Tactic 3D rage wireless volume change

I just bought a tactic 3D rage wireless headset, charged it up, installed the control panel and the firmware from the creative website, and it's working well. However every time I adjust the volume on the headset it bleeps, which is very annoying. How do I disable this?

Hello Zenna,
Welcome to the forum!
There is no way to disable the beep sound. When adjusting the volume with the rotary dial, you will get an audible beep tone as an indicator.

Similar Messages

Tactic 3D Rage Wireless V2 connecting issues

"There is no supported audio device available" it says.
I've already done the initial 8 hours of charging and I've used them for 2 days of slight gaming before they ran out of power. Now that I was going to charge them via USB ports (Tried both 2.0 and 3.0 -USB ports) it just didn't respond to anything. No red blinking light, no nothing. And as I mentioned, it only says "There is no supported audio device available" which really pisses me off. I've reinstalled the one and only driver for my headset/operating system 3 times, which also pisses me off really good. So basicly, it worked the first time i charged it, not the second time. It's a brand new headset, got it last wednesday, which pisses me off the most.
Help out this pissed of guy would you?
Kind kind kind regards Alfons ( )

Originally Posted by Afhene
The headset is now detected, strangely since i haven't touched the wireless transmitter at any point. Still, it just doesn't charge. I remind you once again. I charged it once.. the initial 8 hours was painless. I do have a clue for you though. When I restart my computer with USB-charger being put, it says " keyboard: 2, mouse: 2, hubs 2..... shutting down in 15 seconds" and it shuts down as promised. I remove the USB-charger from the USB-port and it does the regular start up. I've tried every single USB-port (I've got 10 of them) and I am still pretty pissed of to be honest. I'll keep saying that until it gets solved, take no offence Creative Employees (unless you've developed this ga***ge).
EDIT: Not sure if it's entirely connected though. Playback Devices sounds setting says "No jack information available" when I look closer into the headset's properties in there.
Somewhat kind regards Me ( )
Hi Afhene,
There is no jack information available for the Tactic3D Rage Wireless. Please avoid charging the headset via a powered USB hub. Connect the headset direct to the computer's powered USB port.
Since your headset is now detected, you can launch the SB Tactic3D Control Panel and look for the battery level indicator of the headset after it has been paired to the USB wireless transmitter.
battery_indicator.jpg
I suspect that your headset is already fully charged when you did the initial battery charging of 8 hours. Hence, there is no response on the Power LED when you charge the headset for the 2nd time. During the battery charging, the Power LED will blink and stops blinking when it is fully charged.
Power LED (blinking) - charging
Power LED (off) - fully charged; power off state
Power LED (solid white) - fully charged, power on state
If you like to learn more about charging Tactic3D Rage Wireless, you may refer to this article:
http://support.creative.com/kb/ShowA...spx?sid=111092
You may opt for firmware update of the USB wireless transmitter & headset and observe situation can be improved. Please follow the instructions carefully.
firmware_update.jpg
Cheers,
JL-CL

Tactic 3d Rage Wireless Possible USB Transmitter Problem

Hi guys,
It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
Many thanks in advance.

Originally Posted by Xotli
Hi guys,
It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
Many thanks in advance.
Hi Xotli,
Do you encounter any error(s) during the firmware update of the headset and the USB transmitter?
Do not connect it to the USB hub. At any one time, the headset and USB transmitter cannot connect together during firmware update; only separate update is allowed.
Here's the instructions given for updating USB transmitter via Windows:
- Download the file onto your local hard disk.
- Ensure that your Sound Blaster Tactic3D Rage Wireless Transmitter is connected to your computer.
- Ensure that the Sound Blaster Tactic3D Rage Wireless Headset is removed from your computer.
- Un-compress the downloaded file to a folder in your local hard disk.
- Double-click <SBTR_PCFW_US_TX_1_59_140721.exe> from the folder which stores the uncompressed files.
- Follow the instructions on the screen.
- After the installation of the firmware is completed, unplug and plug in your transmitter and start pairing with the Sound Blaster Tactic3D Rage Wireless headset again.
Cheers,
JL-CL

Adjust balance volume Tactic 3d Rage Wireless

Hi. Hearing problems on one of my ears, so i need to adjust the balance on my headset. I don't have this option in properties. http://i.imgur.com/WjnG3Sm.png
Also, this option is not in the software provided by Creative.
Does anyone have a solution for this, or is it only me who is having this problem?
Thanks for any help

Originally Posted by k_flaathe
Hi. Hearing problems on one of my ears, so i need to adjust the balance on my headset. I don't have this option in properties. http://i.imgur.com/WjnG3Sm.png
Also, this option is not in the software provided by Creative.
Does anyone have a solution for this, or is it only me who is having this problem?
Thanks for any help
Hi k_flaathe,
You may want to go to the window control panel, select sound properties of your sound card to adjust the balance.
If you still encounter issue with the headset, , you may want to relay your concern to Tech Support (link HERE).
Do make sure to explain the faulty behavior of your concerns and action taken as much as possible
Cheers !

My tactic 3d rage wireless wont turn off

So i today got this headset and it was working fine for a while, but after i installed the Sound blaster Tactic(3D) Control panel it suddenly stopped working and now i cant even turn power off from headset.
Windows shows that i've connected to headset and i should hear sounds. I also tried to pair with receiver, but nothing happened.

Same here. I think it's their server(s) problems

Tactic 3D Rage Wireless transmitter soft bricked

Hi guys,
When i was flashing TX firmware, transmitter unplugged then firmware installation was interrupted. Now wifi transmitter doesn't work.
Followed instructions;
Turned off headset
Ran transmitter firmware (SBTR_PCFW_US_TX_1_58_121101)
Then firmware installation was interrupted
Now the light on the wireless transmitter was no longer on
I think wifi transmitter bricked. How can i fix this problem Can anybody help me ?
btw, sorry for my little English.
Thanks in advance..

Originally Posted by bluxe
Yes I tried to install firmware several times but in no way does not install.
I tried plug-in the transmitter directly to my computer as you say. (already I don't have "usb hub")
always i got "cannot detect the device" error.
My problem isn't a hardware problem, completely software problem as I wrote in my first message
Bluxe, If your transmitter is dead and not detected, there is no way to run the firmware update. I suggest you contact technical support here for RMA.

Tactic 3d rage wont turn on

Hey i have a Sound blaster tactic 3d rage wireless and i tried to update the drivers the other day, this resulted in the headset being in a "on mode" which means i couldn't turn it off or do anything with it so i let the battery die and started charging it again when i put the charger in there is a faint redness on the mic button so i knew it was getting power but the head set still wont turn on so i left it for a few hours and i still wont turn on.
Anyone know anything that could help me?
Any help is appreciated,
Cheers.

Originally Posted by Orkneyspanda
Hey i have a Sound blaster tactic 3d rage wireless and i tried to update the drivers the other day, this resulted in the headset being in a "on mode" which means i couldn't turn it off or do anything with it so i let the battery die and started charging it again when i put the charger in there is a faint redness on the mic button so i knew it was getting power but the head set still wont turn on so i left it for a few hours and i still wont turn on.
Anyone know anything that could help me?
Any help is appreciated,
Cheers.
Hi Orkneyspanda,
Welcome to the forums!
Is your case similar to this thread?
- 3D rage headset not recharging with pulsing blue light
Cheers!

Sound Blaster Tactic Rage Low Volume Microphone

Hello,
I've recently purchased the Sound Blaster Tactic 3D Rage, and have found that the microphone volume is extremely low despite updating drivers and setting microphone volume to 100. The quality of the microphone is acceptable, it's just the volume is low, whether its in Windows, or Skype.
Thanks,
Royal-Mist

Why don't you try to get the sound from your TV's 3.5mm headphone out or RCA output instead and use your TV's volume control to increase the volume. But you have to output your sound from your PS4 to your TV via HDMI.

Main "Play Control" volume changes on its own when I open and close WinDVD or Winfast

Main "Play Control" volume changes on its own when I open these programs, and when they're closed the main volume resets to where it was before the program was opened.
Surely I'm not the only one who has had this problem before.. I've had the problem with both Creative soundcards I've owned, before and after different drivers installations.
It can be very irritating and can potentially lead to damaged speakers if I'm not paying close attention to what my various volume knobs are set at before and after I open these programs.
I appreciate any and all input, thankyou.

I had to edit to reflect its Mavericks 10.9

So in the last few days I've noticed that pressing my volume change keys actually isn't changing the volume on my macbook pro at all. When I press the volume up or down keys, it makes the recognisable pop sound but stays at the same volume while the squar

So in the last few days I’ve noticed that pressing my volume change keys actually isn’t changing the volume on my macbook pro at all. When I press the volume up or down keys, it makes the recognisable pop sound but stays at the same volume while the squares go up or down. I mute it but my computer still makes sound. It’s the same with the volume control up the top of the screen, too. I slide it up and down and it doesn’t change the volume at all. The only way I can change the volume is with my speakers or the program I’m in (iTunes, VLC etc). I restarted and it seems to be okay then I go to change it a couple minutes later and it’s back to not working again.
I’ve checked my settings- the “use all F1, F2, etc. keys as standard fuction keys” is not switched on, and I have tried a suggestion of moving the com.apple.systempreferences.plist file out of the library and onto the desktop and restarting and neither of those seem to make any difference whatsoever. I’ve tried to find online forums but the only suggestions I found were those two and they didn’t work.
I’m just annoyed because I usually have the worst luck with technology but my macbook had been going strong and I got it because of the apparent lack of things that could go wrong, but of course even if there is one thing that could go wrong it will happen to me.
Please help!

You migh give resetting your NVRAM a try:
http://support.apple.com/kb/ht1379

I have my iPhone 4s plugged into a dock and the dock connected to an amplifier, the problem is that the amplifier doesn't have a volume changer and when i plug in the iPhone into the dock the iPhones volume bar disappears. how can i change the volume?app?

Hi
I have my iPhone 4s plugged into a dock and the dock connected to an amplifier with 2 speakers and a bass, the problem is that the amplifier doesn't have a volume changer and when i plug in the iPhone into the dock the iPhone´s volume bar disappears and im not allowed to change the volume and its very loud. how can i change the volume? is there an app? any ideas??(my dock doesnt have infrared remote controller )
TY!!!!

Kline25 wrote:
So even if I just ask to pay them to replace the lock button they won't because my screens are third-party?
Apple does not repair devices beyond replacing the screen on some models or a battery replacement. They replace the ENTIRE device.
For the Out of Warranty replacement cost, you could have gotten a fully functional replacement device. Instead you chose to spend less to get only the screen replaced and continue to live with additional issues.
Apple will not touch the device now. They will know that it was opened elsewhere and that the replacement screen is not original.

Opportunities with volume changes

Our company has opportunities that can bring in revenue over several months, quarters, or even years. More often than not, a volume trend will be associated with the revenue.
Is there a way to properly forecast the volume changes within a particular opportunity, or do I need to have our sales team create a new opportunity each time the the unit volume adjusts?
For Example:
Opportunity XYZ:
Q1 2009 = 1000 units x $1 = $1000
Q2 2009 = 2000 units x $1 = $2000
Q3 2009 = 3000 Units x $1 = $3000
Q3 2009 = 1500 Units x $1 = $1500
Thank you in advnace for your help.

Thank you for the feedback. Yes the product revenue object will address my needs. However, its not very intuitive for the sales team to use. The opportunity has sales stage, the revenue has sales stage... they both have closed dates. Its somewhat of a mess to get people up to speed. I have found it much easier to not use the revenue object and keep it simple within the Opportunity details.

Wild volume changes thru Home Theater System

I have a Sunfire Theater Grand system hooked up by HDMI cable from DVR to HT. HDMI from HT to TV. Optical Audio from DVR to HT from HT to TV. For some reason I am getting large volume changes. It seems to be switching from stereo to Dolby Digital would be my guess. An easy example that really bugs me is that when i watch the local news the dolby digital comes through perfect then we go to national news and the audio I believe must go to stereo because the center channel is non existent. This also happens when watching shows and then a commericial comes on and blows you out of the house. Is there any way to have the audio transmit the same for all reception? I didnt have this problem with Dish Network. This is so frustrating.

Edvander wrote:
Acutally the audio is digital on all channels (not switching to stereo). It just has huge volume changes between programing and commercials. Pretty frustrating. Does anyone else have this problem?
There could be two issues at work. The first is how your receiver decodes and outputs DD2.0 vs DD5.1. The second is relates to the audio levels on the channels themselves, including whether or not the content is encoded with dialogue normalization
It is very common for channels to insert commercials at higher volume levels. Sometimes this is done on purpose, and other times it is a specific to the settings on the commercial insertion equipment and/or the encoded levels on the commercial source. Verizon passes most video and audio as is, so many of the differences you hear are due to the source content. On most channels, Verizon does not process and adjust the audio levels as DirecTV and Dish Network do.
You might check to see whether your processor has a dialogue normalization setting. Most Dolby Digital 5.1 programs are encoded with a dialogue normalization value, which is meant to equalize volume between DD5.1 encoded content on a particular channel. When this setting is enabled, it usually serves to reduce the volume levels on DD5.1 programs encoded with dialogue normalization, and then you may hear a volume spike when you are hit with commercials and other channels that are not encoded in that way. If dialogue normalization is already enabled on your receiver, you might disable it add and observe the difference on your system.
Some newer receivers do have a built-in audio adjustment feature (ex: Audyssey Dynamic Volume, Dolby Volume). This is meant to equalize the volume levels across different channels and sources, much like DirecTV does with their signals.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.

Tactic3D Rage Wireless Constantly Turns Off while Charging

I got the Tactic3D Rage Wireless a couple of years ago and it has had many problems from the time I received it. I eventually got the others fixed, or mostly fixed, but this one has been annoying me increasingly in the past few months.
The headset not only rapidly connects and disconnects with Windows 8 (I think it is a problem with windows and not the headset for this one), but it also turns off the second I turn it on while charging. This makes the headset completely useless when I am charging it. This would not be as bad, but now the headset will not actually charge when it is on its charger. After it "charges" for a few hours, I take it off of the charger and I immediately begin to hear the beeping, notifying me that the headset is low on battery.
I finally made an account on these forums after a couple of days failing at searching for this problem with others so now I am posting this. Help is greatly needed for I don't want to be forced to spend more money on another headset if I can get this one fixed. Please reply with any questions I have not answered, and have a good day.

Hi Logo594
You may want to refer to this article, specifically the last paragraph of the article regarding charging.
http://support.creative.com/kb/ShowA...spx?sid=111092
You also mentioned that this headset is at least a couple of years old, so it is possible that the battery
does not hold its charge well. If this still does not work, You may contact Support here.
Cheers,
Colin-CL

Sudden volume change in a region

Hello all--
I am doing a piece that's quite repetitive, using 2-measure regions that I have repeated as needed doing option-drag. On one track, one region, and one only, has a huge volume jump; I'm talking about 10-12 db! I can't find anything to account for it. Velocities are all the same, nothing done in the mixer (though the volume change is registering loud and clear on the fader). Is there something I'm missing? I could dip the fader using automation for this region, but that's a workaround, of course, and besides, since I'm a relative newbie, I'd like to learn something if there's a more "elegant" solution.
Thanks in advance!
later,
John

Hi again--
I fixed the problem with a gentle hint from over on Dave's Logic Pro Help board. I had done a real Stupid Newbie Trick: accidentally dragged one region on top of another identical one, therefore intensifying it! Duhhh... Well, it might be good to have a way of seeing that's happened, since it doesn't show up in any obvious way in the Piano Roll Editor or the Event List. But I'm not excusing myself. Live, admit stupidity, learn... Onward and upward!
later,
John
PS Ben, there are more Tenneys than you might think! In fact, there's another John Tenney (my full name) who's also a musician! (not a professional violinist like me, but still...)

Tactic 3D rage wireless volume change

Similar Messages

Maybe you are looking for