Adjust balance volume Tactic 3d Rage Wireless

Hi. Hearing problems on one of my ears, so i need to adjust the balance on my headset. I don't have this option in properties. http://i.imgur.com/WjnG3Sm.png
Also, this option is not in the software provided by Creative.
Does anyone have a solution for this, or is it only me who is having this problem?
Thanks for any help

Originally Posted by k_flaathe
Hi. Hearing problems on one of my ears, so i need to adjust the balance on my headset. I don't have this option in properties. http://i.imgur.com/WjnG3Sm.png
Also, this option is not in the software provided by Creative.
Does anyone have a solution for this, or is it only me who is having this problem?
Thanks for any help
Hi k_flaathe,
You may want to go to the window control panel, select sound properties of your sound card to adjust the balance.
If you still encounter issue with the headset, , you may want to relay your concern to Tech Support (link HERE).
Do make sure to explain the faulty behavior of your concerns and action taken as much as possible
Cheers !

Similar Messages

Tactic 3D rage wireless volume change

I just bought a tactic 3D rage wireless headset, charged it up, installed the control panel and the firmware from the creative website, and it's working well. However every time I adjust the volume on the headset it bleeps, which is very annoying. How do I disable this?

Hello Zenna,
Welcome to the forum!
There is no way to disable the beep sound. When adjusting the volume with the rotary dial, you will get an audible beep tone as an indicator.

Tactic 3D Rage Wireless V2 connecting issues

"There is no supported audio device available" it says.
I've already done the initial 8 hours of charging and I've used them for 2 days of slight gaming before they ran out of power. Now that I was going to charge them via USB ports (Tried both 2.0 and 3.0 -USB ports) it just didn't respond to anything. No red blinking light, no nothing. And as I mentioned, it only says "There is no supported audio device available" which really pisses me off. I've reinstalled the one and only driver for my headset/operating system 3 times, which also pisses me off really good. So basicly, it worked the first time i charged it, not the second time. It's a brand new headset, got it last wednesday, which pisses me off the most.
Help out this pissed of guy would you?
Kind kind kind regards Alfons ( )

Originally Posted by Afhene
The headset is now detected, strangely since i haven't touched the wireless transmitter at any point. Still, it just doesn't charge. I remind you once again. I charged it once.. the initial 8 hours was painless. I do have a clue for you though. When I restart my computer with USB-charger being put, it says " keyboard: 2, mouse: 2, hubs 2..... shutting down in 15 seconds" and it shuts down as promised. I remove the USB-charger from the USB-port and it does the regular start up. I've tried every single USB-port (I've got 10 of them) and I am still pretty pissed of to be honest. I'll keep saying that until it gets solved, take no offence Creative Employees (unless you've developed this ga***ge).
EDIT: Not sure if it's entirely connected though. Playback Devices sounds setting says "No jack information available" when I look closer into the headset's properties in there.
Somewhat kind regards Me ( )
Hi Afhene,
There is no jack information available for the Tactic3D Rage Wireless. Please avoid charging the headset via a powered USB hub. Connect the headset direct to the computer's powered USB port.
Since your headset is now detected, you can launch the SB Tactic3D Control Panel and look for the battery level indicator of the headset after it has been paired to the USB wireless transmitter.
battery_indicator.jpg
I suspect that your headset is already fully charged when you did the initial battery charging of 8 hours. Hence, there is no response on the Power LED when you charge the headset for the 2nd time. During the battery charging, the Power LED will blink and stops blinking when it is fully charged.
Power LED (blinking) - charging
Power LED (off) - fully charged; power off state
Power LED (solid white) - fully charged, power on state
If you like to learn more about charging Tactic3D Rage Wireless, you may refer to this article:
http://support.creative.com/kb/ShowA...spx?sid=111092
You may opt for firmware update of the USB wireless transmitter & headset and observe situation can be improved. Please follow the instructions carefully.
firmware_update.jpg
Cheers,
JL-CL

Tactic 3d Rage Wireless Possible USB Transmitter Problem

Hi guys,
It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
Many thanks in advance.

Originally Posted by Xotli
Hi guys,
It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
Many thanks in advance.
Hi Xotli,
Do you encounter any error(s) during the firmware update of the headset and the USB transmitter?
Do not connect it to the USB hub. At any one time, the headset and USB transmitter cannot connect together during firmware update; only separate update is allowed.
Here's the instructions given for updating USB transmitter via Windows:
- Download the file onto your local hard disk.
- Ensure that your Sound Blaster Tactic3D Rage Wireless Transmitter is connected to your computer.
- Ensure that the Sound Blaster Tactic3D Rage Wireless Headset is removed from your computer.
- Un-compress the downloaded file to a folder in your local hard disk.
- Double-click <SBTR_PCFW_US_TX_1_59_140721.exe> from the folder which stores the uncompressed files.
- Follow the instructions on the screen.
- After the installation of the firmware is completed, unplug and plug in your transmitter and start pairing with the Sound Blaster Tactic3D Rage Wireless headset again.
Cheers,
JL-CL

My tactic 3d rage wireless wont turn off

So i today got this headset and it was working fine for a while, but after i installed the Sound blaster Tactic(3D) Control panel it suddenly stopped working and now i cant even turn power off from headset.
Windows shows that i've connected to headset and i should hear sounds. I also tried to pair with receiver, but nothing happened.

Same here. I think it's their server(s) problems

Tactic 3D Rage Wireless transmitter soft bricked

Hi guys,
When i was flashing TX firmware, transmitter unplugged then firmware installation was interrupted. Now wifi transmitter doesn't work.
Followed instructions;
Turned off headset
Ran transmitter firmware (SBTR_PCFW_US_TX_1_58_121101)
Then firmware installation was interrupted
Now the light on the wireless transmitter was no longer on
I think wifi transmitter bricked. How can i fix this problem Can anybody help me ?
btw, sorry for my little English.
Thanks in advance..

Originally Posted by bluxe
Yes I tried to install firmware several times but in no way does not install.
I tried plug-in the transmitter directly to my computer as you say. (already I don't have "usb hub")
always i got "cannot detect the device" error.
My problem isn't a hardware problem, completely software problem as I wrote in my first message
Bluxe, If your transmitter is dead and not detected, there is no way to run the firmware update. I suggest you contact technical support here for RMA.

Tactic 3d rage wont turn on

Hey i have a Sound blaster tactic 3d rage wireless and i tried to update the drivers the other day, this resulted in the headset being in a "on mode" which means i couldn't turn it off or do anything with it so i let the battery die and started charging it again when i put the charger in there is a faint redness on the mic button so i knew it was getting power but the head set still wont turn on so i left it for a few hours and i still wont turn on.
Anyone know anything that could help me?
Any help is appreciated,
Cheers.

Originally Posted by Orkneyspanda
Hey i have a Sound blaster tactic 3d rage wireless and i tried to update the drivers the other day, this resulted in the headset being in a "on mode" which means i couldn't turn it off or do anything with it so i let the battery die and started charging it again when i put the charger in there is a faint redness on the mic button so i knew it was getting power but the head set still wont turn on so i left it for a few hours and i still wont turn on.
Anyone know anything that could help me?
Any help is appreciated,
Cheers.
Hi Orkneyspanda,
Welcome to the forums!
Is your case similar to this thread?
- 3D rage headset not recharging with pulsing blue light
Cheers!

Adjusting Audio Volume Levels

Often, one has Audio that is too loud, or too soft. Sometimes, they have added a music Track, that needs to drop down to clearly hear the dialog from another Clip. While there are Audio-editing programs, like Audition, SoundBooth, and even the free Audacity, PrE, or PrPro can handle such adjustment just fine. These adjustments can be made for the entire Clip, or can be Keyframed over time.
First method, and not one that I recommend, is to adjust the Audio Gain of the Audio Clip. This is done by either Rt-clicking on a separate Audio Clip, or by first Alt-clicking, and then Rt-clicking on a Muxed Audio Clip (Multiplexed with both Video and Audio in one file). Then, one would choose Audio Gain, and adjust that. This method will also allow one to then adjust the Volume by a greater amount, and has the bonus of increasing the Waveform Dislay vertically.
The next method is to look at the Audio Clip (or the Audio portion of a Muxed Clip), and click-drag on the yellow-orange “rubberband” for Volume, and move it up, or down. This can be Keyframed, but the next method is much better and more precise, in my estimation.
My first choice is to adjust the fixed Effect>Volume. This is done from the Effects Control Panel, and it is very easy to Keyframe these adjustments over time. This is much more accurate, and actually easier, than click-dragging the rubberbands in the Clip itself. Accessing the Effects Control Panel is slightly different, from PrE to PrPro. In PrE, one would Select the Audio Clip, then go to the Effects Tab, and choose Edit Effects, locating the Volume Effects and twirling it open to view the slider. In PrPro, if one does not already have the Effects Control Panel in a Pane in the GUI, it would be accessed from Window>Effects Control Panel. With the Audio Clip Selected, one would locate the fixed Volume Effect, twirl that open, and make the same adjustments, including Keyframes, if necessary. These will be Clip Keyframes, and will follow that Clip, where ever you move it. This is a difference from the next method.
My other choice would be to use the Audio Mixer (Window>Audio Mixer, if not open), and to automate the Volume settings. This is accomplished by playing the Timeline and adjusting the sliders for Volume for each Track. In PrPro, one would first set the Send to Write, or Touch, to make those adjustments, then switch back to Read, when done. There are no adjustable Sends in PrE, so one is always in Read, until adjustments are made, and then it’s set to Write, but you will not see this change. After you are done, you can playback the Timeline, and watch the slider(s) automatically move. These will be Track Keyframes, and will remain on the Track, regardless of what Clips you add/remove from that area of the Track. Unlike the Clip Keyframes, these will NOT follow the Clip.
One can toggle the Keyframe of an Audio Track between Clip, or Track. Also, the default frequency of Audio Track Keyframes in PrE & PrPro is a bit high, in my opinion. I drop these down a bit in Edit>Preferences.
For the Keyframing, one can alter the Velocity of the Keyframes to Bezier from Linear, and the adjustments will be a bit smoother. Besides the Bezier, one can use Ease-Out and Ease-In, which are Bezier, but basically in a Preset. In PrPro, one has several different Bezier options. In PrE, one is a bit more limited.
For setting the Volume, I recommend that one only glance at the Levels Meters (unless they are peaking in the red), and instead use a pair of high-quality headphones (noise canceling models are worth the money), or fully calibrated studio monitors. Let your ears make the decisions for you, as the dB settings should only be a starting point.
In PrPro, one can also Rt-click on the Audio Clip, and choose Edit in Audition (if you have it installed), or Edit n Soundbooth (if you have one of the suites).
Here is a look at Audio Keyframes in PrPro 2.0. Things are similar in PrPro later versions, and also in PrE, with the above noted differences:

Here are some AdobeTV tutorial links for Premiere Elements Audio:
http://tv.adobe.com/watch/learn-premiere-elements-11/adding-and-customizing-an-audio-effec t/
http://tv.adobe.com/watch/adobe-digital-school-collection/audio-mixing/
http://tv.adobe.com/watch/learn-premiere-elements-10/get-professionalquality-sound-through out-your-movie-/
http://tv.adobe.com/watch/premiere-elements-9-how-tos/enjoy-a-perfect-balance-of-audio/
Hunt

Adjusting Balance in iTunes

I have a slight hearing loss in my left ear. Is there a way to raise the volume in the left channel to compensate? Everything sounds like it is to the right.
And can this "off balance" be transfered to an iPod Classic?
Chim

chims wrote:
Is there a way to raise the volume in the left channel to compensate?
No. iTunes is not a professional application and does not include panning capabilities. What you can do is adjust balance in the Sound control panel in System Preferences.

Weird ticking sound when adjusting the volume...

Hi all
When adjusting the volume using the F3 F4, my new ibook 12" g4 makes a weird ticking sound before it catches up an adjusts the volume with the normal "blop" sound. Is this normal? Batteri is on "normal."
Thanks
Erlend

I have this same problem with my new 1.33Ghz iBook G4. I've had the logic board replaced twice and the top assembly with the speakers replaced twice also. It still makes the ticking noise and it's quite specific to reproduce so none of the Apple tech have spent the time to reproduce it. I think this problem is more wide spread than Apple realizes.
Here are the factors that HAVE to exist for this problem to be reproduced:
1. The computer must be have the AC adapter unplugged and running off of the battery.
2. Un-click "Play feedback when volume is changed" in System Preferences under "Sound" (While this is not exclusive to having the "ticking audio" problem occur, it is easier to notice with this box unchecked)
3. 10.4.2 or 10.4.3 (even happens on a fresh install)
4. Push the F4 and F5 keys to change the volume for at least 10-20 seconds and the "ticking sound" will occur. (the lagging after the tick is most annoying.)
Launching iTunes and playing audio will temporarily make this problem subside. Once this problem occurs with "Play feedback when volume is changed" unchecked, it will continue until audio is played or the sound preference panel is accessed. Often the sound balance will be 100% to the left after this problem has started occuring. (Checking the Sound preference panel shows this)
Has anyone had this problem fixed permanently? Apple seems to be unaware of this problem. 10.4.4 could fix it. Unfortunately we are not even sure if this is a hardware problem or a software issue. I will post with details of what happens when I bring my machine in to the Apple store for the 4th or 5th time.
Power Mac G5 1.8Ghz DP, 1.25GB RAM. G4 iBook 1.33Ghz Mac OS X (10.4.2)

Dv6 1007TX top components (volume, CD track controls & Wireless) are non responsive

The top components on my dv6 1007TX recently stopped working. So I am unable to connect to a wirelss network or adjust the volume via the top componenet, only via the volume control software.
I have tried a system restore and this has not worked. I have reinstalled the wireless drivier, again has not made any difference. I am also getting a error "CNDNDIg has stopped working", I don't know if this is related.
Any idea's on how to get the top componenets working again and what is the CDCNDIg error about?
This question was solved.
View Solution.

Hi,
This can sometimes be caused by a build-up of static. Shutdown the notebook, remove the AC Adapter and then remove the battery. Now hold down the power button for a good 30 seconds. Re-insert the battery, plug in the AC Adapter and start the notebook to see if this has helped the issue.
The file you mention belongs to Canon Digital Software, so you may need to uninstall this software, restart the notebook and then reinstall it ( or if there is an updated version of the software, install this ).
Best wishes,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I have a ringtone that works great on my computer but the volume is very soft on the phone. I have adjusted the volume on the phone but the ringtone volume is still too low. Is there any way to adjust the volume of a ringtone?

I have managed to sync a ringtone to my ne i phone 5C but the volume is way too soft.
The sound is great on my computer but hard to hear at all on the phone. I have tried turning up the volume button on the phone but it doesn' do anything for the ringtone. Any ideas on how to solve this problem. The ringtone is "calypso blackberry" and I am not able to locate it in the Apple store ringtones. This should be so simple and it is making me nuts.
Help anyone please.
Bob

So you use an RCA cable going into what before it hits the MBP?
EDIT: Also in System Preferences > Sound > Input > you can select the input & adjust the volume accordingly as long as it's plugged in.

I have a mid-2009 MBP and I've been using my BOSE Companion 20 with it for about half a year now. It was fine until recently, when i want to adjust the volume using the pod on the BOSE Companion 20, it will cause like a surge in volume, spiking it up

I have a mid-2009 MBP and I've been using my BOSE Companion 20 with it for about half a year now. It was fine until recently, when i want to adjust the volume using the pod on the BOSE Companion 20, it will cause like a surge in volume, spiking it up and down. It will not stablise itself! It's very fustrating. Anybody with the same issue?

I have the BOSE Companion 5 speakers and have had the same problem. I've searched everywhere and gotten nowhere. My speakers are way past their warranty, so calling Bose would probably get me no where either. Only thing I can think of is that the speakers overheat which causes the spikes in the volume. I've tried unplugging them for a few minutes and then plug them back on. The problem does go away, but after about 5 minutes, same problem.

Since I upgraded to the new iOS 7 operating system for my iphone, I can no longer adjust the volume on my alarm. No matter what setting the volume of my phone is my alarm is always full blast. Since I hate being startled awake, what can I do?

Since I upgraded to the new iOS 7 operating system for my iphone, I can no longer adjust the volume on my alarm. No matter what setting the volume of my phone is my alarm is always full blast. Since I hate being startled awake, what can I do?

Go to your home screen, and then press the volume down or up button. It should say Ringer instead of volume. If it doesn't do that, try going into the clock app and try it there.

How do I get itunes to stop adjusting the volume

Hi
I am running iTunes 11.0.2.25 and am really annoyed at how iTunes keeps adjusting the volume on me during playback. I am not talking about the 'sound check' or 'sound enhancer' or any other option that I can see in iTunes. They are all set to 'off'. What I am talking about is while I play a song and turn up the volume, iTunes adjusts it down automatically. I can keep doing this until the volume level is at 100% and the volume barely increases - or increases or a moment and then quietens down again. If I move the volume control to say 25%, the volume becomes almost inaudible, but then iTunes gradually increases the volume automatically to a seemingly random level.
How do I get iTunes to leave the friggin volume alone? Or is this something that can't be controlled?
I have looked at adjusting the 'Volume Adjustment' in the 'Get Info' area of individual songs and the setting there makes no difference whatsoever. I am ready to give up entirely on this piece of flawed software if there is no answer to this problem.
Again, I have diabled the 'sound check' option in 'Preferences', so it is not that.
Does anyone know how to get iTunes to play the song as it was recorded digitally without changing it?
My gratitude in advance for a resolution.
389P

Yes, you'll have to individually add each new song that you've downloaded.
When you add them to iTunes--you're just adding the file path to the location on your computer. When you move the file location, iTunes won't know where to look for it and will give you the infamous "!" symbol. Then you'll have to browse to the new location and tell iTunes where to find it.
How many new songs do you add at a time? If it's not many, it's probably easiest to just add them one file at a time.
To find the new songs, the file names should be good clues--they are fairly complete song titles on my computer.
And, you might want to do this each time you download a new song so you don't forget to add them!

Adjust balance volume Tactic 3d Rage Wireless

Similar Messages

Maybe you are looking for