This warning appears in Event Viewer every day on T530 w/ Win7-64

Event 37, Kernel-Processor-Power
The speed of processor [0,1,2,3] in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 86398 seconds since the last report.
Can anything be done to fix this?

I assume you are running on AC power. Look in the power manager. My settings are set to "maximum performance", when running on AC. Also, the CPU can be slowed down if you are running too hot. If the power settings were already set to maximum performance, run a temperature monitor program. I use TPFANCONTROL (free)

Similar Messages

My iPhone 4 appears with no service every day, i have to restarted and a few hours later again the same problem, Any other solution please???

my iPhone 4 appears with no service every day, i have to make restart and a few hours later again the same problem, Any other solution please???

This is almost always a symptom of a phone that was jailbroken or hacked to unlock it.
Where did you get the phone?

Application Nividia Stream error and warning in the Event Viewer Windows 8.1

Have found the following repeating error and warning in the Event Viewer Windows 8.1 64 bit reg.the application Nividia Stream:
1. The error :
"Can not find the description of event 2001 identification from
the source NvStreamSvc.
Either the component causing this issue is not
installed in the local computer or installation is broken. You can install or
repair the component in the computer.
Information to the event :
NvStreamSvc
Failed continue stopping [6] "
2. The warning :
"Can not find the description of event 2002 identification
from the source NvStreamSvc.
Either the component causing this issue is not
installed in the local computer or installation is broken. You can install or
repair the component in the computer.
Information to the event
NvStreamSvc
SSAU process ID 7820 did not exit, Termination.
[6]”
I would appreciate the advice how to fix it.
Thanks and best regards,
Ewa

Hi,
Thanks for your reply.
Have the lastest updated Nividia driver : version 347.88 - shall I uninstall and install again ?
Shall I make express installation /as usually/ or advanced ?
Reg. Nividia Stream service - shall I disable this service in services.msc ?
The software - now have Nividia GeForce Experience updated to the version 2.4.1.21 on 30th
March.
Would appreciate your further assistance and help.
Thanks and best regards, Ewa

Calendar events showing every day

Hi all,
Recently it seems that when my Calendar app is displaying month view, every day has a little square in it - the one that indicates an event. However, about half of my days have no events at all.
I have repeating events set every eight days for four days (for my four-on four-off shift rotation) but that's about all. I'm sure I remember it used to show correctly, i.e. blocks of four with events and blocks of four without.
Anyone any ideas what's happened?
Thanks for reading
BBz

I have the same problem. With me it is only on the "Birthdays" calendar which was uploaded from iCal to my calendar server before I went with syncing with CalDAV. The daily and list formats do not show anything weird, only the monthly view. I assume it is a problem with a repeating event, but I can't find it.
I've even done a reset and reload from backup of my iPod and it did not help. Next step is probably to delete the Birthday's calendar completely on my server and see if that cures the problem. I am waiting until there is an easy way to restore it on the server.
Any other ideas would be appreciated.

Invoiced delivery appearing in billing due every day.

Hi Guys,
Please let me know any correction programs available for this issue.
Invoiced delivery appearing in billing due every day.
It is appearing in financial posting for due V.21 like billing due every day.
I have tried those correction programs
RVDELSTA
RVV05IVB
SDVBUK00 no yet resolved.
Thanks in advance.
Regards,
Sathiesh Pillai.

Hi Siva,
Thanks for your replay.
I have tried those notes before. I have same order like that before and after.
It looks Odd. All documents are completed.
Note 127514 - Change of billing relevancy without effect. why i am not tried this note know, it is relevant for item category billing relevant field changes..we are not changed anything.. I don't think so it will help me.
Regards,
Sathiesh Pillai.

TS4118 When I print out my ical calendars, there are three duplicate events happening every day of the week and I never entered this event?

When I print out my calendars from ical, there is one event that is reoccurring 3x/day/every day of week! It is not showing on the actual calendar and I cannot figure out how or where it's coming from? It's in the calendar marked Jimmys action which just shows my sons activities and for this activitiy, I put one day with a recurring weekly on just two days of the week at a specific time and this is showing up as well and correctly? What should I do to remedy this?

UPDATE: I think I found the answer to my problem. I travel between two time zones and recently started listing event times as "floating" so they don't get messed up when I travel between west and east coasts. It seems that when I want to print out a calendar sheet, the time of the event doesn't show up if it's a "floating" event. So, I need to go back to putting a time zone in and turning off "time support" in Preferences for iCal. BTW this (in reverse) is a solution for those who don't want to see appointment times printed out – make it a "floating" event.

Event viewer warning

Hi!
So, the problem started after I moved the BusinessObjects XI 3.1 server from hardware environment to a virtual environment.
This is the event log warning:
Unable to contact server EEEL132.WebApplicationContainerServer on machine eeel132 to perform status notification. Please check the server's system log for errors.
EEEl132 is the hostname of the server.
Event ID is 33017
Source BusinessObjects_CMS
Any idea how to remove the warning from the event viewer and fix the problem?
Regards,
Tarvi

http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_troubleshooting_guide_chapter09186a008011b369.html#wp1047403
Browser Service: Every 2 Hours, an Error Occurs in the Event Log on the Subscriber
Symptom
Error Message The browser server has failed to retrieve the backup
list too many times on transport \Device\netBT_Tcpip (c96xxx)
The backup browser is stopping.
Warning: The browser was unable to retrieve a list of servers from the browser master \\AACCMP1 on the network \Device\netBT_Tcpip (c96xxx) the data is the error code.
Probable Cause
Cause indicates a NIC card problem. You need to upgrade the OS to a newer version.
Corrective Action
Procedure
Step 1 If you have an MCS-7830 and build the OS with the new 2000.1.2 OS installation, run the OS upgrade version 2000.1.3 to fix the NIC card problem.
If this is not your problem, verify the following actions:
Step 2 Ensure that your WINS address is correct.
Step 3 Ensure that Enable NetBIOS over TCP/IP is chosen.
Step 4 Ensure that the WINS address is correct on the master browser \\AACCM1.
Cheers
Please rate post if helpful.

Dots Every Day in Calendar Month View

I have the dots indicating an event on every day of the monthly view in the calendar even though there aren't any events on those dates. I am syncing with Outlook 2003 on Windows XP. I have read through posts here and:
- Had some birthdays set up in the contacts but removed them
- Do not have any events where the end time is earlier than the start time
I have tried many different things including turning calendar syncing off, replacing all of the info for calendars, etc. but cannot get it fixed.
Any other suggestions? How can I delete the info on the Calendar. Turning off syncing doesn't do it. Do I need to do a full reset?
Thanks.

Thanks. Your suggestion did the trick.
I assumed it marked every date in perpetuity with a dot. I went backwards until I found a month without a dot. After a couple of dozen clicks on the back arrow, I realized if I held it down it would go faster.
Went back to 1971 and found an entry for a birth date. The interesting thing is, is that it was in October. November looked fine and then in December, the dots started occurring. Deleted the entry and everything looks good again.
Thanks.

Calendar has marked every day in monthly view

Hello,
I'm using my (German) 3G with Exchange Active Sync. It works fine except for one problem. The monthly calendar marks a event for every day with the small rectangle. This makes it of course difficult, to identify a day where a event exist.
Any idea, how to solve this?
Regards

Hornfrosch wrote:
Hello,
I'm using my (German) 3G with Exchange Active Sync. It works fine except for one problem. The monthly calendar marks a event for every day with the small rectangle. This makes it of course difficult, to identify a day where a event exist.
Any idea, how to solve this?
Regards
Just to bring it up again, here you can see a screenshot:
http://www.av3.de/003.png

Windows is Scanning and repairing drive... (- Errors in Event Viewer)

Long post, please be patient... :)
I have a fairly new (purchased 8/2013) Lenovo ThinkPad T431s with Windows 8.1 Pro 64-bit (updated from 8.0 -> 8.1). It has a very tricky error coming basically 8 / 10 boots:
Windows is Scanning and repairing drive...
Error details from Windows Event Viewer (a new similar error appears on every boot to event viewer):
A corruption was discovered in the file system structure on volume \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}.
A file on the volume is no longer reachable from its parent directory. The parent file reference number is 0x2000000000002. The name of the parent directory is "". The parent index attribute is ":$I30:$INDEX_ALLOCATION". The file reference
number of the file that needs to be reconnected is 0x400000003db80. There may be additional files on the volume that also need to be reconnected to this parent directory.
What has been done 1st trying to fix that:
SSD disk has been changed (image from previous SSD copied back) ->
no solution, error remains
chkdsk /F /R -> no solution, error remains
SFC /scannow -> no solution, error remains
dism /online /cleanup-image /restorehealth -> no solution, error remains after a few boots
TRIED using Windows 8.1 "Update & Recovery -> Refresh Your PC without affecting your files" -> Inserted the Lenovo "Operating System Recovery Disk Windows 8 Pro (OEM Activation 3.0 Required)" BUT Windows did not accept
that DVD claiming "The media inserted is not valid"... ???
Ended up calling Lenovo Support and they instructed me to order the Recovery DVD from
Lenovorecovery.com -> Unfortunatelly Windows does not recognice the DVD(s)...
mountvol returns:
\\?\Volume{4d337687-0033-42f7-8a8e-b6968b533cb3}\
(This is my C:\ drive where Windows installation resides)
\\?\Volume{e010cf9d-c04d-4c82-b517-3cda1b647fe7}\
*** NO MOUNT POINTS ***
\\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}\
*** NO MOUNT POINTS ***
\\?\Volume{33f0062f-0aff-4fd2-8402-1c7911d86897}\
*** NO MOUNT POINTS ***
Then running fsutil dirty query on each returns:
Volume - \\?\Volume{4d337687-0033-42f7-8a8e-b6968b533cb3} is NOT Dirty
Volume - \\?\Volume{e010cf9d-c04d-4c82-b517-3cda1b647fe7} is NOT Dirty
Volume - \\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} is Dirty
Volume - \\?\Volume{33f0062f-0aff-4fd2-8402-1c7911d86897} is NOT Dirty
The chkdsk on the dirty volume
\\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}\ returned:
The type of the file system is NTFS.
Insufficient storage available to create either the shadow copy storage file or
other shadow copy data.
A snapshot error occured while scanning this drive. Run an offline scan and fix.
Diskpart output on the same volume:
DISKPART> lis par
Partition ### Type Size Offset
Partition 1 Reserved 128 MB 17 KB
Partition 2 Recovery 1000 MB 129 MB
Partition 3 System 260 MB 1129 MB
Partition 4 Primary 146 GB 1389 MB
Partition 5 Recovery 350 MB 147 GB
Partition 6 Recovery 19 GB 148 GB
Questions:
1) Are my Partitions OK, haven't "touched" anything?
2) Excluded the dirty volume from boot checking with chkntfs /x
-> still the Error appears in Event viewer log (but Scanning is skipped/not shown anymore during the boot).
What is causing the error?
3) Why do I have three (3) recovery partitions?

What has happened in the past days:
A) Lenovo on-site-Support changed the motherboard -> had no impact on the error (which I expected).
B) I found
instructions how to manually create USB Flash stick with a booting Custom (OEM) Recovery Image.
C) Booted with USB and performed "Refresh your PC without affecting your files."
D) Windows was refreshed but...
-->>
Still the error remains (Windows scanning and repairing drive \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} on each and every boot.
1) Related Error in Event viewer (NTFS):
A corruption was discovered in the file system structure on volume \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984}.
A file on the volume is no longer reachable from its parent directory. The parent file reference number is 0x2000000000002. The name of the parent directory is "". The parent index attribute is ":$I30:$INDEX_ALLOCATION". The file reference number of the
file that needs to be reconnected is 0x400000003db80. There may be additional files on the volume that also need to be reconnected to this parent directory.
2) Related Error in Event viewer (NTFS - Microsoft Windows NTFS):
Volume \\?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} (\Device\HarddiskVolume5) needs to be taken offline to perform a Full Chkdsk. Please run "CHKDSK /F" locally via the command line, or run "REPAIR-VOLUME <drive:>" locally or remotely via
PowerShell.
-->>
Now Lenovo support is proposing a full re-install (to be performed by myself) of Windows as this is SW issue.
Summary:
- Refreshing my T431s with OEM Image does not help
- The error remains on \?\Volume{f62db2cf-efe4-4b55-a3f7-0e7db991a984} (\Device\HarddiskVolume5; Lenovo Recovery partition) OR at least Windows thinks so...

SCHANNEL Fatal Alert:80 in Event Viewer

See a post in 2012 that tweaks the registry to set the alert to O thus eliminating the alert but it doesn't explain why it happens or whats causing it. On my machine it didn't start til Windows did the last .NET update leading me to believe that this is
the cause.
Hi,
Here’s workaround you can try:
Note: You’d better backup the registry before change it/
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SecurityProviders\SCHANNEL]
"EventLogging"=dword:00000000
Value
Description
0x0000
          Do
not log
0x0001
          Log
error messages
0x0002
          Log
warnings
0x0004
          Log
informational and success events
There’s a similar website you can refer:
http://www.eventid.net/display-eventid-36887-source-Schannel-eventno-10676-phase-1.htm
Hope that helps.
It would be nice to see what is actually causing the error rather than 'toggling it off'. Searching Google there seems to be no definitive answer, just lists of different type
fatal errors
Here's the post that I've found relating to this on TechNet:-
A fatal alert was received from the remote endpoint. The TLS protocol defined fatal alert code is 80
BTW the Forum Selection doesn't list Windows7 and that is what I have. I choose one just to post

Windows Server 2012 R2 Hyper-V VM Fileserver.
Have these errors happening consistently in event viewer every 2 to 3 minutes.
Am not running web server, just a file server.
Any ideas on how to track this down?
Not seeing much info on 36887 with code "49"
Anyone else had/solved this problem?
This topic first appeared in the Spiceworks Community

I have several recuring alarms set up on my calendar for each day of the week. In the past few weeks, an alarm will occasionaly notify me roughly 15 minutes to an hour and a half late. These daily alarms are identical and repeat every day.

I have several recuring alarms set up on iCal for each day of the week. In the past few weeks, an alarm will occasionaly notify me roughly 15 minutes to an hour and a half late. These daily alarms are identical and repeat every day and there seems to be no apparent pattern to why or when an alarm happens after the event is past.

I assume you meant iCal rather than iTunes? Yes, iCal the time zone is correct. The delayed alarms only happen sporadically. Since I posted this message, the problem stopped happening every day at the same time, but it still happens occasionally with no rhyme or reason as to when. It's gotten so that I can't depend on my iCal alarms anymore.

Error showing on the Event Viewer

Hello,
I have installed the Oracle9iAS at win2k SP3, i have this error when i reboot my server where this showing in the event viewer log.
The OracleOra9ias_homeWebCache service hung on starting.
But when i go to the services, it show this service started. But it give error on the server.
Do you have any idea to solve this problem??
Thanks
Regards,
mingjade

Hi Jordan,
Actually i can't solve that problem. So, i formated the server since is not on production yet. So it run fine now.
Thanks
Regards,
Ming Jade

Adobe Acrobat 10.1.19 crashes, Event Viewer says scan.api is at fault

Hello all,
I am a relative newcomer to these boards but I got a problem I just can't seem to find the answer to, but it is a question that others are asking as well.
I recently had to reprogram my computer, Windows 7 64-bit. I installed everything back to the way it was. I installed the Brother MFC-420CN as I always do. I installed my Acrobat 10 and upgraded to 10.1.19.
For some reason, however, the program won't let me scan.
I go:
Create
PDF from Scanner
Custom Scan
I select "TW-Brother MFC-420CN USB," click the scan button, and I get a message saying "Adobe Acrobat has stopped working."
This is what Microsoft tells me:
Problem signature:
Problem Event Name:    APPCRASH
Application Name:    Acrobat.exe
Application Version:    10.1.9.22
Application Timestamp:    52b1d7e3
Fault Module Name:    Scan.api
Fault Module Version:    10.1.9.22
Fault Module Timestamp:    52b1e4c4
Exception Code:    c0000005
Exception Offset:    00033ae7
OS Version:    6.1.7601.2.1.0.256.48
Locale ID:    1033
Additional Information 1:    0a9e
Additional Information 2:    0a9e372d3b4ad19135b953a78882e789
Additional Information 3:    0a9e
Additional Information 4:    0a9e372d3b4ad19135b953a78882e789
This is what the Event Viewer tells me:
Faulting application name: Acrobat.exe, version: 10.1.9.22, time stamp: 0x52b1d7e3
Faulting module name: Scan.api, version: 10.1.9.22, time stamp: 0x52b1e4c4
Exception code: 0xc0000005
Fault offset: 0x00033ae7
Faulting process id: 0x16cc
Faulting application start time: 0x01cf44a2b5012307
Faulting application path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\Acrobat.exe
Faulting module path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\plug_ins\Scan.api
Report Id: 299f511a-b096-11e3-b16b-1c6f6580687b
The "scan.api" seems to be the culprit but I've been unable to find a fix.
Can anyone help me?
Thanks from a perplexed but long time Acrobat user.

Unfortunately there isn't. When I install the MFC, the installation uses drivers from the 2009 installer and what it gets from Windows Downloads.

Dot is shown every day in month view, even with no events

Hi All,
With the latest iTunes update, my outlook calendar sync finally works, however, it has now decided to put a dot on every day in the month view, even on days I have no events. Outlook is still fine, so it does not appear that there is a corrupt event or anything.
Has anyone else seen this and found a fix?
Thanks in advance

Here is the fix that worked for me. I hope it helps you out.
Busy dots on every day of the month?
The iPhone calendar month view shows a dot on every day you have an event scheduled. This allows you to know, at a glance, any "free" days you have with no appointment scheduled. There seems to be a bug with some type of all-day recurring events in Outlook that sync over improperly to the iPhone. This causes the iPhone to become "confused", and show the "busy dot" on every day of the month, whether the day has an event in it or not.
In order to correct this problem, you will need to find the all-day recurring event or events (could be more than one) that are causing this. Without a search function, it takes a little bit of detective work, but it can be done.
1. Browse backwards on your calendar until you find the first day of the month with no "busy dot" in it. This will help you identify when the problem started.
2. Next, find the first instance of the problem - that is, find the first empty day that shows a "busy dot".
3. Once you find that empty day, look at the days before to find an all-day recurring event (other types of events may cause this bug, but I only experienced it with all-day recurring events, such as birthdays, anniversaries, etc.)
4. Edit the event - the start and end dates of the event should be, by definition, the same day. The bug apparently causes the event to sync over with the end date a day before the start date. This creates a situation that the iPhone calendar cannot handle properly, causing the dots to appear on every day from that point on forward. Fix the end date to be the same as the start date.
5. This should fix the problem, at least until the next all-day recurring event. In my case, I had seven events I had to fix. Every time I fixed one, the empty days on the calendar would no longer show a "busy dot", but as I browsed forward, the problem appeared again. I noticed it appeared right after one of these faulty all-day recurring events. When I fixed the event, the days from that day on forward would correct themselves until the next faulty all-day recurring event. Once all seven all-day recurring events were fixed, the "busy dot" no longer appeared on any empty days.

This warning appears in Event Viewer every day on T530 w/ Win7-64

Similar Messages

Maybe you are looking for