Trouble with 802.1x profile

Hi there,
I work at a University, and after a recent network change all of our campus wifi networks require 802.1x authentication. This works fine for all but a couple of labs which use laptops, and thus require an 802.1x profile be built for the loginwindow so students can use their AD accounts to log in.
I should probably also mention that the accounts are mobile accounts, and are removed after logoff (via a LogoutHook). We're running OS X 10.8.5 through 10.10.2.
So far, I've built n-thousand variations of the 802.1x profile in ProfileManager, but am still completely unable to get this working.
I'll start off with a rough overview our security settings, and what I've done so far:
WPA2 Enterprise, PEAP with MSCHAPv2
When logged in to a machine, trusting the following certificates and saving the user-supplied credentials will successfully allow a user to reconnect unprompted for credentials, but the (seemingly) same settings in the 802.1x profile don't work (or I'm configuring it incorrectly).
Symantec Class 3 Secure Server CA - G4
VeriSign Class 3 Public Primary Certification Authority - G5
Also, the leaf / radius server certificate becomes trusted, but does not have to be explicitly downloaded (as far as I know- but I have tried supplying it as well).
In the 802.1x profile, I've tried just about every permutation of settings I can think of, but I'll outline my general process (in case I'm missing something).
I add the certificate payload with the 2 certificates listed above (I've also tried it with the leaf certificate).
In the network payload, I
1) enter the SSID
2) set to AutoJoin
3) set WPA2 Enterprise security
4) check "Use as LoginWindow configuration"
5) check PEAP under protocols
6) add a 'filler' name to OuterIdentity (everything I read said it doesn't matter what's entered)
In the Trust tab:
7) check the 2 certificates added in the cert payload
8) enter the FQDN of the RADIUS server (xxx-radius.xx.xxxxx.edu) in the Trusted Server Certificate Names (this is the same as the cert for the server found in Keychain Access)
I've figuratively tried millions of variants (e.g. add the leaf cert to the cert payload / trust settings | add no cert payload, just radius server fqdn under TSCN section | etc.)
Any tips on what I'm doing wrong?
Thank you,
Eric

hi, if the problem still persists, have you tried clearing out any 802.1x profiles you have saved?
Go to System Preferences > Network, click on Airport, choose Advanced, go to the 802.1x tab, look at the section on the left side that has User Profiles. Select the profile and hit the minus button at the bottom of the pane.
A lot of these issues seem to be helped by clearing out any saved data about the wireless network, and setting it up manually again. We have seen many issues here at Notre Dame with Macs vs 802.1x. Hoping Apple makes it more reliable soon.

Similar Messages

Trouble with 802.1x authentication

Hello. I live in a dorm, and we connect to the Net over 802.1x authentication. Everything worked OK, until two days ago. Now I can no longer authenticate my Mac on the network and connect to the Net.
I get the following error:
"802.1X is unable to authenticate. It is possible that the configuration you have provided is invalid. If you are unsure about what configuration to connect with, check with your network administrator.
(Error: 1 on port en0)"
My configuration seems to be ok (I didn't change anything about it, it just stopped working), username and password are also correct. Also other computers can connect to the network, and my LAN card works normally otherwise, only it can't pass the 802.1x authentication :S I'm connected now over my LinuxBox which shares the connection to my Mac, so obviously my LAN card is not broken...
What could be the problem?
cheers!

hi, if the problem still persists, have you tried clearing out any 802.1x profiles you have saved?
Go to System Preferences > Network, click on Airport, choose Advanced, go to the 802.1x tab, look at the section on the left side that has User Profiles. Select the profile and hit the minus button at the bottom of the pane.
A lot of these issues seem to be helped by clearing out any saved data about the wireless network, and setting it up manually again. We have seen many issues here at Notre Dame with Macs vs 802.1x. Hoping Apple makes it more reliable soon.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

Help with 802.1x wifi profile

Hi All,
I am in a bit of a bind. I have been tasked with creating an 802.1x profile for Lion and up machines based on the profiles we use for our Windows machines and I have not been able to get this to work. Our radius server is Win 2K8 R2 based, and uses various AD based methods for authentication.
Radius needs the following:
- Microsoft: Protected EAP (PEAP)
- TLS (for MSCHAPv2 settings)
PEAP Properties
- Validate server certificate
- Authentication Method: EAP-MSCHAPv2 with Fast-Reconnet enabled
MSCHAPv2 will use the user's AD credentials.
Radius also requires that machine be found in AD. Our CA admin has given me certs to add to the macs for this portion.
I guess I am just very confused as to what info goes where. I've had a look at this:
http://www.revolutionwifi.net/2012/02/mac-os-x-lion-creating-wi-fi-8021x.html
but I still can't figure this out.
Can anyone provide any guidance on setting up 802.1x in this kind of a scenario?
Thanks!

The official documentation is below. I don't know anything that isn't in that document.
http://training.apple.com/pdf/WP_8021X_Authentication.pdf

Having trouble with camera profiles in LR3

Anyone having trouble with accessing the camera profiles from the drop down menu in the develop module/camera calibration section of LR3? The only choice I have is "embedded." After I created a custom with passport color checker it now only offers "profile" as a choice. ANy thoughts?
Thanks,
Tom

Okay, that is different. I have seen a similar discussion in another thread (I think) in the Lightroom forum. It might have been this one. It seems to have been specific to Canon cameras. I don't have an answer. Just one question, however. Are you using standard CR2 files, or are you using the sRaw format? As I was reading the other thread, I was wondering if that could have been part of the problem.

Trouble with color profiles?

Since installing photoshop, I've had no problems. A few days ago, I accedentally hit some hot key which changed some color profile settings, but I can't figure out which ones. Now, when I save a jpg or gif, the colors are much brighter and more vibrant than my working colors. If I turn on the proof colors preview, I get the true image. However, I never had that set before and it doesn't stay set now. Anyone know what's going on? The proof colors are set to "Monitor Colors".
I attached a sample of the same image open in photoshop and the saved jpg image open in Preview. I'd appreciate any help you can give me!

This has been discussed ad nauseam here, and there are many existing threads on the subject. This type of thread can get very long in no time. I suggest you take a look at them.
In a nutshell, you need to calibrate and profile your monitor accurately, select a working color space, honor that tag (color space) in all files you open, and tag all your files with the color profile in which they were created. Then look at the image in a color managed application.
If you choose not to embed the color profile in a JPEG, meaning you end up with an untagged JPEG file, be prepared to see color differences between the appearance of the image in some applications, most especially if you have a wide-gamut monitor. For instance, Photoshop and Firefox 3.0.8 (the latter with color management enabled, which is not by default) will correctly assume sRGB for all untagged images. On the other hand, all Apple applications, from the Finder through Preview, Safari, iPhoto and Aperture, just throw monitor profile at all untagged images. That will produce exactly the effect you show.
Similarly, if you leave an image created in, say ProPhoto RGB, untagged, it will look like it's on fire in Photoshop and Bridge, as well as in the Finder, etc.
To beging learning about color management, start here: http://www.gballard.net/psd/cmstheory.html

802.1x Profile - PEAP/EAP-MSCHAPv2

I'm trying to connect my new retina Macbook Pro to our enterprise network, and am having trouble with the 802.1x profile. Looking at the settings on my Windows PC, I need to use PEAP/EAP-MSCHAPv2, but OSX Lion seems to default to PEAP/EAP-GTC. With these settings, I'm able to connect to the network but cannot access any network resources.
I'm using the iPhone Configuration Utility to generate the 802.1x profile package. As far as I can tell, I am unable to change the inner authentication method with this application. Anyone out there have any suggestions on how I can resolve this?

The prompt is specified when you create the profile on the machine. You can either have the user get prompt for login, save a username and password or use the cache credentials. You need to look at the errors in radius and in the wlc. One will have enough info to say what went wrong during the authentication process.

I am having trouble with my Mac Mini's ethernet connection. Defining a new network interface shows no ethernet adaptor. Reloading SL from DVD repaired. But SL update lost ethernet again. Will Lion Fix?

I am having trouble with my mac mini ethernet. It had been working for weeks after an update to SL 10.6.8.
Once it went out and i repaired it by defining a new connection from System Preferences ->Network->(left panel service, +).
But yesterday, after a power up. my ethernet was not working again. I tried this old trick to repair it, but the interface choices
listed for '+' a new service did not include Ethernet any more. And the Utilities->System Profiler->Ethernet Cards shows
no ethernet available.
As a last ditch effort i reloaded my original SL from DVD. (I think it was version 10.6.4 but i could be mistaken on the version).
The ethernet worked! But KeyNote wasn't going to work because apparently the version i purchased depends on 10.6.8.
So I upgraded again to SL 10.6.8 (Plus some other updates like AirPort which i don't use).
Now the Ethernet is not working again. I see the same symptoms as before with the Ethernet seeming not installed.
Is this a problem seen by others?
Would going to Lion fix the problem?
Could AirPort actually be the culprit and not SL?
If i stay with my original SL, would i need to repurchase a version of KeyNote for the older version of SL?

Have you reset the SMC?
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
While you're at it, resetting the PRAM won't hurt anything and 'might' help is SMC reset didn't work (PRAM does some port control):
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Something else you might try .... you don't say how you're updating to 10.6.8, however, if you're using Software Update, you might try downloading the 10.6.8 combo update, which contains all updates to 10.6. Sometimes, Software Update doesn't work quite right, and installing the combo update fixes that. Download the update from Apple's download site at http://support.apple.com/downloads/ , using Disk Utility repair permissions, apply the combo update, then repair permissions again.

Cannot open your default e-mail folders. You must connect to Microsoft Exchange with the current profile before you can synchronize your folders with your Outlook data file (.ost)

Fresh installation of Exchange Server 2013 on Windows Server 2012.
Our first test account cannot access their email via Outlook but can access fine through OWA. The following message appears - "Cannot open your default e-mail folders. You must connect to Microsoft Exchange with the current profile before you can synchronize
your folders with your Outlook data file (.ost)" is displayed.
If I turn off cached Exchange mode, setting the email account to not
cache does not resolve the issue and i get a new error message - "Cannot open your default e-mail folders. The file (path\profile name).ost is not an Outlook data file (.ost). Very odd since it creates its own .ost file when you run it for the first
time.
I cleared the appdata local Outlook folder and I tested on a new laptop that has never connected to Outlook, same error message on any system.
Microsoft Exchange RPC Client Access service is running.
No warning, error or critical messages in the eventlog, it's like the healthiest server alive.
Any help would be greatly appreciated. I haven't encountered this issue with previous versions of Exchange.

So it looks like a lot of people are having this issue and seeing how Exchange 2013 is still new (relatively to the world) there isn't much data around to answer this. I've spend ALOT of time trying to figure this out.
Here is the answer. :) - No I don't know all but I'm going to try to give you the most reasonable answer to this issue, in a most logical way.
First thing I did when I was troubleshooting this issue is that I ignored Martina Miskovic's suggestion for Step4 http://technet.microsoft.com/library/jj218640(EXCHG.150)because it didn't make sense to me because I was trying to connect
Outlook not outside the LAN but actually inside. However, Martina's suggestion does fix the issue if it's applied in the correct context.
This is where the plot thickens (it's stew). She failed to mention that things like SSL (which I configure practically useless - anyone who ever worked in a business environment where the owner pretty much trusts anyone in the company, otherwise they don't
work there - very good business practice in my eyes btw, can confirm that...) are some sort of fetish with Microsoft lately. Exchange 2013 was no exception.
In exchange 2003, exchange 2007 and exchange 2010 - you could install it and then go to outlook and set it up. And when outlook manual Microsoft Exchange profile would ask you for server name, you would give it and give the name of the person who you setting
up - as long as machine is on the domain, not much more is needed. IT JUST WORKS! :) What a concept, if the person already on premises of the business - GIVE HIM ACCESS. I guess that was too logical for Microsoft. Now if you're off premises you can use things
like OutlookAnywhere - which I might add had their place under that scenario.
In Exchange 2013, the world changed. Ofcourse Microsoft doesn't feel like telling it in a plain english to people - I'm sure there is an article somewhere but I didn't find it. Exchange 2013 does not support direct configuration of Outlook like all of it's
previous versions. Did you jaw drop? Mine did when I realized it. So now when you are asked for your server name in manual outlook set up and you give it Exchange2013.yourdomain.local - it says cannot connect to it. This happens because ALL - INTERNAL AND
EXTERNAL connection are now handled via OutlookAnywhere. You can't even disable that feature and have it function the reasonable way.
So now the question still remains - how do you configure outlook. Well under server properties there is this nice section called Outlook anywhere. You have a chance to configure it's External and Internal address. This is another thing that should be logical
but it didn't work that way for me. When I configured the external address different from the internal - it didn't work. So I strongly suggest you get it working with the same internal address first and then ponder how you want to make it work for the outside
users.
Now that you have this set up you have to go to virtual directories and configure the external and internal address there - this is actually what the Step 4 that Martina was refering to has you do.
Both external and internal address are now the same and you think you can configure your outlook manually - think again. One of the most lovely features of Outlook Anywhere, and the reason why I had never used it in the past is that it requires a TRUSTED
certificate.
See so it's not that exchange 2013 requires a trusted certificate - it's that exchange 2013 lacks the feature that was there since Windows 2000 and Exchange 5.5.
So it's time for you to install an Active Direction Certificate Authority. Refer to this wonderful article for exact steps - http://careexchange.in/how-to-install-certificate-authority-on-windows-server-2012/
Now even after you do that - it won't work because you have to add the base private key certificate, which you can download now from your internal certsrv site, to Default Domain Policy (AND yes some people claim NEVER mess with the Default Domain Policy,
always make an addition one... it's up to you - I don't see direct harm if you know what you want to accomplish) see this: http://technet.microsoft.com/en-us/library/cc738131%28v=ws.10%29.aspx if you want to know exact steps.
This is the moment of ZEN! :) Do you feel the excitement? After all it is your first time. Before we get too excited lets first request and then install the certificate to actual Exchange via the gui and assign it to all the services you can (IIS, SMTP and
there is a 3rd - I forgot, but you get the idea).
Now go to your client machine where you have the outlook open, browse to your exchange server via https://exchang2013/ in IE and if you don't get any certificate errors - it's good. If you do run on hte client and the server: gpupdate /force This will refresh
the policy. Don't try to manually install the certificate from Exchange's website on the client. If you wanna do something manually to it to the base certificate from the private key but if you added it to the domain policy you shouldn't have to do it.
Basically the idea is to make sure you have CA and that CA allows you to browse to exchange and you get no cert error and you can look at the cert and see that's from a domain CA.
NOW, you can configure your outlook. EASY grasshoppa - not the manual way. WHY? Cause the automatic way will now work. :) Let it discover that exachange and populate it all - and tell you I'm happy! :)
Open Outlook - BOOM! It works... Was it as good for you as it was for me?
You may ask, why can't I just configure it by manual - you CAN. It's just a nightmare. Go ahead and open the settings of the account that got auto configed... How do you like that server name? It should read something like [email protected]
and if you go to advanced and then connection tab - you'll see Outlook Anywhere is checked as well. Look at the settings - there is the name of the server, FQDN I might add. It's there in 2 places and one has that Mtdd-something:Exchange2013.yourdomain.local.
So what is that GUID in the server name and where does it come from. It's the identity of the user's mailbox so for every user that setting will be different but you can figure it out via the console on the Exchange server itself - if you wish.
Also a note, if your SSL certs have any trouble - it will just act like outlook can't connect to the exchange server even though it just declines the connection cause the cert/cert authority is not trusted.
So in short Outlook Anywhere is EVERYWHERE! And it has barely any gui or config and you just supposed to magically know that kind of generic error messages mean what... Server names are now GUIDs of the [email protected] - THAT MAKES PERFECT
SENSE MICROSOFT! ...and you have to manage certs... and the only place where you gonna find the name of the server is inside the d*** Outlook Anywhere settings in the config tab, un it's own config button - CAN WE PUT THE CONFIG ANY FURTHER!
Frustrating beyond reason - that should be Exchange's new slogan...
Hope this will help people in the future and won't get delete because it's bad PR for Microsoft.
PS
ALSO if you want to pick a fight with me about how SSL is more secure... I don't wanna hear it - go somewhere else...

Airport Express (Model with 802.11G +54MBPS Mac/PC and Set Up Issues

Hi,
We have a 4 Mac and 1 PC Household. Cable Internet Service by Roadrunner.Cable model (owned) connected to a D-Link 802.11G wi fi router (by ethernet from cable modem)in the family room , then out to a Imac (the half moon base and LCD screen with a airport card also in the family room and the closet computer to the D-Link
router, (we did add a D-Link antenna to the router ? about 10 months ago (a D-Link ANT24-0700 (Version 1.2)and a HP 4 in 1 printer attached via USB to the Imac
,a eMac 1.25 ghz 1Gb ram with airpot card also connected wirelessly (no printer attached on the same floor but in a ajoinging room about 20 feet from the Router, and another eMac 1.0 Ghz 1Gb ram with airport card in the upstairs part of our house (a bedroom) and no issue with Internet connection (it has a Epson 3in 1 printer attached via USB, and a MacBook Pro with 802.11N wireless card in side , bought for a Christmas/Birthday Present and also for college.It to has no issues with the Internet where ever it may be in the house. Our sole PC a HP tower with a added D-Link WDA -2320 Range Booster Desktop Adapter (802.11G) and we added a D-Link Antenna same model as the other a ANT24-0700 to help with Internet access which it did as well as adding some ram to increase page loading time etc. It does not have a printer attached. I will get to the Topic Area now
The Airport Express. I was not involved in the set-up as I was laid up due to a bad back and post major knee surgery , But I always (especially recently) wondered why the light was amber and blinking. I read through the manual and also
Apple.com support and MacFixit.com (which is under construction and moved to part of Cnet.com)and then went to the Airport Express Discussion area (sorry for being so wordy) I need a Twitter account to post!) We have a network name for the D-Link and the computers all were added and it also supports a Xbox 360, a Sony PlayStation 3 and a Nintendo Wi (in online use without issue) but..
A network was also as it appears to myself) for the Airport Express and under the half moon bars showing connection strenght (there is our D-Link network "phoenix" with security protection WPA2 I believe) as I have set up the router, We had a Apple Base station prior that was ? 802.11B (a half moon white unit) still have it in the box ) So for normal daily use, checking e-mail and internet use all of the computers use the "phoenix" or D-Link supported Router 802.11G
and The other network calld Apple Network with numbers and letters after it (and hopefully security) password is unknown , The Airport Express is set up connected via USB to a HP B&W laser printer which has saved quite a bit of money on ink, To utilize that printer you must switch from "phoenix" The D-Link router network to the Apple Network (followed by letters and numbers) The Imac and the eMac in the family room and a ajoing room (after switching to the Apple Network
can than print to the lasr printer. The eMac upstairs and the HP Windows XP Professional software can not print to the laser printer (yet the HP PC shows it as a individual network and a strong signal, equal to the Internet connection from the D-Link, and the eMac (after switching under the half moon (not the proper name I am sure) to get to the Apple Network to print , it will not print, yet it shows a 5 bar signal, same as the D-Link connection. I do believe we have two seperate networks (but do not understand why the two Mac's in the family room can print to the laser printer by simply switching networks and then file and print. ** One other 9probaly major item is that it states to set up the Airport Express with a Mac With OSX 10.4 or later (at the time of set up, we had the Imac and two eMac's all running Panther OSX 10.3.9 9which they continue to have installed) We obtained the HP Tower and Monitor and HP 4in 1 printer ust before Christmas in 2008 and the MacBook Pro in Mid December 2009 (current model and running Snow Leopard 10.6. The HP Tower runs Windows Xp Professional (Service Pack 3) so the MacBook Pro which is much more mobile , could be used to do the set-up, or the HP Tower coulf be moved temprarily, I do recall if Router changes (at least with The D-Link You need to be connected by Ethernet to the Mac
that would be doing the set up/configuration of the router (and it runs OSX 10.3.9 and is a older Mac (with 80Gb Hard drive that is partioned for OS9 and OSX as well , it is under a Ghz processor wise and less than 1 Gb of ram as the last ram slot required a seal to be broken and 256mb of ram (?) could be added
it has 768 mb of ram but knock on wood running well. We use Lacie external drives
on the Imac and both eMac's and need to get external drives for the HP PC as well as the Mac Book Pro (15" screen)
I apoogize if I repeated myself, and rambled but I wanted to (in one post) to explain our set up and network configuration
Questions
1) if indeed it is that the two networks is true and a set yp that is not correct
can the Airport Express be configured without opening up the router (when ever that happens it seems one computer is unable to get online and each time its a differnt one a Mac or veen the PC
The PC under My Computer and Networks clearly shows the wto distinct and seperate netwoks with strong signals and the distance is not far (it is through a floor as the other emac and the PC are upstairs and cabling by ethernet is not a option
2) If I need to open the router would I add the Airport Express as a client as if it was one of the computers or gaming systems on the network? (adding the Mac adress or IP address (not sure how you find the Mac address) and its been while since the router was opened up for any additions or work on it.
3) would it be on the same channel as the router or not ?
4) Hopefully with proper configuration the light will stay on (and green) on the A/E and the eMac and HP PC will be able to print to the laser printer. Currentlt
when anything needs printed from the PC its put on a Flasg Drive and plugged in tothe Imac and the the Apple Network is selected and data printed, The eMac upstairs has the option of using the attached Epson 3 in one or doing the Flash stick work around.
I would be verya appreciative if some one took a look at the set up above and advised me of what is right, what is not right* and what to do to fix things up
I would imagine after proper set up, delete the Apple Network from the PC and eMac upstairs and ? all of the computers as we should have one base station (the D-link and the spoke (the A/E connected by UBS to the A/E (it may be ethernet but the cable connection from the A/E to the HP laser printer is correct (the rest of the A/E set up ... Please , tell me where it is and where it should be
and ? any idea why we can print to the laser printer down stairs and not up stairs ? it did mention printer set up with Panther as possible, page 43 of themanual we have un chaper 5 Tips and Troubleshooting (under whn your printer isn't responding) (we do not have the interfereance listed in the manual,
our phones are land line, one 900 mghz and the others 5.8 ghz
It is possible to move the A/E and laser printer if that would help the two computers (desktops) upstairs) bt the distance is way less than 150 but their is a floor and ? duct work (metal ) but I think here is a place to stop typing and let some of the experts on the discussion forums take a look.
one lst note (as the lap top will be going off to college in the fall (runnning Snow Leopard, and the other 3 Mac's run Panther OSX 10.3.9 should the HP PC windows Xp Professional be the computer to set up the air port express and the Airport Utility proram installed & would this conflict with the current Router (set up by a Macc running OSX 10.3.9 (Panther) i.e (should both set ups be on the same computer?) but actually aThe D-Link is OSX10.3.9 compatible (and 802.11G) and set up requires ethernet connection to a Mac (You type in the numbers and . etc and password as administror and you are in, or should the admin be on the same cpmpuer for the router and A/E ?
(and considering a Airport Extreme Base Station as well as dual frequency simulataneus and 802.11N (for the laptop now) and future, or wait. The 802.11
in theory would broadcast farther..?? even if computers had 802.11b(our Mac Desk tops and the PC 802.11B card
Thanks Again!!!
Many, Many Thanks
amnienttales

William Boyd Jr.
Hello again,
D-Link Router is model DGL-4300 (along with a D-Link ANT24-0700 Omnidirectional
7dbi Antenna . Our Cable Internet ISP (Roadrunner) provides consumers with dynamic ISP address's . All Mac's have Airport Cards and The Hp Tower XW4550 has a D-Link Rangebooster G Desktop Adapter WDA-2320 (also with a D-Link ANT24-0700 Omnidirectional 7 dbi Antenna (the PC OS is Win XP Pro Service Pack 3) The 3 desktop Mac's run OSX Panther 10.3.9 , The 15" MacBook Pro OS is OSX 10.6 Snow
Leopard (not sure what is after the .6 (right now) D-Link's website is
http://www.dlink.com , I have configured this router multiple times in the past.
also added as clients on the network (Utilizing the D-Link Router) are a X-Box 360, Sony Play Station PS3, and a Nintendo Wii all of which have on line ability
and enables online video game play with any one online.
As mentioned prior the Airport Port Express is Model A1084 Part No. M9447OLL/A
which is USB conected to a HP LaseJet B&W , model 1020 and some how the two computers near it can switch to the Airport Express Network from the D-Link Router based Network and print wirelessly to the A/E connected LaserJetPrinter
I realize I will need to reconfigure the D-Link Router and add the A/E as a client. I will try first to use the Airport Utility and see if I can do anything
Utilizing it (adding it to the D-Link network, I think its unlikely but worth a try but* the password is unknown but I have a few guess's as to what it may be.
I do have the necessary admin and network paswwords to cconfigure the D-Link Router,
1) * If the the A/E Utility experiment fails and I need to re-configure the router * do I need to (as per the Airport Express Set Up Guide (Use a Mac with OSX 10.4 or later or a PC with Win Xp Home or Professional (have a desk top PC that has the specs) and The Mac Book Pro meets the Mac Spec's)
If I can not get a password to work on the A/E I would reset it using the reset button
And before plugging in the A/E , connect the appropraite cables in our case a USB cable to the LaserJet Printer then plug in the A/E
2) I would then connect by Ethernet from Either the Mac Laptop or The PC to the D-Link router (if not the router will not set-up correctly)
3) The one question that puzzles me is that we are not using the A/E as a base
but a client
in two sections(Using Airport Express , connecting a Printer via USB
and use Airprt Utility to create a new network or join a new newWireless computers using Mac OSX 10.2.7 (Tiger) or later or a PC with Windows XP and it then goes in to the steps of ising the printer for both a Mac and a PC (using Bonjour on the CD that came with the A/E (this appears to contradict needing to use Mac OSx 10.4 or a PC with Win Xp set the A/E up for use as a printer
(joiing a new network or existig one)
And in Chapter 5 Tips and Roubleshooting= Your Airport Express Status Light Flashes amber & Your Printer is not responding (it is flashing amber and the printer does not respond to the two computers upsstairs (one Mac running OSX 10.3.9 & One PC running WinXp and its states to make sure the printer is selected
in the Printer list o client computers, to do this on a Mac using OSX 10.3 or later , open Printer Set Up Utility and follow steps and if a PC with Windows XP , Open Printers and faxes and then follow steps
in Closing ? can I configure the A/E Utility with a Mac using 10.3.9 as above or
? Per Chapter 1 Getting Started use a Mac with OSX 10.4 or later or a PC with Windows Xp Home or Professional
Perhaps I am taking the tips and trouble shooting and Printer Set up out of context or does the getting Started Computer specs contradict them or are they
for use if the A/E was going to be a Base Station and not a client..
Will keep at it,
ambienttales

Having trouble with Yahoo home page sign in. Some time it brings up my wife's Yahoo log in instead of my log in how can I fix this?

When I open Firefox it is suppose to take me to my Yahoo home page. But it opens up showing my wifes Yahoo sigh in page in stead of mine. Having trouble with Yahoo home page sign in. Some time it brings up my wife's Yahoo log in instead of my log in how can I fix this?

Did your wife tick the box on the Yahoo sign in page to remember her for two weeks?
It would be best two have two separate Firefox profile folders, one for each of you to prevent such problems.<br />
Then you also do not have problems with deleting or changing bookmarks.
* http://kb.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows
* http://kb.mozillazine.org/Shortcut_to_a_specific_profile
* http://kb.mozillazine.org/Using_multiple_profiles_-_Firefox

How can I figure out what my password is and keep it unlocked? Every time I do a system update, it requires the password and sends me into cyber trouble with the remember my keychain access, requiring it every time I log in. A real hassle to be avoided

How can I find out what my password on the computer is? I had to change it due to my teenagers helping themselves, and now every time there is a system update, I have to have the password, which I cannot remember or find. It then wants it every time I log in and pops up Key Chain Access as well. Very annoying. I do not have the disc to reload it and fear I would loose everything on my computer as there is also trouble with the back up system. Too many issues and not enough solutions. Many thanks in advance!

I do not have the disc to reload
Why not? You need your system dvds to troubleshoot & to reset/change passwords in view of your current OS listed in your profile.
You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
If you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number. Here's a list of links to all of those - http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html Another resource: International Support Phone #s.
===============
I have to have the password, which I cannot remember or find.
When selecting passwords, make sure it's one that you will NEVER forget AND no one else can figure out.
Old school--- > Print it out & keep in a safe place. A place that ONLY you know about AND never forget.
New school---> Get a password manager utility. Highly recommend 1Password which is shareware. Do a Google search for free password managers.

Trouble with the Clone Stamp/ Brush Sampling Layer

Hey guys! I've been having trouble with my clone stamp tool. Just installed the new PS CC and when I try to sample the layer that I want to clone, I hit "alt-click" and it gives the the error message telling me to do the very thing I just did? alt-click. Doesn't work. Same problem with the brush tool, except no error message, it just doesn't sample it. Can you help me figure out what the problem is? Thank you!

Update your graphics driver and/ or turn off OpenGL in the prefs and check for flakey color profiles.
Mylenium

Do I need to add a 802.1x profile to allow others to use my wifi?

Before I upgraded to Mountain Lion visiting family members were able to use my internet. Now some cannot even though I have given them my password. Do I need to add a 802.1x profile? Does this mean my router?

I cannot amend my initial post as I incorrectly described the display so here is an update.
As far as I have read and experienced with purchasing two such displays, this model came with a Mini Displayport to DVI adapter not a HDMI to DVI adapter.
I think I need an HDMI to Mini Displayport adapter so I can use the Mini Displayport to DVI adapter that came with the display.
Here is the display:
Apple Cinema Display 23-Inch Aluminum
The Apple 23-Inch Cinema Display (Aluminum) (M9178LL/A), is designed match the Power Macintosh G5 and PowerBook G4 models. It features a 23-inch (1920x1200) wide-format active-matrix LCD display with 16.7 million colors, 170 degree viewing angle, and a response time of 16 ms. It sports dual FireWire 400 and dual USB 2.0 ports on the back of the display.
Picture is here if link is allowed:
http://www.sellyourmac.com/mac-product-guides/cinema-display.html
http://www.sellyourmac.com/images/stories/mac-guides/apple_cinema_display_20_inc h_aluminum.jpg

Satellite 5100/201: trouble with video card or overheat?

Hy,
I'm experiencing trouble with video on a Satellite 5100/201. It seems that when I press on the left side above the graphics card or press a key on the keyboard on that side, the screen starts to be scrambled and vertical lines appear. At the end windows XP resets giving a critical error on the device and the video passes to 640x480. Same thing occurs when running Linux Suse 9.0.
My doubt is what is the cause: the graphics card corrupted or overheating due to the fan not as efficient as originally (my laptop is almost two years old. Did someone succed in finding the cause and resolved the problem, also with the Toshiba assistance?
Any help welcome.

Hi,
I don't think so that Toshiba has problems with the design. You are talking about two different models with two different hardware and for different user profiles!
The 1900 is a Desktop replacement notebook with "desktop" components like processors and the Satellite 5000 is a Multimedia notebook!
Hint: If you had not done it yet, perhaps you could install the graphic card driver once again. If this don't helps, it is the best way to recover the notebook with the Toshiba CD. (this set the notebook to software default settings and the notebook should be work)
Bye Bob

Trouble with 802.1x profile

Similar Messages

Maybe you are looking for