Touchsmart 600 1390 - issue after upgrade to Windows 8 - DVDBD wont work.

I successfully upgraded to Windows 8 and although the harddisk ran non stop for about a week, with me dubbing 8 - WindowsWait... It eventually finished whatever it thought it was doing and is about normal now.
EXCEPT the DVDBD that is onboard now can not read any media. I have uninstalled and reinstalled the Windows driver several times but without any resolution. I have searched the HP website but there is nothing i have found there - drivers or advice.
Any ideas?

Hello,
You have used the drive to install windows right? Was the unit working before you have done the upgrade?
Optical drives should not give any problem after an upgrade, other components you might not get a driver due to manufacturer not releasing it, but not the optical drive...
Make sure you have your windows activated and you have all windows updates already installed...
How is the optical drive detected in windows explorer and device manager? Can you tell me how the drive is detected?
Thanks,
I work for HP! Please remember to provide and if this helped click ON

Similar Messages

Networking Issues after Upgrading to Windows 8.1

I have a Windows 8 desktop PC that is working fine with my network. I can browse the Internet fine using all major browsers etc. After upgrading to Windows 8.1 through the Windows Store I noticed that my wired networking was not working correctly.
The status of the network does not change (i.e. it doesn't change to Limited Connectivity) however browsing to sites in Chrome, IE or Firefox doesn't work as well as Windows 8.
IE11 gives me the error "This page can't be displayed, make sure the web address is correct" and other browsers give a similar error. I normally have to refresh 2-3 times to get a new page to load, sometimes even more. Everything works
fine from a laptop connected at the same time so it isn't an network issue with my provider.
I thought this might be a driver issue with the two on-board Marvell wired network adapters. I wasn't able to rollback the driver to older versions I found on the Internet. I then purchased another network card, Intel Desktop gigabit and the
issue still persists with that adapter. I then tried a USB wireless adapter and the issue still persists using wifi with the wired adapters disabled. I tried a new network cable and no luck either. I also tried resetting the IP stack using
the various netsh commands.
After that I thought I might try reset the Windows 8.1 PC, however that didn't work as I didn't have the restore image available as I upgraded from the Windows Store. I then tried installing Windows 8.1 fresh using a ISO with my Windows 8 key using
some of the recent guides that are available. That all worked but it didn't fix the networking issues.
I re-installed Windows 8.0 and the networking is now fixed and back to working normal again. I'd like to try again but I think I will have the same problems. I can't imagine why this would be a driver issue as I tried 3 different network adapters
and two installs of Windows 8.1. Any ideas what would be the cause of the Windows 8.1 issue?

HI,
Since this issue only occurred in the your desktop PC, and many network adapters you tried, failed, thus I think maybe we should focus on the model of your desktop PC, I suggest you update the BIOS and chipset from the manufacture to improve
the performance of win8.1.
Please also test this issue in safe mode with networking.
Please refer to:
Windows Startup Settings (including safe mode)
http://windows.microsoft.com/en-in/windows-8/windows-startup-settings-including-safe-mode
I’d like to share the following article with you:
Wired and wireless network problems
http://windows.microsoft.com/en-IN/windows/network-connection-problem-help#network-problems=windows-81&v1h=win81tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1
Regards,
Yolanda
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.
The issue occurs in safe mode as well under Windows 8.1. The motherboard is an Asus P5B Premium, however it works on Windows 8. How would I update the chipset when booted into Windows 8.1? In Device Manager it wasn't allowing me to update
the network drivers as they were newer versions already installed.
Edit: I also installed at Intel Chipset Device software dated 8/8/2013 with version 9.4.0.1026 and the issue still occurs. I am also running the latest BIOS that is available.

U410 touch WiFi issues after upgrading to windows 8.1

Hi all,
I have a U410 touch and yesterday I upgraded to windows 8.1
I have major WiFi issues.
connection drops after a few minutes giving limited. troblesshooting resets the adapter saying ''the default gateway is not accessible '' is fixed. But after a few minutes the problem comes back. and it goes like this forever.
I have the Intel Centrino N-2230 and I installed the driver I found here (15.10.3.2).
I''ve tried to uncheck the power management option but the problem is still there.
I also have other issues with the dolby system (I see others have the same problem )and my touch screen is not working.
any help will be greatly appreciated
thanks!

Hi-
I am also running into the same issue with my Lenovo U410 and it is really frustrating. I also have Centrino Wireless chip with driver version 15.10.3.2 and I have windows 8.1
I bought the laptop from Costco and was having similar issues. I sent it back to Costco Concierge who apparently replaced the wireless chipset on this laptop but now I am getting this issue.
Any help will be greatly appreciated.

[Forum FAQ] SkyDrive synchronization issue after upgrading to Windows 8.1

After Windows 8.1 released, users may encounter the issues about syncing files in SkyDrive. There are the error messages you may find:
Error 0xS00705B4: This operation returned because the timeout period expired
Sorry, the action couldn't be completed because the file hasn't finished uploading. Try again later
Error 80070490: element is not found.
Many SkyDrive folders in library like SkyDrive [1], SkyDrive [2] …
We just would like to point out some possible causes of this issue and give you some suggestions to troubleshoot it.
Cause:
Location was messed up during upgrade.
Pending uploading or downloading task blocked in synchronization.
SkyDrive was hang.
GPO blocked the syncing behavior
The user profile folder was relocated after upgrading.
How to fix:
Suggestions 1: Checking the consistence of locations on both registry key and SkyDrive properties:
Right click SkyDrive -> Properties -> Location tab
Open regedit.exe, locate to the following key and check the location.
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\SkyDrive
Suggestion 2: For many SkyDrive
folders:
Check which one can be explored properly with right files and relocate the SkyDrive folder via changing the settings in
suggestion 1.
Or create a new folder for relocating SkyDrive’s.
Suggestion 3: End the Skydrive.exe process and restart in command or disconnect and reconnect your MS account in SkyDrive to clear the pending task:
Press Win+R to open run, and type following commands one by one:
%windir%\system32\skydrive.exe /shutdown
%windir%\system32\skydrive.exe
Log off your MS account in SkyDrive and log in again to check the issue.
Suggestion 4: Check the GPO settings in both gpedit.msc and regedit.exe:
In GPO: If User Configuration –> Administrative Templates
–> Desktop -> Prohibit User from manually redirecting Profile Folders
is enabled, please disable it. Don’t forget to force update the policy changes: run command
gpupdate /force as admin.
In regedit: if DisablePersonalDirChange is set to 1 under
HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer, please change it to 0 and start the SkyDrive to check the results.
At the end, we can’t assure that these suggestions can fix all such
issues. If you need further help, it’s ok to feedback here or submit a new thread with the
SkyDrive.exe.err.**.log under C:\Users\[Your name]\AppData\Local\Microsoft\SkyDrive\logs
uploaded for research.

I wrote a blog post back in January which describes a similar issue with the SkyDrive / OneDrive app in Windows 8.1 and how to resolve it at
http://richardjgreen.net/roaming-profiles-windows-8-1-skydrive-app/.
Hope this helps somebody.
Richard Green | MCSA 2012, MCSE 2003, MCTS Desktop Virtualization, VCP5-DV http://richardjgreen.net

Heating, Longer Startup issues after upgrading to Windows 8.1

It has just been about 1.5 years I have purchased this laptop and the way it is behaving now is killing me.
There was absolutely no problem while I was running Windows 8(which was my preloaded OS).
But after I upgraded to Windows 8.1 I am facing numerous problems which I am stating below.
Startup time has increased to double the time it took perviously( even after I disabled unnecessary startup entries ).
Laptop is getting heated from the moment it is started, no matter what I do or I do nothing and keep it idle(which earlier happened only when I played any high graphics game)
HP Support Assistant no longer works in Windows 8.1(I uninstalled and reinstalled it several times still no solution), so I am no longer able to get any technical support.
Right click on Desktop takes ~10 seconds to open up the menu(Once again checked and found no unwanted third party context meny handler entry blocking the right click)
Please help me out as soon as possible.
Currently I am using Microsoft Windows 8.1 x64 Single OS
Product Name-HP Pavilion G6-2236TX NB PC
Product Number-D4B09PA

Hey @cDeepanjan ,
Here is what is happening with the error message 303. Hard Disk 1 Quick Test Failure-If your notebook is under warranty, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link to get the support number for your region. They will be happy to assist you immediately.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Sleep and Shutdown issues after upgrading to Windows 10

Hi there,So I'm having issues with sleep and shutdown after I upgraded to Windows 10, the laptop won't go to sleep or shutdown properly. The screen turns off, but the power LED stays on and the fan as well. If I chose sleep it won't wake up no matter what I try, and I'd have to perform a hard shutdown everytime.Any solution for this problem?Thanks.

**I have posted this in another area with the same issue** YES!!!!! A Solution that worked. Spread the news. It has to do with the Intel Virtualization Tehnology. Didn't know what that was until this issue came up in Windows 10. First, find out if this is your issue. 1. I installed the 'Intel Processor Identification Utility' directly from Intel.2. After installation, open the program and go to the 'CPU Technologies' tab.3. If it says 'YES' for Intel Virtualization Tehnology, proceed. Solution...(at least on my system) 1. The next thing you have to do is go into the BIOS. If you have not done this before, proceed at your own risk. You need to restart the computer and enter the BIOS (for me I hit F10 at the HP screen)2. Within the BIOS, there is an 'Advanced Options' section3. In this section there is a line for 'Intel Virtualization Tehnology' and it will say enabled or disabled. My computer said disabled.4. If this is the case, change the option to 'ENABLED'; then SAVE and EXIT from the BIOS. The Computer will restart and from that point on Shut Down, Sleep, etc. has worked. WOW this was a frustrating issue. Almost went back to Windos 8. I take no credit for this solution, I pieced it together from other posts on this issue. Hope this helps.

Split x2 - Touchpad issue after upgrading to Windows 8.1

Hello,
I bought this Split x 2 a week ago and it came with WIndows 8. Everything was working fine until I upgraded to WIndows 8.1. Now my Touchpad will freeze some times and I have to log out and log back in to my profile to unfreeze the touchpad other times I can get it to unfreeze by resetting the release touch screen buttom.
I called HP customer service and they said it was a Microsoft issue and transfer me to them. Microsoft said it was a hardware (HP) Issue and that i needed to go back to the store where I bought it
(BestBuy). I took it back yesterday to BestBuy and they gave me a knew one. I did the same thing and upgraded to Windows 8.1 and touchpad issues is back. So pretty sure is not a hardware issue.
All windows updates are completed
I checked the Touchpad's Driver and it is up to date.
NOTE: I plugged a wireless mouse to my laptop and when the touchpad freezes the wireless mouse still works.
Does anyone know a fix for this issue? Everything else works great on the laptop is just very inconvenient when you are working and you have to log out to get your touchpat to work again.
Any help would be appreaciate it.
Jhon C
This question was solved.
View Solution.

Well you gave me a great idea. So the same thing happened to me, the install failed due to the driver signature. I uninstalled the current driver, then turned off the feature that requires signed drivers and installed the driver. Everything is working so far.... the only odd thing is it doesn't show the driver any where. I am going to try a few other things BUT the mouse hasn't stopped working for a good half hour.
http://www.howtogeek.com/167723/how-to-disable-driver-signature-verification-on-64-bit-windows-8.1-s... Incase you didn't know.

Bluetooth issue after upgrading from windows 8.1 to windows 10

i upgraded from windows 8.1 to windows 10 , The experience was really nice and windows 10 work beautifully of my system. But the only thing is i am not able to find Bluetooth in my system. May be some driver issue. I have troubleshooted many times but the problem as not been solved . So any one can please help me on this.

On Sun, 1 Feb 2015 10:34:40 +0000, Field Commander A9 wrote:
In-place upgrading from Windows 8.1 to Windows 10 will cause all desktop internet browsers to be unable to open any non-local web pages. You'll have to use netsh to reset the winsock stack to fix this.
Not necessarily. I've upgraded several systems here, ranging from tablets
to laptops to virtual machines with a combination of IE, Chrome, and
FireFox and I've not experienced this on a single system. Also, your post
is the first time I've seen this issue reported in the forums.
Paul Adare - FIM CM MVP
The problem with the gene pool is that there is no lifeguard. -- BSD
fortune
Nah, the problem is that it doesn't have enough chlorine. -- Lionel in ASR
It also lacks an undertow for the weak ones. -- Joe Creighton in ASR

G60 laptop left without sound and bad screen issues after upgrading to Windows 8

I have a G60-458dx notebook that I just recently upgraded to windows 8.
Since then I have had no audio whatsoever, and anytime I try to wake the computer from sleep or hibernation, the screen won't turn on. To get the screen back I have to do a forced shut-down, then turn it back on.
I've tried uninstalling/reinstalling all of the relevant drivers (e.g. video, audio, chipset) to no avail. If anyone has any info on available generic drivers that would work, or updates from hp, you would make me a very happy man.
Here are the hardware id's for my audio and video.
HDAUDIO\FUNC_01&VEN_14F1&DEV_5051
PCI\VEN_8086&DEV_2A42

Try uninstalling the audio driver and installing this generic IDT audio driver: http://goo.gl/0IMBd
If that does not resolve your audio issue, then more than likely it is a hardware compatibility issue.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Portege M700 rotation issues after upgrading to Windows 7 64 bit

I upgraded to windows 7 last night on my portege m700. It is Windows 7 Pro 64 bit. I installed all the drivers under the Windows & 64 bit category on Toshiba's page. Everything works great except the screen will not properly rotate when put into tablet mode. I can push ctrl+alt+ arrow keys to rotate it, and I can also use windows mobility center to rotate 90 degrees at one time. I am wondering what I need to have it rotate once snapped into tablet mode, like it did in Vista. I have the Toshiba rotation utility installed but it doesn't seem to be doing anything. It seems like it is not receiving a signal from the monitor that it has been rotated.
I need this for school, so any help is GREATLY appreciated.

Hi
I think there are not all Win 7 64boit drivers published and released for M700 and you will have to install also some drivers released for Vista 64bit!
For example:
*Tablet PC Extension Package v 1.0.0.1 for Vista 64bit*
This driver package installs a range of important utilities.
_TOSHIBA Rotation Utility:_ Set the default screen orientation you want the system to use when switching from PC to Tablet mode, or vice-versa.
_TOSHIBA Tablet PC Buttons Driver:_ You can dedicate tablet buttons to performing common tasks so that you can easily operate your tablet computer when you're away from your workstation. For example, you can dedicate a button to open a program or to change your screen orientation.
_TOSHIBA Accelerometer Utilities:_ These Utilities are a set of hardware utilities that work with the motion sensors built into you machine. With the Accelerometer, your machine will be able to detect the way you are holding it at any given moment. You can set the machine to perform a specific function when the unit is quickly tilted to the left or right, or to the front or back. You can also take control of the cursor in some applications and make it move by leaning the PC in a certain direction.

Pavilion DV4 : After upgrade to Windows 7, fingerprint doesnt work

Hi,
I upgraded to windows 7 yesterday using HP Windows upgrade kit.
Everything is working fine except for Digital Persona. It say reader not connected. I had downloaded it from HP site.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-72110-1&lc=en&dlc=en&cc=in&...
However, If i download the demo application from validityInc, that works fine (it detects the reader)
What should i do to make this digital persona work?
Regards
Ajay

Hi all
Thank you for your post: I will be elated to assist you!
Is your windows 7, 32 bit or 64 bit? The link provided above, is for 32 bit. Here is a link to the HP software and driver page for your computer click here. This has all of HP's software and drivers for this model. I am sending you a link to "Downloading and Updating Software and Drivers for HP Computers" click here.
You can try running MS Fix it click here, aid in this endeavor. I hope this is helpful.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Acer Aspire V7-582PG very slow after upgrade to Windows 10 - ExpressCache not working

Upgrade my Acer Aspire V7-582PG to Windows 10. Startup and main windows events are very slow. The caching SSD is not used at all. I checked and I noticed that the ExpressCache software is removed during the upgrade to Windows 10. The folder "C:\Program Files\Condusiv Technologies\" is empty and the background service is gone. Tried to reïnstall an old version of the ExpressCache software (1.0.94), but Windows 10 is actively blocking this software and won't let me install this. Anyone have this working? Or contacted Acer Support about this problem?

Hi IronFly Thanks for your assistance, sadly this is one of the earlier solutions I have tried, however - still not working. ExpressCache does install with this particular installer - however, running 'ECCmd.exe -info' in admin command prompt gives me a result: Microsoft Windows [Version 10.0.10240]
(c) 2015 Microsoft Corporation. All rights reserved.C:\Windows\system32>eccmd.exe -info
ExpressCache Command Version 1.0.98.0
Copyright® 2010-2012 Condusiv Technologies.
Date Time: 8/4/2015 18:21:20:278 (REDACTED-PC #0)ExpressCache Driver is not installed.
**ERROR** ECCmd exited with error 0x1 (1) Really starting to struggle with this now. As I see it I need the following programmes installed to go ahead: IRST (Intel Rapid Storage Technology)ExpressCacheIntel Rapid Start Technology It seems Acer have dropped the ball on this one, with other manufactures already aware of the issue, and providing solutions. Acer do not seem to be aware, I have submitted a support ticket here in the UK, and I am really hoping I have missed something and they have a fix or workaround already. This is quite poor on Acer's part - I have always enjoyed their products, and been loyal to Acer, however this is starting to make me question whether they are just a tech vendor rather than LTS provider too!

Lenovo driver issues after upgrade to Windows 10

Hi, i recently upgraded my Y50 to windows 10 after i got the notification. Now the Fn+F6 to disable the trackpad and Fn+F5 for airplane mode don't work. others seem to be working properly. I was unable to find any rivers. Also, i noticed that league of legends now runs at 60fps when uncapped, while previously it ran at about 180. I am not sure if the nvidia graphics card is being detected or if it is using the intel one.

the problem has been fixed by 1- reinstalled win 10 2- win 10 removed intel hd 5500 driver as expected , but i didnt update it manually nor by update from device manager nor make any changes , so i ran windows 10 update tool from system and made all 100% update after restart things are ok now every thing is ok and new intel hd 5500 driver has been installed by win 10 update tool : 10.18.15.4248 //driver date : 29/06/2015 also invidia 840m driver has been updated thanx for any try to help and if any one still stuck with black screen the problem is that win 10 read two monitors instead of 1 so you have to click "windows button + P while black screen already on " and try to hit and click on first choise or other choises till you can see the desktop , sure u cant see any thing while u are trying to choose but you should try or may be you connect another monitor or tv and fix this issue by win button + P good luck

HP Officejet Pro 8500 all-in-one printer - issues after upgrading to Windows 8.1

After successfully downloading a driver from the HP website to enable using this all-in-one printer with a new HP laptop using a Windows 8.1 OS, I confirmed that the printing function works normally (just as it did with a Windows XP OS on my wireless home network).
However, I don't find any icons appearing on the 8.1 desktop for other HP apps (e.g. HP Solution Center, HP Photo Creations). I do have an icon for the Printer. When opened, it shows two options: 1) add a new printer and 2) add new software (from the original CD). But the original CD is for the XP OS, which I don't try and possibly mess up what already is working.
So-o-o, Is there any HP software download available for HP apps to use with this printer, especially HP Solutions Center?

Hi Riley.
You can get HP Photo Creations here:
www.hp.com/go/hppc
It's a free download for Mac and Windows.
Hope this helps,
RocketLife
RocketLife, developer of HP Photo Creations
» Visit the HP Photo Creations Facebook page — news, tips, and inspiration
» See the HP Photo Creations video tours — cool tips in under 2 minutes
» Contact Customer Support — get answers from the experts

UE4 demos not running due to dependency issues after upgraded from Windows 7 x64 to Windows 8.1 Pro x64

Hi, I posted a more in detail thread about this on the UE4 forums.
https://answers.unrealengine.com/questions/84890/dependency-issues-with-running-ue4-demos.html

Hi,
Are you using a Gmail account on both Outlook PC client and on the phone? Is it an IMAP account?
Since you mentioned it also occurs to your phone, have you tried to logon the Gmail webmail to check the account status? If new emails sent to the account don't show up on the phone, it's not isolated to Outlook then, we need to contact the Gmail support
to get this issue addressed.
For the emails missing issue, I suggest you just open the .pst file instead of importing it. In Outlook 2013, go to FILE tab -> Open & Export -> Open Outlook Data File -> Browse to the .pst file and open it. It should then be displayed
in the account list on left. Check if the emails are still missing.
If you can confirm you included the emails in 2014 but they are still nowhere in sight, they may be filtered by the Outlook View. Run Outlook with the switch "/cleanviews" to check whether the emails are shown:
Press Win + R, type "outlook.exe /cleanviews" in the blank box, press Enter. Outlook will reset default view, all custom views will be lost.
Let me know if you have further questions.
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Touchsmart 600 1390 - issue after upgrade to Windows 8 - DVDBD wont work.

Similar Messages

Maybe you are looking for