjustments, and ALL of those shots/files were missing.
After burning what I believed to be the final cut, I had cleaned up my hard disk, moving stuff to my backup hard disk, to my RAID array, and to the trash. So, after the initial shock and complete panic, several hours of searching all of these drives, led me to the file that contained the files that contained the color corrections – in my trash, which fortunately had not been emptied. I have no idea where the files were before or how they got into the trash – obviously they were not added to the scratch disk with all of the original footage.
Part of the difficulty of finding the shots was the discovery that color creates a file folder, that holds a set of file folders, each of which holds only one shot. In order to reconnect, I had to move the parent folder to the desktop, and then move all of the shots, one at a time. into a single folder, and then point reconnect to that folder. Problem solved.
However, now I face that question of archiving the project, moving all of the files off my hard drive so I can use the space for my next film, and I am terrified that I will leave something out, and not be able to recover the project in the future. Having a project management software that organizes and coordinates all of that would be a lifesaver – and well worth the purchase price.
Anyone who would like to explore this idea, please feel free to contact me – [email protected].

You've just learned a hard lesson. Put your current energy into your education, not finding a way to wallow in ignorance.
There already is a hardware device that will do what you want. It's called a "manual". In particular, the sections that relate to "where the program stores media". Pay very close attention to those sections and set up your computer so that all the scratch and storage pointers are aimed where you want. It's very simple to have them all go to one drive.
Then, when it's time to archive the project because you are starting a new project, just purchase another hard drive for the new project. They are absurdly inexpensive these days.
Remove the drive with your project to be archived from your computer (since you now know how to keep all the files organized, they will be all together) - and plug in a new disk for the next project.
If you want a backup, use carbon copy cloner to simply duplicate the drive (or simply just copy the relevant folders- you'll know which ones) to another drive (or get a RAID 1 device)
good luck,
x

I am unable to turn my ipod on. Suggestions for what might be wrong?

I have my iPod plugged in to charge. But it won't power on. Suggestions for what might be wrong?

If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this.

Suggestions for new external HD

I have a G4 powerbook with 80 GB of HD which is pretty much maxed out. Looking for an external HD to transfer pics on to, and to do some backup with. (Currently i use my iDisk for backup of my Documents folder, so haven't really needed Backup). Any suggestions for a good ext HD though? LaCie? Toshiba?
Also, I'm thinking I should upgrade my 512 of memory to full gig of memory. All this doesn't need me to lead me down the path of a new MacBook instead, does it?!

GoBraves:
Since you have a PowerPC Mac you should be sure to get a Firewire external HDD. This will enable you to make a bootable clone which will do double duty as a full backup and as an emergency boot drive.
Be sure that the HDD that you get is larger enough. Since they drives are now quite affordable I would not suggest anything less than 250 GB. You can partition this clone your HDD to a partition approximately the size of your internal HDD.
The element in a Firewire Drive that fails most often is the firewire bridge. You need to get a drive with the more reliable Oxford 911+ chipset like one of these external firewire HDDs at OWC.
Good luck.
cornelius

Suggestions for Backup ACS v.5

Similar Messages

Maybe you are looking for