Three week old 3000 N200 notebook appears to be dead - will not boot up

Hi,
I bought the Lenovo 3000 N200 notebook about 3 weeks ago and have used it a few times. I was using it today on battery, when the screen went blank and it switched off (I presume the battery went flat, but I didn't see any warning). I went to plug it in, and it appeared to start up for a few seconds, I heard the fan, but then it went dead. I thought the Z symbol I could see on it meant it was sleeping, but I see now it just means power on. I cannot get the system to boot up by pressing the on/off button, function/sleep button, mouse or enter key. Nothing is responding. I have left it a few hours in case things had overheated but still nothing. Luckily, I hadn't yet thrown out my old computer so can send this message. Is there something I am not doing correctly, or is my first new computer in many years (my last couple have been second hand and have lasted for years) dead after 3 weeks?
Any help appreciated.
Thanks
gillian13au

Hi just found this in Access help which is on your laptop
Problem: The battery pack cannot be fully charged by the power-off method in the standard charge time for your computer.
Solution: The battery pack might be over-discharged. Do the following:
Turn off the computer.
Make sure that the over-discharged battery pack is in the computer.
Connect the ac adapter to the computer and let it charge.
If the battery pack cannot be fully charged in 24 hours, use a new battery pack.
Problem: Your computer shuts down before the battery status indicator shows empty, -or- Your computer operates after the battery status indicator shows empty.
Solution: Discharge and recharge the battery pack.
Problem: The operating time for a fully charged battery pack is short.
Solution: Discharge and recharge the battery pack. If your battery's operating time is still short, use a new battery pack.
Problem: The computer does not operate with a fully charged battery pack.
Solution: The surge protector in the battery pack might be active. Turn off the computer for one minute to reset the protector; then turn on the computer again.
Problem: The battery pack cannot be charged.
Solution: You cannot charge the battery when it is too hot. If the battery feels hot, remove it from the computer and allow it to cool to room temperature. After it cools, reinstall it and recharge the battery. If it still cannot be charged, have it serviced.
Hope this helps

Similar Messages

  • K8N NEO4 new old power supply died new power supply installed will not boot

    This is an old build. The K8N NEO4 powers up and is followed by a long beep. The lights on the back of the USB card (4 lights( indicate 3 greens and one red in the upper right corner. According to the instruction manual, this means that Initializing Floppy Drive Controller
    This will initialize Floppy Drive and controller. This makes no sense.
    I flashed the CMOS both using the red button and removing the motherboard battery to confirm the power supply was bad. In hindsight, I wish I had not.
    I switched from a 500W power suppply that died to a 430W thermaltake power supply. I've disconnected a hard drive and a burner to see if power was an issue, it was not the cause.
    I'm pulling my hair out here, please help!

    "Is it possible the power supply took the CPU with it when it died?"
     Yes it's possible that it did that. It's also possible that other components were killed also, that's why changing and trying different parts are required until you find everything that may have been damaged. We can only suggest what might be bad and you or someone else will need to do the actual work, there is no getting around that. We can give the serious advice, you need to do the serious labor.
    "...don't want to take the Tuniq tower 120 off if another processor will not work"
     Anybody that repairs PC's would need to swap parts to be 100% sure of what's wrong.
    Pin #20 is where -5V would be if newer PSU's still had -5V. The only the reason you would need the -5V is if you had an older K8N MB that had Creative sound on it instead of Realtek.

  • TS1718 I have purchased two complete albums in the last three weeks, old Bob Seger and new Maroone 5, both have the same issue, only a few songs will play and will skip over the rest of the songs on IPod and on computer????

    I have purchased two complete albums in the last three weeks, old Bob Seger and new Maroone 5, both have the same issue, only a few songs will play and will skip over the rest of the songs on IPod and on computer????

    Assuming you are in a region where you are allowed to redownload your past music purchases, delete the corrupt tracks from the music section of your iTunes library, close & then reopen iTunes, go to the iTunes Store home page, click the Purchased link from the Quick Links section in the right-hand column, then select Music and Not on this computer. You should find download links for your tracks there.
    While downloading select Downloads in the left-hand column and make sure Allow Simultaneous Downloads is unchecked. This seems to help with partial downloads...
    If the problem persists, or that facility is not yet available in your region, contact the iTunes Store support staff through the "Report a problem" links in your account history, or via Contact Support.
    See also:
    HT5085 - iTunes in the Cloud and iTunes Match Availability
    HT2519 - Downloading past purchases from the App Store, iBookstore, and iTunes Store
    tt2

  • My new three week old Chromebook touch pad just quit not working.

    My new three week old ChromeBook touch pad just quit working I have tried to reset or as you call it powerwash but still nothing have to use usb port mouse can you help its only two weeks old and i use it every day for school. 

    @miarose ,
    Hello and thank you for posting on the HP support forum.  If the touch pad is still not working after you have done the power wash. You will need to contact phone support for repair options.
    Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    Thank you again for posting and have a great day.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • It's less than three weeks old and the paint.s already flaking off..

    Imagine my embarassment! Here I am telling all my friends how great my new Macbook is---the high quality---and the mat finish "paint" is already flaking off to the left of the mouse pad. My God! It's like a bad used car! I may hate the Windows OS and love this MacBook but I had no idea that it had some sort of sprayed on finish. Now it looks like crap; it looks old, used and cheap.
    And it's not even three weeks old!
    Hmmm...has this happened to my three year old HP laptop? No. How about my four year old Gateway? No. Maybe my six month old Toshiba? Nope. Only my over priced MacBook.
    Now...why am I posting here? Because I can't get the lame on line service request system to accept my request for assistance in any mode.
    "Painted on quality"...worse than the blue screen of death.
    Since I can't get any support---the phone number doesn't offer a choice for my problem---maybe I should drive an hour to the nearest Apple store---and stand outside showing everyone who comes by what a seventeen day old MacBook looks like.
    Cheesy and disapointing....never again!
    MacBook   Mac OS X (10.4.8)   First Apple....Probably my last

    Listen, it really is too bad that this has reportedly happened to your new machine. I am sure that if you take it to a certified apple technician they would send it away for you to be fixed or maybe replaced. I also have dealt with APPLE CARE on the phone and they have been great, in the past. Try to phone the apple care number again and talk to a real person, forget the menu. Having said all that, I still wish that my APPLE was made in USA, even though I would have to pay more, I would.
    bm

  • HT1725 For about three weeks I haven't been able to download any apps, not even the free ones.   My apple id billing information says that my security code on the back of my credit card is invalid. I called apple support and they told me to go to the expr

    For about three weeks I haven't been able to download any apps, not even the free ones.   My apple id billing information says that my security code on the back of my credit card is invalid. I called apple support and they told me to go to the express lane website but I still cant find a fix for my problem. If you could help me out that would be superb!!!!

    Is the address on your iTunes account exactly the same (format and spacing etc) as on your credit card bill : http://support.apple.com/kb/TS1646 ? If it is then you could try what it says at the bottom of that page :
    If the issue persists, contact your credit card company and verify that they and any company they use to process credit card authorisations have the correct information on file.
    And/or try contacting iTunes support : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

  • TS1702 I have an app that appears to need to be updated. I clicked to update three days ago. It has started to update and will not finish. How can I delete the app while its in the middle of updating?

    IPhone 5
    I have an app that appeared to need to be updated. I clicked to update three days ago. It has started to update and will not finish. How can I delete the app while its in the middle of updating?

    Locked on an update can mean a couple of different things. So there are a number of things to try, but start with these.
    If you have a "waiting" icon, try tapping on the icon and see if you can pause the update/download. Of it pauses, tap on it again and see if it will resume.
    Try holding down on the icon until all of the icons on the screen wiggle. If the X to delete pops up on the waiting/stalled app -  tap the X to delete the app. Tao,the home button and the apps will stop wiggling.
    You can also try this and see if the downloads will resume. Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

  • Battery Error 601 and Notebook will not boot

    My notebook will not bootup anymore.  It was running fine then I just closed the screen and went to class.  Usually this just puts it to sleep.  When I opened it back up, it would not start...  It was totally dead.  When I plug it into the charger, I see a "Pimrary Battery Error" 601 displayed for a few seconds and then it starts to bootup.  It never fully boots-up, it shuts off totally before I get past the little HP splash.
    When I plug the charger into the notebook, I see the charging orange LED for a little while, but then it switches to white and then back to orange and then totally off.   I have tried multiple chargers and it always does the same thing.
    Since the notebook will not boot even when plugged in, I am suspecting something in the charging system/main board more than the battery.  Is there anyway to tell which components are bad?
    This is an almost 2 year old Envy 4-1215dx, Product ID: D1A99UA#ABA 
    It's been a great notebook upto now...  Any ideas on what to check and how?
    Steve

    Here's a link with an explaination and troubleshooting steps for the error you are experiencing.
    HP Battery Alert
    You can also try a Hard Reset in order to get you PC to boot long enough to run a diagnostics.
    Hard Reset
    You may also try with the battery removed and just the AC Adapter.
    If nothing seems to work you can always try a new main battery since they usually are fairly inexpensive. Just Google the Part# shown on your battery.
    If you found my answer helpful please say thanks by clicking on the Thumb's Up icon. Thanks!

  • HT1766 I am getting a message that says my iPad has not been backed up for 2 weeks and even though I click OK the message will not disppear and let me use my iPac

    I am getting a message that says my iPad has not been backed up for 2 weeks and even though I click OK the message will not disppear and let me use my iPad

    Reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

  • I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate.  Now I have no phone and I am becoming frustrating.

    I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate.  Now I have no phone and I am becoming frustrating.
    It downloaded all my contacts, photo's with no problem.  I called the number they gave me from my old phone and then turned it off.  I then put the sim card in and charged the phone.  I followed all the setup steps and no I cannot send any text or make any phone calls.  I get a message that they cannot authenticate my phone to dial #8899 but get the same message.

        Hello Notahappycamper1962
    Let's get that S5 up and running! I want you to love the S5! Is the old device powered off? What zip code are you in?
    I look forward to hearing from you and getting this addressed.
    JoeL_VZW
    Follow us on Twitter @VZWSupport

  • My Macbook will not boot the operating system.  It just goes to a blue screen after the apple logo and the spinning wheel goes off.  I took the battery out and held the on/off button for five seconds and reset the PRAM.  I have the old mac os disk.

    My macbook will not boot.  It goes to a blue screen after the logo and wheel goes off.  I have taken the battery out and held the on/off button for five seconds and reset the PRAM.  I have the the original os disk but have not put it in for fear of losing un backed op data.
    Thanks
    Rich

    You won't lose any data unless you erase your hard drive.
    Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
    If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.

  • Satellite 3000-X4 will not boot up

    The machine will not boot up even in safe mode. Is this an indication that my hard drive has failed?

    Hi Susan,
    when you try to boot your Sat3000, does the Toshiba logo appear?
    If yes, what comes then? Only a black screen with an error message or the Windows loading logo?
    When the system chrashes exactly?
    When yo want to check if your HDD is failed, create a bootdisk from www.bootdisk.info , start the Disk with a USB Floppy and try to access your HDD with typing "c:" and press enter
    If you have access you can start scandisk. This tool analyses your HDD!
    Bye

  • LR 4 - image does not appear in Preview and will not print`

    The selected image appears on the main/center panel but not in the preview screen.  Printing results in a white sheet of paper with no image at all.  The image has been updated to LR 4 - but made no difference.  I've served help and the forums (where i saw mention of similar problems, but no comments or guidance on the problem).  What am I doing wrong?

    The problem began with the installation of LR4. I print directly from LR4 to my HPZ3100. I routinely select "print preview" in the print dialogue box. Now the first print I see the preview and then it prints. If I select a second print job and use the "print preview" the print preview screen comes up blank and never loads. If I try to delete the print job, it just never responds (resolves) so I have to turn off the computer and the printer and restart to clear the print job. if I don't use the print preview, it prints just fine (except that I'm not able to check what's about to be printed). Thanks for any thoughts you have on this.
    Date: Tue, 10 Jul 2012 16:01:47 -0600
    From: [email protected]
    To: [email protected]
    Subject: LR 4 - image does not appear in Preview and will not print`
        Re: LR 4 - image does not appear in Preview and will not print`
        created by Brett N in Photoshop Lightroom - View the full discussion
    Bill, if this is only happening some of the time, then we are probably looking at a resource issue. Any pattern in when things won't print? e.g. Certain file type won't but others will? Or is it more of a timing/order thing? e.g. First file prints fine, second does not? VStromee, do no files print for you? Or is it like Bill and sometimes the print and other times they do not? Did you install any new software recently or have any updates to the OS or any application that has printing capabilities?
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4549692#4549692
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4549692#4549692. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Photoshop Lightroom by email or at Adobe Forums
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • HT1414 old iphone, bought it from a friend. it will not start, just shows a pineapple

    Old iphone, bought it from a friend. Will not start up only shows a pineapple on screen

    A pineapple? Seriously?
    It's jailbroken. You can't get help here.

  • Why does the option to watch a movie even appear if it then will not play because not downloaded? Worse, then only 23hrs left to watch!! Paying for what is not delivered!!

    ITUNES:  Why does the option to "watch movie now" appear & when chosen movie will not play because still downloading. WHY SHOULD THE OPTION APPEAR IF MOVIE CAN"T BE PLAYED. Then when movie is viewable, only 23hrs to watch! PAYING FOR MOVIES WITHOUT OPPORTUNITY TO VIEW does not make happy consumer. Emailed Itunes over and over about problem and stilll paying for services unrendered.

    When iTunes/iPod sync process failed due to timeout, the iPod, has only the initilaised  filesytem structure at the start of the Sync.
    The timeout failure could be due to
    Bad hardisk - do the iPod disk diagnostic, refer to this excellent post by tt2
    Slow USB port or resource - Dont use any USB hub, disconnect all other USB devices while syncing
    Timeout due to Antivirus or other plugins - disconnect from Internet and stop the Antivirus or monitoribng software if you are syncing.
    Preferably stop doing other things while syncing this ancient device, which the latest iTunes designer, think will soon be extinct.
    Have a nice day!

Maybe you are looking for