System errors and replys not posting

Over the last couple of days I've had several intermittent problems trying to view threads in this forum, mainly shown as System connection errors. Today I've also tried to post a reply in a thread, the submit appears to work (no error message) but my reply has not been added.
Anyone else seen this and know what's going on?
Cheers
Ian

Similar Messages

System error and restart not possible

Hi
I have developed the Proxy to SOAP scenario and it used to work normally as designed, But suddenly it started giving the System error and restart not possible,
I see the following error in the Runtime work bench on the Receiver CC
SOAP: response message contains an error XIAdapter/HTTP/ADAPTER.HTTP_EXCEPTION - HTTP 500 Internal Server Error
Can anyone let me know what the error is
Thanks
PR

Hii
If this channel was in working state earlier, then this error would mean that the receiver webserver hosting the webservice has some problem. You may contact the receiver system for checking out if they have problem at their end and if they agree resend the messages and it should pass through.
It may be problem with certificates even.
Best Regards

OIM after BP12 patch system error and logging not working

Hi,
I am using Weblogic 10.3.2 and need to install OIM. I have installed the 9.1.0.1 and then the patchset to 9.1.0.2. Then I have installed the bundle patch BP07 and everything was ok.
Finally I have installed the BP12: now i am unable to log in the OIM admin panel ( system error ) and i cannot connect with the design console (NullPointerException). The worst part is that OIM does not write a log file anymore, so i can't determine what's wrong. What should i do?
thx in advance

no errors, everything fine. The webapps (xellerate and nexaweb) are started normally.
As an additional information, i just tried to revert to BP07, it still doesn't work.

NOKIA N97 SYSTEM ERROR AND MENU NOT OPENING

I have a N97 which is a far cry from the N900. Anyhow, of recent when I try to access the menu a message pops up saying "System error" - so, I cannot access any of the other functions through Menu and, quite honestly, I don't know how else to access the menu. Any ideas or suggestions to resolve this would be appreciated!

Apart from loss of data I would probably suggest carrying out a "hard reset" upon this device, which is chronically short of phone memory:http://mynokiablog.com/2009/07/18/how-to-hard-reset-your-nokia-n97/
Happy to have helped forum in a small way with a Support Ratio = 37.0

ALE : Error msg 'Application not posted'

Hello all,
when i send master data from sender to receiver then at recaiver side it shows the error like 'Application not posted'.
what it means ?
I have checked all the connection for both system.Remote connection is also working.IDOC generated at sender side is showing status 3. i.e. data is successfully transfered
whats the problem?
regards
Nilima

Hi Nilima,
Application not posted. error is for data integrity as already said.
Means that document can not be posted in recieving system. Say if you are sending a currency which is not configured in the recieving system. You are sending INR and recieving system needs USD say. So data can not be posted.
Try posting a document in the recieving system with the same data, it will through the same error take help of any functional consultant and solve the issue.
Now go to we05 and edit the idoc replicate the same changes as you already found. and reprocess the idoc using tcode BD87.
Hope this answers your curiosity,
Award points if useful revert otherwise,
Aleem.

HP Toolbox has encountered an error and can not recover

I having a problem every time on boot up my computer. A box keeps coming up that says;
HP Toolbox has encountered an error and can not recover
Windows Version Win32NT - 6.1.7601.65536
HP ToolboxFX version : 006.015.01163
I've uninstalled and reinstalled the software, but I get the same problem.
The printer works great, but I just get this annoying prompt every time.
When I first installed the software a year ago when I first purchased my printer, I don't remember having ever having this error at that time.

D Carey, sounds like you are having an issue with the Printer Toolbox software. However, I am going to need to know more information on what you are working with. What is the operating system you are working on and what is the particular model of printer that is experiencing the issue? Here is a post by one of the forum regulars on what information is good to contain in a post so that we have enough information to give you the answer you need as immediately as possible :
http://h30434.www3.hp.com/t5/Other-Printing-Questions/Want-Good-Answers-Ask-Good-Questions/td-p/2094
Let me know and I will get right back in touch with you!
I hope you are having a wonderful week, and I hope that the weather where you are located is as beautiful there as it is here!
-Spencer

Getting an error prompt "the facebook server has returned an unknown error and is not able to fulfill your request. (2001)"

Hi. I need help regarding facebook for blackberry. I cannot post any status update, i keep on receiving an error prompt "the facebook server has returned an unknown error and is not able to fulfill your request. (2001)". it has been like this for the past 3 days. I already did the hard reboot many times, re-send service book though i do'nt think it's needed, and tried uninstalling and reinstalling the facebook application too but still getting the same error everytime i try to post a status update. I can comment to messages on my wall and other profiles, the news feed is updating in time too, i can also log-in and out to facebook with no problem, as well as other applications on my phone like foursquare, BBm, ubersocial, BB protect, BB app world, etc, are all working perfectly fine. And now I don't know what seems to be the problem.
I've already contacted my network provider and told me that the error i'm getting is beyond their scope.
Is anybody having the same problem as mine?
Can someone in BB support team help me regarding this issue and tell me what should I do?
Thank you in advance.

I got the same issue !! Since I've updated my Facebook app 2 or 3 week ago !
I can not update my status and check-in ! It gives me "the facebook server has returned an unknown error and is not able to fulfill your request. (2001) "
I can upload photo, put comment on people, like people status/picture. The news feed update perfectly !
I also tryied to uninstall reinstall the app, reboot etc etc ! I still can't update my status !!!! I've installed 3.0.0.17 this morning and the issue is still there...
I've remarked one thing... On my facebook under "privacy setting/the Apps, Games and Websites" I used to have a "blackberry app" installed. It's not there anymore and I didn't remove it.
I don't know how to reinstall it...

Error: Application document not posted

hi,
while posting IDOC into R3, I got below error in WE05.
under status records
51 Error: Application document not posted
Account group is not defined in table T077K
reward points always helpful for helpers.
Regards,
Nageswari

HI,
Check the posting program use call transaction, if no analyze the error message and fix the problem. If yes then debug your program step by step until you hit the error screen.
If error in IDoc data , then Exit the IDoc restart from BD87, else problem with application configuration, restart from beginning.
--related Data error contact your Functional team
Also see the below links
IDOc testing - /people/suraj.sr/blog/2005/12/29/generate-test-case-for-an-idoc-scenario
/people/sravya.talanki2/blog/2005/10/27/idoc146s-not-reaching-xi133-not-posted-in-the-receiver-sap-systems133
idoc erros - http://help.sap.com/saphelp_nw04s/helpdata/en/6a/e6194119d8f323e10000000a155106/content.htm
Regards
Chilla

Idoc number have status is 51 Error: Application document not posted

hi friend
i have error in idoc number status 51 Error: Application document not posted. basic type is ORDERS05 Purchasing/Sales
what i do for solve this issue
with regards
dinesh
Edited by: code acess on Feb 9, 2011 4:35 AM

Hi,
{1.how i check in the delivery documents have idoc number ? }
Go into the delivery, output. Check if any output has been triggered for EDI. If yes, then select the output and click on 'Process details' (it is the button just after communication where you give the print name). It will display the Idoc number.
{ what are the required for cofiguration of EDI. Pls Send me the configuration setting . i didnt have help here ..iam expecting configuration setting }
Though it is difficult to share all the config settings in this thread, what I will do is to put in a few steps which are general settings. Only a few things vary.
For EDI / ALE - Idoc the common settings are
a. The port should be enabled for sending and receiving the data thru Idocs. Usually basis does this.
b. Partner profile should be configured in WE20. Example if you are sending a sales order confirmation to ship to party then, You should set up a partner profile in WE20 for partner number in KU (Customer) folder. You can copy any of the existing customer. What you have to make sure is you have added the message type and the Basic Type in the outbound parameters of the partner in WE20. Also, you have to make sure that you are giving the output type and the process type as well.
This is same even when you are receiving the Idocs from customer. Say for example customer PO. However, instead of outbound, you will add all these details in inbound.
Similarly, if you are sending PO to your vendos, then, you have to make changes in folder for partner LS. There are so many other folders as well.
Check WE60/61 for the documentation for what is Basic types, Message types and segments. It is very important for you to know about these when you are dealing with Idocs. To start with, you can give Orders01 in Basic types in WE60 selection screen and read out the details.
c. Once the partner profile is set up, there is a table called VOE4. This is the table where you can maintain the customer cross reference for incoming idocs.
d. Output type should be set up for EDI trigger (Tcode NACE) . You can use the existing programs. You can Check BA00 which is normally set up for EDI trigger as well. You can try triggering that first. You may get some errors at first. But do not panic. Just read those errors and then search the form for errors. You will get to know the next step.
e. Once you have the above settings, I think you are pretty much ready for EDI... you can try these. If you get struck in between, the form is there to help you...
Hope this helps...
Regards,
Mukund S

When was unloading creative cloud came an announcement that Rhodesia that had an error and could not download the error code was 50 which means

when was unloading creative cloud came an announcement that Rhodesia that had an error and could not download the error code was 50 which means

Nobody can tell you anything without proper system info or other technical details.
Mylenium

At startup-system error and divide by zero

I've been having a lot of problems starting up my beige G3 mini tower, it has 233mhz, 384ram, mac os9.1. I've zapped the pram and held the shift key down to boot with extensions off, didnt work. I've changed the battery twice in case the first replacement was bad, it started up and ran long enough for me to trash all the preferences, I tried to change the extensions, but when restarting it was back to not completely starting up. I've tried pressing the button near the pci slots with the battery out, 30 seconds, waited 30 minutes and held down the button for another 30 seconds, replaced the battery, checked the sound card for looseness then at startup it worked till I changed the time and date. I tried the battery and button again this time waiting over night between pressing the button for 30 seconds, after startup I was able to run disc first aid and it said everything was ok, then crashed again when I tried to change the date and time. I've even tried booting up from command/option/o/f, I'm not sure what firmware is but it would try to start up that way,but was very slow with a os cd in the cd drive. I tried to erase the hard drive but I couldnt get it to start up from a cd, iv'e tried os9, the original cd that came with the computer and a system recovery cd.
Most times when trying to start it up it chimes, then the happy mac with a grey screen, then the mac os screen, then the bomb with "system error" and under that "bus error" under that it says to restart with extensions off. sometimes the button for restart will even work with the cursor. Once, after trying to start up after all the battery removal, pressing button near pci slots , pressing com/opt/o/f, extensions off, the screen getting to the mac os then the bomb dialogue, it said system error and instead of saying "bus error" it said "divide by zero". Thats the first and only time I've seen that one. Also, the grey screen (with the happy mac disc icon) now has horizontal lines with texture? that I havent noticed before.
got any ideas what I should do next? I probably wouldnt bother with my G3 anymore because I just bought a new Imac, but I have a vinyl cutter hooked to it, it has the old round serial port cables and I would have to buy new software, cables and dongle to use it with my new Imac, I also have illustrator, photoshop, scanner, and drawing tablet on my G3 that I cant use on my new Imac (intel) leopard.
Is my hard drive or motherboard dying? is there a way to find out if and what hardware is messed up? and if so, is there still still parts out there for this G3?

Hi, R1camper -
I ran disc first aid from the cd and and it said it couldnt fix-overlapped extent allocation,4,479.
That is a type of disk directory damage, one which Disk First Aid can not repair.
Alsoft's DiskWarrior can usually repair that kind of damage, with no loss of files. If you choose to go this route, suggest you call (or email) Alsoft's sales department, and request an older version of DiskWarrior - the current versions won't run on your Beige G3/MT.
However, if you can manage to live with the loss of files, you can probably replace the hard drive for less cost.
Your Beige G3/MT came with either an ATA (now often referred to as PATA and/or IDE) drive or a SCSI drive - it could have been ordered with either when the machine was new.
With luck it will be an ATA drive, since those are the least expensive and the easiest to install. Such drives are not Mac-specific - any ATA drive designed for internal use and of appropriate size will work. The only item of concern is to set the drive's jumpers properly. The drive should be jumpered as Master (it may come preset as Master or as Cable Select - Cable Select will not work on your model), unless it is a Western Digital in which case it should be set to Single if that is an available choice.
There is probably little to gain by getting a 7200RPM drive, especially if there is extra cost for one vs. a 5400RPM drive - the relatively slow internal bus speed on your machine will not be able to take significant advantage of a faster drive.
Re the RAM, if you have the time you might try replacing any you took out. Over time the contact the module makes in its slot can get iffy - removing and replacing the module usually fixes that problem, by wiping the contacts clean.

Error messages are not posted into ECH using collect method

In asynchronous interface, Error messages are not posted into tcode:ECH_MONI_SEL using collect method.
In the collect method, passing software component version,business process and error messages.but its not posted into ech and ppo.

Hi,
Have you created the FEH class for the proxy. In that, from within the PROCESS method, when there is an error you will be placing those errors into a table and this needs to be passed to the COLLECT method.
CALL METHOD i_ref_registration->collect
   EXPORTING
     i_single_bo      = input
     i_component      = 'ZSWC'   "Software component defined while FEH customisation
     i_process        = 'ECH_BP' "ECH Business process defined while FEH customisation
     i_error_category = lc_errcat
     i_main_message   = wa_error
     i_messages       = lt_error
     i_main_object    = wa_object.
Here while populating the wa_object, the objtype field should be populated with the object type defined while FEH customization.
If all these things are done, then this should post the error.
Regards,
Abijith

Hello, okay? On September 13 I bought an iPad and in October bought a game on the app store problem is that when informed the card number dropped normally, but then went on to ask for a new form of payment because one had given any errors, and so not lowe

Hello, how are you? On September 13 I bought an iPad and in October bought a game on the app store problem is that when informed the card number dropped normally, but then went on to ask for a new form of payment because one had given any errors, and so not lowered any other game and not upgraded the already downloaded. I do not know what exactly I have to do, because if informed a new payment method continues with the same problem, checked the card bill and really had given an error, because there was no billed the game. I ask you to verify what happened and explain to me what I need to do, because my single card is Visa's and do not intend to return others to use the services of the App Store.
Thank you for understanding.

I think you need the app store support. http://www.apple.com/support/mac/app-store/contact/ Go there and use one of the methods to contact them about your issue and they should be able to help you out.
This forum isn't checked by Apple employees but is for users to help each other out.
Phil

HT203175 Running Windows 7 64, when installing, I get the error, 'itunes encountered an error and could not configure'. Ideas?

Running Windows 7 64, when installing, I get the error, 'itunes encountered an error and could not configure'. Ideas?

iTunes unknown error 13010

Application Error, System Error and Error in SXMB_Moni

Dear PI Gurus,
I am kinda new to PI(XI) environment, and my self confused when I try to search failed messages in XI. I saw in Status group, there is Application Error, system Error and Error under SXMB_MONI. And I am wondering what is the different between these errors. Worst to come it all errors, Why we do have this separated errors? Can anyone tell me, what is the difference between this errors?
Thank You
Regards
Ramesh

Hi
- Application Error related to SOAP
just look at tgis Blog
/people/jin.shin/blog/2007/05/21/handling-web-service-soap-fault-responses-in-sap-netweaver-xi
also look at this Thread for SXMB_MONI-system error occured
SXMB_MONI-system error occured during persist
Regards
Abhishek
Edited by: Abhishek Agrahari on Jan 21, 2009 7:48 AM

System errors and replys not posting

Similar Messages

Maybe you are looking for