TMS Provisioning Extension services: BASE GROUP Configuration Issue

I was trying to configure the TMS Provisioning Extension services and i got stuck in Base Group Value?
Error was getting something like the Base group value which i given was wrong. And it's asking me to check with TMS Administrator. Unfortunatly i am the one who configured the TMS also. but i didn't find something like Base Group value.
In my scenario i have two VCS Control, two VCS Expressway, and a TMS. I have the clustering configured on both VCS Control and Expressway. and i need to use TMS Provisioning Extension Service for Cisco Movi.
Where i can find the Base Group Configuration value?
Regards,
Nikhil Jayan

Hi, i am not able to see the Provisioning Mode option in Administrative tools > Configuration > General Settings.
Administrative tools > Configuration > Provisioning Extension Settings tab also is not coming. I am using TMS Version 13.2 and VCS x7.1.
Do i need to configure something to get enable the TMS Provisioning Extension Service on TMS.
Please help me.
Regards,
Nikhil Jayan

Similar Messages

TMS Provisioning Extension Service won't start

Hello,
Recently our TMS Provisioning Extension Service has failed to start. When trying to restart the service we get the following error ...
TMS Provisioning Extension service terminated with service-specific error 1 ( 0x1). Nothing has changed on the server so not sure what the issue could be?

Hi Andy,
is this problem resolved?
if not, what version of TMS and TMSPE are you running?
what version windows server and SQL server are you running?
have you checked the windows eventlog messages? what do they say?
regards, Ahmad

Failed to enable TMS provisioning Extension

hi, ciscomen!
     just trying use tms provisioning extension for movi register
    Cisco TelePresence Management Suite Provisioning Extension Deployment Guide
    http://www.cisco.com/en/US/docs/telepresence/infrastructure/tmspe/install_guide/Cisco_TMSPE_Deployment_Guide_1-0_with_14-1.pdf
   after installed TMSPE on tms server , the system got some notes and alarms and the vcs provisioning mode is "tms anent legacy “mode but
   can not switched to "provisioning" mode
the system log:
"To enable the VCS to import provisioning data from TMS, the VCS Provisioning Mode must be set to 'Provisioning Extension'.
Configure the connection settings and the individual services first and when the status of all the services are OK, the mode can be switched to 'Provisioning Extension'
what should i do??
need your help

Hi, i am not able to see the Provisioning Mode option in Administrative tools > Configuration > General Settings.
Administrative tools > Configuration > Provisioning Extension Settings tab also is not coming. I am using TMS Version 13.2 and VCS x7.1.
Do i need to configure something to get enable the TMS Provisioning Extension Service on TMS.
Please help me.
Regards,
Nikhil Jayan

TMS Provisioning Extension not working

I've come into a new environment with my new job and noticed that the TMS server has TMSPE installed, but when going to TMS general settings, I don't see the right dropdown. I only get Enable Cisco TMS Agents.
I am on TMS 13.2 (looking to upgrade to the latest)
VCS is on X7.1
VCS is throwing TMSPE alarms all over the place.
Base Group is not populated.

Look over this guide, can you confirm what version of TMS you're using? Looking at the Cisco TMSPE Deployment Guide 1.0, on pg 20 "Enabling Cisco TMSPE", it shows a different screenshot then what you've provided. You show "Enable Cisco TMS Agents" in your screenshot, however the guide says "Provisioning Mode".
The most current versions are TMS 14.5 and TMSPE 1.3, see Cisco TMSPE with VCS Deployment Guide 1.3 on how to upgrade your deployment.

Adobe Document Service Configuration Issue

Hi All,
Actually we have installed SAP ADS 7.4 ON SAP NetWeaver 7.4 JAVA STACK HUB
SYSTEM.
I did the configuration as per the SAP Standard documents. The ABAP
connection in ADS is working but ADS configuration in an ABAP environment
is not working.
While I am executing the form in SFP, I am getting the error message:
ADS:com.adobe.ProcessingException: com.adobe.Processin(200101).
While I am testing the ADS configuration in ABAP environment, I am getting the error:
ADS: com.adobe.ProcessingException:com.adobe.Processin(200101).
While I am checking the Destination service in SAP ECC I am getting theerror: SYSTEM ERROR:
ADS: com.adobe.ProcessingException:com.adobe.ProcessingException: XMLFM Exception during render:com.adobe.ProcessingException(200,101).
For the above issues I raised ticket to SAP. They suggested below steps, So I did the first three steps but I don't know how to do the 4th and 5th steps means how to copy the and extract the files.
1. Shutdown J2EE engine
2. Rename the folder
/usr/sap/<SID>/<Instance>/j2ee/os_libs/adssap
to antoher folder name (ex. adssap.old)
3. Start J2EE engine
4. Make sure XMLFormService_native.zip is copied under os_libs fold
during starting up engine (synchronize phase)
5. Also make sure XMLform.exe is extracted under
/usr/sap/<SID>/<Instance>/j2ee/os_libs/adssap/XMLFormService/bin
Please help me from where to copy the zip file mentioned in 4th step and find the attachments for error screen shots for reference.
Your help will be appreciated.
Thanks&Regards,
Ravikiran.

Hi Varun,
Actually we installed ADS in NW 7.4 and while I am doing configuration I am getting the above issues.
While I am executing the any form means (standard also) I am getting the same issues.So I think it is may be configuration issue.
I raised ticket to SAP with the below error they suggested above five steps.
ADS: com.adobe.ProcessingException: com.adobe.Processin(200101).
Thanks&Regards,
Ravikiran.

Hi, I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mail are not receiving. Mail queue showing Connection refused error. Please help me

I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mails are not receiving. Mail queue showing Connection refused error. Please help me
Thanks
GIRI

Try this -> http://support.apple.com/kb/TA38632?viewlocale=en_US

Cisco Provisioning Manager 2.1 bulk service area detailed configuring

Hi folks,
I'm really stuck and need some help desperately.
I have bought Cisco Provisioning Manager 2.1 for 5000 handsets and I have isntalled the product ok however I am now at the stage where I need to configure the service areas. I have some 45 sites which equates to about 350 service areas.
Service Area for each site with the following differences:
- Odd Device, Present CLI
- Even Device, Present CLI
- Odd Device, Restrict CLI
- Even Device, Restrict CLI
Can someone please advise me a way to bulk configure these detailed attributes with some tool or a let me know of a customer northbound API application that has been written to do make this painful exercise much less painful?
I estimate its going to take me 5 weeks full time to click through each thing and configure it..
Please help!
Cheers
Beau

You can bulk load (with batch provisioning) the Service Areas... I did this by exporting my phones into a CSV file from Communications Manager, and then filtered it for the fields required for the SAs. Then you just follow the instructions for batch provisioning that start here: http://www.cisco.com/en/US/customer/docs/net_mgmt/cisco_unified_provisioning_manager/2.1/user/guide/infrstct.html#wp1051558
I hope that helps...
--Joe

An error occurred while trying to provision the service 'Discussions'.

Hi All
I initially got the error Failed to authenticate user when accessing the discussion and Announcement services within WebCenter. I subsequently configured WS Security by providing the required keystore as indicated in this tutorial:
http://e20tricks.blogspot.com/2010/02/webcenter-quick-install-guide.html
I've created a orcladmin user that is the system admin in Jive Forum too and use this as the required user in the service configuration within EM.
I now however even though the Discussion and Announcement Service is available in WebCenter get the following error when trying to add either service to a group space:
An error occurred while trying to provision the service 'Announcements'. The service did not get provisioned.
I can't find anything in the logs that indicates any errors.
Have I missed something? A slight configuration stuff-up perhaps?
FYI my keystore defines -dname as "cn=machine name, dc=com, dc=au".
Any advice and help would be much appreciated :)

Make sure when you generate your keystore you use these commands:
genkeypair
importcert
exportcert
and not:
genkey
import
export
if the above commands you should be using are not available you've got an issue with your keytool which is probably an incorrect java. Make sure you have a JDK installed.

Error checking transport group configuration in System BQS

Hi Everyone,
I made a client export from Production to Quality. It went successfully,, I noted the requests numbers and transported them from PRD to Quality, but while transporting there was a tp error(which i did not note), next i went to the quality import queue and saw all the 3 requests had come. But when i click the adjust queue icon im getting the following error message "Error checking transport group configuration in System BQS" . Afterwards i tried to delete the requests from quality to retransport from production but still im not able to delete those requests from quality. Can anyone help me solve this.
Regards,
Rahul

Hello Rahul,
regarding the error message:
"Error checking transport group configuration in system"
It's mostly related to the TMSADM RFC destination. Kindly follow the below mention steps:
1. Logon to client 000 with user DDIC.
2. STMS > System > Overview > Select the system in which you are logged in > Click on the menu says EXTRAS > Generate RFC Destinations
Perform the above steps in all the systems configure in your TMS. This should resolve the issue.
Best regards,
Tomas Black

Network: Unknown / The dependency service or group failed to start

Hello, MicroSoft tech crew. I know my issue is not something new to you, there are earlier posts with similar to identical problems to mine. For a whole day I tried everything I could find on the internet to fix my issue, but nothing seemed to work.
I cannot connect to the internet. My network and sharing center displays the following, instead of the map:
Unknown
The dependency service or group failed to start.
I am running windows 7 Professional 64-bit.
I used ESET NOD32 as antivirus. I uninstalled it the day this issue appeared.
I have no restore point.
Any other computer or device can successfully connect to my router.
Re-installing a fresh copy of windows is not an option.
These are the solutions I tried and didn't work:
I tried restarting the router (1 minute power-off)
I HAVE reinstalled my drivers for both LAN and WAN network cards at least twice each.
~ I ran the following commands in CMD as administrator over 3 times, successfully, followed by reboot:
* sfc /scannow
* netsh winsock reset // netsh winsock reset catalog
* netsh int ip reset // netsh int ip reset reset.log hit
I have checked the following in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\servicel\NlaSvc has always had full control and read permissions for both SYSTEM and Administrators.
I replaced my nlasvc.dll file from C:\Windows\System32\ with one from another computer (and set TrustedInstaller as its owner)
Booting in Safe mode with networking does not change this situation.
These are some of my services. Note that I turned some of those from Manual to Automatic.
1) COM+ Event System
* Automatic, Started
2) Computer browser
* Automatic, Started
3) DHCP Client
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the DHCP Client Service on Local Computer."
"Error 1186: Element not found."
* Dependencies:
3.1) Network Store Interface Service
* Automatic, Started
4) DNS Client
* Automatic, started
5) Network Connections
* Automatic, Started
6) Network Location Awareness
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Network Location Awareness service on Local Computer."
"Error 1068: The dependency service or group failed to start"
* Dependencies:
6.1) Network Store Interface Service
* Automatic, Started
6.2) Remote Procedure Call (and all it depends on)
* Automatic, Started
7) Remote Procedure Call (RPC)
* As stated above: Automatic, Started
8) Server
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Server service on Local Computer."
"Error 50: The request is not supported."
* Dependencies:
8.1) Security Accounts Manager (and the RPC)
* Automatic, Started
9) TCP/IP Netbios helper
* Automatic, Started
10) Wireless Zero Configuration (XP)
* Nonexistent
11) WLAN AutoConfig
* Automatic, Started
12) Workstation
* Automatic, Started
Also, my ipconfig /all looks very strange. I am not allowed to post pictures yet, but this is the image on skydrive server:
/#cid=2168FA597AC0EAF1&id=2168FA597AC0EAF1%21107

I follow your solution and found the
Network Location Awareness service
could not start.
Then I found the solution from:
http://mjmcfalls.wordpress.com/2012/04/07/network-location-awareness-service-terminated-with-service-specific-error-1073741288/
by running the commands:
net localgroup administrators localservice /add
net localgroup administrators networkservice /add
to add the "Localservice" user and "NetworkService" user
to the adminstrators group.
And the problem solved after reboot.

Essbase 11.1.2.1 Configuration Issue

Hi ,
I am using windows xp 32 bit processor and installed Essbase 11.1.2.1 successfully.
Configured with one Oracle 11g data base user/Schema working fine and also tried to configure with Two Users/Schemas
in another system workig fine.I heard that if we configure only with one schema Essbase components and Shared
services will conflict.so I would like to know with how many users we have to configure only Hyperion Essbase to get
Better Performance.
Regards
Sekhar.

Hi John,
Then shall i proceed with one user/schema ?
If i proceed with two users/schema is there any problem will come or not ?
Is there any order to configure with one schema ?
like all Foundation components first after Essbase components.
Number of schema/users consideration is not an issue to me but i need best configured
Essbase Server without facing configuration issues in Future.
I had doubt on it may expect clarification ?
Regards
Sekhar

CUCM Group Configuration- question about phones failing to secondary callmanager

I wanted to get clarification about how exactly phones will register to the secondary or tertiary servers if the link to the primary fails.
I have a 3 server CUCM cluster. 1 subscriber that some phones register to is separated from the other 2.
When the link to that sub goes down, the phone should then register to the secondary server of its Cisco Unified CallManager Group configuration, correct?
If this is true, then my next question is how long does it take to then failover to the secondary server?
SRST is not involved in this, it's just the CUCM Group Config. Any help clarifying how phones behave in this situation?

I found my own answer in the Cisco Press Troubleshooting Cisco IP Telephony book, page 155:
"The TFTP configuration file received by the IP phone has a list of up to three CallManagers
for registration purposes. The order of CallManagers indicates their priority. The first is the
highest-priority CallManager for the IP phone. It is the first place the IP phone attempts to
register. The highest-priority CallManager is also called the primary CallManager.
When the IP phone registers with its primary CallManager, it also establishes a standby
TCP connection to the next-highest–priority available CallManager, sometimes called the
standby CallManager, secondary CallManager, or backup CallManager.
The IP phone knows that there is an alternative CallManager for quick failover if it loses connectivity
with its primary CallManager.
At any given point in time, the CallManager to which the phone is registered is its active
connection. The CallManager node that has a standby TCP connection for the IP phone is
the standby connection.
Failover occurs under two conditions:
• If the TCP connection between the IP phone and the primary CallManager goes down.
Incidentally, stopping the CallManager service on a server causes all the TCP connections
to be closed and all the IP phones on that server to register to their standby.
• If CallManager has not responded to three consecutive KeepAlive messages sent from
the IP phone.
Any number of network-related issues could cause the TCP connection to go down. When
the IP phone registers with its standby CallManager, it registers with an alarm indicating
why it failed over.
Under the second condition, CallManager fails to respond to three consecutive KeepAlives.
The IP phone sends a KeepAlive message every 30 seconds by default. CallManager should
answer each KeepAlive the IP phone sends with an acknowledgment message. If
CallManager fails to respond to three consecutive KeepAlive messages, the IP phone marks
the connection as “bad.” The IP phone does not tear down the TCP connection, but it does
not attempt to re-register with the “bad” CallManager either. It continues sending
KeepAlive messages to the “bad” CallManager until CallManager tears down the TCP
connection. This delay gives CallManager time to respond if it recovers quickly. After 10
minutes, the IP phone removes the “bad” tag and again tries to establish communication
with CallManager using KeepAlive messages in the process just described. During this
time, the IP phone attempts to establish a connection with its secondary CallManager (or
its tertiary if the secondary is not available) and registers if possible.
If a call is in progress when an IP phone detects the loss of a TCP connection, the IP phone
does not fail over until the call is finished. If CallManager fails to respond to three consecutive
KeepAlive messages while an IP phone has an active call, the IP phone again waits
until the call is finished before registering to its standby CallManager."
Hope that helps someone else in the future.

Provisioning users to AD groups in OIM 11gR2

I could use some advice on how to resolve this issue I am having.
Using the Active Directory connector (11.1.1.5) in our OIM 11gR2 development environment I can successfully provision OIM users to our AD resource. I have successfully run the org and group lookup recons, and provisioned users do go into the correction ou in AD.
However when I select which groups a user should be a member of in the ADUSERC child form (via the lookup), the user is not provisioned with the correct group membership in AD.
A separate issue is how to map the objectClass in AD in the ProvAttrMap; could anyone point me in the direction of how to go about that?
Thanks

The ObjectClass should be configured in this lookup Lookup.Configuration.ActiveDirectory
Check below
http://docs.oracle.com/cd/E22999_01/doc.111/e20347/extnd_func.htm#sthref221
4.6 Configuring the Connector for User-Defined Object Classes

What is base line configuration and final configuration

Hi
1. what is base line configuration and what is final configuration?
2.Can we calculate depreciation every day , if yes how plz explain?
3. what is the Organizational structure in FI , CO , and over all FICO and in Asset Accounting?
for 3rd one , in 1 interview for FI org structure i answered
CLIENT-COMPANY-COMPANY CODE- BUSINESS AREA
but the interviewer not satisfied, i checked in SAP LIBRARY there is also same,
if my ans is not correct plz tell me the correct org. structure,
and for Asset a/c ing in sap library 2 possible org structures r there 1 is
CLIENT-Chart of a/cs - Charf of Depre-Plant -B.area,
is it correct ,
plz can one answer for my doubts
thanks
thanks in advance

for your action............don,t confuse the structure....
1.FI Orgination Structure:
Client>Controlling Area>Company code>Plant->Storage Location--->Finished goods or Raw material
(ii)Co.code>Sales Org.>Distribution Channel-->Division
(iii)Co.code>Purchase Org>Product group
(iv)Co.code--> Business Area
2.AA Orgination Structure: Client> Chart of Depreciation>Depreciation Areas>Asset Classes->Company Code->Main Asset> Sub-asset.
3.CO Orgination Structure:Client>Controlling Area>Cost center or Internal Order or PCA or Produt Costing
Client/Operating Concern --> Co-PA

HFM 11.1.2.3 Configuration - Issue with Consolidation Administration

Hi,
This is regarding a new/fresh installation EPM 11.1.2.3 and have an issue with configuration on HFM; the deployment is distributed as below
1) Server 1 : Foundation,WebLogic Admin(/OHS) - Workspace/Shared Services/Planning/Calc Manager/EAS/APS
2) Server 2: Essbase
3) Server 3 : EPMA/HSF/HFM(FDMee/DRM-Yet, to be installed and configured) - Hadnt used these products and this is totally new to me.
We have issues with HFM - and while opening the Consolidation Administration.
We get an error as below, in workspace
An unexpected error has occured.Check server log or contact your system administrator for more information.
The web app logs suggested below errors- This is only part of the error log
E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\HFMWeb0\logs\oracle-adf.log
Part of log
oracle.adf.model.adapter.DataControlFactoryImpl] [SRC_METHOD: createSession] Exception: [[
oracle.adf.model.adapter.AdapterException: DCA-29000: Unexpected exception caught: oracle.epm.fm.common.exception.HFMException, msg=There is no registered cluster or server
I hadnt configured 'Configure Cluster' during the HFM configuration; this was a mistake being new to HFM.
On a further readup online on OTN etc, found that an application cluster is a must have on HFM, even if it is for one server.
Have one confusion now for fixing this,
Do a configuration only for 'Configure Cluster', and restart services to fix this issue
or
Do a configuration for 'Configure Cluster'and then again re-Configure HFM components
Configure > Financial Management — Configure Cluster
Re-Configure > Financial Management — Configure Application Server
Re-Configure > Financial Management — Configure Web Server
Re-Configure > Financial Management — Configure Web Application
Re-Configure > Financial Management — Enable Smart View Provider
Re-Configure > Financial Management — Enable Life Cycle Management Provider
Re-Configure > Financial Management — Enable Web Services

Got help from Oracle Support, and this problem is now resolved. The HFM app server was configured fine, earlier.
Had to follow below steps on the EPM configurator.
Stop Services
HFM - Configure Cluster
HFM - Configure Web Server
HFM - Deploy to App Server
Foundation - Configure Web Server.
Start Services
Refresh workspace

TMS Provisioning Extension services: BASE GROUP Configuration Issue

Similar Messages

Maybe you are looking for