Trouble using the counter on PCI 6025E

Hello,
I am facing a problem with the counter on PCI 6025E. I am trying to count the number of pulses generated by the shaft encoder mounted on the shaft of a motor. I am using a channel from the shaft encoder to count the pulses and generate the line state. So, I have wired the channel to pins 25[line state]and 47[counter]on SCB-100. In my application I am using the count events/time vi from DAQ palette. Every time I run my application I have been getting the error NI 10001 saying that the ordering of the strings is not as expected.

Hi,
The Count Events & Time.vi is typically used with older counter hardware such as the 9513 chip. Your E Series card (6025E) uses a DAQ-STC chip. The best way to count your edges is to open up the example "Count Edges(DAQ-STC).vi which can be found by selecting Help>>Find Examples... and you will find it under the DAQ Counter examples as an DAQ-STC example. Hope that helps.
Ron

Similar Messages

How do I use the counter and digital signals of the 6071E while it is connected to SCXI modules?

I am contemplating using a PCI 6071E with SCXI. We have the boards (6071E), we would need the cable (I suppose SH1006868) and the SCXI system. I would like to know how would you access the counter and digital line capabilities of the board. I will be using a SCXI-1314 with a SCXI-1520 Module for strain measurements but will need to use the counter and digital lines of the board as well. Can this be done? If so, how and/or what else do I need?

I think this KnowledgeBase will answer the question for you.
Accessing DAQ Board Counter Pins with an SCXI System
Otis
Training and Certification
Product Support Engineer
National Instruments

I'm having trouble using the iTunes and Apps store because i can't register my Nigerian mastercard. What should i do. i'm trying to register it in the Nigerian iTunes store.

I'm having trouble using the iTunes and Apps store because i can't register my Nigerian mastercard. What should i do. i'm trying to register it in the Nigerian iTunes store.

Is this a new Apple iD? If it is, and you have already set it up, then you have two options:
1. Temporarily put a Credit Card or Gift Card on the account to download the free app. If you put a credit card, then once you have downloaded the app, you should be able to go into your Account preferences and change the payment option to = None.
2. You can download the fee App, and then set up a new Apple ID.
Cheers,
GB

Trouble using the Web-based utility

I have a WRT54G wireless router, V8, firmware 8.0.0. It is Ethernet-connected to a Windows Vista machine running SP1.
I am having trouble using the Web-based utility. I can access it but cannot make any changes. For instance, if I change the settings on the Setup page and click "save", I get a "This webpage is not available"
I tried updating the firmware and got the same message. Disabling my personal firewall has no effect. Resetting the router from the button on its rear panel has no effect. I tried using with both Windows IE and Google Chrome browsers and got the same result.
I have been using this router without problem for months using a a Windows XP machine. This problem may be associated with my changing it to the current Windows Vista machine. I no longer have the Windows XP machine.
Please help me. Thank you and Happy New Year!
- tom

I spent a full day unsuccessfully trying to make it work, including numerous Linksys utilities downloaded from the site. I could not conjure any support on Linksys chat, and the live body on the Linksys tech support line wanted to charge me $29 for his help.
I finally succeeded by purchasing and installing a Netgear wireless router ($44, Staples) that came up flawlessly the first time. The Linksys device is in my trash.

Hi, I am having trouble using the smooth tool on a logo that I created. I have watched tutorials and something isn't working for me. When trace with the smooth the line just disappears and doesn't smooth anything out. Please help.

Hi, I am having trouble using the smooth tool on a logo that I created. I have watched tutorials and something isn't working for me. When trace with the smooth the line just disappears and doesn't smooth anything out. Please help.

Sorry, that's Monika with a k
On Tue, Nov 18, 2014 at 2:26 PM, Monika Gause <[email protected]>

Using timer/counter with PCI-6221/USB-6210 to control timed-loop VI

Dear all,
I need to ask about two devices and one of their functionalities, PCI-6221 and USB-6210. For our NI-based system, we need to control some timings in a Timed-Loop vi, for that currently we are using PCI-6221 and we give external TTL signal (at 1 kHz) to it,
recenntly we need to make some changes and for that we found USB 6210 DAQ to be more suitable, but we need to clear ourselves on some specific things.
Can the counter/timers functions available in the either PCI 6221 or USB 6210 can be used to control the Timed-loop VI by giving external clock or by using their own internal clock source?
Although we are using external clock with the PCI 6221 but we want to know about the usage of their internal clock, also are controlling timed-loop also possible for USB-6210
Also... What if we use the RTOS, are they still able to control the timed-loop VI without giving any 'EXTERNAL CLOCK' and using the internal clock sources of the DAQs
Waiting for reply,
Bests,
RaJaf
Solved!
Go to Solution.

Ben,
I having read previous email which I send earlier with general overview, we discussed in more detail within our team and I am giviing the specific answers.
Please check in RED the most recent answers. Blue are the questions/suggestions by your side.
1.    Using Internal hardware clock of PCI-6221 would enable us get rid of external clock, but how to divert the internal hardware clock to the current settings. Any idea (can you provide us with some reference manul for otherwise). I mean is there some flag-bit etc. or VI
2.       Is it also meant that with the installation of RTOS the timed-loop can directly get the timing source from the internal hardware clock PCI-6221? --- How???
3.       In order to make desktop to work as RT system, what is the hardware (motherboard, processor, etc..) requirement? What are the LabVIEW modules (specific name) that needed to be installed? Our platform is LabVIEW 8.6. (Currently we have windows-7 with i7 core processor)
What kind of application are you intending for this system? ---- high-speed laser scanning system.
Are you most concerned about accuracy, speed, or responsiveness? To control the laser mirror scanner to move at 1 kHz or 2 kHz speed. On the other hands, using PCI-5105 (128 MB memory) as a DAQ for real-time/on-the-fly data processing.
Bests,
RAJAF

Using a counter on PCI-6023E DAQ card

Hi there,
I'm about to use a 6023 card to measure a periodic pulse signal. I need to count the number of the pulses. But...I've heard that the counters on my card are unusable in that case. Is that correct? Do I have to chage my card? Or can I do it with 6023E?
Thanks in advance;
Radek

Hi DAC,
The counter on your 6023E board is the DAQ-STC counter/timer. This counter fully supports counting the number of pulses. Depending on your application development environment, if you search the shipping examples you will find examples that perform this function.
This is so long as your digital pulses are 0-5 V or TTL compatible.
Other applications supported by your counter are:
Simple event counting
Gated-event counting
Single-period measurement
Single pulse-width measurement
Single pulse generation
Single triggered pulse generation
Retriggerable single pulse generation
Continuous pulse-train generation
Buffered event counting
Buffered period measurement
Buffered semi-period measurement
Buffered pulse-width measurement
Fre
quency measurement
Buffered frequency measurement
Finite pulse-train generation
Quadrature encoders
Hope that helps. Have a good day.
Ron
Application Engineering
National Instruments

Has anyone tried to use the Intel 750 PCIe AIC in a Z640 Workstation

I am really only interested in using this as a second disc , not the main OS Boot disk; as I have heard there could be a problem having the right NVMe Bios or UEFI .
I was advised by a reseller not to do this as HP tested recommended discs for heat generation and airflow. But that seemed strange, as one can have 2 Nvidia K2200s in the chassis and they each max at 68 watts, and each PCIe slot has a max limit of 75 watts. So surely using the Intel 750 which has a max power consumption of 24 watts should generate a lot less heat?
That assumes my mikey mouse knowledge of physics is watt equate to heat generation or are SSDs different?
I could understand it if the Intels were say 68 watts - i.e. It could then be down to cooling airflow. Or is the intelligent cooling system advised of known components and therefore reacts differently i.e. Maybe boosts the fan speed or something.
Hence would love to hear from anyone who has actually done it - how did it work out? Or someone who really understand these boxes at a deep technical level, who could rationalise why this is not a good thing ........ Other than the HP reseller doesnt sell the Intel 750s but does sell the overpriced, relatively speaking underperforming Z Turbo drives.

I have not done this but did look after Macs in a class room enviroment. I think your concerns are valid, you may be making a difficult situtation worse.
If no one come back with a definite answer, you could try a small number as a pilot, and keep them on machines next to each other. That may give you a better understanding of any likey problems.
What are the the problems with the wired headphones, cable breaks? If so woud headsets with detachable cables be an easier answer?

I just had my logic board replaced. now im having trouble using the interent even with a strong connection and the internet is working on other devices!! please help me :(

I just had my logic board replaced. i am now having trouble with using the interent even with a strong connection. all other devices are having no problem with the internet. please help

Test while started in Recovery : if the problem persists, then it likely is a hardware issue.
Resetting the System Management Controller (SMC) probably won't change anything, but you can readily do it before contacting the repairers.

I'm having trouble using the safari. It won't open the screen stays black

I'm having trouble with the safari it won't open the screen stays black also apps won't open it just kicks me out

Try this:
Settings>Safari>Clear History, Cookies and Data

Trouble using the Reviewer feature on Captivate 4

I'm using the trial of Captivate 4 (contemplating the upgrade from CS3) and the only problem I have encounterd is with the Reviewer feature. I published a review to email, sent it to half dozen co-workers, checked the boxes to attach the AIR & CREV files. When I opened the email myself, the Reviewer loaded & the CREV played fine, however all of my co-workers got an error message (error #3003) telling them that installation failed and they should try again. I checked, and these folks have AIR installed on their PC's and the Captivate Reviewer shows up afterwards on their desktop. But they can't open the CREV file. Any body know why that's happening?

Hello,
What is the language of the OS? Over here some problems with CREV when using a Dutch OS.
Lilybiri

Anyone have trouble using the av component?

when i plug in the av component, only the audio and not video comes through...grr. any troubleshooting advice?

My Thinkvision monitor has a hardware switch allowing you to choose DVI or VGA when using dual cables. What happens if you in integrated graphics mode using your monitor in VGA, switch the monitor to DVI first? According to that footnote the T400 should no longer recognize there is an external monitor attached so allow the switch to discrete mode. And if it no longer recognizes there is an external monitor wouldn't it automatically turn on its own LCD screen so you see what you are doing when going to the power manager for the graphic mode switch?
Sorry I can't test as I am using the modded ATI driver at the moment (see the voluminous display driver "amdkmdap" crashes thread.)
T500: Vista 32, 2.8GHz, 4GB RAM, 15.4" 1680x1050, 500GB 7200rpm, ATI Radeon HD3650 + Intel 4500MHD. T42: XP, 1.7GHz, 2GB RAM, 14.1" 1024x768, 250GB PATA, ATI Radeon 7500.

Trouble using the Voice Separation Tool in the Score Editor.

Hello,
I am trying to change the notes in a piano score from the treble clef to the bass clef and vice versa.
I've tried going under Score Editor>Layout>Staff Styles, choosing piano 1/3 and making sure the channels were set, but it doesn't seem to actually change anything. And when I try to use the Voice Separation Tool, I just get the message: "The Voice Separation tool only works for polyphonic staff styles with MIDI channel assignments."
I am new to Logic and am sure it's something very basic that I'm missing.
Many thanks for the help!
~JD

Hi
You must actually assign the Staff Style to the regions in the top left of the Score Inspector:
CCT

I am having trouble using the IMAQ command RejectBorder. Can somebody give me some guidance?

My image is 768x576, which I confirmed by right-clicking on the Image Info property. I set a border using the Image.Border = 20.
When I threshold, then do a RejectBorder, blobs along the top and left sides of the image are eliminated, but not those along the right or bottom.
Any ideas?

Try setting the property image.BorderWidth to be different values and see if this changes the blobs that are eliminated. The border should be even all the way around the image.
Take a look at the example program called Blob Analysis in the folder C:\Program Files\National Instruments\VB\Samples\IMAQ\2. Functions\Binary Analysis for an example of using this function.
Hope this helps -
Julie S
Applications Engineer
National Instruments

Trouble using the instrument driver for the "hp8753b"

I am using the instrument driver for the "hp8753b", specifically the "collect and display data" driver. I manually set my settings to the analyzer and run the VI (i.e. set start frequency to 500 kHZ and stop frequency to 1 GHz), when the VI runs with the "collect and display data" it defaults to start frequency 1 GHz and stop frequency to 3 GHz. I have tried to modify the driver to only collect data and not to modify any settings on the analyzer but I run into errors. Any help on this is appreciated.

Hello,
I have installed the instrument driver you mention in your post. I am looking at the Collect and Display Data.vi, however I need more information from you to determine why your sweep is defaulting back to 1GHz-3GHz.
When you say "I manually set my settings to the analyzer" are you making these settings directly on the analyzer? The Collect and Display Data.vi seems to read all of the settings from the hardware, I did not see any configuration in the VI. What modifications were you making to the VI and what errors were you getting?
Can you see the range on the instrument? If so , can you determine at which point the range defaults back to the higher range? Running in highlight-execution mode in the VI and running NI-Spy (Start->All Programs->National Instruments->NI-Spy) to perform a capture of the GPIB commands can help to determine at what point the errors are occurring. It will also let you see if there are any commands being sent which cause the instrument to be reset.
Jennifer O.

Trouble using the counter on PCI 6025E

Similar Messages

Maybe you are looking for