Tabel control - amount not correct for currency

Hi all
I m having a slight problem with a table control. First this is my table:
MANDT             MANDT
INVID             ZIC_INVID
INVLINE             ZIC_INVLINE
.INCLUDE     ZIC_ITEM
.INCLUDE     ZIC_GLACCOUNT
.INCLUDE     ZIC_MATERIAL
.INCLUDE     ZIC_FI_ITEM
I have different includes in my table, because I have more then one table control, but everyhing is related so i work with includes.
In one of the includes i have an amount and currency.
First the amount is for example 1,00 and the currency is EUR. if i should change this to JPY i expect that the amount should change to 1 JPY like in transaction fv60, but this is not the case.
In my table i have a reference of my amount to the currency.
Also in the table control i have a reference. Is there something that I m missing?
thanks
Message was edited by: Kristof De Bruecker

Peluka
I changed the attribute to 'CURR' and changed in my table the reference table and field and this works but...
when first I have an amount of 1,00 EUR, changed the currency to JPY, i get now automaticly 100 instead of 1.
Is this normal? What can I do to change in automaticly to 1?
Message was edited by: Kristof De Bruecker

Similar Messages

Issue when installing SQL Server Express 2012 - "The requested control is not valid for this service" + "Could not find the database engine startup handle"

Good morning,
I'm experiencing the following issue when installing Microsoft SQL Server Express 2012 (with tools, SQLEXPRWT_x86_ENU.exe) on the laptop of my company;
Installation goes plain until around the end of the progress bar, it stops on the setup of
SqlEngineDBStartConfigAction_install_configrc_Cpu32
giving 7-8 times, even pressing "Cancel", the message "The requested control is not valid for this service";
After this, I receive one last message ""Could not find the database engine startup handle", then installation ends with failures, in particular the Database Engine and the Server Replication failed to be installed.
I've put in my SkyDrive the error log I received after the install;
I'm at full disposal if you need further information,
thank you in advance
Best regards
Francesco

Well, i just ran into this issue and the problem was lack of admin rights. It was my company's laptop so got the setup initiated by my company's IT team with admin rights. However, the upon completion of setup, i go the same error messages as stated above:
SqlEngineDBStartConfigAction_install_configrc_Cpu32
giving 7-8 times, even pressing "Cancel", the message "The requested control is not valid for this service";
After this, I receive one last message ""Could not find the database engine startup handle", then installation ends with failures, in particular the Database Engine and the Server Replication failed to be installed.
Also, if you open SQL Server Configuration, the status of the service is "Change Pending" and you would not be able to set the startup login type to Local Service/System/Network.
Then, I just got my account added as Local Admin and then tried to start the service and was able to.
However, I am not sure whether same was the case for you.
Please mark the answer as helpful if i have answered your query. Thanks and Regards, Kartar Rana

Artwork on my iPad does not match iTunes and is not correct for movies, TV Shows Nd some songs

Artwork on my iPad does not match iTunes and is not correct for Movies, TV Shows and some songs & Albums. Is this issue resolved? If so what was or is the fix. I have not been successful in locating that. I found posts stretching back into late 2010.

most of these items were downloaded from eihter iTunes or in the case of movies, imported into the app and then loading them to TV Series or Movies as appropriate. They were all fine until about two days ago when I did a sync. Then the artwork went haywire. I tried manualy removing and replacing the artwork in iTunes with the correct jpg's. and then re-sync. iTunes shows everything OK, but the iPad is the one with it all messed up.

Apple ID username, password not correct for imessenger ios 6

i just upgraded to ios 6 on my iphone 4 and imessenger is fine to send and receive but when i go to settings and try to register it with my apple ID i get an error that the username and password are not correct, although i am usung the apple ID fine in app store for example. anyone knows what this is?
also, i was wondering, while setting up my iphone after the upgrade to ios 6, in one of teh steps when i started using the phone, it asked for teh apple ID password to do soemthing related to icloud, imessenger and facetime. it also gave the option on the phone screen to "skip this step" which i did, i skiped the stem and thought if i wanted to i can go back and do it manually from the settings any time. i think it was something related to downloading new features for the icloud. i messenger and facetime.
could this have been the case? but i mean if i had the option to "skip the step" it means that it is not something drastic and can always be done manually later.
anyone has feedback?

Hi again, well I can't answer that question, because my computer IS asking for my apple ID and password to install Rosetta Stone. I would have appreciated you taking the time to help me, if you had had any advice for me. Since I posted this, I have found the answer so I don't need your time anymore, however. I eventually went to my settings and SET a password, which solved the problem. I recently reset my computer and all my records had been wiped- I was unaware that my computer settings had deleted my old password which had been saved on it- not realizing that its data would be seperate from the other numerous places I have used it the past week since I got it back. An answer that would seem like a no-brainer, but since it hadn't needed to be done until then for any other previous installs since the reset, it appeared last on my to-do list.

Delivery qty not correct for partial delivery

Hi, I met some issues need your help!
1) Create a sales order base on the sales bom.
2) Current stock and supply is not available for the required delivery date.
3) According to the current stock or supply qty.only confirm partial qty for the components.
    eg.
    the structure of this sales bom as below:
    Material: A 1PC --> B 1PC
    Material: A 1PC --> C 1PC
    After ATP check ,the result as below.
    item 10   mateiral A (Header)          100PC   ( not relevent for inventory)
    item 20   mateiral B(component)     100PC   confirmed 30PC
    item 30   material C(component)     100PC. confirmed 10PC
4) Create delivery(partial delivery) with the selection date.
5) We can find the component quantity is correct but the header quantity is incorrect.

Hi
Configure the field 'Create Delivery Group' in the item category of BOM (VOV7) in the Bill of Material/Configuration area. Please go thro the F1 help details of that field..
Form delivery group and correlate BOM components
Here you can determine whether sub-items that belong to a main item, and which resulted from a BOM explosion, are to be combined in a delivery group.
Use
You use a delivery group to determine a common delivery date for all the items that it contains. If you double the quantity ordered for the main item, then the order quantity for the sub-item will also be doubled.
Indicator X means that a delivery date is created for the delivery group. The system uses the last date (chronologically) of an item in this group to create the schedule line date.
Indicator A means that the system generates correlated schedule lines. If no complete delivery is required, as soon as all the items in a bill of material are available, the system creates a correlated schedule line. On the first date, when all items in a bill of material are available, a confirmed quantity is issued.
Thanks,
Ravi

Validity slice is not correct for non-cumulative cube

Hello Expert,
There are two non-cumulative cube, say cube1 and cube2. Cube2 has only one more dimension of PLANT than Cube1.
Cube2 is copied from cube1 and change the char of validity.
Cube1 & cube2 use the same fill data source. That is, first load with opening balance and second with delta.
char of validity for cube1: calendar day & material
char of validity for cube2: calendar day & plant.
The query based on cube1 works well. To say cube2, the validity slice(in TXN RSDV or TBL /BIC/TCUBE2) is not correct. There is only one record which contains BLANK plant.
There are plants in F table.
I tried the following steps to recovery the validity slice, however, it made no sense.
1) PGM RSDG_CUBE_VALT_MODIFY to rebuild the validity slice structure
2) FM RSDV_VALID_RECREATE with I_REBUILD_FROM_FACT = 'X' to create validity slice from fact table.
Would you please suggest?
Thanks
XY

Hi XY,
For sure, running the RSDV_VALID_RECREATE function module in SE37 will recreate the validity table. And you can use the parameter "X" in the parameter I_REBUILD_FROM_FACT if the entire fact table should be read.
Also, to change the validity slice manually in tcode RSDV you should:
- overwrite the column 'To mode' with a 'F', which mean Fixed
- & then the 'Fixed to time' with your new value.
There is a program which allows you to modify it: Program > RSDG_CUBE_VALT_MODIFY
At
Nadja Xavier

Infotype Screen Control (T588M) not working for additional fields to contro

Hi,
I have a requirement to enhance IT 0002 with fields LNAMR, FNAMR and CNAME. Also field preferred language.
I have included LNAMR, FNAMR & CNAME as additional fields in the Include Screen 2040 elements, lay editor and maintained table T582c where i have assigned enhancement to the standard screen. These fields are getting displayed in infotype 0002
But the issue is Infotype Screen Control (T588M) is not working for these fields to control the display or hide.
Has any of you come across this issue? what could be the reason for this issue? Please suggest ASAP.
Thanks in advance.
Regards

Hi Experts,
Please help with your inputs and suggestions.
Regards

Application Server Control does not ask for password

Hi all-
I just installed App Server (as part of Collaboration Suite) and am working on security. For some reason, the App Server Control for the apps tier does not ask for a username/password. Anyone know how to fix that glaring hole? Infrastructure does ask for user/pass, just not apps.
Thanks!
Rob

I had to clear authenticated sessions AND cookies (in Firefox). Clearing only one or the other isn't enough.
Rob

Torque control is not working for my system using analog feedback

In the test bed, we are testing a brushless DC motor and a load motor generates torque to the test motor. The test motor is running with torque control scheme. They were connected together and I measured the torque signal to feedback the signal and control it. However, I just realized it only control when the torque was static. If I commanded a certain torque value (in this case, counts command), it kept generating that value. However, it did not generate the same torque in different position. I heard NI motion controller could develop torque values by mapping the torque signal with encoder signal. If it's true, the torque generation based on analog feedback, also, needs constraint by rotor position, right? W
hen I turned on the load machine with constant speed (50 RPM), the torque from the test motor did not provide the constant torque that I commanded. It generated the fluctuated torque values. This means the max torque was generated at one point and decreasing by rotating the shaft and increasing the torque. Keep going in this way. Could you please tell me if this is the correct response when we are using analog torque feedback?
Thank you.

Try the following:
1.-Set your test motor to encoder feedback instead of analog feedback.
2.-Load a velocity move on the axis for the test motor.
3.-Set the following error limit on you axis to 0 (disable following error).
4.-Use the load torque limit function to limit the amount of torque the 73xx PID loop will generate,this value is in volts, so you will need to do a correlation between the voltage output from the controller and the torque reported by your torque cell.
5.- Start the load motor.
6.-Engage the cluch.
7.-Start the velocity move on the test motor, you will see the torque ramp up to the torque limit.
8.-Call the load torque limit function on the fly to vary the torque setpoint to where you want it.

BPC75NW - Periodic Amount Not Calculating for records with blank YTD value

We are on BPC75NW SP6 and have a YTD consolidation application. Data is loaded on a monthly basis uising a process of importing data files from supplying systems and then loading them into BPC using the data manager append function with a transformation file. YTD amounts are as expected and 'most' periodic amounts are also calculated correctly via MDX mesures in reporting. However, in situations where we have a P&L YTD balance in one month (say January) and then in the next month (February) there is no longer a YTD balance in that P&L account, no record is loaded for February YTD and the system is not calculating any February periodic amount. Example:
January - Load $100 to a P&L Account which is the YTD amount
The January YTD amount = $100.
The January Periodic amount = $100.
February - Load no record to the same P&L account as above (as the YTD amount is now 0)
The February YTD amount in the system is blank
The February Periodic amount in the system is blank (This should be a NEGATIVE $100)
As a possible work around we have also tried to load a 0 to February. The data manager package shows the record as loaded successfully but since it is a 0 it really does not put it into the database.
Surely someone out there has already hit this situation and is willing to share the solution.
Thank you,
Vicki S.

This problem was resolved by installing SAP Note 1405993 - MDX: Error: Invalid MDX command with
CURRENTMEMBER. The current text on the note does not describe our error but SAP will not extend the text to cover this issue.
Prior to installing this note, the following other notes were also installed but they did not fix the periodic calculation issue. Under SAP's advisement we are going to leave them however as 'they should not have any side effects':
1529720 MDX: No data for calculated member and metadata reference
1590976 MDX: Incorrect data for IIF
1584196 MDX: Calculated members and different dimensions
1528374 MDX: System error GET_PRPTY_VALUE-02-
I will now close this message.
Vicki Shrontz

Business Transaction Control is not Working for Equipment Status.

Hi All,
I have created a Status Profile for Equipment / Functional Location & assigned 5 Status under this Profile i.e. NEW, COM (Commissioning), INS(Inservice), CAM (Care & Maintenance) & DCM (De Commissioned). For Status DCM i have assigned Transaction control FORBIDDEN for "Enter PM processing data , Enter PM planing data & Create Meas. Doc."activities.
It Means, whenever user creates Plant Maintenance Order OR Notification, Maintenance Plan OR Maintenance Item & Measurement Document for any Equipment / FL having this user status (DCM), system should not allow creation of above mentioned object.
In my scenario, system is giving an standard error message " The business transaction cannot be carried out" during creation of "Plant Maintenance Order OR Notification, Maintenance Plan OR Maintenance Item".
But i am able to create measurement document for equipment / FL having user status DCM with Transaction control Forbidden of Measurement document creation. No error message displayed by the system.
Can anybody tell me why its happening? Why system is giving error during order & plan creation but not for Creation of measurement document ?
If this is not posible in standard SAP, does any body knows about any OSS note so that we can implement the same to get an error message.
Thanks in advance
Arun

Please ensure whether both projects have the same budget profile. Other than that you need to carefully investigate how the cost was posted onto both projects in the first place. Please note in case of procurements, budget is only checked at the commitments level (search the forum as this has been discussed before).
In case this does not resolve your issue, revert back with the budget profile settings.
Regards,
Ammar

F4 help not showing for currency translation types

Friends,
I have a scenario where I need to convert currencies in my query based of different tranlastion types. I maintained a variable in RRC1 and it's working fine when I execute the query. It asks for the variable - shows different available options under F4 help and calculates the results as expected.
Now the problem I am facing ....
When I have exceuted the query and want to select a different translation type using context menu on any amount field, it gives me only one option "Average rate for the current date". I am expecting all the available translation types to choose from, here as well.
Can someone help me with that?
AK

Anybody out there ???
AK

Printed Document not correct for RH7 Word

I need help with the pdf print function. So far everything appears to working perfectly and thank you who have helped me get to this point. I am now trying to use the "Prined documentation" function of RH7 and have a few issues:
1. I am getting blank pages and do not see them in Word. Where are they? How do I remove them?
2. I have a page in Word but it does not print to pdf, I think it just might be one of the above blank pages that is not printing.
3. I am also having difficulty with the setup as far as TOC and Chapters do not match. I will review other discussions.
Everything appears correct in Word so there is something in the outline I don't yet understand or somewhere else. I cannot see page breaks except for those in Word and they appear to be correct.
Suggestions? Ideas? Help?
Thank you

Ok, I did try your suggestion and it does create a Word file. However, the Word file has the same results as the pdf so there is something else I am missing with this process. Here are a few "clues" if you will:
1. Both pdf and word create a TOC that looks good
2. Both create the documents alike
3. One of the issues is that the first half does in fact put a separate topic on each page, which I selected in both pdf and word
4. Then somewhere in the middle topics appear on the same pages. I did check the headings and they do match all the way through.
5. The bmp RH& Word inserted images are not all visible...some are some are not but all images that I copied and pasted in to word are visible.
6. At the top of the pages for both pdf and word there are Book titles, page titles, some document name titles and then on the upper right corner there are a few section / book titles. This is very inconsistent.
7. Links are not printing consistently in double underline green which is how I have them all set, but different colors, usually black and some are not underlined.
8. The page headings are all smaller print verses the Heading 1 design I set, but the individual headings that fall underneath are mostly correct.
Examples, [(my comments are within ( )] although there is additional spacing in the copy process:
Apply to all Sections in Data Capture Operations (This is actually a book in help and should be Helvita 14 Bold)
Data Capture Operations (This is the head and should be like this)
Below is a view of the opening page options within the Data Capture module and the quick links that correspond to each function within this module. You may not have access to all of the functions listed and those will appear Grayed out if you do not have access.
(This should be an image and it was added through RH& Image)
Initial Filing
Incomplete Initial Filing (These are all links and should be like the top one with double underlining)
Incomplete Supplemental
Supplemental
Modify/Delete Crash Report
With this said, my 2 outstanding issues are:\
1. Separate pages for each topic
2. Visibility of all images on the pdf. Word not as important.
Hope this helps explain the issues and gets me to resolution. I feel it is simple, I just can't put my finger on it!
Thank you for helping.

Render control file not valid for" project.aep -- Please Help!

I'm using AE CC
I've read all the discussions I could find on this topic to fix this problem.
All my computers are mapped correctly. The file that I'm sending at this point is very basic. Once jpg sequence (as a test) name shadowMatte - no spaces, underscores, very basic.
-The file is set for multimachine rendering in render queue
-I collected files with 'Collect Source Files: None' , Enable 'Watch Folder' render' checked
I'm not new to using multi machine rendering, this time around I just can't seem to get it to work...
all render slaves at least 8 gigs of ram.
Any help on this matter would be GREATly appreciated.
- Max

> "Hello - is there any one left at Adobe to help with this? "
This is a user-to-user forum, where people help out in their free time. If you want a guaranteed response from Adobe personnel, contact Adobe Technical Support:
http://www.adobe.com/support/contact

Uploading files Mime Type not correct for Office 2007 default extensions.

hi all,
My company has recently moved over to MS Office 2007 and the default extensions for word, excel etc are now .docx, xlsx etc (ie xml based).
Unfortunately now when we upload files through APEX to the database the MIME TYPE value for these files isn't being recognised and not loadeding correctly into the APEX_APPLICATION_FILES table and subsequently any future retrieval of these files fails.
I could put some logic inthe up load procedure to look at the filename in APEX_APPLICATION_FILES and hard code in the releavnt mime types but this still causes problems when retrieving the content.
Has anyone come across this and got a workround? Is it a bug in AE?
regards
James
FYI - using APEX 3.0.2 over 11G.

I have not any response to my question and not sure if it is in Apex I need to look or the tomcat server that I need to look. I have a useful application to try to show others what Apex can do for our customers to collaborate. However, most of our customers are using office 2007 so, hoping this is possible.
I am using apex 3.2.0.00.27 if that helps someone to point me where to find more info on being able to have Word 2007 or excel 2007 fire up to open a .docx or .xlss file stored in a table blob column. Word or Excel does fire up to open .doc and .xls files.
The following is the query for a report selecting the filenames uploaded into a blob column in my table:
{ SELECT s.ID, SUBSTR(s.NAME,INSTR(s.NAME, '/',1,1)+1,length(s.NAME)) SHORT_FNAME, s.SUBJECT
FROM spp_attachments s
WHERE s.PROGRAM_ID = :P2_PROGRAMID }
Below is the stored procedure called from the link on the short_fname column in report query above.
{ create or replace PROCEDURE download_file(p_file IN number) AS
v_mime VARCHAR2(48);
v_length NUMBER;
v_file_name VARCHAR2(2000);
Lob_loc BLOB;
BEGIN
APEX_APPLICATION.G_FLOW_ID :=245;
IF NOT (wwv_flow_custom_auth_std.is_session_valid) then
owa_util.status_line(404, 'Page Not Found',true);
return;
else
SELECT MIME_TYPE, BLOB_CONTENT, name,DBMS_LOB.GETLENGTH(blob_content)
INTO v_mime,lob_loc,v_file_name,v_length
FROM spp_attachments
WHERE id = p_file;
-- set up HTTP header
-- use an NVL around the mime type and
-- if it is a null set it to application/octect
-- application/octect may launch a download window from windows
owa_util.mime_header( nvl(v_mime,'application/octet'),
FALSE );
-- set the size so the browser knows how much to download
htp.p('Content-length: ' || v_length);
-- the filename will be used by the browser if the users does a save as
htp.p('Content-Disposition: attachment;
filename="'||replace(REPLACE(substr(v_file_name,instr(v_file_name,'/')+1),chr(10),NULL),chr(13),NULL)|| '"');
-- close the headers
owa_util.http_header_close;
-- download the BLOB
wpg_docload.download_file( Lob_loc );
end if;
end download_file; }
Thank you,
Mark

Tabel control - amount not correct for currency

Similar Messages

Maybe you are looking for