TE with MPLA exp bit set

Hello
I have a multilink bundle which will be the path used for my primary tunnel. I need to set mpls exp bit for qos (bandwidth reservation for specific traffic class)
Now iam applying my service policy applied on the multilink interface.
If enable my tunnel with explicit path configured as the ips of Multilink interfaces where should my service policy go either on the tunnel interface or Multilink interface.
Futher when my primary tunnel fails i have another path configured as next path option either explicit or dynamic. Can i have the same qos on the other path also if enable the service policy on the tunnel interface.
REgards
Parthiban

The following documents have more information on marking packets in QoS.
http://www.cisco.com/warp/public/105/dscpvalues.html
http://www.cisco.com/en/US/products/sw/iosswrel/ps5014/products_feature_guide_chapter09186a00800ca4f0.html

Similar Messages

External route with Down Bit set by CE router

I have a question regarding the Down Bit. All the documentation I see concentrates on the redistribution of the MP-BGP into OSPF but I want to know more about the OSPF redistribution into MP-BGP. I think the rule is different for Type3 and Type5 LSAs.
Lets say the CE redistributes a RIP route into OSPF, creating an LSA Type 5 route sent to the PE router - with the Down Bit set.
Will this PE router redistribute this route into MP-BGP?
I know that LSA Type 3 summary routes will not be redistributed into MP-BGP if the Down Bit is set but I am wondering about external OSPF routes with the Down Bit set????
I am assuming that redistribution of RIP into OSPF at the CE does infact set this Down Bit before passing on to the PE router?

How can step 2 in the sequence description say that PE2-AS1 receives an OSPF route with the Down Bit already set? This comes from the CE.
I find this all very confusing when I check out these sequences - I thought only the PE router assigns Down Bit to LSA Type 3 routes?
All the other references I see show how PE1-AS1 would normally set the Down Bit as it is redistributed back into OSPF?
Thanks for your help - I feel I am getting closer. It is just this second step that is throwing me!
Cheers
Walter

Wred based on MPLS exp bits on 12000

I want to use WRED with MQC on 12000 but there is no mpls/exp-bits statment on the "random-detect" command.
I found this note at cisco documentation:
Note: The legacy CLI also uses the precedence syntax for Multiprotocol Label Switching (MPLS) traffic. The router treats the MPLS bits as though they are IP Type of Service (ToS) bits and puts the appropriate packets into the correct queues. This is not at all true for MQC.
so, is there a way to use WRED with MPLS EXP-bits on MQC?

Hi,
As fas as I know the solution is as follows:
1. Use MQC on the inbound interface of your P/PE LSR to match your desired traffic and set discard-class
2. Use MQC on the outbound interface of your P/PE
LSR to set desired WRED policy based on discard-class you marked in previous step. You also need to mark WRED as "discard-class-based"
Here is an example:
Inbound:
class-map class1
match XXXXX
class-map class2
match YYYYY
policy-map in-policy
class class1
set discard-class 0
class class2
set discard-class 1
Outbound:
policy-map out-policy
class class-default
random-detect discard-class-based
random-detect discard-class 0 10 20 5
random-detect discard-class 1 20 30 5
Hope that helped.
David

MPLS , DF bit set

Hi everybody
According to my book, if an LSR can not fragment the labelled packet because of DF bit, following will occur:
Only if the IP header has the Don’t Fragment (DF) bit set does the LSR not fragment the IP packet, but it drops the packet and returns an ICMP error message “Fragmentation needed and do not fragment bit set” (ICMP type 3, code 4) to the originator of the IP packet. As with the ICMP message “time exceeded” (type 11, code 0), which is sent when the TTL expires of a labeled packet, the “Fragmentation needed and do not fragment bit set” ICMP message is sent, using a label stack that is the outgoing label stack for the packet that caused the ICMP message to be created. This means that the ICMP message travels further down the LSP until it reaches the egress LSR of that LSP. Then it is returned to the originator of the packet with the DF bit set.
However, when i put this claim to test, i do not see that behavior.
R5---R1 f0/1-----R2----R3---R4
Above R1 f0/1 mpls mtu 1400
On R5, i generated a ping of 1500 , DF bit set. R1 should send ICMP error towards R4 which then send it to R5.
R5#debug ip icmp
ICMP packet debugging is on
R5#ping
Protocol [ip]:
Target IP address: 4.4.4.4
Repeat count [5]:
Datagram size [100]: 1500
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface:
Type of service [0]:
Set DF bit in IP header? [no]: y
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 1500-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds:
Packet sent with the DF bit set
Success rate is 0 percent (0/5)
I do not see such ICMP errors message being received. Wireshark capture between R1--R2, does not show that any ICMP error message from R1 either.
I suspect the packets with DF bit are silently discarded by LSR ( R1). If this is true, then my book is pretty wrong.
thanks

Thanks Nagendra
R4#show version
Cisco IOS Software, 2600 Software (C2691-ADVIPSERVICESK9-M), Version 12.4(15)T6, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Mon 07-Jul-08 04:30 by prod_rel_team
ROM: ROMMON Emulation Microcode
ROM: 2600 Software (C2691-ADVIPSERVICESK9-M), Version 12.4(15)T6, RELEASE SOFTWARE (fc2)
R4 uptime is 46 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

EXP bits with Label Stacking

In 12.0S, with ATOM or L3VPNs and label stacking which label's EXP bits are set using 'set mpls experimental' or using rate-limits? All labels in the stack?
I see the newer 'set mpls experimental' commands in 12.2 and 12.3 that can control which label's EXP bits are set; topmost, etc. However, I need 12.0S for any-to-any ATOM.
Thanks.

This command will set the EXP bits on all labels at label imposition. The IP Precedence bits will not be affected.
Hope this helps,

OSPF LSA with DC bit set

Hello,
If an LSA is received by an OSPF router which is not Demand Circuit capable, will that LSA be installed in link state database?
Thanks

How can step 2 in the sequence description say that PE2-AS1 receives an OSPF route with the Down Bit already set? This comes from the CE.
I find this all very confusing when I check out these sequences - I thought only the PE router assigns Down Bit to LSA Type 3 routes?
All the other references I see show how PE1-AS1 would normally set the Down Bit as it is redistributed back into OSPF?
Thanks for your help - I feel I am getting closer. It is just this second step that is throwing me!
Cheers
Walter

MPLS EXP-BIT

class-map X
match ip dscp af41
policy whatever
class-map X
police 312000 24000 48000 conform-action set-mpls-exp-transmit 6 exceed-action set-mpls-exp-transmit 2
Question:
does the "set-mpls-exp-transmit" remark or encapsulate this AF41 to MPLS-EXP 6? My objective here is maintain "transparency" of the DSCP marking that is coming, meaning I would like this AF41 marking to remain untouched across my mpls backbone. My research tells me to do that I need to use set-mpls-exp with the "topmost" keyword which will give me DSCP Tunneling.
Can you guys clarify that for me? Am i reading this thing right?

Hi,
setting the MPLS exp bits does leave the IP DSCP bits untouched. The default behaviour by the way is to copy precedence to MPLS exp bits anyhow. With the policer you can remark in your MPLS network according to the SLA negotiated.
On some platforms you might have to use for example
policy-map CustomerIn
class business
police cir percent 25
conform-action set-mpls-exp-imposition-transmit 4
exceed-action set-mpls-exp-imposition-transmit 0
violate-action set-mpls-exp-imposition-transmit 0
Be aware that on the output from PE to CE you will have IP packets again. The exp bits are not copied to IP precedence by default. So either you use DSCP in the output policy on the PE with the customer values.
The other option is to map exp bits to a qos group and use this for the output policy. The advantage of the latter approach is that you do have consistent qos policies on a PE not refering to (different) customer markings.
Hope this helps
Martin

PROBLEM with 24/96 bit-rate USB DAC that worked fine until I plugged in two

I'm using a late 2008 15" Macbook Pro that I bought Jan 2009 right before the SD card models came out. Mac OSX 10.6.4 and iTunes 9.2 are installed. I have a Nuforce Icon HDP and a CEntrance DACport 24/96 bit-rate USB DAC (external sound cards) that still work great right now. Note - 16 bit/44 Khz is CD quality, and these 24/96 files are hi-resolution downloads that are closer to SACD or DVD audio.
I have been evaluating a new third 24/96 USB DAC plugged directly into the Macbook USB port (no hub) which has been working fine for over 2 weeks with 24/96 bit-rate lossless music files in iTunes. Audio Midi Setup is set for 24/96 to match the music file's resolution. After making suggestions to the manufacturer they made some improvements and sent me a new version to listen for the differences.
I listened to the new one for a day and it worked fine, but when I plugged in the original test sample into the second USB port at the same time as the new one in order to compare them, the sound became garbled and noisy. This never happened when either one was plugged in by itself. Note, if I make changes to the DAC's bit-rate in Audio Midi Setup I usually close iTunes first and then re-open it when I am done.
Upon hearing this new problem I unplugged both of the new USB DACs and plugged just one of them back in, but now it causes iTunes music playback to pause when one is plugged in and set for 24/96 in audio midi setup. Prior to plugging in both at the same time, either one worked just fine by itself. There is no reason when unplugging one or the other that they shouldn't start working again. But now I can't play any 24/96 music through either one anymore. In quicktime player the songs don't pause like with iTunes, but there is no sound coming through even with just one DAC plugged in at a time. Then I discovered that if I go into Audio Midi Setup application and lower the bit rate to 24/48 then iTunes will resume playing again and I can hear the music fine with iTunes or Quicktime player.
Basically, my Macbook Pro has now lost the ability to play 24/96 bit rate with either of these new USB DACs, when they both worked fine before I plugged them in at the same time. More confusing is that they use the same USB receiver chip as in one of the DACs that I mentioned above in the first paragraph, and both the HDP and DACport still work fine at 24/96 bit-rate. It's only these two new USB DAC that require me to lower the bit rate in Audio Midi Setup to 24/48 in order to listen through them, and this wasn't a problem as recently as yesterday!
The computer is acting like some setting needs to be wiped out - it's DEFINITELY NOT the USB DAC's that are faulty because they still both work fine at 24/96 on my wife's iMac (I'm afraid to try plugging in both at the same time to the iMac in case I screw that Mac up too).
I have reset the PRAM a few times, and this doesn't fix the problem. I thought maybe the com.apple.audiomidisetup.plist file could be corrupted and deleted it, but that didn't help. I don't know what to try next to get the Macbook to start fresh when trying to use these devices, short of having to re-install OSX.
Please, does anyone have a suggestion of how I can make the Macbook forget it ever saw these two USB DACs, and let me start fresh so they start working normally again? I do dozens of reviews for Head-fi.org and I can't afford to have my Macbook Pro compromised like this, which could prevent me from doing some reviews or evaluating new products.

UPDATE:
As noted in the first post, both of these newer USB DAC work fine at 24/96 on my wife's iMac, so it's clear that they didn't both become defective when I connected them to the Macbook Pro at the same time.
Resetting the Macbook Pro PRAM didn't help, so I removed the hard shell laptop case to get to the battery and remove it, then reset the SMC. After that I could use the original DAC at 24/96 again, but only IF it was plugged into the rear USB port. If I plugged it into the front USB port then the sound was garbled and filled with noise. This was a vast improvement over no sound at all.
Then I switched to the replacement/updated DAC, but I got no sound at all from either USB port at any bit-rate. And returning to the original DAC again now results in no sound again.
Sigh... I will reset the PRAM and SMC again, and see how far I can get with this. I'd still love some help. Thanks!

New files and folders on a Linux client mounting a Windows 2012 Server for NFS share do not inherit Owner and Group when SetGID bit set

Problem statement
When I mount a Windows NFS service file share using UUUA and set the Owner and Group, and set the SetGID bit on the parent folder in a hierarchy. New Files and folders inside and underneath the parent folder do not inherit the Owner and Group permissions
of the parent.
I am given to understand from this Microsoft KnowledgeBase article (http://support.microsoft.com/kb/951716/en-gb) the problem is due to the Windows implmentation of NFS Services not supporting the Solaris SystemV or BSD grpid "Semantics"
However the article says the same functionality can acheived by using ACE Inheritance in conjunction with changing the Registry setting for "KeepInheritance" to enable Inheritance propagation of the Permissions by the Windows NFS Services.
1. The Precise location of the "KeepInheritance" DWORD key appears to have "moved" in Windows Server 2012 from a Services path to a Software path, is this documented somewhere? And after enabling it, (or creating it in the previous
location) the feature seems non-functional. Is there a method to file a Bug with Microsoft for this Feature?
2. All of the references on demonstrating how to set an ACE to achieve the same result "currently" either lead to broken links on Microsoft technical websites, or are not explicit they are vague or circumreferential. There are no plain Examples.
Can an Example be provided?
3. Is UUUA compatible with the method of setting ACE to acheive this result, or must the Linux client mount be "Mapped" using an Authentication source. And could that be with the new Flat File passwd and group files in c:\windows\system32\drivers\etc
and is there an Example available.
Scenario:
Windows Server 2012 Standard
File Server (Role)
+- Server for NFS (Role) << -- installed
General --
Folder path: F:\Shares\raid-6-array
Remote path: fs4:/raid-6-array
Protocol: NFS
Authentication --
No server authentication
+- No server authentication (AUTH_SYS)
++- Enable unmapped user access
+++- Allow unmapped user access by UID/GID
Share Permissions --
Name: linux_nfs_client.host.edu
Permissions: Read/Write
Root Access: Allowed
Encoding: ANSI
NTFS Permissions --
Type: Allow
Principal: BUILTIN\Administrators
Access: Full Control
Applies to: This folder only
Type: Allow
Principal: NT AUTHORITY\SYSTEM
Access: Full Control
Applies to: This folder only
-- John Willis, Facebook: John-Willis, Skype: john.willis7416

I'm making some "major" progress on this problem.
1. Apparently the "semantics" issue to honor SGID or grpid in NFS on the server side or the client side has been debated for some time. It also existed as of 2009 between Solaris nfs server and Linux nfs clients. The Linux community defaulted to declaring
it a "Server" side issue to avoid "Race" conditions between simultaneous access users and the local file system daemons. The client would have to "check" for the SGID and reformulate its CREATE request to specify the Secondary group it would have to "notice"
by which time it could have changed on the server. SUN declined to fix it.. even though there were reports it did not behave the same between nfs3 vs nfs4 daemons.. which might be because nfs4 servers have local ACL or ACE entries to process.. and a new local/nfs
"inheritance" scheme to worry about honoring.. that could place it in conflict with remote access.. and push the responsibility "outwards" to the nfs client.. introducing a race condition, necessitating "locking" semantics.
This article covers that discovery and no resolution - http://thr3ads.net/zfs-discuss/2009/10/569334-CR6894234-improved-sgid-directory-compatibility-with-non-Solaris-NFS-clients
2. A much Older Microsoft Knowledge Based article had explicit examples of using Windows ACEs and Inheritance to "mitigate" the issue.. basically the nfs client "cannot" update an ACE to make it "Inheritable" [-but-] a Windows side Admin or Windows User
[-can-] update or promote an existing ACE to "Inheritable"
Here are the pertinent statements -
"In Windows Services for UNIX 2.3, you can use the KeepInheritance registry value to set inheritable ACEs and to make sure that these ACEs apply to newly created files and folders on NFS shares."
"Note About the Permissions That Are Set by NFS Clients
The KeepInheritance option only applies ACEs that have inheritance enabled. Any permissions that are set by an NFS client will
only apply to that file or folder, so the resulting ACEs created by an NFS client will
not have inheritance set."
"So
If you want a folder's permissions to be inherited to new subfolders and files, you must set its permissions from the Windows NFS server because the permissions that are set by NFS clients only apply to the folder itself."
http://support.microsoft.com/default.aspx?scid=kb;en-us;321049
3. I have set up a Windows 2008r2 NFS server and mounted it with a Redhat Enteprise Linux 5 release 10 x86_64 server [Oct 31, 2013] and so far this does appear to be the case.
4. In order to mount and then switch user to a non-root user to create subdirectories and files, I had to mount the NFS share (after enabling Anonymous AUTH_SYS mapping) this is not a good thing, but it was because I have been using UUUA - Unmapped Unix
User Access Mapping, which makes no attempt to "map" a Unix UID/GID set by the NFS client to a Windows User account.
To verify the Inheritance of additional ACEs on new subdirectories and files created by a non-root Unix user, on the Windows NFS server I used the right click properties, security tab context menu, then Advanced to list all the ACEs and looked at the far
Column reflecting if it applied to [This folder only, or This folder and Subdirectories, or This folder and subdirectories and files]
5. All new Subdirectories and files createdby the non-root user had a [Non-Inheritance] ACE created for them.
6. I turned a [Non-Inheritance] ACE into an [Inheritance] ACE by selecting it then clicking [Edit] and using the Drop down to select [This folder, subdirs and files] then I went back to the NFS client and created more subdirs and files. Then back to the
Windows NFS server and checked the new subdirs and folders and they did Inherit the Windows NFS server ACE! - However the UID/GID of the subdirs and folders remained unchanged, they did not reflect the new "Effective" ownership or group membership.
7. I "believe" because I was using UUUA and working "behind" the UID/GID presentation layer for the NFS client, it did not update that presentation layer. It might do that "if" I were using a Mapping mechanism and mapped UID/GID to Windows User SIDs and
Group SIDs. Windows 2008r2 no longer has a "simple" Mapping server, it does not accept flat text files and requires a Schema extension to Active Directory just to MAP a windows account to a UID/GID.. a lot of overhead. Windows Server 2012 accepts flat text
files like /etc/passwd and /etc/group to perform this function and is next on my list of things to see if that will update the UID/GID based on the Windows ACE entries. Since the Local ACE take precedence "over" Inherited ACEs there could be a problem. The
Inheritance appears to be intended [only] to retain Administrative rights over user created subdirs and files by adding an additional ACE at the time of creation.
8. I did verify from the NFS client side in Linux that "Even though" the UID/GID seem to reflect the local non-root user should not have the ability to traverse or create new files, the "phantom" NFS Server ACEs are in place and do permit the function..
reconciling the "view" with "reality" appears problematic, unless the User Mapping will update "effective" rights and ownership in the "view"
-- John Willis, Facebook: John-Willis, Skype: john.willis7416

Running in 64 bit mode with the 32 bit Oracle client installed

I have seen many postings on this issue but none of the suggested solutions have helped me.
I am running visual studio 2010 professional with SP1 on windows 7 64 bit machine. When I try to run a web service locally and call it with SoapUI, I get the following error message during OracleConnection.Open().
Attempt to load Oracle client libraries threw BadImageFormatException. This problem will occur when running in 64 bit mode with the 32 bit Oracle client components installed.
I have tried setting up the build configuration and the project settings to target 32 bit but that has not helped. I have also tried removing the reference to System.Data.OracleClient that shows being under Program Files (x86) and add a new reference to the dll under GAC_64. That too did not work.
I only have the 64 bit client installed on my machine.
Any help will be appreciated.
Thank you

1. Visual Studio any version is 32 bit ONLY irrespective of hardware or OS bits. So to DEVELOP with Oracle Client you MUST install 32 bit Oracle ODAC components. Task manager will show devenv.exe *32 (to confirm 32 bit Visual Studio application).
2. You can run your web application inside IIS/IIS Express in your PC which independently can be either 32bit or 64bit. If it is 64 bit, you MUST also install 64 bit Oracle ODAC components which means you'll have to install both 32bit and 64bit in your 64 bit Win7 running on 64bit hardware.
3. In Visual Studio if you compile with "AnyCPU" as target, the resultant binaries (Web/NonWeb) can be both 32bit or 64bit. So if target PC is "AnyCPU" or "x64", you MUST install Oracle ODAC 64 bit in the target OS if that target OS is 64bit. You don't have to install 32bit ODAC in the target PC.
4. One more catch to above scenario is the target OS could be 64bit simulated OS on a 32bit hardware. In such case you MUST install both 32bit and 64bit ODAC components.
So while you ask your network team to download ODP.NET/ODAC Components make sure you ask them to download both 32bit and 64bit. Total nearly 600MB.
Hope this helps many people out there.

Object variable or With Block variable not set

Hi - We have saved a working input schedule to a new name and modified it to use for another company. There is a report tab to bring down the historical units from BPC, a tab to trend the history, and a tab that references the other two tabs to forecast the units into the future and send the forecasted units back up to BPC. The input schedule that was saved to a new name and modified works fine until we attempt to Send and Refresh the active worksheet on the forecast tab. When we do so, it indicates the number of records that will be sent, but when it attempts to Process the upload to BPC we receive an error message that indicates Object variable or With Block variable not set and no records are sent to BPC.
We have retested the original input template that was copied and the original template still transfers data successfully to BPC. We have also tried starting with a blank input template and copying in the formulas from the working template and we still get the same error message.
We have read several postings on this error and it seems to be a pretty general error, and so far none of the suggestions have worked for us. One suggested checking for special characters, but the only non alpha non-numeric characters used are dashes in the values of one of the dimensions and spaces and underlines in the formulas used to forecast the units, but both of these are present and don't seem to cause any problem in the working input schedule.
We are currently on BPC 7.5 SP6 and using Excel 2010.
Any help would be appreciated.

>Note 1494285 seems to be in reference to BPC for Microsoft and we are using NetWeaver.
Sorry, 1513080 is for NW (there's link to it in bottom of 1494285) :
- Currently only BPC 7.5 NW SP05 and above support Office 2010
- Note: BPC NW 7.5 NW cannot work on office 2010 (64-bits), office 2010 (64-bits) is not supported.
Check your proxy settings (note 1592560: Getting "Error 91 Object variable or with block variable after upgrade to SP06" in the Excel Client.)
Try 1576893: After upgrading to SP06, the EVDRE reports stop working.
PS. Maybe I wrong, but some problems with 2010 Office clients in our system dissapear after patching to SP08.

Object variable or With block variable not set error message

When processing the Rate application I get a "Object variable or With block variable not set error message" What is causing this error and how do I fix it?

Hi Brian,
I'm afraid that in some ways this reply won't be very helpful though it may help you save some time.
The error message you describe is a very generic one thrown by Microsoft .NET (the programming platform that SAP is written with, see the link at the bottom of this message) and not being 'handled' by SAP.
This means from a SAP perspective that any one of many unrelated things may be causing the error and that it gives you virtually no help in tracking the problem down in SAP.
We've plagued by this message quite a bit, my advice is to look for clues at to what may be happening elsewhere, e.g. try:
1. The windows event viewer, if you are in a multi-server environment then check the event log on all machines.
2. The SQL Server event log (this can be found in Management Studio - Management - SQL Server Logs assuming you're using SQL Server 2005)
3. IIS logs, usually these are text files in the following location -
HTTP.SYS Error Log - %windir%\System32\LogFiles\HTTPERR
IIS Website Log - %windir%\System32\LogFiles\W3SVC#
It is dull work trawling through all these places looking for error events with a timestamp similar to the time your error was encountered, but by doing this we've been able to troubleshoot some issues that otherwise would have taken us ages to rectify via trial and error.
Sorry that there is no definitive answer, but if itu2019s of any help there's many more of us out there who this error message causes trouble for.
Regards,
Iain
Microsoft "Object variable or With block variable not set" error message link:
http://support.microsoft.com/kb/316478

Object variable or With block variable not set, Outlook 2010.

I am using Outlook from Office 2010 Professional (32 bit) and have Exchange 2010 from SBS2011 installed on the server.
Outlook cannot sync with the server over the LAN. This started suddenly about 6 hours ago.
I can send from outlook and it is delivered. I can receive into outlook. I can also send and receive on the phone using the Exchange server. However, the sent emails are not showing up in the sent folder of Outlook. The phone can see its own sent emails,
but not those from outlook.
I haver rebooted the PC and the server with the same result. When I open outlook, is get an error dialogue box with a title, "Contact Sync" and a message, "Error: Object variable or With block variable not set."
My contacts and calender are visible. Email sent since early this afternoon are not recorded in Outlook.
Any thoughts?
Thanks

Hi,
Do you mean all emails that are send from phone are not showing up in the sent folder of Outlook? Please check whether these emails are showing in Outlook Online mode or OWA.
Please make sure all emails send from Outlook can be listed in Sent Items folder correctly. If the problematic emails can be viewed in OWA and Outlook Online mode and the issue only happens to Outlook Cached mode, please manually sync the folder by clicking
Send/Receive button to have a try. If it doesn’t work, we can create a new Outlook profile to have a check.
As for the “Contact Sync” error, please try to launch Outlook with safe mode (“Outlook.exe .safe”) to check whether the issue still persists. Some of third-party programs such as QuickBooks Contact Sync or corrupted VBA coding may cause that. If it
is, please refer to the following article to check it:
http://dataservices.intuit.com/support/articles/sln43126
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
sure that you completely understand the risk before retrieving any suggestions from the above link.
Thanks,
Winnie Liang
TechNet Community Support

This problem will occur when running in 64 bit mode with the 32 bit Oracle client components installed.

hi friends ,
My report Fetch from the orcle database , we installed Oracle 10g and 11g - clent 32 -bit on win 2k8 -64 bit machine .while design time runing fine,but ofter depolyement im facing below issue.
In error has occurred during report processing. (rsProcessingAborted)
The execution failed for the shared data set 'abc'. (rsDataSetExecutionError)
Cannot create a connection to data source ' Data source for shared dataset'. (rsErrorOpeningConnection)
Attempt to load Oracle client libraries threw BadImageFormatException. This problem will occur when running in 64 bit mode with the 32 bit Oracle client components installed.
An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
Any help is greatly appreciated, I have tried couple of solutions going through some threads online but no use and place dt tell install 1og r 11g 64-bit

Hi,
Based on the error message, we should confirm whether Oracle client tool has been installed on the Report Server at the beginning. If the Report Server installed is 64-bit, we should also install a 64-bit Oracle client tool on the Report Server. Besides, we
can also try to bypass tnsnames.ora file when connecting to Oracle by specifying all the information in the data source instead of using the TNS alias to connect
to the Oracle database. Please see the sample below:
Data Source=(DESCRIPTION=(CID=GTU_APP)(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST= server01.mydomain.com)(PORT=1521)))(CONNECT_DATA=(SID=OracleDB)(SERVER=DEDICATED)));
Reference:http://blogs.msdn.com/b/dataaccesstechnologies/archive/2010/06/30/ora-12154-tns-could-not-resolve-the-connect-identifier-specified-error-while-creating-a-linked-server-to-oracle.aspx
Hope this helps.
Regards,
Heidi Duan
Heidi Duan
TechNet Community Support

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. Help

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. I have Added a screen Shot of the Brush settings and a demonstration of what the brush produces.
I also notice That when I make a pattern of a single color, when I fill a selection with the pattern I get a rainbow of different colors.
I am running a 64 bit version of Photoshop from the CS6 Masters Collection
I am on a PC with a Intel i7 1366 4 physical cores and 8 threads, 24 Gig of DDR memory, A Crucial 512 Gig SSD and a NVIDIA GTX 570 with 2 Gig of memory.
The document size is 2100 by 1500 Pixels at 300 PPI only two layers

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. I have Added a screen Shot of the Brush settings and a demonstration of what the brush produces.
I also notice That when I make a pattern of a single color, when I fill a selection with the pattern I get a rainbow of different colors.
I am running a 64 bit version of Photoshop from the CS6 Masters Collection
I am on a PC with a Intel i7 1366 4 physical cores and 8 threads, 24 Gig of DDR memory, A Crucial 512 Gig SSD and a NVIDIA GTX 570 with 2 Gig of memory.
The document size is 2100 by 1500 Pixels at 300 PPI only two layers

TE with MPLA exp bit set

Similar Messages

Maybe you are looking for