Time Machine Error - After Upgrade To New Hard Drive

I just upgraded from my previous 500 GB hard drive to a new 500 GB hard drive in my late 2008 unibody Macbook Pro. I have an external 500 GB hard drive that I use for my Time Machine Backups also. I used CCC to clone my original hard drive to the new internal one and everything went just fine.
I also deleted all my Time Machine backups from the external so I could just create a new one after the upgrade and cleared all the trash bins too. But now when I try and create the Time Machine backup, it gives an error that 592 GB is needed to create the initial backup, even though it is only from a 500 GB drive (of which only 440 GB) is being used. I wouldn't think this would be a possible error. Can anyone offer some help, or did I just shoot myself in the foot? Thanks.

Agreeing with Kappy, TM needs 2-3 times the size of the data it's backing-up. See #1 in the Frequently Asked Questions *User Tip,* also at the top of this forum.
The reason this backup is failing is, TM adds 20% to the estimated size of the backup when requesting space on the backup disk, for temporary workspace and in case the estimate is low. So your 440 GB will require, temporarily, 528 GB.
Short term, you can wrangle a backup by excluding something large, at least 90 GB, (so TM will only request, say, 410 GB + 82 GB for the first backup). Then remove the exclusion and run another, and it should fit.
Longer term, you really do need a larger drive.

Similar Messages

I cannot access an older time machine backup after installing an new hard drive.

After installing a new hard drive I tried to access my older backups in time machine but cannot. They are there but do not light up and allow me to access them, or select them.

First, if you're worried about the possibility of losing a backup set, then your backup strategy is inadequate. You will certainly lose those backups, no matter what you do, when the drive hosting them fails, as it will eventually. If you take data safety seriously, you should have at least two complete, independent backups of all your data, one of which is off-site at all times. I suggest you make a second backup now, before doing anything else.
The action I suggested won't delete all the snapshots; only the selected one -- unless something goes wrong, which is always possible. Without adequate backups, nothing you do is safe.

Will Time Machine with Leopard Sync With New Hard Drive and Snow Leopard?

My computer is a 20" iMac that I bought in late 2008. The hard drive had trouble so Apple repaired with disk utility. Week later, more trouble so they did full hard drive erase. Data was backed up on Time Machine, 500GB also bought in 2008. After full hard drive erase, and reinstall of basic software, upon reboot, computer would power on then immediately off. It doesn't get past white screen. They advised a new hard drive install is needed.
A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc. He could do it with Snow Leopard but I am scared. I'm afraid because my Time Machine last backup was with Leopard, not snow Leopard. I do not have my application discs with me, they are in storage in another state. Thus, if upon adding replacing hard drive and installing Snow Leopard my computer won't be able to sync FILES and APPLICATIONS from Time Machine because its on Leopard I will have a problem.
How can I either 1)Get a Leopard install disc and do that with the new hard drive install OR 2)make sure that a Snow Leopard install with new hard drive won't prevent my Time Machine from being able to install the saved FILES and APPLICATIONS if I don't have original APPLICATION (ie Aperture, Photoshop) with me? Thanks for any help you can provide.

thetrudz wrote:
A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc.
Hi, and welcome to the forums.
That Mac should have come with Leopard. If so, call AppleCare. They'll send you replacement discs for a nominal fee.
Once this is sorted out, make a 8-10 GB partition on an external HD or your internal HD, and use the Restore tab of Disk Utility to copy the Install disc to that partition. Then you can boot and run from it instead of the physical disc. It will boot and run much faster, too.
He could do it with Snow Leopard but I am scared.
If he does, and doesn't provide a retail Snow Leopard disc, you must buy one ($29). It's a violation of the license to share software, and you'll need a SL disc to do things like restore a Snow Leopard backup, or the Snow Leopard Apple apps, or repair the internal HD.
Your best bet is to stay with Leopard, at least until you have access to your 3rd-party software discs.
What you can do, however, is borrow his Snow Leopard Install disc (assuming it's a white Retail disc, not a gray one that came with his Mac), and use it to do a full system restore from your backups. That's not a violation of the license, since you don't install or use OSX from that disc; you just use the Installer utility on it to restore the Leopard OSX and all your data from your backups.
See #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum), for details.

Time machine restore-just got a new hard drive, used migration assistant to restore to time machine but cannot find files.

Sounds like i have a similar story to another user out there. 5 year old dropped my computer and hard drive was gone.
I just got a new hard drive and used Go-utilities-migration assistant to restore with time machine-- it
took several hours and seemed to be doing ok, but when done none of the files/photos/ect are available?
I did however find a back up on my Time machine labeled "sparse bundle"?
How do i get my files restored on my computer? Thanks!

Try restoring the specific files.
http://pondini.org/TM/15.html

Time Machine Restore Problem on A New Hard Drive

I am trying to restore my data from my time machine after a hard drive replacement which was done for me at my local Apple Store today. I started my Mac with the new drive and it starts like a new Mac. It then asked me during the first boot if I wanted to transfer from my time capsule which I selected. The transfer process then commenced taking 8 hours. This completed and then it took me Registration Information. This is a form which I filled in but the Continue button is greyed out even though the form is complete. The only field that I cannot enter data into is My Account (a drop down which won't provide me with any options to select). I assume the reason for the continue button being greyed out is because I cannot choose from My Account. However there is no way to select it. So I am in Limbo here. My data has been transfered but I am stuck in this process and can't Go Back (it is also greyed out). ESC doesn't work either. Any suggestions.PLEASE HELP!

Try restoring the specific files.
http://pondini.org/TM/15.html

How do I install my time machine back up on a new hard drive because the old one died?

Hi! My MacBook hard drive died, so I had a new one installed. Now, I am hoping I can transfer my Time Machine back up on it without having to do it manually. I was running Leopard on it. Can I boot from the Time Machine back up or will I have to install Leopard on it first? I'm not extremely computer savvy so , of course, I am looking for an easy way to do this! Thanks for any suggestions!

The Time Machine backup is not bootable
You will have to install Leopard first

Time Machine - Copying old Files to new Hard Drive

Need Assistance to be able to copy time machine files from one external drive to another, to allow continuation of time machine without erasing older copies, spoke to apple support, they informed me that there is a third party software (untility) that will enable you to do that, has any bod have info on this issue, Thank You

Mtaff wrote:
Need Assistance to be able to copy time machine files from one external drive to another, to allow continuation of time machine without erasing older copies, spoke to apple support, they informed me that there is a third party software (untility) that will enable you to do that
Are your files on a local disk or a Time Capsule? I was able to use a Finder drag-and-drop to copy "sparsebundle" files from one Time Capsule to another, although I had to copy them to an intermediate device and then to the final destination.
If your Time Machine files are on a directly-attached disk, you might be able to copy then with the utility SuperDuper! (exclamation point part of the name):
http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html

Trying to restore after getting a new hard drive. I can see the backup on the Time Capsule and on the correct date but it is Greyed out. That is it wont let me open it and restore the machine. Have tried also Migration Assistant, no luck.

Trying to restore after getting a new hard drive. I can see the backup on the Time Capsule and on the correct date but it is Greyed out. That is it wont let me open it and restore the machine. Have tried also Migration Assistant, no luck.

https://discussions.apple.com/thread/5210788?tstart=0
At startup hold down the Command+Option/Alt+r keys until you see a globe on the screen. Then use disk utility to partition and format the drive HSF+ and then select Reinstall Mac OS X. whatever version of OS X that originally came on your system will be installed and then you can upgrade back to Mavericks.

Setting up time machine/time capsule after fitting a New Hard Drive.

I have replaced my hard drive in my imac 24inch and restored the system from my time capsule. My question is now my time machine is trying to back up to my time capsule but it is already 3/4 full from the old drive in my imac. How do i best set up my time capsule with time machine after installing a new hard drive in the imac. I was hoping that i would restore the system and I would still be able to (after pointing time machine to my time capsule) access old files if needed in time machine. It has presently deleted a lot of older backups but still cannot fit it all in as it just sees a new hard drive worth of info and is attempting to back it all up on my time capsule.

wjosten wrote:
Me, I would never use Time Machine to do this. What I'd suggest you do is get an exterior enclosure for your new drive. Then use either Carbon Copy Cloner or SuperDuper to clone your existing drive to your new drive. Once done, verify your clone is bootable & all of your data present. Then swap drives & use your old drive for Time Machine backups(after erasing it). Then get another drive & exterior enclosure to regularly clone your new drive to.
Unless he was swapping for a lower capacity HDD or to a lower capacity SSD, then the old drive would make a lousy Time Machine disk. However, whenever I swap out a disk I do exactly what you do. CCC to get the ol drive onto a new one. Test by starting up to the new (but still external drive). Then replace the internal drive.
I usually just sell the old drive on eBay. My Time Machine backup is always 2X the size of the internal drive, which I believe is a bit above recommendations, but works for me. The price of large external drives is almost the same as smaller internal ones.

I have recently restored everything on my iMac after getting a new hard drive. When i try to use Elements, i get the following error code ERROR 150:30. Any ideas?

I have recently restored everything on my iMac after getting a new hard drive. When i try to use Elements, i get the following error code ERROR 150:30. Any ideas?

Did you use migration assistant to copy over programs, documents, and settings? You can't do that with PSE. Elements is not a tidy package in accordance with the apple developer guidelines. The installer strews stuff all of your hard drive in place the migration assistant isn't programmed to look and you can never hope to find all h the bits. You must always install PSE from scratch on a new machine. By attempting to copy it you have made a lot of trouble for yourself.
You will need to download and run this:
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
and then you can go around and manually remove what you can reach. Look in applications, your hard drive>library>application support>adobe, your username>library>preferences. In the user library also delete any saved application states for PSE.
Then you can reinstall from scratch.

If i have Time Machine backed up on an external hard drive, do i just plug the drive into another macbook pro and all my stuff is in the new computer? also, does it matter if the new computer is running Lion when the backed up info came from Snow Leopard

If i have Time Machine backed up on an external hard drive, do i just plug the drive into another macbook pro and all my stuff is in the new computer? Also, does it matter if the new computer is running Lion when the backed up info came from Snow Leopard 10.6.8?

No and Yes
Don't use TM for this purpose, clone your drive to an external, plug the external into another MBP and reboot from it. Please note that booting a machine that came with Lion may not be possible from a drive with Snow Leopard.

Time Machine not backing up other external hard drive

Hi,
I recently upgraded to Leopard and am trying to use Time Machine. I have one external hard drive that is used specifically for the Time Machine Backup, it's called "Backup Drive". The other hard drive is called "Captured Memories" and is used to store my graphic design files. Time Machine seems to backup my iMac because there is a folder called iMac and it contains the files, but the folder for Captured Memories is blank. I was getting errors saying that the backup failed but when I clicked the "Back Up Now" option on Time Machine, it doesn't list the error - but the Captured Memories folder is still blank so it didn't back up that external drive. I also changed the Spotlight preferences so that it does not search the Backup Drive.
Both the Backup Drive and the Captured Memories drives are the same, they're both Seagate Free Agent Pro drives, 1TB each.
The Free Agent Pro drives both have a sleep timer that I cannot adjust, does that have anything to do with why Time Machine won't backup the Captured Memories drive? If that is the case, what other software can I use to backup the Captured Memories external drive? I want it to sync to the Backup Drive because I am constantly saving and moving files around on the Captured Memories drive.
I was using a Memeo backup software that came with the Free Agent Pro drives but the problem I was having is it would make copies of files rather than move them. For example, I have a folder on the Captured Memories drive that is called, In Progress and one that is called In Proofing. So once a project is complete, I move the file to the In Proofing folder. The Memeo software would copy the file to the In Proofing folder rather than move it. So I'd end up with 2 copies of the file, one in the In Progress folder and one in the In Proofing folder.
Does anyone know how I can simply have the drive backed up like that?
What do I do?
Please help! I really need to make sure that the Captured Memories external drive is being backed up!

I am having a similar problem. I initially set it up 3 days ago and had it back up just the iMac to Time Capsule (about 120 GB) which it did no problem (I initially had my LaCie drive excluded). I then un-excluded my other drive, where all my photos and music reside (about 130 GB). Since then, it keeps trying to back up about 102 GB each time. Looking at the list of backups it does not appear that it has ever successfully backed up the LaCie. I am not aware of any error messages, but I have not been home much. I normally shut down the computer at night but I have been leaving it on trying to let Time Machine do its thing. All I can say is that every time I am at the computer TM is running and it always looks like it is in the middle of backing up 102 GB (usually seems to be near the beginning, never seem to see it more than halfway done). Looking at the TM panel it says the latest backup was 2 days ago. I'd appreciate any advice!

What to do after installing a new hard drive on inspiron 1525

after installing a new hard drive on my inspiron 1525 I place the drivevers and utilities driver on the cd/dvd player drive, chose boot from cd/dvd drive, and I get this message
your cd/dvd drive during this boot cycle is f:
a RAMDISK drive is available for this boot cycle as C:
it contains several hard drive setup tools. Please use these tools only under the direction of dell support staff.
F:\>
What do i enter after F:\> ?????????
<ADMIN NOTE : Email Id removed per Privacy policy>

Hello Warren,
To understand the issue and help you further, I would request you to help me with few details about the issue.
-- What exactly is happening when you turn on the computer?
-- Do you see a black screen with a blinking cursor?
-- What is the Operating System?
-- What is the System Model?
Run a hardware diagnostics to check if there is any hardware failure.
-- Restart the computer.
-- Keep tapping F12 key on the Dell Logo screen.
-- From One Time Boot Menu, select Diagnostics and press Enter.
-- If the test fails please capture the Error Code and write back to us would be glad to assist with the next course of action.

I just had to reformat the external hard drive that houses my iPhoto library, then restore it from a backup. Now Time Machine is telling me my backup hard drive suddenly does not have the space to complete a backup. I also noticed when I go in to Time Mac

I just had to reformat the external hard drive that houses my iPhoto library, then restore it from a backup. Now Time Machine is telling me my backup hard drive suddenly does not have the space to complete a backup. I also noticed when I go in to Time Machine, there are only about 5 backups recorded on the ext. hard drive. There were many more before. Any idea what happened and if I have to buy a new back up hard drive?

Hallo Kieth ,
I am not quite ready to restore the full iphoto library , as I have days of work re - imputting titles,descriptions and enhancement . I hope that your suggestion works , as I use my Macbook basically to work with digital photography. Through time , I will need to delete my library to recover more disc space and I would hate to have to spend more time re - imputting titles and descriptions all over again .
Thanks for your interest and advice.
regards - Alan

I have a time machine backup file on a USB hard drive. I bought a time capsule / airport extreme, flat 3TB. I wish to transfer the backup file from the usb hard drive to the time capsule hard drive. 10.6.8

I have a time machine backup file on a USB hard drive. I bought a time capsule / airport extreme, flat 3TB. I wish to transfer the backup file from the usb hard drive to the time capsule hard drive. 10.6.8

Unfortunately, Time Machine backups that are stored on a drive that has been connected directly to a Mac are completely different than Time Machine backups that are stored on a Time Capsule.
Frankly, it is not worth the effort and trouble to try to transfer the old backups to the new Time Capsule.....my opinion....having done this in the past.
It is possible though, but I would not recommend it due to the complexity and downsides involved with this. To give you an idea of how to do this, check out this support article.
http://pondini.org/TM/18.html
Even if you transfer the "old" backups over to the Time Capsule successfully, Time Machine will not simply "add on" to the old backups.
Time Machine will make a new complete backup of your Mac and then add incremental backups from that point.
My advice.....start a new backup on the Time Capsule and move forward. Keep the USB hard drive around for a month, maybe 2 or 3 in case you need to go back to an old backup for some reason. At that time, you will not likely need the old backups at all since you will have a current 2-3 month history of new backups. At that point, you can erase the USB drive and use it for another purpose.

Time Machine Error - After Upgrade To New Hard Drive

Similar Messages

Maybe you are looking for