Trouble getting 1130AG LWAPP to Connect to Controller
I'm having trouble getting any of my 1130AG LWAPPs to connect to my WLC.
I have not configured my DHCP server to deliver option 43 or option 60.
However, I have manually configured the LWAPP using the CLI. I have assigned a static IP address, the default-gateway, gave it a hostname, and gave it the controller ip address.
When I issue the command:
show lwapp ip config
all of the information appears correctly.
However, the controller never registers the LWAPP.
This is a completely new setup, so there are no previous configs to contend with.
If I issue the command on the LWAPP:
debug lwapp client event
Two debug messages appear consistently every 3-5 seconds. They are:
*Mar 1 00:34:26.733: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 1 00:34:36.733: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR
Any suggestions?
~ Vance R. Gregory
You have to put option 43 in hexadecimal no. below you will find an example of DHCP configurations on router that act as a DHCP for LWAPP in different network:
ip dhcp excluded-address 172.16.1.1 192.168.1.1
ip dhcp pool WAP_DHCP_SCOPE
network 192.168.1.0 255.255.255.0
option 43 hex f104c0a814f0
The hex string is assembled by concatenating the TLV values shown below:
Type + Length + Value
Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
WLC IP is 192.168.20.240 f1+1*4+ac10.14f0 = f104c0a814f0
default-router 192.168.1.1
Similar Messages
-
hi all
im having trouble getting my laptop to connect to my mac using migration assistant. my mac has a code on the screen but my laptop doesnt respond and just says it waitng for my mac to respond.
any idea? pleaseHi Christina, belated welcome to Apple Discussions if nobody said it already.
I've had some experiences with these new flash memory recording camcorders, and I'll give you a quick rundown of what I've learned. Many of them (JVC, Panasonic, etc.) tend to record in a .MOD file format, which is non-standard, proprietary, and unrecognizable by most software. I thought Canon was usually a little more standards-compliant, but it appears they also use this .MOD format in your specific camera model. There are likely a couple ways we can get around this though!
In order to play the files, you will likely need to change their file format (.MOD) to .AVI manually. You'll have to locate the files on your Mac, and then manually change the file names so that the file extension (after the period) is .AVI
At that point, a video player application such as http://www.videolan.org/vlc/download-macosx.html>VLC should play the files fine!
You should be able to transfer new video files from the camera to the Macbook Pro with no problems as well. Just plug in the camera to the computer via USB, and also make sure the camera is plugged in to charge. Once it's plugged in, open iMovie (came with the MBP, in the Applications folder) and the MBP should take care of the rest.
Let me know if you have any success with any of this!
FYI, the thread that I got some of the above information from is here:
http://forums.macrumors.com/showthread.php?t=478326
--Travis -
Trouble getting my phone line connected
My saga to date....
I contacted BT on 20th April to advise them that I was moving home on 29th April (to a newly built house). An engineer was arranged to come to my home on 10th May to carry out the connection. Prior to the 10th May, I had a visit from an engineer to assess the job. My house has been built in an older part of a village which still relies on telephone poles and lines going from the poles in to houses. During one of these visits, it was noted that I would need a pole placed in my garden to connect the line to, then the line would be connected from there. The reason behind this was due to the fact that my house is built low down, and to take a wire straight from the main pole would make it slope too low. I was quite happy with the solution put forward, and was happy that things seemed to be in hand. At no point was I told that the work would not go ahead on the 10th May.
This is when the problems start.......
I feel that I am living in the dark ages again. I have no phone line, hence no Internet access and do not get a mobile signal in the area I now live in! I rely on travelling to my daughters' house to use their phone and Internet access, which is not convenient.
The 10th of May came and went, and nobody appeared at the house, and I received no communication that work would not be carried out on this date. I phoned BT, and yes, I was talking to a call centre in India. When the operator finally grasped the issue that the engineer had not appeared she checked with her suppliers to inform me that there was a problem and that this would be assessed by the 14th May. BT would then advise me on the 15th what the next stage would be. Unhappy with this, I was eventually put through to the supervisor (waited 40 minutes on hold!). Got no joy from him, but the promise he would personally contact me on 15th. I had to accept this and hung up.
On Monday 13th May, I went online to check the progress of my order, only to note that my latest BT bill was ready. When I checked the bill, I noted that BT had started to bill me for my phone and broadband package from 10th May!. Blood pressure steadily rising, I contacted BTs billing department, yes once again an Indian call centre, to complain. Got the standard script from the operator - very sorry etc. During this conversation, it was realised that BT had the wrong postcode in for my house (it was the correct street, but the post code for odd numbered houses). The operator, against my pleas not to do so, cancelled my order, and set up a new order for the correct postcode. She assured me that she knew what she was doing and not to worry, everything would be fine (I had explained the saga to date to her). She set up a brand new account, allocating a different phone number, and requiring me to set up new direct debits - I'm not sure how she couldn't just change the postcode for my original account. A new connection appointment was for 21st May, and I was assured that there would be no problems I would be connected on this date.
The 15th of May came and went, and no phone call from the Indian call centre manager. I did not call back at this time, as a new appointment had been scheduled.
The 21st came, and an engineer did appear - hooray! He looked at the house and told me - I cannot do your connection. A pole is needed to run a the line to. He was able to tell me that my number had been set up in the exchange. I was more than a little angry and frustrated at this point. BT knew that a pole was required back on 6th May - why had this information not been dealt with!
Again I phoned BT, back to the Indian call centre. Explained the whole saga. He checked with his 'suppliers' to find out what was going on. Came back to tell me that further information would be available the next day. I was getting a little annoyed at the point. I explained that the work required was to erect a pole in my garden to run the line to. All I wanted was a date for when this work would be carried out. He could not give me this info saying his suppliers would not give this until the next day. I asked who the suppliers were - BT Open Reach, but he would not let me speak to them directly. He promised to phone me back the following day with the update - probably to get me off the phone. I again explained that I had no means to which he could contact me in my own home, and would require to go to my daughters house to receive the call. He agreed to phone me back at 10am on 22nd May - a time when I would go to my daughters. Yes, once again they failed to phone back!!
I again phoned back - yes back to India I went. Asked to speak with the manager - but the operator would not connect me saying he could help. Went through the saga once more - again got the text book apologies (which are getting rather annoying now). He contacted the 'suppliers' and promised that contact would be made with me within 24hours by the engineer with regards to the work being carried out. I told him that I had been lied to on so many occasions that I didn't believe that this was the case and asked to speak to BT Openreach to confirm this. He stated that this could not be done. Trust him, why would he lie to me - which I told him would be to get me off the phone. I left my daughters phone number as a contact.
24hours has now passed, and yes - once again no contact. I cannot face talking to another operator in an Indian call centre who will tell me anything to get off the phone. BT's complaints procedure is pathetic. I feel totally helpless in this. There doesn't seem to be any communication between anyone in the company. The call centre staff are telling you anything just to get rid of you. I suspect that I am now being billed on 2 accounts for a service I don't have, and no doubt will be another saga when I eventually get a working phone line.
I am no further forward to when this work will be getting carried out, and getting more and more frustrated. Is there any suggestions on where / who I can go to.
Solved!
Go to Solution.Hi
I am sorry to see you are having problems
I suggest you contact the forum mods they should be able to get this problem sorted for you this is a link to them http://bt.custhelp.com/app/contact_email/c/4951
They normally reply by email or phone directly to you within 3 working days they will take personal ownership of your problem until resolved and will keep you informed of progress
They are a UK based BT specialist team who have a good record at getting problems solved
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’ -
First time on here and my knowledge with networking and such is very limited, my Mac Pro can connect to the router but when I try to open my browser it wont bring up any webpage. The only way I can get internet is through an ethernet port, Im basically at a loss for what to do.
You will find the AirPort icon (looks like this ) on the OS X menu bar. Option (or right) click the icon, and you should be greeted with a drop-down menu. All of the parameters I mentioned should now appear after the name of your Wi-Fi network.
The meaning of each of the values are as follows:
PHY Mode = The radio mode that your Mac Pro is connecting with.
Channel = The radio channel the Mac Pro is connected to.
RSSI = Received Signal Strength Indication. It's an indication of the power level of the signal as preceived by the Mac Pro's internal Wi-Fi antenna. Typically the higher the RSSI number the stronger the signal. RSSI is measured in arbitrary units. Some manufacterers use a positive scale, others like Apple, use a negative (0 to -100) instead. For the AirPorts, the less negative the better.
Transmit Rate = Instantaneous maximum date transfer rate of the connection in Mbps (Megabits per second)
MCX Index = Modulation and Coding Scheme. The MCS value identifies a number of things, including the number of spatial streams used in the Wi-Fi connection between the Mac Pro and the AirPort router. A larger or smaller MCS value is meaningless. Instead, it defines the actual connection type. In turn, the type can play a significantly on the potential bandwidth performance. -
Trouble getting PM G4 to connect to Airport Express over Ethernet
I was wondering if folks could give me some guidance on how to get my PowerMac G4 (older model with NO airport card) to pull an IP address from an Airport Express. I have the Powermac G4 and Airport Express in one area of my house. The Airport Express is setup as WDS remote on channel 1. I have an Airport Extreme Base Station in another area (setup as WDS main on channel 1) which is connected to my DHCP-enabled Linksys router. Both the Extreme and Express units are set in bridging mode. I was hoping the PM G4 (which is connected to the Airport Express via an Ethernet cable) would pull the IP address off the network (I have the G4 set for DHCP) but so far it is only pulling a bad IP address - not within the range that the Linksys router should be providing.
Any suggestions?A Mac computer or laptop.....with a sophisticated operating system.....will automatically connect to the wireless access point with the best signal quality based on its location in relation to the device producing the wireless signal.
So, if you move the Mac from one area to another, it will automatically "switch" to pick up the stronger wireless signal from the closest wireless access point.
Other devices....with simplified wireless software.....usually will not do this...and instead will tend to always connect to the first device with which they originally connected.
If you want a device to connect to a specific wireless access point, you might want to try deleting the current wireless connection on the device, moving it very close to the AirPort Express, and then configuring the device to connect to the wireless network again.
With luck, the device will now pick up the stronger signal from the AriPort Express. But, if it does, it will probably stay locked onto the AirPort Express if you then move the device back closer to the AirPort Extreme. -
Can't get older mac to connect to wireless router
I have an older G4 mac, which had an Airport wireless snow type of router. I've currently upgrade to an iMac with an Airport Extreme router. I can't get the old G4 to 'see' the Airport Extreme Network, so I can use the other computer to check email and get on the internet. Do I have to load in the same Airport software on both machines? Any help will be appreciated.
On my G4, I have the software installed which I used when setting up my other wireless router, the snow M8440. Could this be the problem?
Yes. Let's take a step back. You can use any computer to configure your new Airport Extreme, but first be sure you have installed the Airport Utility program from the link I posted above. The earlier version of Airport Utility you used for your Snow Airport doesn't have the necessary features to configure your new Airport Extreme.
The only reason to keep the old Airport Utility program would be to configure your old Snow Airport Base Station, which you're not using any more. So put it aside.
Since you're having trouble getting your G4 to connect at all, it makes sense to use your new iMac to configure your new AirPort Extreme. So let's use it for now.
The ability to use the dual band feature of the new Extreme is described starting on page 20 of the following: Apple Airport Networks (early 2009). The document is very lengthy but don't let that bother you - Apple's Airport base stations are extremely versatile and the manual gets very detailed, but most of it won't concern you.
I made a wireless network named Airport Extreme on my iMac.
The way you worded this concerned me, so at the risk of sounding Presidential, "let me be clear"
Technically, you don't want to create a wireless network on your iMac - the wireless network with which you want to connect is created by your Extreme, and you use Airport Utility to make that happen.
Your Airport icons on all your computers should look like one of these:
If it looks like this:
then you have created a "computer to computer network". You don't want that.
Next: the passage of the Apple Airport Networks manual above also describes how to set up your Airport Network's wireless security...
I click on the Airport Extreme, the next window comes up with Wireless Security: WEP password. I type in my password I used to set up the Airport Extreme network, and get the following error message: There was an error joining the Airport network "Airport Extreme". ...
I advocate using no security at first, to eliminate one roadblock when first configuring a network. After everything works, set up WPA or WPA2 Personal. I'm reasonably sure your G4 supports it. The older WEP protocol is no longer considered secure - it amounts to "feel-good" security.
I trust this gets things pointed in the right direction. If you're still stuck write back and we'll get you un-stuck. Your G4 will work with your new Extreme. -
I'm now having trouble getting mac mail to work on my mac. The mobile me account works great on iphone and ipad but it won't connect to my mail account. Password is correct. What else can I do? Using OS10.68
HI,
The Apple IDs from @mac.com and @me.com (Older MobileMe and more recent iCloud Names) are also Valid AIM Screen names.
Any other sort of Apple ID is not a Valid AIM Name.
A Google ID that is associated with Google Mail Account (And has "Talk" enable on your Google Settings) can be used in iChat as Jabber Name/ID. (Google Run Jabber server).
Jabber and AIM are different IM Services and it is not easy or straight forward to add Buddies from one Service to the Buddy List of another. (As A Starting point consider it "impossible")
iChat 4 and 5 have links to the registration page of @Mac.com here with a "Get an iChat Account" button in the add (Account) screen (You select @mac.com or MobileMe and then press the Button - Choosing AIM and then pressing the button used to lead to the AIM registration page but AIM moved their page).
Apple IDs can be any valid email (or an @mac.com or iCloud registration)
Therefore you could make a Google ID into an Apple ID.
However this will not be a valid AIM Screen Name the way @mac.com or MobileMe/iCloud ones are.
Valid AIM Screen Names in Table (pic)
7:46 PM Monday; December 5, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
What about when using the "Time Capsule" HD as the external disk, especially when it is connected by ethernet cable? I'm having trouble getting it to work at all. Don't need it to work as anything else, other than a ethernet connected Time Machine backup. Already have a wireless network that works fine so no need to mess with it. We get the internet via cable company and their modem is upstairs and the Time Capsule is downstairs in the basement. The latest error message was about it could not backup as it was already in use (should have written it down before clicking OK and moving on.
See if this helps...
http://pondini.org/TM/C12.html -
I am having trouble printing I have a connection to my printer wirelessly but does not print out the correct page I want.When I do print I get a bunch of pages more than is needed and also get a code and symbols please help I am jammed at work
This can be the result of selecting the wrong driver. An older, unsupported laser printer will sometimes work with the generic Postscript driver.
-
I am having trouble getting mail from the shaw server that my new iMac is connected to. I have to reboot the system to get Outlook for Mac to access the system and obtain new messages. Any ideas? Its at the point where I have started using the PC again as its less trouble.......
In Firefox 3.6.4 and later the default connection settings have been changed to "Use the system proxy settings".<br />
See "Firefox connection settings" in [[Server not found]]
You can find the connection settings in "Tools > Options > Advanced : Network : Connection"<br />
If you do not need to use a proxy to connect to internet then select No Proxy -
Having trouble getting my bluetooth from iPhone 5 to connect with PolarH7 Heart Sensor.
Having trouble getting my bluetooth from iPhone 5 to connect with PolarH7 Heart Sensor. when in settings Bluetooth is on but not reading devide ( it satyas at Now Discoverable) .
bradbev,
Welcome to the community! Thanks to everyone for the help. I do agree that adding and removing the Yahoo! e-mail account is the best first step to get this resolved. Below I have the steps to remove and re-add the account.
Remove a Personal Email Account
Add a Personal Email Account
Thank you!
AdamE_VZW
Follow Us on Twitter @VZWSupport -
I am having trouble getting my ipad to communicate with sat connection I have tried turning off and on re installing the sat connection but still cannot get safari to load
Hello Brenda,
Thank you for the details of the issue you are experiencing with your iPad. It sounds like you're not able to access the Internet on your iPad. I found a couple of resources that will help.
If you are having trouble connecting to the Internet using Wi-Fi, I recommend the following article:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
If you are not able to access the Internet when connected to a cellular network, I recommend the following article:
iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection
http://support.apple.com/kb/TS4249
Thank you for using Apple Support Communities.
Best,
Sheila M. -
Trouble getting Power PC G4 to connect to my wireless network (sonnet aria)
I have an existing wireless lan. Wanted to move the router to a more central location and bought a Sonnet Aria Extreme Wireless PCI for the G4 desktop. The PCI card popped in just fine but I can't get the G4 to connect.
The instructions that came with the PCI card described the procedures but I've followed them and still can't get the G4 to see the network. Tested with a laptop and the signal is great.
The router is a Linksys WRT54G. I've made sure it is broadcasting the ssid.
Before I post the results I'd like to have some help on what the major steps need to be. Do I need to set up an Airport base station? Do I just set up the network via system preferences?
If someone can give me a start point I can post back what I'm seeing.
Thanks
TomThere is absolutely no reason for an AirPort base station.
Since this is a non-Apple solution you will need to follow the Sonnet Aria instructions on what software to use and how to configure the settings to join your wireless network. -
Trouble getting Cisco 2600 Series AP to stay joined to WLC 5508
Hi,
I have recently been tasked with upgrading our old Autonomous APs to LWAPs. We have a 5508 WLC at our Virtual Co-Lo and I am using Flexconnect to accomadate local switching and dhcp at our sites. I have upgraded over 50 APs and joined them to the controller. These include only 1130AG and 1240AG models. However they are working flawlessly and staying connected to the controller. The issue I'm having is with a new batch of 2600 series APs staying connected to the controller. I have attempted to do research into what may be causing the disconnects but have yet to find a solution. I am using DNS to resolve the CAPWAP & LWAPP queries from the APs to the controller accross our WAN. In reading other posts I thought it may be an issue with packets getting dropped but have had our Vendor who manages Sonicwalls at both ends of the WAN confirm for me there is no packet loss. Below are logs I gathered using puttty from the AP & WLC. Any help would be greatly appreciated.
AP I'm doing the testing on:
NAME: "AP2600", DESCR: "Cisco Aironet 2600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP2602I-A-K9 , VID: V01, SN: FTX1740J8V1
WLC in question:
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.3.112.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... wificontroller
System Location.................................. Corp
System Contact................................... Net Engineer
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.250.32.8
Last Reset....................................... Software reset
System Up Time................................... 190 days 3 hrs 34 mins 24 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
--More-- or (q)uit
Internal Temperature............................. +38 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 14
Number of Active Clients......................... 71
Burned-in MAC Address............................ C8:9C:1D:8C:52:E0
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 100
Here is the output that keeps on occuring as the AP joins the WLC for a brief time and then changes to standalone mode
WT-4thFlr-AP3#
*Dec 14 15:42:04.419: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
., 3)
*Dec 14 15:42:11.443: %EVT-4-WRN: Write of flash:/event.capwap done
*Dec 14 15:42:11.483: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
*Dec 14 15:42:11.487: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Dec 14 15:42:11.487: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.250.32.8:5246
*Dec 14 15:42:11.571: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Dec 14 15:42:21.575: %CAPWAP-3-ERRORLOG: Selected MWAR 'wificontroller'(index 0).
*Dec 14 15:42:21.575: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Dec 14 15:42:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
*Dec 14 15:42:14.303: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.250.32.8 peer_port: 5246
*Dec 14 15:42:14.303: %CAPWAP-5-SENDJOIN: sending Join Request to 10.250.32.8
*Dec 14 15:42:15.127: Starting Ethernet promiscuous mode
*Dec 14 15:42:15.535: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Dec 14 15:42:15.667: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
*Dec 14 15:42:15.667: Setting AC first hop MAC: 0017.c575.a23c
*Dec 14 15:42:15.855: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller wificontroller
*Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Dec 14 15:42:15.911: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*Dec 14 15:42:15.915: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration file
*Dec 14 15:42:15.915: %LWAPP-3-CLIENTERRORLOG: Switching to Connected mode
*Dec 14 15:42:23.639: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Dec 14 15:42:34.615: %CLEANAIR-6-STATE: Slot 0 disabled
*Dec 14 15:42:34.615: %CLEANAIR-6-STATE: Slot 1 disabled
*Dec 14 15:45:43.783: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
., 11)
*Dec 14 15:45:43.787: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
*Dec 14 15:45:43.787: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Dec 14 15:45:43.787: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.250.32.8:5246
*Dec 14 15:45:43.867: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Dec 14 15:45:53.867: %CAPWAP-3-ERRORLOG: Selected MWAR 'wificontroller'(index 0).
*Dec 14 15:45:53.867: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Dec 14 15:45:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246
*Dec 14 15:45:46.315: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.250.32.8 peer_port: 5246
*Dec 14 15:45:46.315: %CAPWAP-5-SENDJOIN: sending Join Request to 10.250.32.8
*Dec 14 15:45:46.487: Starting Ethernet promiscuous mode
*Dec 14 15:45:49.903: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Dec 14 15:45:50.031: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1
*Dec 14 15:45:50.031: Setting AC first hop MAC: 0017.c575.a23c
Here are the results of debug capwap client event on the AP:
WT-4thFlr-AP3#debug capwap client event
CAPWAP Client EVENT display debugging is on
WT-4thFlr-AP3#
*Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
*Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:54:58.335: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
*Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:54:58.343: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
*Dec 14 15:55:08.000: %CAPWAP-3-EVENTLOG: Setting time to 15:55:08 UTC Dec 14 2013
*Dec 14 15:55:25.579: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:55:25.587: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
*Dec 14 15:55:25.827: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:55:25.835: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
*Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
*Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:55:55.835: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
*Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:55:55.843: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
*Dec 14 15:55:56.000: %CAPWAP-3-EVENTLOG: Setting time to 15:55:56 UTC Dec 14 2013
*Dec 14 15:56:25.735: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:56:25.743: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
*Dec 14 15:56:25.983: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:56:25.991: %CAPWAP-3-EVENTLOG: Wtp Event Response from 10.250.32.8
*Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Echo Interval Expired.
*Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Sending packet to AC
*Dec 14 15:56:55.991: %CAPWAP-3-EVENTLOG: Echo Request sent to 10.250.32.8
*Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Resetting reTransmissionCnt to 0
*Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Queue Empty.
*Dec 14 15:56:55.999: %CAPWAP-3-EVENTLOG: Echo Response from 10.250.32.8
*Dec 14 15:56:56.000: %CAPWAP-3-EVENTLOG: Setting time to 15:56:56 UTC Dec 14 2013
Here are the results of debug capwap client packet detail:
WT-4thFlr-AP3#
*Dec 14 15:59:01.823: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:01.823: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:01.823: Msg Type : CAPWAP_ECHO_REQUEST
*Dec 14 15:59:01.823: Msg Length : 0
*Dec 14 15:59:01.823: Msg SeqNum : 44
*Dec 14 15:59:01.823: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:01.831: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:01.831: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:01.831: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:01.831: Msg Type : CAPWAP_ECHO_RESPONSE
*Dec 14 15:59:01.831: Msg Length : 15
*Dec 14 15:59:01.831: Msg SeqNum : 44
*Dec 14 15:59:01.831:
*Dec 14 15:59:01.831: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 11
*Dec 14 15:59:01.831: Vendor Identifier : 0x00409600
*Dec 14 15:59:01.831:
*Dec 14 15:59:01.831:
IE : UNKNOWN IE 151
*Dec 14 15:59:01.831: IE Length : 5
*Dec 14 15:59:01.831: Decode routine not available, Printing Hex Dump
*Dec 14 15:59:01.831:
52 AC 80 46 00
*Dec 14 15:59:01.831: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:20.931: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:20.931: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:20.931: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:20.931: Msg Type : CAPWAP_CONFIGURATION_UPDATE_REQUEST
*Dec 14 15:59:20.931: Msg Length : 93
*Dec 14 15:59:20.931: Msg SeqNum : 38
*Dec 14 15:59:20.931:
*Dec 14 15:59:20.931: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 89
*Dec 14 15:59:20.931: Vendor Identifier : 0x00409600
*Dec 14 15:59:20.931:
*Dec 14 15:59:20.931:
IE : RRM_NEIGHBOR_CTRL_PAYLOAD
*Dec 14 15:59:20.931: IE Length : 83
*Dec 14 15:59:20.931: Decode routine not available, Printing Hex Dump
*Dec 14 15:59:20.931:
00 0A FA 20 08 01 F4 00 07 0A FA 20 08 03 00 01
01 00 3C 00 B4 2E 06 2E E7 B4 94 51 B2 C7 79 25
22 FD BE 04 F6 00 00 00 00 00 00 00 00 4F 50 52
53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 01 06 0B
01 01 01
*Dec 14 15:59:20.931: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:20.931: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:20.931: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:20.931: Msg Type : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
*Dec 14 15:59:20.931: Msg Length : 8
*Dec 14 15:59:20.931: Msg SeqNum : 38
*Dec 14 15:59:20.931:
*Dec 14 15:59:20.931: Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
*Dec 14 15:59:20.931: Result Code : CAPWAP_SUCCESS
*Dec 14 15:59:20.931: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:21.139: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:21.139: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:21.139: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:21.139: Msg Type : CAPWAP_CONFIGURATION_UPDATE_REQUEST
*Dec 14 15:59:21.139: Msg Length : 111
*Dec 14 15:59:21.139: Msg SeqNum : 39
*Dec 14 15:59:21.139:
*Dec 14 15:59:21.139: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 107
*Dec 14 15:59:21.139: Vendor Identifier : 0x00409600
*Dec 14 15:59:21.139:
*Dec 14 15:59:21.139:
IE : RRM_NEIGHBOR_CTRL_PAYLOAD
*Dec 14 15:59:21.139: IE Length : 101
*Dec 14 15:59:21.139: Decode routine not available, Printing Hex Dump
*Dec 14 15:59:21.143:
01 0A FA 20 08 01 F4 00 07 0A FA 20 08 0C 00 01
01 00 3C 00 B4 2E 06 2E E7 B4 94 51 B2 C7 79 25
22 FD BE 04 F6 00 00 00 00 00 00 00 00 4F 50 52
53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 24 28 2C
30 34 38 3C 40 95 99 9D A1 01 01 01 01 01 01 01
01 01 01 01 01
*Dec 14 15:59:21.143: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:21.143: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:21.143: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:21.143: Msg Type : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
*Dec 14 15:59:21.143: Msg Length : 8
*Dec 14 15:59:21.143: Msg SeqNum : 39
*Dec 14 15:59:21.143:
*Dec 14 15:59:21.143: Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
*Dec 14 15:59:21.143: Result Code : CAPWAP_SUCCESS
*Dec 14 15:59:21.143: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:25.547: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:25.547: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:25.547: Msg Type : CAPWAP_WTP_EVENT_REQUEST
*Dec 14 15:59:25.547: Msg Length : 14
*Dec 14 15:59:25.547: Msg SeqNum : 45
*Dec 14 15:59:25.547:
*Dec 14 15:59:25.547: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*Dec 14 15:59:25.547: Vendor Identifier : 0x00409600
*Dec 14 15:59:25.547:
*Dec 14 15:59:25.547:
IE : RRM_LOAD_DATA_PAYLOAD
*Dec 14 15:59:25.547: IE Length : 4
*Dec 14 15:59:25.547: slot 0 rxLoad 0 txLoad 0 ccaLoad 33
*Dec 14 15:59:25.547: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:25.555: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:25.555: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:25.555: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:25.555: Msg Type : CAPWAP_WTP_EVENT_RESPONSE
*Dec 14 15:59:25.555: Msg Length : 0
*Dec 14 15:59:25.555: Msg SeqNum : 45
*Dec 14 15:59:25.555: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:25.795: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:25.795: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:25.795: Msg Type : CAPWAP_WTP_EVENT_REQUEST
*Dec 14 15:59:25.795: Msg Length : 14
*Dec 14 15:59:25.795: Msg SeqNum : 46
*Dec 14 15:59:25.795:
*Dec 14 15:59:25.795: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*Dec 14 15:59:25.795: Vendor Identifier : 0x00409600
*Dec 14 15:59:25.795:
*Dec 14 15:59:25.795:
IE : RRM_LOAD_DATA_PAYLOAD
*Dec 14 15:59:25.795: IE Length : 4
*Dec 14 15:59:25.795: slot 1 rxLoad 0 txLoad 0 ccaLoad 0
*Dec 14 15:59:25.795: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:25.803: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:25.803: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:25.803: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:25.803: Msg Type : CAPWAP_WTP_EVENT_RESPONSE
*Dec 14 15:59:25.803: Msg Length : 0
*Dec 14 15:59:25.803: Msg SeqNum : 46
*Dec 14 15:59:25.803: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:30.375: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:30.375: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:30.375: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:30.375: Msg Type : CAPWAP_CONFIGURATION_UPDATE_REQUEST
*Dec 14 15:59:30.375: Msg Length : 17
*Dec 14 15:59:30.375: Msg SeqNum : 40
*Dec 14 15:59:30.375:
*Dec 14 15:59:30.375: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 13
*Dec 14 15:59:30.375: Vendor Identifier : 0x00409600
SlotId : 0
Mobile Mac Addr : BC:52:B7:E3:17:CB
*Dec 14 15:59:30.375: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:30.375: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:30.375: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 15:59:30.375: Msg Type : CAPWAP_CONFIGURATION_UPDATE_RESPONSE
*Dec 14 15:59:30.379: Msg Length : 8
*Dec 14 15:59:30.379: Msg SeqNum : 40
*Dec 14 15:59:30.379:
*Dec 14 15:59:30.379: Type : CAPWAP_MSGELE_RESULT_CODE, Length 4
*Dec 14 15:59:30.379: Result Code : CAPWAP_SUCCESS
*Dec 14 15:59:30.379: <<<< End of CAPWAP Packet >>>>
*Dec 14 15:59:30.387: <<<< Start of CAPWAP Packet >>>>
*Dec 14 15:59:30.387: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 15:59:30.387: HLEN 2, Radio ID 0, WBID 1
*Dec 14 15:59:30.387: Msg Type : CAPWAP_WTP_EVENT_RESPONSE
*Dec 14 15:59:30.387: Msg Length : 0
*Dec 14 15:59:30.387: Msg SeqNum : 47
*Dec 14 15:59:30.387: <<<< End of CAPWAP Packet >>>>
*Dec 14 16:00:00.387: <<<< Start of CAPWAP Packet >>>>
*Dec 14 16:00:00.387: CAPWAP Control mesg Sent to 10.250.32.8, Port 5246
*Dec 14 16:00:00.387: Msg Type : CAPWAP_ECHO_REQUEST
*Dec 14 16:00:00.387: Msg Length : 0
*Dec 14 16:00:00.387: Msg SeqNum : 48
*Dec 14 16:00:00.387: <<<< End of CAPWAP Packet >>>>
*Dec 14 16:00:00.395: <<<< Start of CAPWAP Packet >>>>
*Dec 14 16:00:00.395: CAPWAP Control mesg Recd from 10.250.32.8, Port 5246
*Dec 14 16:00:00.395: HLEN 2, Radio ID 0, WBID 1
*Dec 14 16:00:00.395: Msg Type : CAPWAP_ECHO_RESPONSE
*Dec 14 16:00:00.395: Msg Length : 15
*Dec 14 16:00:00.395: Msg SeqNum : 48
*Dec 14 16:00:00.395:
*Dec 14 16:00:00.395: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 11
*Dec 14 16:00:00.395: Vendor Identifier : 0x00409600
*Dec 14 16:00:00.395:
*Dec 14 16:00:00.395:
IE : UNKNOWN IE 151
*Dec 14 16:00:00.395: IE Length : 5
*Dec 14 16:00:00.395: Decode routine not available, Printing Hex Dump
*Dec 14 16:00:00.395:
52 AC 80 81 00
*Dec 14 16:00:00.395: <<<< End of CAPWAP Packet >>>>Under my AP Policies I only have "Accept Manufactured Installed Certificate (MIC)" checked. I attempted to add the AP based on MAC Address (c0:67:af:6f:25:70) with this certificate type but still have the same issue. I then ran the following debug on my controller and this is the output I recieve regarding that MAC. I tried to cut the output short because it get's somewhat redundant but was unsure what exactly to look for in the output. Should I be selecting a different certificate type? I am somewhat new to wireless technologies but doing my best to pick things up so if this seems trivial please forgive my ignorance.
debug pm pki enable
*sshpmLscTask: Dec 14 20:42:56.450: sshpmLscTask: LSC Task received a message 4
*spamApTask6: Dec 14 20:42:58.840: sshpmGetIssuerHandles: locking ca cert table
*spamApTask6: Dec 14 20:42:58.841: sshpmGetIssuerHandles: calling x509_alloc() for user cert
*spamApTask6: Dec 14 20:42:58.841: sshpmGetIssuerHandles: calling x509_decode()
*spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: C=US, ST=California, L=San Jose, O=Cisco Systems, CN=AP3G2-c067af6f2570, [email protected]
*spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: O=Cisco Systems, CN=Cisco Manufacturing CA
*spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Mac Address in subject is c0:67:af:6f:25:70
*spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Cert Name in subject is AP3G2-c067af6f2570
*spamApTask6: Dec 14 20:42:58.845: sshpmGetIssuerHandles: Cert is issued by Cisco Systems.
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: called to evaluate
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: called to get cert for CID 282aef7e
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
*spamApTask6: Dec 14 20:42:58.845: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
*spamApTask6: Dec 14 20:42:58.845: ssphmUserCertVerify: calling x509_decode()
*spamApTask6: Dec 14 20:42:58.856: ssphmUserCertVerify: user cert verfied using >cscoDefaultMfgCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (current): 2013/12/15/01:42:58
*spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (NotBefore): 2013/08/25/13:01:22
*spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: ValidityString (NotAfter): 2023/08/25/13:11:22
*spamApTask6: Dec 14 20:42:58.856: sshpmGetIssuerHandles: getting cisco ID cert handle...
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: called to evaluate
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
*spamApTask6: Dec 14 20:42:58.856: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
*spamApTask6: Dec 14 20:42:58.857: sshpmFreePublicKeyHandle: called with 0x2c5f0cb8
*spamApTask6: Dec 14 20:42:58.857: sshpmFreePublicKeyHandle: freeing public key
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: called to evaluate
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: called to get cert for CID 183fd2b6
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<
*spamApTask0: Dec 14 20:43:17.451: sshpmGetCID: called to evaluate -
Hi, I am having trouble getting an album to download. I have tried it on both my iPhone and laptop through iTunes but neither works. I am wondering if it could be the size of the album stopping it downloading (212 Tracks) Any Ideas?
These alerts occur due to timeouts or conflicts trying to write a file during download.
If you encounter this issue while while downloading something from the iTunes Store:
Delete your iTunes Downloads folder, located in:
Mac OS X: ~/Music/iTunes/iTunes Media/Downloads Note: "iTunes Media" may appear as "iTunes Music. Also, the tilde (~) refers to your Home directory.
After locating your iTunes Downloads folder:
Quit iTunes.
Delete the Downloads folder on your computer.
Open iTunes.
Choose Store > Check for Available Downloads.
Enter your account name and password.
Also review this support aticle as it might be causing due to internet connection: http://support.apple.com/kb/ts1368
Hope this helps.
Maybe you are looking for
-
How to implement SAP organizational Calendar in my application?
Hi, I have to create an application page that could either be developed in Web Dynpro or JSP. This page should contain a list of countries and when the user selects a country, the page must make use of the SAP Organizational Calendar to fill a grid w
-
Smart Object opening as .jpg instead of .psb
I received a file from another person – I didn't create it. It contains a Smart Object, which is indicated in the layer thumbnail. When I double-click to edit the smart object, a .jpg file opens, not a .psb. I know I can flatten it after making the c
-
A Tab History (Recent pages in "A Tab")
Hi In older versions of mozilla firefox we had a little symbol near "back" button that showed a list of sites that you visited them apart (separate) from other Tabs history. but in version 4 this function is not there. you can see what I say using th
-
Where does EBS store customized LOV elements?
Dear All, We are developing a report on EBS r12 >> Payables >> Payments screen. The Functional Consultants Team added a DFF ( view_inv_pay.DESC_FLEX ) with only 1 segment and its description at the Invoice Payment block level ( VIEW_INV_PAY ) which s
-
I need to send a message via socket from a C program to a Java program
Hi, I need to send a message via socket from a C program to a Java program. The message has three data: a long, an integer and a string. How can I put those three fields in a array of bytes in C? How can I extract those same three fields from an arra