Trigger cycle count when zero qty is picked

I need help with the following issue.
Currently when the user confirms a TO with LM05 and selects confirm with differences (and enters zero qty picked) the system cancels the TO but no additional steps are taken to ensure that the cycle count team knows of the inventory variance ..
How can we trigger a cycle count in this instance when we are confirming with differences and Qty picked is 0.
Can someone please outline the steps needed in config.

Ah, I see you dont even have a problem with cycle count, you just do not know how to enter the scrap quantity during the daily work.
It depends, as everything in SAP, on the process were the scrap material appears.
If it appears as a by-product in while you produce something, then the quantity is created with movement type 532
But if you create this scrap if a worker damages soemthig, then you issue the damaged material with 201 to a cost center, and then you do a 202 movement to create stock at a scrap material master.

Similar Messages

How does Mac OS calculate the charging Cycle count?

Hello, Guys
How does Mac OS calculate the charging Cycle count? I just used my MBP for about 15 min without power plugged in and I saw it left about 90% battery. However after the battery be recharged, I checked system profiler. It shows charging cycle count increased 1. I do remember that last time I left almost the same percentage of battery and plugged in. After the battery was fully charged, profiler did show cycle count increased.
So I am wondering How does Mac OS calculate the charging Cycle count? Basing on the percentage left or something else?
Thanks,

Ok,
But does it count continuously or separatly? I mean One time I used 10% and recharged full; and next time I used 20% and fully recharged again. Does the OS increase the cycle count when the usage adds up to 100% no matter how many times of recharge?
Thanks,

"New" computer comes with battery stating 2nd cycle count?

Returned one MBP 15" because of defect and was given a new sealed version of the same unit. When looking at power I noticed that the battery is on 2 cycle count. This unit is having some problems as well, but I saw the gentleman in the store here in Paris cut the seal on the unit, as well as the unit being sealed within its wrapping in the box. Why would a new computer be on it's second cycle count when never used?
Thanks

Shaggywerewolf wrote:
It probably got cycled once right after being manufactured for testing. Similar reasoning why you won't find a brand new car with 0 miles on the odometer.
Correct.
I wouldn't worry unless it had more then, say, ten cycles. Anything less then that is acceptable.

How setup cycle counts with wms picking

How setup cycle counts to dispatch tasks when make picking of an order with wms and activate an exception?

Hi,
We need to use customization with respect to your requirement as you cannot meet the whole requirement with seeded parameters available in Picking rules. Let me know your mail id so that i can farward you an document that is from oracle which suggests about the using the functions and packages in the picking rules.
Regards,
Sravan.

How do I get a 0 to display when a count = 0 (zero)? (The cell is blank)...

(Running Business Objects Release 2 (Web-I), No other reporting modules)
How do I get a 0 to display when a count = 0 (zero)? (The cell is blank)...
In my reports, I count the number of tests of one of our products and another count on the number of failures. I then use a simple formula to give me the defect rate percentage (DR%)
The universe objects used in the calculation are:
Assembly Number (dimension)
Human Sn (dimension)
Test Code Description (dimension)
I created a variable (called [Count Assys]) that counts the number of Assemblies Tested:
Formula: =Count([Assembly Number];All)
Another variable (called [Failed Count]) counts the number of failed tests:
Formula: =Count([Test Code Description];All) Where ([Test Code Description] <> "FUNCTIONAL TESTS PASSED")
NOTE: There is a "not equal to sign" between [Test Code Description] and "FUNCTIONAL..." above, but the forum is blanking it when I preview the message. Not a big deal, but it may be important for someone looking to help...
I then have a third variable called [DR%] that divides [Failed Count] into the number of [Count Assys], which yields a number formatted as a percentage.
Formula: =[Failed Count]/[Count Assys]
The above works great!
The problem is: when I have a zero defect count (everything passes), the cell is blank, so the percentage variable remains blank. I want a zero (0) to appear if nothing failed so the percentage appears as 0%
I've searched this forum completely and have tried several Properties changes and different variable strings (like =If([Failed Count]<1,0) and the cell stays blank and cannot come up with an answer.
This one seems simple to me, but everything I've tried has yielded zero <smile> results.
Thanks,
Charles
Edited by: Charles Norman on Dec 9, 2008 12:44 PM
Edited by: Charles Norman on Dec 9, 2008 12:47 PM

Hi Charles,
Use [Dr%] Variable formula as =if(IsNull([Dr%]);0;[DR%])
Here IsNull returns the Boolean value of variable [Dr%] if its true then inserts 0 else the percentage values of failed tests based on the total number of assembly tests performed.
I Hope this is what you want to achieve....
Thanks....
Pratik

Cycle Count Reservation Issue in Item Supply/Demand Form

Hi
Few of the inventory items are stuck with Cycle Count Reservation in Item Supply/Demand Form. The Identifier field is empty. It is not tied to any sales order or PO . I checked the On hand quantity(on-hand quantity form) and the current on hand (Item Supply/Demand form) both are same. Could not able to figureout what went wrong and how the cycle count reservations are created. Even after performing the Cycle counting on these items, it did not consumed these reservations and releaved those reservations.
Could anyone suggest me please in what scenrios we get this issue and how to eliminate these records from the Item Supply/Demand Form. we are on 11.5.10.2 INV and WMS RUP4.
Thank You!
Krishna

CC reservations can be triggered by Curtail (Short) picks on mobile gun. When this happens the ATR qty gets decremented by this Qty by putting a CC reservation.
This can also be deleted from front end by changing the demand source to acc/acc alias, save and then delete.
Karthik

Triggering Cycle count

Dear Experts,
Are there options in Standard SAP to trigger automatic cycle count/ physical inventory records when i do picking with differences or put away with differences?
This way say after the worker who picked with differences will move on and do his job, because the system has an inventory record document created, an inventory person can follow up on the document & and go to the location to check the situation of the bin.

issue closed.

What does the field Inconsistent mean for ABC Analysis for Cycle Counting report

What does column "Inconsistent" mean for report ABC Analysis for Cycle Counting (T-code MIBC)? The reason I'm asking is because I see TotalStock values greater than 0, but the Accounting 1 view for Material Master and MMBE both show zero stock. I do not understand why TotalStock in the report does not show zero. Can anyone explain how this can happen?
Note: the report is run for consumption/usage date range.
Thank you,
Doug

Hi,
MBEW table and MMBE transaction will show the current stock. When you run MIBC report for consumption, the system considers the consumption for the date range given (from MVER table), which may not be equal to the current stock. Refer the KBA: 1817237 - Stock quantities and stock values in MIBC which explains the system design.
Regards,
AKPT

How does cycle count recommendation works.

I setup my cycle count codes as well as assigning them to the item master, when I run cycle count recommendations there are lots of items need to be counted. Here are my questions
1.     Where do I go to enter the new counts?
2.     When I enter the count do I enter the difference or what I counted?
3.     When Do I flag the items counted on cycle count recommendation screen?
4.     When I am doing cycle counting some transactions could take place at the same time how does system takes care of that so I do not over count or under count?
5.     Can I get a report of all items which I flagged as counted regardless of qty on hand or not? I need this data for cycle count analysis.
I have the documentation from SAP but I cannot see these steps.
Thank You

Your question is too long. One question for one thread. This is forum rule. Although it can still belong to one big question, it is better spitted to more.
For first 2 questions:
1. Where do I go to enter the new counts?
Go to: Inventory -> Inventory Transactions -> Initial Quantities, Inventory Tracking & Inventory Posting
2. When I enter the count do I enter the difference or what I counted?
Enter what your counted.
Thanks,
Gordon

Cycle Counting - New on SAP

We are new on sap. So most of our materials have never been counted. I have run mibc(ABC analysis), then I ran micn by material group to generate a cycle count. One of my 'A' materials is missing. It's in stock and we've never counted it before. Shouldn't everything that hasn't been counted come up on my cycle count? If I extend my cycle count date out, it comes up, but it's not due until 6/1/2009 to be counted.
Any help would be appreciated.
Thanks

1. What was the planned count date range that did not show the one A material and the range that did?
I originally ran the count for 5/6/2009 - the A item was not included
When I extended my date range to 5/6/2009 to 8/30/2009, the item was included, however it wasn't due to count until 6/1/2009, and it was being placed on a physical inventory count sheet for that future date.
2. What other checks and values are you using in MICN?
Selection Criteria:
plant - 3020
Storage Location - 0001
Material Group - KIDD
materials marked for deletion - checked
Stock Level:
materials w/o zero stock -checked
Data in Phys Inv Doc Header:
Date 5/6/2009
Batch Input Session:
Issue Log - checked
Name of Session - MB_MI01_CN
Max. No. of Items - 333
Sort by:
Material Group - checked
Enter grouping criterion in doc header - checked
What is the stock level of this material?
52 unrestricted
I did find also that the consultant that configured our cycle counts made an error. The A items are set to count 2 times a year. But would that make a difference? I thought everything that wasn't counted and was in stock for that material group would show up.

Cycle count listing Report not generating out put

Hi Team ,
We are into 11.5.10.2 , We have set Auto schedule to weekly in cycle counts and cycle count is not generating output for cycle count listing in Production.
But, we are able to generate report output in Test instance and unable to generate in Production . We tried testing with same login in Production and Test Instance .
Please advice
Thanks
Kiran

Also please confirm that the CC calendar and other CC related setups are exactly same from the PROD and TEST instances.
Also make sure that you are running the report for the same INV org.. as there is no Input parameter for the Org in the report input but it picks from the MFG_ORG_ID profile value, which gets assigned when you loginto the responsibility.. You can confirm the selection by Chane Instance Org and select the Inv org and then run the report..

Freexing movements during WM cycle count

Hi Gurus
strange issue we are facing -
When we start the Cycle count in WM , it freezes the creation of TR, TO for all the materials for which Phisical invetory document is active , But in case the Sales Order having 4 items and physical inventory is active only for 2 parts , its does allow the delivery for those other 2 parts as well.
Could some one help me if there is something config missing , or solution How Can we freeze the delivery for tht part if there is a physical document active for one of the part in Sales order..
thanks in advance..Points will be rewarded for helpful answers
BR

Hi
Thanks for reply...
I agree tht system should pick the 2 items for delivery for which cycle count is not initiated ..but as I mentioned I have 4 items on Sales Order , cycle count is initiated for 2 of them.. but with the physical invertory document active for these 2 ..
system is aloowing to make delivery for all four items..which I dont see is correct..
is there any option to restrict the delivery ..only for the sales order items for which cycle count is active..
could you pl send me some guidelines..
BR

MIE1 :: Sale order cycle count issue

Dear All,
II am using transaction MIE1 to create inventory documents for sales order stock. I am receiving many more items to count than expected. I checked the cycle count indicator and materials coded to be counted only once a year and last counted in February and March in table MSKA, but still when i executer IME1 system is picking it for cycle count.
We are on SAP 4.67. Our fiscal year ended at the end of September.
Anyone know why these materials would show as due to count now?
Thanks,
Chaithru

Hi Terry,
To be honest there is not normally any standard manipulation of the bin sequence in Physical Inventory, but here are a few places to look here (Grab a coffee first)
Logistics > Warehouse Management > Strategies > Define Sort Sequence for Putaway >
Logistics > Warehouse Management > Strategies > Define Sort Sequence for Removal >
These two items determine the sort order priorty of your bin numbers, eg. if your bin numbers are 10 digits long, you could sort the bins in order using key co-ordinates with differing priority. So the second character of your bin could be sorted prior to the first character. (The logic here will be based upon the individual warehouse layout/rules)
Next have a look in
Logistics > Warehouse Management > Activities > Transfers > Processing Performance > Profiles (Have a look at Sort profile)
Logistics > Warehouse Management > Activities > Transfers > Processing Performance > Control for Performance Data Processing / Define TO Split
In these two you can manipulate the sort order of the bin numbers in TO and other documents, can look complex but is simple when you have understood the logic
Good luck
Steve

Cycle count Storage location selection

Hi,
Could someone explain to how the Storage locations are selected when I run transaction MICN.
Our settings in config are like this
I have a material in one storage location, it has never been counted. I run the transaction MICN for that material in my plant with today's date nothing is returned. I change the date to one year in the future and the system returns many locations including the one the material is in. I can comprehend that because the count date is empty in the mard table, I have to enter a future date but why do I get many location where the material is not even stored in?
By the way as we only want to count all our items once per year, they have all been set with the letter D in the material master.
Kind Regards
Thierry

Where do you see the advantage of cycle counting if all your materials are classified with D?
In that case you can just use MI31 and do annual inventory.
If you have no last count date, then SAP uses the creation date if the accounting view.
Which is for all materials equal if you loaded them before go-live.
And the storage location is coming from MARD table, all locations for which your material was created. And because you did not activate the box to exclude the materials with zero stock.

Cycle count Process - T code MI04

Hi all,
I am having a doubt in cycle count process.
I have created some CC document using MI01. When I go to MI04 to enter actual count; I could see that some of the line itmes are non editable. One observation is that; column ZC (Zero count) against non editable material is set as clicked.
what does it mean to have ZC (Zero count)indicator clicked.
also even there are some material in same documents for which available quantity in SAP is zero; still they are editable and ZC indicator is not marked.
kindly guide.
regards,
Parshuram

Someone must have entered the ZC.
Quantity field cannot contain 0. SAP does not consider it as an entry. Hence if you find that there is no stock for an item, you select ZC (to signify 0 stock) since you cannot enter 0 in quantity.
Hope this answers,
Lakshman

Trigger cycle count when zero qty is picked

Similar Messages

Maybe you are looking for