Test Print

to make sure i have install the printer how do I test print? For wireless printing

Hello Lynda
If you,ve set up the printer send it as an email. I take it youre talking about eprint, right?

Similar Messages

MFP M127fn connected, test printing OK, can't print from applications

Hello Everyone!
I have just set up my M127fn via USB on a Windows 8 system. The set up went fine. I have a small stack of test pages from the HP software, but it won't print anything from any applications like MSOffice. The HP diagnostic software (Print and Scan Doctor 4.6) can communicate with the printer and everything checks out OK.
Any suggestions?
Thanks in advance.

Hello!
I have replied twice to your last posting, but have heard no response. Unless a solution can be presented quickly, I fell I must return the product. LPug and play was introduced with Windows 95 and this HP product has not lived up to that 20 year old technological standard. My previous replies are copied below.
Please respond soon.__________________________________________
Re: MFP M127fn connected, test printing OK, can't print from applications
Options
‎01-31-2015 08:06 AM
Hello again!
I haven't heard a response to my most recent reply. Is there anything you can suggest before I give up and return this HP product to the store? I would like a quick resolution to this. As an update to my previous email (copied below), printing is no longer working through Adobe Reader.
Thanks,
Chris
Re: MFP M127fn connected, test printing OK, can't print from applications
Options
‎01-28-2015 01:08 PM
Hi,
Thanks for getting back to me. I have tried a variety of different programs:
Mozilla Thinderbird (email) - no results
MS Word - no
ms excel - no
Finale (music software) - no
Adobe Reader - yes!
Google Chrome - yes!
NotePad - yes!
perplexing!

Hi All, I setup 2 Mac Minis, 'setup in a no-apple id. Now with Mini1 I installed a shared printer from Windows7 Pc it ask for credentials then I input Adminstrator account and the password ticking the remember in "keychain" I run a test print and its se

Hi All,
I setup 2 Mac Minis, 'setup in a no-apple id. Now with Mini1 I installed a shared printer from Windows7 Pc it ask for credentials then I input Adminstrator account and the password ticking the remember in "keychain"
I run a test print and its seamless. I reboot the Mini1 and run test print again and its good.
Now in Mini2 I did the same installation on shared printer but it is asking for user credential again and again, there is a check mark in "remember in keychain but still gives a notice that "requires authentication" I put the admin creadentials same with Mini1 then it prints.
every time I print on Mini2 its always asking for a user & password before Printing. How can we fix it.
I tried
- lpd printing = "authentication required"
- reset printer settings ang re-install printer = "authentication required"
- replace sharename in windows7, reinstall printer in Mini2 = "authentication required"
This stuff never happened to Mini1.

Hi All,
I setup 2 Mac Minis, 'setup in a no-apple id. Now with Mini1 I installed a shared printer from Windows7 Pc it ask for credentials then I input Adminstrator account and the password ticking the remember in "keychain"
I run a test print and its seamless. I reboot the Mini1 and run test print again and its good.
Now in Mini2 I did the same installation on shared printer but it is asking for user credential again and again, there is a check mark in "remember in keychain but still gives a notice that "requires authentication" I put the admin creadentials same with Mini1 then it prints.
every time I print on Mini2 its always asking for a user & password before Printing. How can we fix it.
I tried
- lpd printing = "authentication required"
- reset printer settings ang re-install printer = "authentication required"
- replace sharename in windows7, reinstall printer in Mini2 = "authentication required"
This stuff never happened to Mini1.

HP C6150 All-In-One Will Not Print Black Text But Does Partial Test Print

Hi. Thanks in advance for any help anyone can proffer.
I've read through the forum and I think there are some similar issues, but none exactly the same as ours.
This HP C6150 does print pictures, but suddenly stopped printing black text.
HOWEVER, the test prints will print in black with the Windows Logo, but will not print any associated text.
Odd. It just suddenly stopped printing.
Variables:
C6150 All in One - No other problems for two years.
Using refilled ink cartridges from outside source. (not my decision)
Ink is full. No other changes made in last three days.
Troubleshooting Steps:
Uninstalled and then re-installed software in entirety.
Put in 'new' (refilled) cartridge for black and magenta.
Tried (not sure if successful) soft reset.
Tried cleaning the print cartridge with 'Q-Tip' and distilled water.
Have not yet spent money on new OEM print cartridges. That is next step unless other suggestions merit.
Possibilities:
It may be the refilled cartridges, but they've worked so well in the past.
The cartridge prior to the recent replacement was working fine and was not yet out of ink.
The print head might be damaged. But this should/would affect all black printing and this is not the case.
Were the driver corrupt, the reinstall should have fixed it ... you'd think.
So, we're looking for some suggestions prior to going out and getting a new printer.
Thanks again, in advance, for constructive non-judgmental suggestions.
MackNC

The likely cause is the black ink is not printing at all. When printing graphics (like the Windows Test Page) black is made from mixing the color ink. I would suggest printing an internal diagnostic test page as shown in this page. Does the black block print? If not then clean the printheads as described here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Printer will not print word documents or documents from internet however does a test print

My printer will not print word documents or documents from the internet. However it does complete a test print. I have uninstalled and reinstalled printer. I have disabled and enbled the firewall and have run the test doctor programme, which has been unable to identify any problems. I have a HP deskjet 3050A all in one J611 series printer.

Sorry that you are having a problem with printing word documents and internet.
Are you connected USB or wireless?
You can try to download an alternative driver and check to see if that works. (Shane_R) has a great post on how to do so.
The deskjet 990c is usually the better one.
http://h30434.www3.hp.com/t5/Printer-All-in-One-Software-Drivers-e-g-Windows-8/How-to-Assign-Alterna...
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

Test print for script form

Hi,
while i am testing the form in SE71 using menu -> utilities-> test print.
it will get the error message "language XX is not in the system"
Please help out for the problem ASAP.
Thanks & Regards,
Prathap kumar K.

Hi,
Check out the language key provided in the Administrative Data Tab. If you want to know the error you can check as follows:
Goto SE71.
Goto Form - Check - Texts
You will get a window, uncheck all the other options and
check Include res.
It will display the error.
Reward if useful...

How to do a test print

I have a 110 series. One or more of the cartridges are running out. A test print would tell me which one. How do I do a test print?

Hello rogerwendy,
Which printers did you have? If it's a Photosmart e-AiO D110 continue with this:
You can see an estimate of the ink levels via the Solution Center - open the Solution Center, click on Settings and then on Printer Toolbox. Click on the tab called Estimated Ink Levels and you should be able to see the ink levels of your cartridges.
You can also print a test page called print quality report, if you follow this link and go to Solution Six in the document you will find instructions for how to print this test page:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02002581&cc=us&lc=en&dlc=en&product=4023246

How to avoid TEST PRINT page

Dear All,
How to aviod the test print page in printing. I am getting SAP cover page(test print page) for every time I am printing. I ma using the following code.
CASE sy-ucomm.
    WHEN 'PRNT'.
      DATA: l_params TYPE pri_params,
            l_valid TYPE c,
            l_arc_params TYPE arc_params.
          l_params-prsap = 'X'.
      CALL FUNCTION 'GET_PRINT_PARAMETERS'
        EXPORTING
          destination            = 'LPIN'
          copies                 = 1
         list_name              = 'TEST'
         list_text              = 'Test NEW-PAGE PRINT ON'
          immediately            = 'X'
          layout                 = 'X_65_132'
          line_count             = 65
          line_size              = 220
          release                = 'X'
          mode                   = 'CURRENT'
          no_dialog              = 'X'
        IMPORTING
          out_parameters         = l_params
          valid                  = l_valid
        EXCEPTIONS
          archive_info_not_found = 1
          invalid_print_params   = 2
          invalid_archive_params = 3
          OTHERS                 = 4.
      NEW-PAGE PRINT ON   PARAMETERS l_params NO DIALOG.
      PERFORM display_data.
      NEW-PAGE PRINT OFF.
ENDCASE.
Thanks,
Ranjan

Hi,
Just check it out. I m printed report directly instead of display.
w_destination = 'LOCL'.
    CALL FUNCTION 'GET_PRINT_PARAMETERS'
      EXPORTING
        destination    = w_destination
        layout         = 'X_58_170'
        no_dialog      = 'X'
      IMPORTING
        out_parameters = params
        valid          = valid.
    IF valid <> space.
ALL DISPLAY PARAMETER RIGHT ON PRINTER
      NEW-PAGE PRINT ON PARAMETERS params NO DIALOG.
    ELSE.
GIVE ERROR PRINTER DESTINATION IS NOT VALID
      MESSAGE s208(00) WITH text-010.
    ENDIF.
ENDIF.
User write stament, That will dirctly go for print.
OFF THE PRINTING AFTER REPORT IS DISPLAY
IF valid <> space.
    NEW-PAGE PRINT OFF.
ENDIF.
it may sortout ur problem.
Regard,
Vinod

My brand new printer LaserJet Pro MPF M127fn won't print after initial test print worked fine

Just installed this printer. USB connection to my PC. Test prints worked fine. Suddenly has stop printing from Word or emails.

On your Mac, open:
System preferences > Network > (whatever your connection) and examine the IPv4 Address.
Wired routers most often use local addresses in the 192.168.xxx.yyy range
Wireless Routers most often use local addresses in the 10.10.xxx.yyy range.
These ranges (along with a few others) are reserved for sets of "private" addresses, that are not visible on the Internet.
The Router will usually be located at kkk.lll.mmm.01
Whatever the range you are using, all the devices with similar addresses can talk freely to each other without any intervention. Any devices with sharply different addresses (such as the entirety of the Internet) must use the Router as their "agent" to communicate.
You want your printers to have addresses in the same range as everything else. If you find you have two non-overlapping ranges active, you will need to demote one of your Routers to be only a wireless access point, not a full Router.

Test print PSC 1410

everytime i switch on my printer HP- PSC 1410 it start with a test print ,how can i avoid it. Thanks for concern.

Hi @ben51
Let's perform a hard reset. To do so, leave the printer on and unplug the power cable fro 1 minute. While it is unplugged, hold down the power button on the printer for 10-15 seconds to release any built up power, then after the minute has passed, plug the printer back in.
Also, do you have the printer connected directly to a wall outlet or is it in a surge protector or power bar? Even if you have been using a surge protector/power bar all this time and you feel it is not the cause, please connect it to a wall outlet just so we can eliminate the power source as the root cause. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector
In this document you will see, ISSUE: Problems or issues may arise when an HP LaserJet series printer is connected to an uninterruptible power supply (UPS), a power strip, or a surge protector
^ This is not limited to Laserjet printers.
If the issue persists, I am not sure what else to suggest other than to call us. If you are in Canada or US call 800 474 6836, or you can Contact HP Worldwide.
I hope this helps.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

HT4356 The printer responds to test print but I get no air printer found when I try to print mail

Why can't I print mail? I get "no air printer found" yet the printer responds to test print and I can print photos

Is your device a business one with a profile on it? You can check this out under settings/general/profiles. Profiles can restrict opening mail in applications beside the mail app.

Test print works but can't print from programs

I have installed an Officejet 6500A. Install went as expected and drivers were loaded ok. I can print a test page and the maintenance utilites will print fine but it will not print from any of the Windows programs. I am connected via USB. Any ideas would be appreciated.
Thanks.

So if I understand you correctly, the switch works with everything on the wired network (including the MacBook Pro). You can't see the wired network when connecting wirelessly on the MacBook Pro.
So you must have the switch attached to the airport extreme ethernet port. All of your other computers are attached to the switch.
Try to use the UNIX command ping in terminal.
Example :
Start terminal
ping 10.xxx.xxx.xxx
where 10.xxx.xxx.xxx is the ip of a computer on your network
This will tell you if the computer on the network is visible.

Printer install, test print ok, will not print anything else, cannot select as default printer

Printer installs fine, test pages, alignment pages, colour print pages all test fine, they are selected to print from the option on control panel. Trying to print from any other program, the printer is not listed as an option. Going through control panel, try selecting it as default printer, following messge given :
Operation could not be completed (error 0x00000709). Double check the printer name and make sure the printer is connected to the network.
Printer connected via USB direct to my single laptop. Uninstalled and re installed, as per troubleshooting instuctions. Ran troubleshooting program and HP print and scan doctor. Only info given was that it was not default printer, when asked to fix the problem it states it cannot.
Had a previous HP printer scanner, all removed (it broke, hence the new one), never had a problem with the install, this new one is being a real pain, any help would be appreciated

Hello again mattcpx ,
I think what we are going to need to do is start right from scratch. Seeing that the only printer listed is generic printer icon from Windows 7(This icon does nothing for the printer you have installed), we are going to uninstall your printer and do a proper re install.
Lets start off by removing the usb cable from both the printer and from the computer and leave it disconnected until further notice.
The first link I have for you gives detailed instructions for Uninstalling the Printer Software.
Once the uninstall is complete, please reboot the computer so that the changes take affect.
When the computer is back on, disable any firewalls or anti virus protection that you may have running.
Please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
Do a power cycle on the printer with the use of the on/off button. This will do a semi power reset on the printer.
The next step that we are going to take is to download and save the HP Officejet 4630 e-All-in-One Printer series Full Feature Software and Drivers to the desktop of the computer. This will create a new icon on the computer and make the download easy to find.
Double click on the new icon and follow the installation instructions. The installation will prompt you when to connect the usb cable so please do NOT connect it before hand.
Let me know how you make out.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP Photosmart 3150 Printer Test Print Page Problem

After 2-3 years of working fine, my printer suddenly has taken to printing a test page every time I turn it on, wasting a great deal of ink. Others have posted having a similar problem and I would llike advice on how to turn off the automatic test page printing. Thank you.

Hi there suzyq333,
This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Looking for automated way to test print PnP printer after install then delete

At times we test 20 to 30 printers in a day. I am looking for automated ways to increase the efficiency of this. I would like to simply have the printer install using PnP print a test page then delete itself after the test page or on removal. Are there any settings that can be changed on the computer to change the PnP process to make this possible. I am currently trying to learn and understand the Plug and play process so that I may find out how to get started. Any ideas would be greatly appreciated.
Thanks
This topic first appeared in the Spiceworks Community

Chris
I spent all day Googling and doing side by side comparisons of my old and new systems.
My display is a Dell U2410. It has several presets, including sRGB and Adobe RGB. I've been using sRGB.
On my OLD system, (Win XP, PsCS2, DwCS4) there seems to be no distinction between color managed and non color managed apps, even on this wide gamut display. I could capture (digital camera) in Adobe RGB, open and edit in PsCS2, save as .psd, convert to CMYK for print, or convert to sRGB for SFW. All images looked identical and they printed and displayed perfectly. I thought this was normal, and seemed logical. This also seems to be the source of my incorrect assumptions. I was trying to get my new machine to behave like my old one.
So I get this new machine (Windows 7, PsCS5, DwCS5) and now (still in sRGB display mode) all color managed apps appear de-saturated. Non color managed apps are OK. If I switch the display to Adobe RGB, color managed apps are OK, but non color managed apps are way too saturated. From my investigation, I believe this is normal behavior on a wide gamut display. I've tried changing the Control Panel > Display > Screen Resolution > Advanced settings > Color Management options, but to no avail. Either I'm missing something, or Windows 7 is doing color management differently.
It seems my only option now is to use Adobe RGB display setting for Ps, etc. and switch to sRGB for Dw and non color managed apps. Or, have 2 separate files for print and web. I've Googled 'til my eyes are numb and still not sure I'm getting this. Any enlightenment would be greatly appreciated.
Finally, I don't see an edit function here, so I can't remove my previous incorrect reply. Moderator, please feel free to do so.
Thanks

Test Print

Similar Messages

Maybe you are looking for