Sync two cDaq 9178 chasis using NI9469 modules

I have found topics using the NI9469 modules to syncing cards, but I have not found topics regarding sycing mutiple chasis using the NI9469 modules.
Setup: two cdaq 9178 chasis, one chasis is all 9227 modules, and the other has 9229 modules. We will be putting in a 9205 and a 9213 as well.
I attempted to use an example VI from NI attached, but it just seems like something is missing. Up to this point I have largely used DAQ assistant so this is definitely a learning experience for me. NIMax recognizes the 9469 cards, and I have them connected correctly. I do not see any lights illuminated though. I assign the hardware I want to use in the physical channels portion of the VI, but I do not see anything populate in the data field when running.
Can anyone offer any advice?
Attachments:
Multichassis Synchronization Code with NI 9469 .vi ‏25 KB

I have since found two more examples of vis that might work for this. At first I'll be using only 9227 and 9229 cards, which I believe are Delta Sigma cards. So I'll focus on that vi. Can anyone tell me what the Oversample Timebase Source and Oversample Timebase? I don't understand it. The 9469 can sample at two speeds, but the oversample timebase on the main screen just increments by ones. What is its purpose?
I would like to add a write to measurement file vi. I would add this after the loop correct?
Attachments:
NI 9469 Delta Sigma Modules.vi ‏36 KB
NI 9469 SAR ADC - Slow Sampled Modules.vi ‏33 KB

Similar Messages

Unable to read 5th channel using cDAQ 9178 with NI 9219 modules

Dear LabView user,
I've made a VI for reading the measurements of a couple of LVDT sensors, a load cell and a couple of strain gauges. When I connect 4 of these sensors to my cDAQ 9178 with using 1 slot of NI 9219, then there is no problem for my VI. But if I use 2 modules, and connect the 2 LVDT sensors and the load cell to the first module, and the 2 strain gauges to the 2nd module, then my program only will show the readings of the first module and the readings of only 1 strain gauge on the 2nd module. I've found that there occurs an error for the 5th channel in the 'zero' state. It says my buffer size is too small... How can I solve this problem? I can't work with finite samples because it is a continious measurement.
I also have the cDAQ 9171 USB module, if I only connect 4 sensors to this module, the sample rate is high (100 Samples/sec), when I use the same configuration, but connect this with the cDAQ 9178, the sample rate is much lower however I use the same NI 9219 module to fill the slots. Is there some kind of setting I need to make when switching over to the cDAQ 9178?
I've attached my VI.
With kind regards,
Pete

Dear RavensFan,
Thank you for your answer.
"Have you tried swapping the modules between the slots and see if you still have the same problem or if it moves?" When I use the cDAQ 9178, I always use the first 2 slots next to the power suply and the usb connection, you mean that I should try for example the 4th and the 5th slot or other slots? I will try this on Monday, and I will let you know.
About the states machines inside a state: How is it possible then to use several buttons, like start and stop measurement and the 'home' button inside the state "measurement"? Should I make another simple state machine inside this state?
What about that 5th channel that I'm unable to read? The problem happens in my "zero" state: to acquire my "zero elements", the loop does the job for the 5 channels for the first 8 samples, after that, it doesn't want to sample the 5 channels anymore, it only does for 4 channels... It's something about the buffer size, but I don't know how to fix that.
With kind regards,
Peter

Compare and Sync two Sql server Databases using msDeploy

Hi,
I have two servers on each server I have sql server 2005 with the same database instance, So I want to use msdeploy to compare between two databases and then sync new rows,tables and any database object from first server to second one.
I used dbFullSql provider but dbFullSql provider used to sync for first Time.
Please if there any idea.
Thanks and Regards.
mhd

Hi Mohammed Oda,
Could you explain what your demand, i am not quite understand your description, if you are asking the SQL question please post in SQL forum.
SQL Server question please post to theSQL Server forum.
SQL Server forum:
http://social.technet.microsoft.com/Forums/sqlserver/en-us/home?category=sqlserver
Thanks for your understanding and support.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Using iSync to sync two macs

Is it possible to use iSync to sync two macs?
I use a PowerBook and a Mac Mini and it would be handy if address contacts and calendars could by synced easily.
I would rather not get a .mac account.
Surely another mac should show up when you click 'add device' in iSync?

In addition to the information Julian provided, you can use commercial software as an alternative to .Mac for some synchronization purposes.
SyncTogether from Mark/Space will synchronize five of the six .Mac data categories across user accounts on a single machine, across users on a local area network, and across the internet. Keychain synchronization is not supported.
BusySync from BusyMac provides local area network only synchronization and sharing of otherwise read-only iCal calendars.
You can also investigate such products as SpanningSync for synchronization of iCal calendars using Google, and Plaxo, which offers contact, event and tasks synchronization—in a not quite ready for prime time beta release—for the Address Book and iCal.

HT1495 how to sync two iphones togheter

How to sync two iphones togheter

If you use separate accounts you'll need to use two user accounts on the computer.

Physical Connections to use 4 counters with NI 9411 in cDAQ 9178 chassis

Hello,
Currently I have a NI 9411 module in a cDAQ 9178 chassis. I am using 2 of the counters to read frequency measurements.
From the NI 9411 pinout diagram (see pdf file attached to this post), these are the connections I made:
CTR 0 SRC, pin 1 to COM/ground
CTR 0 GATE, pin 2 to first frequency signal
CTR 1 SRC, pin 6 to COM/ground
CTR 1 GATE, pin 7 to second frequency signal
The problem is now I'd like to use the 3rd and 4th counters in my cDAQ 9178 chassis, but I am confused how to wire
in the 3rd and 4th frequency signals, because CTR2 GATE is pin 1 and CTR3 GATE is pin 6. Can I change the pin assignments
to use the other pins in the NI 9411 module for counter frequency measurements? I haven't figured out how to do that in MAX
configuration.
Thanks,
Anna
Solved!
Go to Solution.
Attachments:
NI 9411 pinout.pdf ‏72 KB

Hi EETDer,
The "C Series Signal Connections for Counters" help that you found is a good resource. One thing I want to point out is that for a frequency measurement on a single counter, you only need to wire the signal source to the CTR Gate. Internally, the module will route an appropriate internal timebase to the counters source, therefore you DO NOT want to connect the CTR Source to ground. On your device, you will just wire each signal into the counter source, thereby only utilizting pins 1,6,3,8 for your 4 frequency measurements.
Chris
National Instruments
Applications Engineer

I synced two of my email accounts via gmail's POP3 thing. But now my iphone's gmail inbox shows a random selection of emails (not most recent ones that are in my inbox). How can I make my iphone inbox match what I see when I log on using a PC?

I synced two of my email accounts via gmail's POP3 capabilities. But now my iphone's gmail inbox only shows a random selection of emails (i.e. right now it is May 31, 2013 but the emails in my inbox are a couple from Nov 12, a few from Oct 12, and then some way older than that and so on.When I log into my gmail from a computer, I see all my emails in the logical, standard order. How can I make my iphone inbox match what I see when I log on using a PC?

If you're trying to decide between using POP and IMAP, we encourage you to use IMAP.
Unlike POP, IMAP offers two-way communication between your web Gmail and your email client. This means when you log in to Gmail using a web browser, actions you perform on email clients and mobile devices (ex: putting mail in a 'work' folder) will instantly and automatically appear in Gmail (ex: it will already have a 'work' label on that email the next time you sign in).
IMAP also provides a better method to access your mail from multiple devices. If you check your email at work, on your mobile phone, and again at home, IMAP ensures that new mail is accessible from any device at any given time.
Finally, IMAP offers a more stable experience overall. Whereas POP is prone to losing messages or downloading the same messages multiple times, IMAP avoids this through two-way syncing capabilities between your mail clients and your web Gmail.
That is from the page that you linked- does highlighted part of message ring a bell?

Can I use iCloud to sync two devices with different apples Ids?

Can I use iCloud to sync two devices with different apple ID's

What do you mean by "apple ID"? There's an ID you can use at the iTunes store to buy songs, apps, etc. there's an ID you can use for your iCloud account - the two can be different or the same. So which service are you referring to when you talk about an apple ID?

Can I sync two computers when one is using lion and the other snow leopard

can I sync two computers when one is using lion and the other snow leopard

will my data be shared well using Mobile Me?

I have an old iphone 3 32gb and don't use it to make calls as I have a 4s but would like to use the 3 for music any suggestions as to how I can sync two phones with I tunes

I have an old iphone 3 32gb and don't use it to make calls as I have a 4s but would like to use the 3 for music any suggestions as to how I can sync two phones with I tunes

Plug the device into the computer.
Select the content desired to sync.
Sync.

Generic delta   using function module with two fields AEDAT AND ERDAT

Hi,
    i have scenario that i have to create a generic data source having delta using funcation module and the delta speci fields are AEDAT AND ERDAT . Is there possibility with out using these two fields ( i mean AEDAT AND ERDAT) in the extract structure can i create the data source . and provide sample code for me . it is very urgent.
waiting for the reply,
sri.c

Hi Sri,
here some coding, I hope this helps!
first, get the delta-field
      LOOP AT s_s_if-t_select INTO l_s_select.
        CASE l_s_select-fieldnm.
          WHEN 'ZDATE'.
            MOVE-CORRESPONDING l_s_select TO r_date.
            IF r_date-high IS INITIAL OR r_date-high = space.
              r_date-high = '9991231'.
            ENDIF.
            APPEND r_date.
        ENDCASE.
      ENDLOOP.
Cursor öffnen
      OPEN CURSOR WITH HOLD s_cursor FOR
      SELECT * FROM
      WHERE ....
      AND    erdat in r_date
      AND    aedat IN r_date.
      FETCH NEXT CURSOR s_cursor INTO CORRESPONDING FIELDS OF table e_t_data package size s_s_if-maxsize.
regards
Siggi
PS: Note that this coding only works for a very straight forward extraction.
Message was edited by: Siegfried Szameitat

I have synced two devices in FF. Is it possible to know which computers are synced using? I am worried about someone figuring out my email address and password.

I have synced two devices in FF. Is it possible to know which computers are synced using? I am worried about someone figuring out my email address and password.

HI nilhanw,
No currently there is not manage devices, only manage device. However changing the password will change the certificates on all the devices within less of an hour.
I hope this helps.

Sync two outlook profiles on E71 using MfE?

So, I have two Outlook profiles running on two separate servers; I want to be able to sync both with my E71 using MfE but so far no joy. I've managed to set one up but, unless I'm missing something, it looks the E71 can't deal with two different Outlook profiles (trying to set up the second overwrites the first)? Can anyone help me?

You are correct. One will overwrite the other. Why use two in the first place?
Show the KUDOS button some love.... Hit that bad boy.... It don't hurt....
Apple iPhone 5,
Retina MacBook Pro, iPad Mini, Nikon D4

I have two iPads. With two functioning iPads. Is it possible (on the same ID) to sync two of them differently with the same account. So I want to use the new iPad for all my current functions. The old iPad for just my music collection?

I have two iPads. With two functioning iPads. Is it possible (on the same ID) to sync two of them differently with the same account. So I want to use the new iPad for all my current functions. The old iPad for just my music collection and remove all the other stuff?

Very easily. I have an iPod touch and iPad on the same account with totally different content.
If you use iTunes, connect each iPad to your computer and open iTunes and deselect any automatic updating/syncing. If you don't sync with iTunes but have them set up independently, under the settings, App Store, turn off automatic downloads for apps, etc.
I'm old fashioned, I set up and sync my iPad and iPod to my computer and iTunes. Each device has a different name and I manage content manually and only allow sharing on what I want shared.

How to create a trigger using 9211 modules with cDAQ-9174?

I am trying to create posttriggered acquisition with an analog trigger using 9211 modules that are reading 4 thermocouples. I would like the data aquisition to start once a temperature of 90 degrees C is reached. I am not sure what I should put for the source of my trigger in my VI. Are these modules capable of using triggers, and if so, how do I go about creating one? Attached is the VI, thanks.
Attachments:
Thermocouple.vi ‏151 KB

The 9211 doesn't have any analog triggering capabilities. You'll have to implement the trigger in SW (like this example).
Best Regards,
John Passiak

Sync two cDaq 9178 chasis using NI9469 modules

Similar Messages

Maybe you are looking for