Trunk Problems Between 3500/2950
Hi All,
am trying to create a trunk between a 2950 and 3500. I did the following,
2950:
swsales1(config)#int fasteth0/12
swsales1(config-if)#switchport trunk allowed vlan 1,2,3
swsales1(config-if)#switchport mode trunk
3500:
Ted(config)#int fasteth0/12
Ted(config-if)#switchport trunk allowed vlan 1,2,3
Ted(config-if)#switchport mode trunk
I get the following error on the 3500,
swsales1#
00:14:14: %LINK-4-ERROR: FastEthernet0/12 is experiencing errors
vtp domain for both is the same and the 3500 is the client. Cross-cable between the 2 ports. Cheers.
EDIT: no shutdown was issued on both interfaces.
coolboarderguy...
Hi All,
funny you should mention the switchport nonegotiate command, as neither switch would accept it. I found it strange, as this lab,
http://delivery.monsoon5.com/delivery/Launch?sessionid=11226191797360000000002498dbc625852e04cf48362eac105604dd96818a5
uses it and the lab states that it used 2950 and 3500(3550) switches. Cheers.
coolboarderguy...
Similar Messages
-
Router 2811 and C2960 Switch Trunking Problem
Hi all
I got an problem with a trunking problem between Router 2811 and C2960 switch
In router 2811 - I created f0/0.1 10.65.20.1 (VLAN 1) and f0/0.48 10.65.23.1 (VLAN 48)
In C2960 - Vlan 1 10.65.20.30 , VLAN 48 10.65.23.30
Finally I can only ping VLAN 1 IP but fail to ping VLAN 48 IP, can help me how to troubleshoot it?
Hugo
Router 2811 Configuration:
interface FastEthernet0/0.1
encapsulation dot1Q 1 native
ip address 10.65.20.1 255.255.255.0
interface FastEthernet0/0.48
encapsulation dot1Q 48
ip address 10.65.23.1 255.255.255.0
C2960 Configuration:
interface FastEthernet0/24
switchport mode trunk2811#sh vlans
Virtual LAN ID: 1 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: FastEthernet0/0.1
This is configured as native Vlan for the following interface(s) :
FastEthernet0/0
Protocols Configured: Address: Received: Transmitted:
IP 10.65.20.1 388873 262275
Other 0 1723
390760 packets, 71854310 bytes input
263998 packets, 53723195 bytes output
Virtual LAN ID: 48 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: FastEthernet0/0.48
Protocols Configured: Address: Received: Transmitted:
IP 10.65.23.1 0 0
Other 0 20
0 packets, 0 bytes input
20 packets, 1883 bytes output
2960_24#sh int trunk
Port Mode Encapsulation Status Native vlan
Fa0/24 on 802.1q trunking 1
Gi0/1 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/24 1-4094
Gi0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/24 1,48
Gi0/1 1,48
Port Vlans in spanning tree forwarding state and not pruned
Fa0/24 1,48
Gi0/1 1,48 -
Problems between an UC520 and Asterisk with sip trunk
I have an UC520 and Asterisk with a sip trunk created between them, the calls from the UC520 to the Asterisk are ok, but the calls form de Asterisk to the UC520 are always busy.
Logs from the asterisk show that the first part of the call is ok, but the call is not complete, this means that the part where the extensions are with @ipuc520 doesn't appear
I created a sip trunk from de CCA 1.9 and it puts this for incoming calls for the dial peer, if I compare with a CCME, there is no configuration for incoming call there
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Tabla normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:Calibri;
mso-fareast-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;
mso-fareast-language:EN-US;}
dial-peer voice 1000 voip
permission term
description ** Incoming call from SIP trunk (Generic SIP Trunk Provider) **
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
session protocol sipv2
session target ipv4:x.y.z.w
incoming called-number .%
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
And there is no configurarion at all that could block the calls
The x.y.z.w was the sip server ip (asterisk ip)
The comminication between sip and h323 are allowed in the four ways
The allowed codecs are g711ulaw and g729r8
Asterisk is working now with other CCME and they are ok so I copied the configuration from those CCME to the UC520 and from the other sip trunks in asterisk the new trunk sip for uc520
The sip trunk created from the CCA was replaces for the one from the CCME that is working now
The routes are ok in Asterisk.
There is no translation profile in incoming calls.
There is no ACL applied in all configuration.
There is no log about callres incoming from the asterisk.
Could anyone halp me pls?Hi Rina,
Help me to try and understand what you are trying to do.
In this code snippet i see the following:
001808: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Calling Number=7129, Called Number=7129, Peer Info Type=DIALPEER_INFO_SPEECH
001809: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Match Rule=DP_MATCH_DEST; Called Number=7129
001810: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Result=Success(0) after DP_MATCH_DEST
001811: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
Result=SUCCESS(0)
List of Matched Outgoing Dial-peer(s):
1: Dial-peer Tag=20036
This looks as though you have a call coming in from the Asterisk system to number 7129, which then leads to this according to the config file you provided.
number 7129
label 7129
description7129
name 7129
call-forward busy 6001
call-forward noan 6001 timeout 10
Which at this point I am going to assume this is ephone-dn 10 (Please confirm). If this is the case then the inbound call is being matched correctly to a DN (Which has its own dial-peer tag "Dial-peer Tag=20036".
But then i see this:
001817: 1w3d: //-1/55940098BA19/DPM/dpAssociateIncomingPeerCore:
Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1000
001818: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=Unknown, Called Number=, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
001819: 1w3d: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=NO_MATCH(-1) After All Match Rules Attempt
So the incoming call has been matched to Dial-peer 1000 which is an incoming VoIP dial-peer:
dial-peer voice 1000 voip
permission term
description ** Incoming call from SIP trunk (Generic SIP Trunk Provider) **
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
session protocol sipv2
session target sip-server
incoming called-number .%
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
But then can see it has no where to go. So either I am reading this all wrong and the 7129 number is a result of another call taking place whilst you were debugging the system, or it is part of the debug and I am missing something here.
Rina, just so I understand this all. Are you trying to do WAN type calling from one system UC-500 (System "A") to the Asterisk system ( System B) and same? And so far calls going from the UC-500 to the Asterisk system are fine, but calls coming in from the Asterisk system to the UC-500 are not?
What happens on the Asterisk side when you try to call an Extension on the UC-500, do you get any ringing? Or is it a fast busy tone?
I am going to look over your configuration and debug a little further when I get home, maybe I am missing something here and can identify it.
Cheers,
David. -
I have a network design issue to solve and need some help. Current network uses ISL to trunk vlans between two sites. Some encryption devices need to be installed that do not understand ISL (or BPDUs for that matter). I need to split the ISL, or tunnel it, so that the inside devices cannot see the L2 stuff but the end devices can still communicate. Any ideas?
Regards ... JohnHi Josh
I had to solve a very similar problem to yours, and the solution I came up with was to use L2TPv3 (layer 2 tunnelling protocol) over IPSEC. I used the same device (a pair of old 1700 series routers at each end) to create both the L2 tunnel and the IPSEC tunnel, but in your case you are using a separate device to do the encryption. You just need to create the L2 tunnel between 2 devices which are on the unencrypted side at each end. You need to ensure that the 2 devices can route to each other. -
Trunk config between two 6500 cat switches
Hi All,
What is the recommended trunk configuration between 2 cisco 6500 switches including hsrp scenario.
ThanksHi Samir,
In almost all scenarios, its recommended to have 'dot1q' encapsulation and a static trunk config 'switchport mode trunk'. Matching the native VLAN on both sides is required and will be VLAN1 by default.
When configuring trunks, you should be mindful of VTP, trunk and STP states. Reviewing the following for mismatches between your Cat6K will help:
- show vtp status
- show interfaces trunk
- show spanning-tree
In terms of HSRP, it is also recommended to run HSRP active in the same location as STP Root to avoid any asynchronous routing problems.
/ijay -
Communication problem between NetBeans and Tomcat
hi!
i got a quite mysterious problem. here is what happens:
- i start NetBeans 5.5.1 (the first time)
- i want to debug my JSF-Project, the Debugger starts
- After a few seconds the debugger waits for tomcat (it sais: "Waiting for Tomcat...") and tomcat starts
- Again after a few seconds the tomcat-debugger-output sais "Tomcat startet in 3333 ms".
okay.
when i enter http://localhost:8084/ in my browser i get the tomcat homepage, so the server has definitely started! But nothing happens in NetBeans and nothing happens with my project....
In the lower-right corner i see this blue working-bar that sais "deploying project" but nothing happens. The Project-Debugger-Output still sais "Waiting for Tomcat..." but nothing happens...
And after something around 3 minutes (i guess it's a timeout) i get the error "Starting of Tomcat failed." But is HAS started, i can login to the Administration-Area in my browser!
so i guess there is a communication problem between netbeans an tomcat. Netbeans waits for a message from tomcat but tomcat doesn't send it..or netbeans doesn't understand it.
But the story goes on:
When i press the debug-button a second time it takes only a few seconds till i get the message: "Tomcat server port 8084 already in use". OF COURSE! Because Tomcat has already startet and can't be stoped by NetBeans.
i'm trying to solve this problem for 4 days now, so i would be very happy if anyone has an idea where to start/continue the search...
thanks,
flo.
some system-info:
- windows vista business 32-bit
- no firewall is running
- AntiVir Personal Edition IS running
- Yahoo Widgets Engine IS running
- no other software is running
and finally the tomcat-log:
Using CATALINA_BASE: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base
Using CATALINA_HOME: C:\Program Files\NetBeans\enterprise3\apache-tomcat-5.5.17
Using CATALINA_TMPDIR: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base\temp
Using JRE_HOME: C:\Program Files\Java\jdk1.5.0_12
Listening for transport dt_shmem at address: tomcat_shared_memory_id
21.09.2007 18:27:50 org.apache.catalina.core.AprLifecycleListener lifecycleEvent
INFO: The Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: C:\Program Files\Java\jdk1.5.0_12\bin;.;C:\Windows\system32;C:\Windows;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Program Files\QuickTime\QTSystem\;C:\Program Files\ThinkPad\ConnectUtilities;C:\Program Files\Common Files\Teleca Shared;C:\Program Files\Common Files\Adobe\AGL;C:\Program Files\MySQL\MySQL Server 5.0\bin;C:\Program Files\cvsnt;
21.09.2007 18:27:50 org.apache.coyote.http11.Http11BaseProtocol init
INFO: Initializing Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:50 org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 1862 ms
21.09.2007 18:27:50 org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
21.09.2007 18:27:50 org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.17
21.09.2007 18:27:50 org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
21.09.2007 18:27:53 org.apache.coyote.http11.Http11BaseProtocol start
INFO: Starting Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:54 org.apache.jk.common.ChannelSocket init
INFO: JK: ajp13 listening on /0.0.0.0:8009
21.09.2007 18:27:54 org.apache.jk.server.JkMain start
INFO: Jk running ID=0 time=0/31 config=null
21.09.2007 18:27:54 org.apache.catalina.storeconfig.StoreLoader load
INFO: Find registry server-registry.xml at classpath resource
21.09.2007 18:27:54 org.apache.catalina.startup.Catalina start
INFO: Server startup in 3626 msAs i wrote before, the same problem occured for me. I have found a solution which is : Go to tools menu and then select options . In the proxy info, select No Proxy.
I hope this help you -
ASA 5505 Trunking problem with cisco 3760
Here is my asa 5505 configuration and at bottom i am pasting cisco 3760 configuration, I am having trunking problem and seen other people having the same issue but no solution.
Problem: when i connect any device on Switch 3760 port 1 which is trunked i cannot communicate with niether vlan.
I have tried device with both static vlan configuration
192.168.1.99 (vlan 2)
172.168.1.99 (vlan 8)
if i change port 1 to access mode or define native vlan it work with one vlan.
interface 5 of Cisco ASA is connected with interface 25 (uplink) on Cisco Switch
interface Ethernet0/5
switchport trunk allowed vlan 1-10
switchport mode trunk
interface GigabitEthernet1/0/25
description **UPLINK**
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
switchport mode trunk
On port 1 of cisco Switch i am creating trunk
interface GigabitEthernet1/0/1
description **LAN**
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
switchport mode trunk
no logging event link-status
spanning-tree portfast
CISCO ASA Config i have configure the following vlans
interface Vlan2
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan8
description Server VLAN
nameif Internal_LAN
security-level 90
ip address 172.168.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
on Cisco 3760 i have configure the following vlan.
v
vlan 2
name inside
vlan 8
name Internal_LAN
interface Null0
no ip unreachables
Message was edited by: macboyHello,
I can see many people have visited the post but there isn't any reply.
I think this is because of the following:
The configurations are long and most people dont want to read it. Try adding only relevant configuration to the issue.
The problem description is not clear. You mention trunking problem but what exactly is the problem? Can you ping from switch to ASA? Is any Vlan information being passed or they are all failing. Try to be as much specific as possible.
Which port of the switch connects to the ASA?
Using portfast on a trunk (interface GigabitEthernet1/0/1) is not recommended.
Regards,
Felipe.
Remember to rate useful posts. -
Problems between Xcelsius and WebDynpro for Java
How should I do to show Xcelsius in WebDynpro for Java?
How should I transport data between Xcelsius and WebDynpro?
How should I control WebDynpro with Xcelsius?For example,firing plugs in Xcelsius like in WebDynpro to change one view to another.
How should I do to execute a Java method in Xcelsius?For example,scheduling a job on clicking a button in Xcelsius.
Besides these,I also want to know the same problems between other BOE contents and WebDynpro for Java.
Regards,
AbeHi Pradeep:
Well that purely depends on the business application (project) your client is proposing. Following are very few factors which will drive for creating web-based applications:
VC: it's a UI modeling tool (non-programming) for creating rapid creation of web-based applications.
WD: its a powered by Java and ABAP with which you can create robust business applications.
If your client is very choosy about rapid application development, reporting, rich user interface, to reduce TCO then VC is the choice. Or if the project contains typical integration with SAP and non-SAP systems, complex business logic development, integration with WCM systems...etc then WDJ is the option.
If youve some sort of custom development with facilitating the Development Infrastructure (NWDI) then WDJ is the only option I could say.
We hope with NW CE 7.1.1(referred by Priyanka Singh) tighter integration between these TWO tools may over come the ambiguity of using them.
Tnx,
MS -
do any of you experience Im having with my ipad? I can't make a comment in Facebook for older posts and I can't open numerous comments from old posts of my friends. but everything works perfectly when I use my laptop(non-apple). is there problem between apple and FB?
Facebook apparently has their site coded poorly for tablets with touch screens. Try using the Facebook app. It is not perfect either but it is better than view in a browser lately.
-
Can I use straight cable to connect trunk ports between 2 switches?
Hi,
Am I able to use straight instead of cross cable to connect trunk ports between 2 switches??
thanks!Hi Devang,
When a 10/100 Fast Ethernet interface is enabled, one end of the link must perform media dependent interface (MDI) crossover (MDIX), so that the transmitter on one end of the data link is connected to the receiver on the other end of the data link (a crossover cable is typically used).
The Auto-MDIX feature eliminates the need for crossover cabling by performing an internal crossover when a straight cable is detected during the auto-negotiation phase.
HTH, if yes please rate the post.
Ankur -
Hi,
I am having a sync problem between my iPhone/iPad and Outlook calendar events (Outlook 2010).
Here is the description of the problem:
1. In Outlook - please create a new event/appointment (e.g. "Test").
2. Reminder is set by default to 15 minutes. You can change it by using a dropdown menu - please select: "0,5 days".
3. Click on "0,5 days" and change it manually to "14,5 days".
4. Click on "Save & Close".
5. (Do not snooze or dismiss the reminder.)
6. Sync with your iPhone/iPad.
7. Open this new event on iPhone/iPad - you can see that alert is set to "15 minutes before" instead to a correct value that was set in Outlook.
The same problem can be seen if you set the reminder to e.g. "3 weeks" (standard value is "2 weeks").
However, it is interesting that non-standard values like "1,5 days" (and all other until "13,5 days") are synced without any problem.
Does anyone have a solution how to solve this problem (different than the trivial solution of not using those strange values)?
Thanks!Thanks to another post (https://discussions.apple.com/message/17501071#17501071) I reset the sync history, here is what to do:
Launch iTunes.
Before you hook up your iPhone to the PC and iTunes do this: Go to iTunes Edit menu > Preferences… > select the iPhone > click the Reset Synch History button > click OK.
Connect the iPhone to the PC and let iTunes recognize it.
In the top right corner is the iPhone icon, click on the left side of the iPhone icon > the iPhone menu launches.
In the menu along the top click on Info > make your selections > click Sync button > it gives you a dialog at the top with the steps it’s going through during the sync.
In the top left of the iTunes app > click Exit. -
I have connection problems between the mini ipad and my powerbook g4, you are not allowed to see or share applications.
That is not possible.
-
I have a drawing that was resized to a certain length using PE4. I have now upgraded to PE10 and when I print the drawing , it prints 3-4 times larger than what it should be. When I view the drawing, the ruler at the top of the screen shows it being the correct length and when I checked the deminsion in the resize box, it also has the correct length. Have I done something wrong or should I delete the drawing and start over from scratch?
Could you be a little more specific please? Sorry, I am not a tech guy just a poor laymen.
Date: Thu, 2 Aug 2012 20:30:55 -0600
From: [email protected]
To: [email protected]
Subject: Problems between PE4 and 10
Re: Problems between PE4 and 10
created by photodrawken in Photoshop Elements - View the full discussion
Check your PSE print settings, especially the DPI value in the "Print Quality". Ken
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4595437#4595437
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4595437#4595437. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Photoshop Elements by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
I use itunes on a Dell XPS502 with W7/64. In some cases have have problems to import CD's. The sound is very disturbed and the import need a lot more time than in normal cases. Is there a problem between itunes and W7/64 or a known hardware issue?
Example-CD : "Tracy Chapman , Telling stories" is not able to import . I have more such negative cases. But in other cases it works fine and the sound is great.
The firmware at the inbuild CD/DVD DS-6E2SH is the latest version.
What can I do??hi b noir,
I don't no about virtuel drives like you mententioned. In the mean time I have rebooted the XPS and run again the iTunes diagnostics. I think the back - chance in the registry was not ready to use. Now there are another results. They are the same in case of a running CD or a not running CD. The difference in total is like before. It takes more time that iTunes reads the (bad) CD and at the there is no good sound. In both cases ( running or not running CD) iTunes diagnostics gives as a result :
(the copie from ITunes shows the result of the not running CD from Tracy Chapman)
Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
Dell Inc. Dell System XPS L502X
iTunes 10.3.1.55
QuickTime 7.6.9
FairPlay 1.11.17
Apple Application Support 1.5.2
iPod Updater-Bibliothek 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Treiber 1.55.0.0
Bonjour 2.0.5.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes-Seriennummer 00D7B2B00CD25750
Aktueller Benutzer ist kein Administrator.
Aktuelles Datum und Uhrzeit sind 2011-06-11 19:33:22.
iTunes befindet sich nicht im abgesicherten Modus.
WebKit Accelerated Compositing ist aktiviert.
HDCP wird unterstützt.
Core Media wird unterstützt.
Info zu Video-Anzeige
NVIDIA, NVIDIA GeForce GT 540M
Intel Corporation, Intel(R) HD Graphics Family
**** Info für externe Plug-Ins ****
Keine externen Plug-Ins installiert.
iPodService 10.3.1.55 (x64) arbeitet zurzeit.
iTunesHelper 10.3.1.55 arbeitet zurzeit.
Apple Mobile Device service 3.3.0.0 arbeitet zurzeit.
**** CD/DVD-Laufwerkstests****
LowerFilters: PxHlpa64 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.2.0.1),
D: PLDS DVDRWBD DS-6E2SH, Rev CD11
Audio-CD im Laufwerk
11 Titel auf der CD gefunden, Spieldauer: 42:07 auf Audio-CD
Titel 1, Startzeit: 00:02:00
Titel 2, Startzeit: 03:59:47
Titel 3, Startzeit: 07:19:27
Titel 4, Startzeit: 11:31:30
Titel 5, Startzeit: 15:31:50
Titel 6, Startzeit: 20:07:50
Titel 7, Startzeit: 24:27:15
Titel 8, Startzeit: 27:49:10
Titel 9, Startzeit: 32:41:25
Titel 10, Startzeit: 35:29:65
Titel 11, Startzeit: 38:38:00
Audio-CD erfolgreich gelesen (Suche nach alter Firmware).
Laufwerksgeschwindigkeit erfolgreich erkannt
Die CDR-Geschwindigkeiten des Laufwerks sind: 4 10 16 24
Die CDRW-Geschwindigkeiten des Laufwerks sind: 4
Die DVDR-Geschwindigkeiten des Laufwerks sind: 4
Die DVDRW-Geschwindigkeiten des Laufwerks sind: 4
After starting the import it is going slower and slower. If it is helpful I can send you a soundfile with these distortions.
best regards
tcgerd -
Problem between SOAP Sender and JDBC Receiver
Hi,
I have a asynchronous scenary between SOAP Sender and JDBC Receiver.
The idea is sending an ID for updating one register.
Table structure is:
TABLE AS_PERSONA
(P_RUT VARCHAR2(10) NOT NULL,
P_NOMBRE VARCHAR2(50),
P_APELLIDO VARCHAR2(50))
The ID is the P_RUT field.
The structure of message that I send by SOAP, is the following:
<SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<SOAP-ENV:Body>
<m:MT_CONS_SOAP xmlns:m="urn:prueba:voliva">
<CONSULTA>
<P_RUT>15445</P_RUT>
</CONSULTA>
</m:MT_CONS_SOAP>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
The JDBC receiver structure is:
<?xml version="1.0" encoding="UTF-8"?>
<ns0:MT_CONS_PERSONA xmlns:ns0="urn:prueba:voliva">
<Statement>
<AS_PERSONA action="UPDATE">
<table>AS_PERSONA</table>
<access>
<P_NOMBRE>DELETE_BY_XI</P_NOMBRE>
<P_APELLIDO>DELETE_BY_XI</P_APELLIDO>
</access>
<key>
<P_RUT>15445</P_RUT>
</key>
</AS_PERSONA>
</Statement>
</ns0:MT_CONS_PERSONA>
When I do a call to SOAP by XMLspy, it returns a message without data, that means succesfull reply.
I see message monitor and see the succesfull flag. But in the database it doesn't update the register.
This scenario was proved using the File Sender and same JDBC Receiver, then result was succesfull.
I proved SOAP Sender with a File Receiver, storing information from SOAP sender in an archive, and works well.
Then I imagine that exist some problem between SOAP and JDBC. what could be happening ?
Thanks.Hi,
Looks like the problem is with the JDBC receiver...try updating the value in the table by using a File-JDBC scenario..does it work..check the adapter monitor in RWB..
Regards,
Sushumna
Maybe you are looking for
-
Both the device and the reformatted computer are linked to my sync account, but while the device has all my bookmarks, the computer is empty. I synced and re-synced and did the whole backup-restore thing, but nothing. I don't want to do something tha
-
No changes appear when batch editing Camera Raw Files and saving as jpegs
When I batch edit my raw files, including saving the file as a jpeg, from bridge or photoshop the resulting file saved never includes any changes I made in the Camera Raw editor. For example if I have lightened the photo by changing the exposure in C
-
Sql loader failed on an import a 257 char column
I was running a sqloader which has one column that is define at 2000 VARCHAR2, but the data getting inserted that column was only 256, which worked - but at 257 or above characters it would fail Thx...
-
Hey, I just build a new website and it doesn't show up in the Google results. I was wondering if anybody could help me out. The website is www.schoorlsebokkentocht.nl , and when I search "Schoorlse Bokkentocht" it doesn't show. In the Megadata all th
-
I am trying to Bluetooth my ps3 to my ipad2 and it recognizes the device but then asked me a pass key on my ps3. What would pass key be or what is pass key?