Thermal sensors reporting wrong values.

On my old laptop, a Dell Inspiron 1000, suddenly today the acpi THRM started reporting temperatures like 30 degrees celsius higher than they actually were. This is making it shutdown pretty quickly after startup. Since last time it worked right, I upgraded it to kernel26-2.7.5-1. I downgraded it to 4-1 and still the same problem. I checked to see if it was a hardware problem by putting an old Debian harddrive in it and booting that, and it works fine, and reports realistic temperatures. It won't boot Arch with acpi turned off in Grub for some reason. Past that, I can't keep it running long enough to see what's going on. Anybody have any ideas?

Bump. I managed to keep it up long enough to update to the latest kernel, still not working. I get a write error when I try to change the trip points (allowed write access by root). I would post some logs and dmesg, but it shuts down very shortly after running anything at all. I guess the next thing to try would be tinkering with it in a meat locker and see if that'll keep it under 65C.
I really don't feel like fooling around with Debian on this thing.

Similar Messages

Bios reporting wrong value memory

I am still running on my old AMD Athlon XP 1800+ on MS-6330 Motherboard.
I have 3 RAM slots: 512kb, 128kb, 512kb. (max allowed 1.5gb).
I have S.I.W. (Systems Information for Windows) installed that reports this as correct. However, since reinstalling XP following a drive failure, S.I.W. now reports that BIOS is reporting the wrong value; i.e. total 512kb only.
My question is; Is this a hiccup in BIOS or SIW?
Has anyone had a similar experience please?

how much the bios counts during bios post?
Quote
i.e. total 512kb only.
kb

Project cash management Reporting; wrong value in RPSCO table

Hi,
I have a problem.
I have activate the Project cash management.
I have run the transaction OPH1 for delection Actual DATA.
I have run the transaction OPH4 for reconstruction actual data for purchase orders.
Ihave run the transaction CJEN for reconstruction info database.
The customizing for the value category is green.
In the report S_ALR_87013573, we display always wrong value , tough line items (CJIA ) is blank.
We have run again the transaction OPH1 for delection Actual DATA, but we display the worng value in the table RPSCO. .
Kindly suggest me the solution.
Best Regards
Federica

hi,
execute the below reports in se38 and after that run cjbn,cjen
RKACOR19-Reconcile between line items and totals records
RKPEP010-Display Project Actual Payment Line Items
regards,

Full Points sure: Wrong values populating in report (BEX)

Hi Gurus,
I got an Issue on CRM Report. Report is populating wrong values.
In the report, We have structure called Opportunity (in that structure fields are New opportunity, Close opportunity, Win opportunity and Open opportunity) in query and One key figure called Revenue.
On revenue we have one condition with variables. But, in that condition everything is fine.
The Condition Screen is like this:
Radio Button: Single characteristic is selected
"Opportunity Sales ID" selected in Characteristics.
Keyfigures:
Revenue                      New Opp                      TOP N             TOP X OPP
Revenue                      Open Opp                     TOP N             TOP X OPP
Revenue                      WINS                           TOP N             TOP X OPP
Revenue                      Lost                             TOP N              TOP X OPP
everything is right in this: If we select top 10 opportunities. we are getting wrong values
for ex: if we select top 10 Opportunities (in the selection screen) means REVENUES.
We are getting 12 values. 10 values are correct remaining 2 values are wrong..
There is no Update routine for revenue keyfield.
Can please suggest me on this What are possibilities for wrong values ...
FULL POINTS SURE FOR THIS
THANKS,
KN

Hi All,
Can anybody answer... this...
thanks,
KR

Webi base on BW query based on Infoset comes back with wrong values

Hello:
I have a Webi report on an OLAP Universe, on Bex Query.
The bex query is based on 1 INFOSET.
When I run the webi report the values that comes back a totally wrong values.
The correct results are not brought back.
When I do a test with crystal reports to the infoset, I can see the correct values. (I'm aware crystal uses different drivers).
The test is BW query designer, and crystal brings back proper values from Infoset based BW query.
Webi on Infoset based BW Query comes back with wrong data.
query is simple.
Pull in 3 attributes, 3 key figures, where componentkey = "111"
I get 36 rows in Crystal and 36 rows in Bex Analyzer, 36 rows in BW query designer (web analyzer).
I get many rows in webi (almost like a CARTENSIAN product).
I search a round this forum but still did not see a conclusive answer to this problem.
But I see another thread that several others faced this same issue without a resolution.
My environment.
BOE XI 3.1 SP2
No fix packs
SAP IK 3.1 SP2
HPUX-IA64
Thanks in advance for any help.
Dwayne

Was this problem ever solved?
I am having a similar problem with an infoset based query.
I have created the BW infoset, and confirmed that the correct data is returned from the underlying infoproviders. A simple BW query on that infoset yields the same results.
Create the universe, and then the WEBI, and WEBI now shows hundreds of records where I expect 10. Data is being returned in WEBI that definitely shouldn't be there. It's almost like the restrictions applied in the characteristic restriction area of my BW query are being ignored, even if I include them in the WEBI query.
Cheers,
Andrew

Updated CODE1 is showing wrong values in 2LIS_05_QE1

Hi all,
I'm using 2LIS_05_QE1 extractor to report over qualitative data in BW. When the code of the characteristics is updated, the extractor takes 2 records, before and after images. The extractor is gathering wrong values for the CODE1 field in the before image.
REQUEST     DATAPAKID     RECORD     ROCANCEL     PPLNKN     MERKNR     CODE1     GRUPPE1     ZHLNSTAT
REQU_4KVR0APSV0RSZ7N70IOR0F95L     1     5120          5     40     0     CIBAU038     1
REQU_4KPIA4UG5G1IKN6DE3XFWKIS9             3     4045     X     5     40     0     CIBAU038     -1
REQU_4KPIA4UG5G1IKN6DE3XFWKIS9             3     4046          5     40     75     CIBAU038     1
REQU_4KYF8YNIEMXNZI7P2Y5BM21W9     3     4045     X     5     40     0     CIBAU038     -1
REQU_4KYF8YNIEMXNZI7P2Y5BM21W9     3     4046          5     40     75     CIBAU038     1
We have changed the characteristic two times, now we can see two of the before images with the ROCANCEL field marked with = 'X'. The problem appears in the second before image which is not taking the actual value of the CODE1 field (75), instead is showing the value in zero. Then, when I report over the key figure in the table above ZHLNSTAT (quantity of values) the results are showing 2 values for CODE1=75 and -1 values for CODE1=0.
Any ideas?

I have checked Datasource and CODE1 is not a hidden field...apart from this field there are other fields too which I can see in Datasource in R/3 about dont see them in BW ....
Please let me know what could be wrong.
Thanks,
Murtuza.
Edited by: Murtuza Morwala on Jun 27, 2009 7:36 AM

HTMLDB_APPLICATION.G_F01 has wrong value!

HTMLDB_APPLICATION.G_F01 has wrong value!
Hello again,
I have a search page in my app (here the user defines the search criteria) P1.
The page branches to P130, where the result is shown. This second page contains a region of type 'SQL Query (PL/SQL Function Body Returning SQL Query)'. The code for this dynamic query is 231 lines of code, so I want to spare you scrolling through it here . What it basically does is generating SQL QRY's such as the following:
select     distinct(sq.SAMPLE_ID) XXX,
'ID: '||sq.SAMPLE_ID||'
' ||'Type: '||sq.SAMPLE_TYPE||'
' ||'Collection Date: '||sq.COLLECTION_DATE SAMPLE_INFO,
'Aliquots (T/A): '||to_char(sq.ALIQUOTS_TOTAL)|| '/' ||to_char(sq.ALIQUOTS_AVAILABLE)||'
' ||'Volume (T/A): '||to_char(sq.VOLUME_TOTAL,'990D00')|| '/' ||to_char(sq.VOLUME_AVAILABLE,'990D00') AVAILABILITY,
'Age: '||sq.PATIENT_AGE||'
' ||'Gender: '||sq.PATIENT_SEX||'
' ||'Bloodtype: '||sq.BLOOD_TYPE||'
' PATIENT_INFO,
DML_SERVICE.get_Diagnoses(sq.SAMPLE_ID) DIAGNOSES,
DML_SERVICE.get_Medications(sq.SAMPLE_ID) MEDICATIONS,
DML_SERVICE.get_Interferences(sq.SAMPLE_ID) INTERFERENCES,
DML_SERVICE.get_LabData(sq.SAMPLE_ID) LABDATA,
decode(to_char(sq.ALIQUOTS_AVAILABLE), '0', null, htmldb_item.text(1, '1', 1, 2)) ORDER_QTY,
decode(to_char(sq.ALIQUOTS_AVAILABLE), '0', null, htmldb_item.checkbox(2,sq.SAMPLE_ID)) ORDER_ME
from SEARCH_V01 sq
where sq.DIAGNOSIS = 'D-Dimer'
order by 1 desc
The DML_SERVICE functions just return a string(Varchar2). At the right side of the report I have two columns, one with a textfield (ORDER_QTY, default: 1) and one with a checkbox (ORDER_ME) for each line.
For each line where the checkbox is checked, a process (On Submit - after Comp and Val) places the order for the requested quantity (this is done by inserting an Order ID into the ALIQUOTS table -> see bold update statement below).
The process follows:
declare
alq_qty number;
alq_id number;
cnt number;
begin
cnt := 0;
for i in 1..HTMLDB_APPLICATION.G_F02.count
loop
select count(*) -- set alq_qty to number of available alq's
into alq_qty
from ALIQUOTS a
where a.SAMPLE_ID = HTMLDB_APPLICATION.G_F02(i)
and a.ORDER_ID = 0;
insert into D_DEBUG (ID, DD) values (1, 'wanted: ' || HTMLDB_APPLICATION.G_F01(i) || ' available: ' || alq_qty); -- REMOVE!!!
if alq_qty > to_number(HTMLDB_APPLICATION.G_F01(i)) then -- if there are enough alq's
alq_qty := to_number(HTMLDB_APPLICATION.G_F01(i)); -- set alq_qty to number of ordered alq's
end if;
for n in 1..alq_qty
loop
select min(ID)
into alq_id
from ALIQUOTS
where sample_id = HTMLDB_APPLICATION.G_F02(i)
and order_id = 0;
insert into D_DEBUG (ID, DD) values (1, 'alq_id: '||alq_id); -- REMOVE!!!
update ALIQUOTS
set order_id = :P130_SELECT_ORDER
where id = alq_id;
cnt := cnt + 1;
end loop;
dml_service.upd_sample_record(HTMLDB_APPLICATION.G_F02(i)); -- refresh data in SAMPLE table
end loop;
:P130_MSG := 'Assigned '||cnt||' aliquots to order: '||:P130_SELECT_ORDER;
end;
Now my problem is that this process does what it should, sometimes. When I enter 6 in one row and check the checkbox and enter 4 in another row and check that checkbox and then press SUBMIT, 10 aliquots are assigned to my order.
Sometimes.... the other times the process just orders 2 aliquots, one of each line and disregards the number entered in the textfield.
Or so it may seem: I added some lines to write debug info into D_DEBUG (see above.) From those entries you can assume that the content of HTMLDB_APPLICATION.G_F01(i) is in fact '1' when the process does its work. So I think the problem lies somewhere in the creation of htmldb_item.text(), (I went through the API of that htmldb_item again and again...)
Also: I can reproduce / recreate this error. It's totally weird: for some rows it (always) works and for some it (always) doesn't !!!
So, any help, any suggestion is really appreciated (I'm currently working on bringing the crucial part of this to marvel.oracle.com)
-David-
[Edited by: sleuniss on Jul 15, 2004 12:18 PM]
Changed subject line.

Now the subjectline is right, but the indentation is gone.... :-(
again the SQL query:
select     distinct(sq.SAMPLE_ID) XXX,
           'ID: '||sq.SAMPLE_ID||'
' ||'Type: '||sq.SAMPLE_TYPE||'
' ||'Collection Date: '||sq.COLLECTION_DATE SAMPLE_INFO,
           'Aliquots (T/A): '||to_char(sq.ALIQUOTS_TOTAL)|| '/' ||to_char(sq.ALIQUOTS_AVAILABLE)||'
' ||'Volume (T/A): '||to_char(sq.VOLUME_TOTAL,'990D00')|| '/' ||to_char(sq.VOLUME_AVAILABLE,'990D00') AVAILABILITY,
           'Age: '||sq.PATIENT_AGE||'
' ||'Gender: '||sq.PATIENT_SEX||'
' ||'Bloodtype: '||sq.BLOOD_TYPE||'
' PATIENT_INFO,
           DML_SERVICE.get_Diagnoses(sq.SAMPLE_ID) DIAGNOSES,
           DML_SERVICE.get_Medications(sq.SAMPLE_ID) MEDICATIONS,
           DML_SERVICE.get_Interferences(sq.SAMPLE_ID) INTERFERENCES,
           DML_SERVICE.get_LabData(sq.SAMPLE_ID) LABDATA,
           decode(to_char(sq.ALIQUOTS_AVAILABLE), '0', null, htmldb_item.text(1, '1', 1, 2)) ORDER_QTY,
           decode(to_char(sq.ALIQUOTS_AVAILABLE), '0', null, htmldb_item.checkbox(2,sq.SAMPLE_ID)) ORDER_ME
from     SEARCH_V01 sq
where sq.DIAGNOSIS = 'D-Dimer'
order    by 1 desc
and the process:
declare
   alq_qty number;
   alq_id number;
   cnt number;
begin
   cnt := 0;
   for i in 1..HTMLDB_APPLICATION.G_F02.count
   loop
      select count(*) -- set alq_qty to number of available alq's
       into alq_qty
       from ALIQUOTS a
       where a.SAMPLE_ID = HTMLDB_APPLICATION.G_F02(i)
       and a.ORDER_ID = 0;
insert into D_DEBUG (ID, DD) values (1, 'wanted: ' || HTMLDB_APPLICATION.G_F01(i) || ' available: ' || alq_qty); -- REMOVE!!!
      if alq_qty > to_number(HTMLDB_APPLICATION.G_F01(i)) then -- if there are enough alq's
         alq_qty := to_number(HTMLDB_APPLICATION.G_F01(i)); -- set alq_qty to number of ordered alq's
      end if;
      for n in 1..alq_qty
      loop
         select min(ID)
          into alq_id
          from ALIQUOTS
          where sample_id = HTMLDB_APPLICATION.G_F02(i)
          and order_id = 0;
insert into D_DEBUG (ID, DD) values (1, 'alq_id: '||alq_id); -- REMOVE!!!
         update ALIQUOTS
          set order_id = :P130_SELECT_ORDER
          where id = alq_id;
         cnt := cnt + 1;
      end loop;
      dml_service.upd_sample_record(HTMLDB_APPLICATION.G_F02(i)); -- refresh data in SAMPLE table
   end loop;
   :P130_MSG := 'Assigned '||cnt||' aliquots to order: '||:P130_SELECT_ORDER;
end;
-David-

Wrong value with calculated item in pivot table

I have a report with 4 columns:
First Column are Department Dimension
Second Column is Actual value
Third Column is Previous value
Four Column is: ((Actual Value-Previous Value)/Previous Value))*100 that called Var
Then I do a pivot table and I have new calculated item: Department1/Department2 and I have wrong value in four column:
Department----------------------------------Actual-------Previous------Var
Dept1------------------------------------------18503--------16308--------13,5
Dept2-------------------------------------------3758---------3518----------6,8
(Calculated Item: Dept1/Dept2)--------4,92---------4,64------------*2* <---- This value is wrong...and it has to be: 6,03
Is possible to get the correct value???
Thank you very much!

hi,
Create a logical column with ur calculation formula and make it as default agg rule in rpd and answers change it to server determined/server complex agg.I did the same it was working fine for me!!
Check this link
http://books.google.com/books?id=OnbYrkWa4RsC&pg=PA74&lpg=PA74&dq=%22server+complex+aggregate%22&source=web&ots=qxrpaFXmo2&sig=CxLOemzcOlvIiaQ_sQD4fPQotdM&hl=en&sa=X&oi=book_result&resnum=5&ct=result#v=onepage&q=%22server%20complex%20aggregate%22&f=false
thanks,
saichand

Wrong values in the cube S001.

good morning people,
we are with the ecc 6.0 installed almost 01 years, the analysis made in the reports that use the standard cube S001, are with with wrong values. This problem does not happen with all materials in a given month, it appears as if the quantity to be addressed in pending orders, but referring to VA05 or VA05N shows nothing pending.
Being a standard table is not my IT team can not change it, someone already went through this problem, how did you solve it.
Since will thank you.
Jefferson Souza
Multilab Ind e Com Prod Farmaco Ltda
Brazil

Hello Jefferson
Can you elaborate a bit more? When you say cube S001, I think you mean Infostructure S001 which is part of Sales Information System (SIS) reporting. What key figures are showing wrong? Is it open orders quantity/value? Are VA05 or VA05N showing correct values?
Check if you are using any formulas for updates- T code MC26- I doubt it becasue it is a standard table. If they are using custom formulas, may be they are the culprit.
Sometimes document status is not updated and so VA05, VA05N may not be correct. Run reports SDVBUV00, SDVBUK00 and RVV05IVB. Use OSS notes 106567, 128947 for tips before running the reports.

Add on XL reporter : Wrong executable digital signature for Add on

Hi Experts,
I have a client who gets this error 'Add on XL reporter : Wrong executable digital signature for Add on' when they try to login. They are on 2007A PL45. This happens on the server as well as on clients. Uninstalll and reinstall of client didn't work. We had a look at the AddonLocalRegistration folder to see if XL reporter is registered but can't see any.
I have found a similar link in the forum but that says about 2005b.
Any help will be appreciated.
regards
Johnson

Sir,
Please do the following steps :
1. Please go to the SBO-COMMON database, find table SARI, you will get
the data entry for your Addon. Please check the value of field
"AddOnChk". This is the digital signature of Addon executable file.
2. Then go to installer package of the Addon, open the ard file
(XLReporter.ard) with notepad then check the value of "addonsig".
3. Compare these two values, if they are different, please overwrite
"AddOnChk" field in database with the value of "addonsig" in ard file.
and then try to start the addon again.
4. If there are the same, the ard file or the executable file has been
corrupted. I would like to suggest you remove the installer package
from your machine, and download a fresh installer of Addon from SAP
Service Marketplace. After that, please follow the steps as per the
attached note ( Note no. 819501 ) to make your machine clean and
then install the addon again.
Regards,
AVTAR SINGH

Virtual Key Figure in report giving values

Hi Gurus,
I have created a Virtual Key Figure on a Multi Provide and completed all necessary user-exit coding.
When I run the BEX report for a single material my Key Figure is populating correct values.
But when I run the BEX report for multiple material and if the key figure value is zero it is putting star and due this my result is giving me the wrong value.
Please suggest me what I need to do to correct this.
Thanks,
Saleem.

Hi,
Thank you for your responace.
But still i am getting the same error. While displaying on BEX report some rows showing * and some rows showing ERROR after the value.
Please advice me .
Thanks,
Saleem.

Webi displays null and wrong values after BW upgraded to SP6

Hi,
Webi report retrieves blank values after BW Backend upgraded to SP6.
We were on SAP EHP 1 for SAP Net Weaver 7.0 and SP4. On the BO side we are on BO XI R/3 FP 2.1.
Once we add new filters to a simple webi query the webi displays the null values for the characteristics which already exist in the report and more ever wrong values displayed for few columns. We have checked the MDX query in BW by using 'MDXTEST' and the results are good.
It looks like that it is a rendering issue in Webi side and exactly no idea...
Can anybody know how to fix the issue or any SAP notes exists for resolving this?
Thank you,
Regards,
Satya

Hi Ingo,
We are also facing the same issue that satya is facing.
We have developed the reports in BO XI 3.1 SP2 FP2.1 and SAP BW 7.01 EHP1 which was running correctly and showing the right result.
But we upgraded the BW system to SAP BW 7.01 SP6 and check the WebI reports which was showing the unexpected results. ( instead of n rows it shows only 1 row for any query without dimension values)
So we upgraded the BO sys to BO XI 3.1 SP2 FP 2.6 and checked the result but no luck with that also.
The workaround i found is i must need to add the Node objects from the universe in the Query which are also used in the query filter of Web Intelligence. But this is not reliable as we need to change all the developed queries.
We have also tried to perform the things shown in the notes but no MDX trace is enabling.
Please let me know if there is any other solution.

ALV grid abort processing, if wrong value

Hello,
i've a editable alv grid.
Is it possible to abort at event data_changed/data_changed_finished, if an value is wrong (f.e. to high < 500), and write the old value back.
Best regards,
TomSd

Hello Thomas
The sample report <b>ZUS_SDN_ALVGRID_EDITABLE_10</b> provides a possible (perhaps not the most elegant) solution for your problem.
*& Report ZUS_SDN_ALVGRID_EDITABLE_10
*& Description: Reset false values entered in editable ALV list
*&              to original values
*& Example:     Column SORT_KEY allows values from '000'-'150'
*               -> reset if value > '010'
*& Thread: ALV grid abort processing, if wrong value
*& Link: https:||<a class="jive_macro jive_macro_thread" href="" __jive_macro_name="thread" modifiedtitle="true" __default_attr="669430"></a>
REPORT zus_sdn_alvgrid_editable_10.
TYPE-POOLS: abap.
INCLUDE <icon>. " NOTE: replace by TYPE-POOLS: icon. on >= 6.20
DATA:
gd_repid         TYPE syrepid,
gd_okcode        TYPE sy-ucomm,
gs_layout        TYPE lvc_s_layo,
gt_fcat          TYPE lvc_t_fcat,
go_docking       TYPE REF TO cl_gui_docking_container,
go_grid          TYPE REF TO cl_gui_alv_grid.
TYPES: BEGIN OF ty_s_outtab.
INCLUDE TYPE knb1.
TYPES: END OF ty_s_outtab.
TYPES: ty_t_outtab    TYPE STANDARD TABLE OF ty_s_outtab
                      WITH DEFAULT KEY.
DATA:
gt_outtab        TYPE ty_t_outtab,
gt_outtab_pbo    TYPE ty_t_outtab.
*       CLASS lcl_eventhandler DEFINITION
CLASS lcl_eventhandler DEFINITION.
PUBLIC SECTION.
    CLASS-DATA:
      mo_data_changed    TYPE REF TO cl_alv_changed_data_protocol.
    CLASS-METHODS:
      handle_data_changed
        FOR EVENT data_changed OF cl_gui_alv_grid
        IMPORTING
          er_data_changed
          e_onf4
          e_onf4_before
          e_onf4_after
          e_ucomm
          sender,
      handle_data_changed_finished
        FOR EVENT data_changed_finished OF cl_gui_alv_grid
        IMPORTING
          e_modified
          et_good_cells,
      handle_user_command
        FOR EVENT user_command OF cl_gui_alv_grid
        IMPORTING
          e_ucomm,
      handle_toolbar
        FOR EVENT toolbar OF cl_gui_alv_grid
        IMPORTING
          e_object
          e_interactive.
ENDCLASS.                    "lcl_eventhandler DEFINITION
*       CLASS lcl_eventhandler IMPLEMENTATION
CLASS lcl_eventhandler IMPLEMENTATION.
METHOD handle_data_changed.
*   define local data
    DATA:
      ld_idx     TYPE i,
      ls_cell    TYPE lvc_s_modi,
      ls_msg     TYPE symsg.
    FIELD-SYMBOLS:
      <lt_outtab> TYPE ty_t_outtab,
      <ls_outtab> TYPE ty_s_outtab.
    ASSIGN er_data_changed->mp_mod_rows->* TO <lt_outtab>.
    LOOP AT er_data_changed->mt_mod_cells INTO ls_cell
            WHERE ( fieldname = 'ZUAWA' ).
      ld_idx = syst-tabix.
      IF ( ls_cell-value <= '010' ).
        READ TABLE <lt_outtab> ASSIGNING <ls_outtab> INDEX ld_idx.
        MODIFY gt_outtab FROM <ls_outtab> INDEX ls_cell-row_id. " !!!
      ELSE.
        CLEAR: ls_msg.
        ls_msg-msgv1 = 'Value'.
        ls_msg-msgv2 = ls_cell-value.
        ls_msg-msgv3 = 'too high (> 010)'.
        CALL METHOD er_data_changed->add_protocol_entry
          EXPORTING
             i_msgid     = '00'
             i_msgty     = 'E'
             i_msgno     = '398'
             i_msgv1     = ls_msg-msgv1
             i_msgv2     = ls_msg-msgv2
             i_msgv3     = ls_msg-msgv3
*             I_MSGV4     =
             i_fieldname = ls_cell-fieldname
             i_row_id    = ls_cell-row_id
             i_tabix     = ls_cell-tabix.
        DELETE er_data_changed->mt_mod_cells INDEX ld_idx.
        DELETE er_data_changed->mt_good_cells INDEX ld_idx.
      ENDIF.
    ENDLOOP.
    IF ( syst-subrc = 0 ).
      er_data_changed->display_protocol( ).
    ENDIF.
**    cl_gui_cfw=>set_new_ok_code( 'REFRESH' ). " not possible on 4.6c
    CALL METHOD cl_gui_cfw=>set_new_ok_code
      EXPORTING
        new_code = 'DUMMY'
*      IMPORTING
*        RC       =
ENDMETHOD.                    "handle_data_changed
METHOD handle_data_changed_finished.
*   define local data
    DATA:
      ls_outtab      TYPE ty_s_outtab,
      ls_cell        TYPE lvc_s_modi.
ENDMETHOD.                    "handle_data_changed_finished
METHOD handle_user_command.
ENDMETHOD.                    "handle_user_command
METHOD handle_toolbar.
*   define local data
    DATA:
      ls_button    TYPE stb_button.
    ls_button-function = 'DEFAULT'.
    ls_button-icon      = icon_mass_change.
    ls_button-quickinfo = 'Set default value for column'.
    APPEND ls_button TO e_object->mt_toolbar.
ENDMETHOD.                    "handle_toolbar
ENDCLASS.                    "lcl_eventhandler IMPLEMENTATION
START-OF-SELECTION.
SELECT * FROM knb1 INTO TABLE gt_outtab UP TO 20 ROWS
    WHERE bukrs = '1000'.
gt_outtab_pbo = gt_outtab. " store PBO data
* Create docking container
CREATE OBJECT go_docking
    EXPORTING
      parent                      = cl_gui_container=>screen0
      ratio                       = 90
    EXCEPTIONS
      OTHERS                      = 6.
IF sy-subrc <> 0.
*   MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*              WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
* Create ALV grid
CREATE OBJECT go_grid
    EXPORTING
      i_parent          = go_docking
    EXCEPTIONS
      OTHERS            = 5.
IF sy-subrc <> 0.
*   MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*              WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
* Build fieldcatalog
PERFORM build_fieldcatalog.
PERFORM set_layout.
SET HANDLER:
    lcl_eventhandler=>handle_toolbar               FOR go_grid,
    lcl_eventhandler=>handle_data_changed          FOR go_grid,
    lcl_eventhandler=>handle_data_changed_finished FOR go_grid.
* Display data
CALL METHOD go_grid->set_table_for_first_display
    EXPORTING
      is_layout       = gs_layout
    CHANGING
      it_outtab       = gt_outtab
      it_fieldcatalog = gt_fcat
    EXCEPTIONS
      OTHERS          = 4.
IF sy-subrc <> 0.
*   MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*              WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
go_grid->set_toolbar_interactive( ).
CALL METHOD go_grid->register_edit_event
    EXPORTING
      i_event_id = cl_gui_alv_grid=>mc_evt_enter
    EXCEPTIONS
      error      = 1
      OTHERS     = 2.
IF sy-subrc <> 0.
*   MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*              WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
* Link the docking container to the target dynpro
gd_repid = syst-repid.
CALL METHOD go_docking->link
    EXPORTING
      repid                       = gd_repid
      dynnr                       = '0100'
*      CONTAINER                   =
    EXCEPTIONS
      OTHERS                      = 4.
IF sy-subrc <> 0.
*   MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*              WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
* ok-code field = GD_OKCODE
CALL SCREEN '0100'.
* Flow logic (no elements on screen):
* PROCESS BEFORE OUTPUT.
*    MODULE STATUS_0100.
* PROCESS AFTER INPUT.
*    MODULE USER_COMMAND_0100.
END-OF-SELECTION.
*&      Module STATUS_0100 OUTPUT
*       text
MODULE status_0100 OUTPUT.
SET PF-STATUS 'STATUS_0100'.
* SET TITLEBAR 'xxx'.
CALL METHOD go_grid->refresh_table_display
*      EXPORTING
*        IS_STABLE      =
*        I_SOFT_REFRESH =
    EXCEPTIONS
      finished       = 1
      OTHERS         = 2.
IF sy-subrc <> 0.
*     MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*                WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDMODULE.                 " STATUS_0100 OUTPUT
*&      Module USER_COMMAND_0100 INPUT
*       text
MODULE user_command_0100 INPUT.
TRANSLATE gd_okcode TO UPPER CASE.
* Fetch changes on ALV grid
go_grid->check_changed_data( ).
CASE gd_okcode.
    WHEN 'BACK' OR
         'END' OR
         'CANC'.
      SET SCREEN 0. LEAVE SCREEN.
    WHEN 'DUMMY'. " do nothing but pass PAI -> list refresh at PBO
    WHEN OTHERS.
ENDCASE.
CLEAR: gd_okcode.
ENDMODULE.                 " USER_COMMAND_0100 INPUT
*&      Form BUILD_FIELDCATALOG_KNB1
*       text
* --> p1        text
* <-- p2        text
FORM build_fieldcatalog .
* define local data
DATA:
    ls_fcat        TYPE lvc_s_fcat.
CALL FUNCTION 'LVC_FIELDCATALOG_MERGE'
    EXPORTING
*     I_BUFFER_ACTIVE              =
      i_structure_name             = 'KNB1'
*     I_CLIENT_NEVER_DISPLAY       = 'X'
*     I_BYPASSING_BUFFER           =
*     I_INTERNAL_TABNAME           =
    CHANGING
      ct_fieldcat                  = gt_fcat
    EXCEPTIONS
      inconsistent_interface       = 1
      program_error                = 2
      OTHERS                       = 3.
IF sy-subrc <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
*         WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
" Set required fields editable
LOOP AT gt_fcat INTO ls_fcat
                  WHERE ( fieldname = 'ZUAWA' OR
                          fieldname = 'BUSAB' ).
    ls_fcat-edit    = abap_true.
    MODIFY gt_fcat FROM ls_fcat.
ENDLOOP.
DELETE gt_fcat WHERE ( fieldname = 'ZINRT' ).
ENDFORM.                    " BUILD_FIELDCATALOG
*&      Form SET_LAYOUT
*       text
* --> p1        text
* <-- p2        text
FORM set_layout .
CLEAR: gs_layout.
gs_layout-cwidth_opt = abap_true.
gs_layout-zebra      = abap_true.
** gs_layout-stylefname = 'CELLTAB'.
ENDFORM.                    " SET_LAYOUT
Regards,
Uwe

Non thermal sensor RAM

Greetings,
From the OWC memory upgrade page, it is stated that its DDR3 RAM are with thermal sensors. I wonder now whether RAMs without thermal sensor are compatible. I'm looking at Kingstion value ram at the moment. Thanks

George, you didn't mention you have special needs and a vendor that ships to Asia. You mentioned OWC, so thought that was where you were thinking of buying or have used before.
Australia and Japan, So Korea, and you haven't found a vendor?
KTA only
Like Cruical, use the Kingston memory selector to find what they support for a specific model. Manufacturer System PN: MB535LL/A; MB535X/A
KTA-MP1066K3/6G - Part Detail
6GB 1066MHz DDR3 ECC Kit

Enabling Thermal Sensors on Conky

Hi everyone, Im having a hard time enabling the thermal sensors for my conky. I get only a cpu sensor which uses this script.
${color #888888}CPUTEMP:${color #CCCCCC} ${acpitemp}C
I've already installed lm-sensors and hddtemp.
What's the command for enabling them?
And by the way, the script above doesn't even move or rises...It stucks on 4O C...And I assume that this is a System Temp not the cpu temp..Correct me if I'm wrong.;)
All help would be appreciated... Thanks...all
Last edited by kaola_linux (2008-11-23 03:16:07)

Dunno about that specific one (acpitemp gives me nothing), but do you have anything in /sys/bus/platform/devices? Like:
coretemp.0 coretemp.1 i8042 iTCO_wdt it87.656 pcspkr serial8250 vesafb.0
it87.656 has:
alarms fan4_input in2_min in6_input pwm2 temp2_max
bus fan4_min in3_alarm in6_max pwm2_enable temp2_min
cpu0_vid hwmon:hwmon0 in3_input in6_min pwm2_freq temp2_type
driver in0_alarm in3_max in7_alarm pwm3 temp3_alarm
fan1_alarm in0_input in3_min in7_input pwm3_enable temp3_input
fan1_input in0_max in4_alarm in7_max pwm3_freq temp3_max
fan1_min in0_min in4_input in7_min subsystem temp3_min
fan2_alarm in1_alarm in4_max in8_input temp1_alarm temp3_type
fan2_input in1_input in4_min modalias temp1_input uevent
fan2_min in1_max in5_alarm name temp1_max vrm
fan3_alarm in1_min in5_input power temp1_min
fan3_input in2_alarm in5_max pwm1 temp1_type
fan3_min in2_input in5_min pwm1_enable temp2_alarm
fan4_alarm in2_max in6_alarm pwm1_freq temp2_input
My ambient temp reading, and root HDD are gotten with:
${platform it87.656 temp 2}, ${hddtemp sda}
The exact names may vary.
DE panel plugins may be helpful in figuring out which exactly is which. FI, I got a bunch of temps showing w/ XFCE's sensors plugin, then loaded my PC for awhile, to get what was what (except CPU and HDD). Quicker and easier than using conky or sensors for figuring them out.
Last edited by cerbie (2008-11-23 12:09:52)

Thermal sensors reporting wrong values.

Similar Messages

Maybe you are looking for