Two ISP connection and 4 NIC

I have two ISP connections for Internet and the BM server has four
interfaces, two public interfaces with completely different IP addresses
and two private interfaces.
I want to connect two different Terminal Server one for each ISP
connection.
When I connect to the public side of the server, I can only connect
to the public IP address that is in the same subnet as the default route
uses.
Thank you

In article <HwTIi.1699$[email protected]>, Valentin wrote:
> When I connect to the public side of the server, I can only connect
> to the public IP address that is in the same subnet as the default route
> uses.
>
That is correct.
This one gets tricky, because of routing issues. If you know NAT, you
might be able to enable dynamic NAT on the private (LAN side) of one of the
internet routers. That will make all traffic coming in that way look like
it comes from a local address, and the second NIC will respond to it.
Otherwise, all traffic will end up going to the default route. You may
need filter exceptions to allow such traffic to go between public NIC's, if
it works at all.
If you just want to RCONJ to the second public NIC, you might be able to
configure static NAT of that address to itself, but the default route and
filters are still going to give you grief.
You might want to look at tip #51 at the URL below, for a system with 2
subnets on one public NIC.
It sounds to me like you need a dual-WAN router to handle the two ISP
connections. I've set up a number of servers that way using inexpensive
Xincom routers (www.xincom.com).
Craig Johnson
Novell Support Connection SysOp
*** For a current patch list, tips, handy files and books on
BorderManager, go to http://www.craigjconsulting.com ***

Similar Messages

Is there a cable with two Apple connections and one USB connection?

Is there a cable with two Apple connections and one USB connection?

it would be possible without damage to the phones if only the charging pins was used
but it would mean the 2 phones would charge 1/2 as fast as normally

How set up Airport to connect Mac to isp connection AND play music and print?

I used to have an AX wifi in the house with which I surfed, printed and played music.
My isp recently installed a new modem/wireless router in my home. I now have lots of great speed but they couldn't help me retain the ability to send print jobs and music to my (2nd generation) AX base station.
I know I'm going to have to do a hard reset of my AX to clear out the mess I've created in Network configurations trying to get things working. But once the slate's been cleared, I still don't really have a clue about "creating new networks" vs "extending" existing ones etc etc...
Can anyone assist me to set up a freshly reset base station to "piggy-back" on my new isp's wifi network for printing and music purposes? Or perhaps recommend/pass along an article or other reference source that would assist me in doing so?
Rich

AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup >Music
Enable AirTunes (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

Two Asa Two Isp and Windows 2008 R2 Server

Hello Everybody ,
If you can support my issue , I do appreciate a lot.
First of all thanks a lot for your interest ..
Here is my issue :
I have two Isp Connection ( 1 metro Eth Connection and 1 Ghdsl Connection )
1) Asa 5505 (Version 8.0(5)) is for the 1.st Isp Connection
Windows 2008 R2 server is up and running as Web Server on this ASA 5505 config.
As:
(static (inside,outside) mywebsrv.mycompany.com 192.168.5.5 netmask 255.255.255.255
And Ipconfig of W2008Srv is 192.168.5.5 255.255.255.0 192.168.5.1 (Gateway ASA 5505)
2) Asa 5510 (Version 8.0(5)) is for the 2.nd Isp Connection
Windows 2003 R2 server is up and running as Ftp Server on this ASA 5510 config.
As:
(static (inside,outside) myftpsrv.mycompany.com 192.168.50.10 netmask 255.255.255.255
And Ipconfig of W2003Srv is 192.168.50.10 255.255.255.0 192.168.50.1 (Gateway ASA 5510)
Here is my question :
I need to move my Ftp server (due to old hardware + old server issues )
into the Windows 2008 R2 Server ( HP DL Server with 4 Nic).
If I conect my Asa 5510 to the second nic of Windows 2008 R2 Server.
and give an ip address as 192.168.50.10 255.255.255.0
what should be the gateway Ip address : ?
Before I go ahead and implement :
a) What do I need to do on the Windows 2008 R2 Server
as persistent route adds with different metrics
b) Any config adds or changes on Asa 5505 and ASA 5510 regarding static routes with
different metric and so on ...
Many thanks in advance for your support .

If you do that, the second interface will work as a failsafe for the first NIC.
As far as i know, you won't be able to route traffic based on the type of traffic nor do load-balancing between the interfaces.
I guess the best approach will be to get a newer server and use it as a replacement for the one running 2003 R2.

NAT and Routed Network with Two ISP's on one router

I'm sure this has been done covered many times, but I am not finding it.
I have two ISP connections.
With ISP-A I have a /30 between us and 200.100.100.0/24 is routed to me via the /30 for thsi example we will say the /30 is 1.1.1.1 on isp end and 1.1.1.2 on my end
With ISP-B I have a 100.0.0.0/29 subnet. and the ISP gateway is on that subnet at 100.0.0.1
On the inside of my network I have devices using both 200.100.100.x addresses and devices on 192.168.100.x that need to use NAT.
I would like all of the devices on 200.100.100.x addresses to continue using ISP-A as their gateway.
Everything on 192.168.100.x should use NAT and go out ISP-B
I have tried
ip nat inside source route-map ISP-A interface GigabitEthernet0/1 overload
route-map ISP-B permit 10
match ip address 101
match interface GigabitEthernet0/1
set ip next-hop 100.0.0.1
route-map ISP-A permit 10
match ip address 111
match interface Multilink1
set ip next-hop 1.1.1.1
The problem comes when I have default routes to ISP-A in the router than none of the ISP-B traffic works, and vice versa.

I think for this to work correctly and be able to split traffic between the 2 ISPs, you would need to use BGP, because default is going to use one ISP or the other.
If you can use BGP, this link will help you in load shearing between multiple ISPs when you have one router.
http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html#conf4
HTH

Firefox glitch and hang up my isp connection

Firefox start to glitch, page load as a blank page, new tab load as a blank page also ff hang up my isp connection and the only way to fix the glitch is rebooting the pc, any advice whould be good

It got so bad this evening firefox was crashing every five minutes. I finally took time out and started moving everything to chrome.
I have been a loyal user since the days of netscape and I hope I'm not bidding firefox a sad farewell :(

Multiple ISP connection on TMG

Hi, guys
We have three ISP connections. How could I configure to control relevant traffic go out via relevant ISP connection?
Nice Day

Hi,
Based on my knowledge, TMG cannot support more than two ISP connections. Meanwhile ISP redundancy can only help you load balance but not select routing path.
http://technet.microsoft.com/en-us/library/ee796231.aspx#ISPRedundancyIssues
Best Regards
Quan Gu

Hackers and USB NIC

I've taken on a new client and have inherited a mess. Far beyond what I'm about to describe.
This is a network of over 20 Macs and a Mac mini with OS X server.
Upon my first visit at this location I discovered the Mac mini server's built-in NIC had failed, and to corect this the prior IT person had set up an Apple USB 100-BT NIC for the LAN. He had also set up another Apple USB 100-BT NIC with a direct-connect to the internet via a public IP, bypassing the Cisco firewall.
Don't ask why. ;-)
This second NIC with the direct connect has burned out 4 times so far. I firewalled it yesterday.
However, by reading through Console logs I did discover that hackers were trying to intrude via that NIC. The logs were flooded with thousand upon thousands of entries for this hacker activity - every single day.
Does anyone think this hacker activity was responsible for the burned out NICs? Each time the USB NIC would burn out there would be massive amounts entries in the Console logs for the hacker activity.
If someone were to have asked me if it were possible to burn out a USB NIC like this I'd say unlikely. But it sure does explain this nicely.

There are a variety of folks that are always trying to access Internet-connected systems and for various purposes, and that's part of the Internet environment, and it's why I usually recommend a server-grade firewall for configurations running OS X Server and server-oriented computing. Having a directly-Internet-connected server is more effort and more risk than its worth, in my experience.
Electrical grid control to the level of an Ethernet uplink is not typically available to the nefariously-inclined.
All that written, I'd expect there's a wiring problem with the upstream Ethernet connection, and the NIC is receiving excess voltage, or possibly a grounding or voltage problem with the system and its power source or other system external wiring components that's being grounded via the NIC connection. This can include nearby lightning, general grounding and wiring faults and floating grounds, interference or electric surges from unusual or large-amperage local devices, and related issues. Too much power arriving via the NIC that burns it out, or too much power departing via the NIC that burns it out. These repeated faults are usually environmental, and not usually triggered by the nefariously-inclined.
You can check with an electrician, and particularly one with some low-voltage experience. The electrician may suggest monitoring the voltages at the system and at the network and there are tools available to do that, or might suggest surge suppressors or capable less-interruptible power supplies (LIPS, they're never truly uninterruptible), or some combination.
In my experience, simply replacing burned-out components isn't a viable long-term fix for power surges and over-voltages and grounding issues.
It's also possible that there's somebody locally that's accidentally or intentionally introducing voltages or surges where they shouldn't. Phone line connections don't mix all that well with Ethernet connections, for instance.

How can I use Balancing, if I connected to two ISP?

Hello,
I have NetWare6sp3 with 3 NIC's and connected to two ISP. I set two default
gateways (One to first ISP, Another to second ISP). But all of trafic goes
via first gateway. Can I use Balancing beetween ISP1 and IPS2?
Maxim Cuznetov

Maxy,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Best Practice Two ISPs and BGP

Hello Experts.
I was wanting to hear opinions for the best way to setup two ISR4431's with two 2960x's and two ASA firewalls.
My current design is:
ISP1 router -> ISR4431-A ->{2960x pair} -> ASA-A
ISP2 router -> ISR4431-B ->{2960x pair} -> ASA-B
Currently using public BGP and HSRP on the inside with an SLA monitor to a public IP.
If HSRP is the best way to accomplish this, how do i solve these two problems or is there a better design? (The two 4431's are not connected to each other currently.)
-Least Cost routing (i guess that is what its called) - I want to visit a website that is located on ISP2's network (or close to it), but HSRP currently has ISP1 as active. If i go out ISP1 it may go around the country or 10 hops before it hit a site that is 4 hops away on the other ISP.
-Assymetric routing - i think that is where a reply comes in the non-active ISP - how do i prevent that.
I am really just looking for design advice about the best way to use this hardware to create as much redundancy as possible and best performance possible. If you could just share your opinion of "I would use ____" or give me a stamp of reassurance on the above design and any opinion on the two problems.
Thanks for the time!

Hi,
If you are running BGP with the service provides, you need an IBGP link between the 2 ISR-4431 routers. If for example you want traffic to go out using sp-1 and come back using the same provider you need to us AS path prepending, so sp-2 sees a longer path to your network and so traffic goes out and comes back through the same provider. In this case you use sp-2 as backup link, if not you can be dealing with Asymmetric routing. In addition, for HSRP/VRRP to work both routers should be connecting to the set of 2960x switches. You can simply stack the 2960x switches so they logically look as one device. The same should go for the firewalls. They should connect to the switch stack.
HTH

Currently I have two iPads connected to the same Apple ID and one connected to Game Center. I want to connect the second iPad to Game Center so that I do not lose my progress on apps like Clash of Clans.

Currently I have two iPads connected to the same apple iPad. One is connected to game center(iPad air) one the other(iPad 2) is not connected to Game Center. How can I connect the iPad 2 Clash of Clan progress to game center when I already have another clash from iPad air connected?

You cannot transfer content between two accounts. The sooner you make the conversion, the better. Just pick the new one and start using it(buying music etc).
*A lot of people open new accounts when their email changes or they have a new email. You can just access your apple id account and change the primary email that you use to log in along with other details.

I own a 13-inch MacBook Pro and for the past day, my wifi on my laptop says I only have two bars of connection and is running very slow,but all of my other devices such as my iPhone and iPad are connecting perfectly to the wifi. How can I fix this? Thanks

I own a 13-inch MacBook Pro and for the past day, my wifi on my laptop says I only have two bars of connection and is running very slow,but all of my other devices such as my iPhone and iPad are connecting perfectly to the wifi. How can I fix this? I have tried to shut my laptop off and let it rest and I have also re-started my wifi router three different times. Someone please help me with this problem so I can begin to use my laptop again as I take it to school and use it for class.
Thanks so much!

FCP, and all software on OSX, has a few different "preference" files (the extension is .plist), which store all your user settings. Each time you resize a window, change a setting, anything, this file is re-written. Kinda easy to see how they would become corrupt every now and then.
-Close FCP
-Navigate to User>Library>Preferences and delete com.apple.FinalCutPro.plist
-Navigate to User>Library>Preferences>Final Cut Pro User Data and delete Final Cut Pro 5.0 Prefs
-Empty your trash
Relaunch FCP and see if that worked.
Download FCP Rescue to make this process easier in the future. When you have FCP running really smooth, open FCP Rescue and create a backup of your preference files. If it starts acting wanky, just run FCP Rescue and Restore your backup preferences. Works really slick, and it's free.
EDIT: Or use the really simple explaination that X posted as I was typing.

Losing network connection and NIC acts weird from warm/hot weather/temperatures?

Hello.
Is there a known issue on MSI P43 NEO3-F (MSI-7514) motherboards' onboard RealTek RTL8168C (P)/8111C(P) PCI-E Gigabit Ethernet NIC network disconnecting and acting weird during warm/hot weather?
I noticed lately and back on 1/11/2009 night when weather got warm/hot (e.g., my room can get over 85F degrees, but lately it has been 80F degrees), my network would lose its connection. See http://img9.imageshack.us/img9/5580/screenshots.gif for a few SpeedFan's sensor readings when the incidents occurred. I have never seen this happen when the weather is cooler (60-70F degrees in my room).
I also think this only happens if I am using the PC lightly (nothing intensive) like watching fullscreen videos (video overlay), surfing the Web, etc. I don't see any errors or evidences that it happens when idled (e.g., asleep or out). Uptime doesn't seem to matter since I have seen days to 3.5 hours.
I tried upgrading network driver twice (e.g., Realtek_XP_5714_0219 from
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false ...), disabling Kerio Personal Firewall v2.1.5 (XP's disabled already), releasing and renewing IP address (works, but still no network -- can't even ping my router!), unplugging and replugging the cat5 cable (do see the network port lights on), touching the network jack and hardware inside and outside of the case (not hot), trying another cat5 cable and a network port on a switch instead router's), changing from "Minimal Power Management" to full power (no underclocking/slowing down when idled), etc.
During the disconnections, I tried:
C:\>tracert 192.168.0.1
Tracing route to 192.168.0.1 over a maximum of 30 hops
1 * * * Request timed out.
2 * * * Request timed out.
3 * * ^C
IPCONFIG.EXE /ALL when having network problems:
Windows IP Configuration
Host Name . . . . . . . . . . . . : FOOBAR
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter VMware Network Adapter VMnet8:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8
Physical Address. . . . . . . . . : 00-50-56-C0-00-08
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.134.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Ethernet adapter VMware Network Adapter VMnet1:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1
Physical Address. . . . . . . . . : 00-50-56-C0-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.80.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Ethernet adapter HDTV Tuner 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : TechniSat DVB-PC TV Star PCI #3
Physical Address. . . . . . . . . : 00-D0-D7-30-19-C1
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 169.254.178.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 169.254.178.1
Lease Obtained. . . . . . . . . . : Saturday, February 28, 2009 6:55:04 PM
Lease Expires . . . . . . . . . . : Monday, July 13, 2009 11:28:08 PM
Ethernet adapter HDTV Tuner 1:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : TechniSat DVB-PC TV Star PCI
Physical Address. . . . . . . . . : 00-D0-D7-30-1A-1D
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 169.254.178.4
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 169.254.178.1
Lease Obtained. . . . . . . . . . : Saturday, February 28, 2009 6:55:21 PM
Lease Expires . . . . . . . . . . : Monday, July 13, 2009 11:28:25 PM
Ethernet adapter Local Area Connection 15:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
Physical Address. . . . . . . . . : 00-21-85-1A-C6-72
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.82
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 192.168.0.1
4.2.2.1
I checked Windows XP Pro. SP3's event logs and noticed these during the disconnections:
Event logs showed:
Event Type: Information
Event Source: Tcpip
Event Category: None
Event ID: 4201
Date: 2/28/2009
Time: 6:42:23 PM
User: N/A
Computer: FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
Event Type: Information
Event Source: BROWSER
Event Category: None
Event ID: 8033
Date: 2/28/2009
Time: 6:47:22 PM
User: N/A
Computer: FOOBAR
Description:
The browser has forced an election on network \Device\NetBT_Tcpip_{89F40100-0D8D-4C33-A32D-3D91CAEB3FBD} because a master browser was stopped.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Event Type:   Information
Event Source:   Tcpip
Event Category:   None
Event ID:   4201
Date:      3/1/2009
Time:      6:19:08 AM
User:      N/A
Computer:   FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
Event Type:   Information
Event Source:   Tcpip
Event Category:   None
Event ID:   4201
Date:      3/1/2009
Time:      6:19:20 AM
User:      N/A
Computer:   FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
I also noticed the disconnections usually start with red X icon in my taskbar with its bubble and then later the long disconnection even though no red X (1 GB and connected). If I were to disconnect the cat5 cable from NIC, then it wouldn't even detect it is missing the cable!
The only way to fix this was to reboot (best way and last longer) OR disable network connection and re-enable it (Windows XP's Network Connections) or the NIC itself (Device Manager), but that doesn't always last long (maybe a minute). Example of my pings right after disabling and re-enabling NIC:
C:\>ping 192.168.0.1 -t
Pinging 192.168.0.1 with 32 bytes of data:
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Request timed out.
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
MSINFO32 in case it helps (seems OK to me, but I am not a hardware expert):
[Conflicts/Sharing]
Resource   Device
I/O Port 0x00000000-0x00000CF7   PCI bus
I/O Port 0x00000000-0x00000CF7   Direct memory access controller
I/O Port 0x000003C0-0x000003DF   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x000003C0-0x000003DF   ATI Radeon HD 4800 Series
IRQ 21   Intel(R) ICH10 Family USB Universal Host Controller - 3A38
IRQ 21   OHCI Compliant IEEE 1394 Host Controller
IRQ 21   TechniSat DVB-PC TV Star PCI
IRQ 23   Intel(R) ICH10 Family USB Universal Host Controller - 3A34
IRQ 23   Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3A
I/O Port 0x0000B000-0x0000BFFF   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x0000B000-0x0000BFFF   ATI Radeon HD 4800 Series
IRQ 16   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
IRQ 16   ATI Radeon HD 4800 Series
IRQ 16   Intel(R) ICH10 Family USB Universal Host Controller - 3A37
IRQ 16   Standard Dual Channel PCI IDE Controller
IRQ 16   Intel(R) ICH10 Family PCI Express Root Port 2 - 3A42
IRQ 16   Intel(R) ICH10 Family PCI Express Root Port 6 - 3A4A
IRQ 16   ASUS TV880 Video Capture (NTSC)
IRQ 17   Microsoft UAA Bus Driver for High Definition Audio
IRQ 17   Intel(R) ICH10 Family PCI Express Root Port 1 - 3A40
IRQ 17   Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
Memory Address 0xD0000000-0xDFFFFFFF   Intel(R) 4 Series Chipset PCI Express Root Port -
2E21
Memory Address 0xD0000000-0xDFFFFFFF   ATI Radeon HD 4800 Series
IRQ 18   Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3C
IRQ 18   Intel(R) ICH10 Family USB Universal Host Controller - 3A36
IRQ 19   Intel(R) ICH10 Family USB Universal Host Controller - 3A39
IRQ 19   Intel(R) ICH10 Family USB Universal Host Controller - 3A35
IRQ 19   Intel(R) ICH10 Family 4 port Serial ATA Storage Controller 1 - 3A20
IRQ 19   Intel(R) ICH10 Family 2 port Serial ATA Storage Controller 2 - 3A26
Memory Address 0xA0000-0xBFFFF   PCI bus
Memory Address 0xA0000-0xBFFFF   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
Memory Address 0xA0000-0xBFFFF   ATI Radeon HD 4800 Series
Memory Address 0xFED90000-0xFED93FFF   System board
Memory Address 0xFED90000-0xFED93FFF   System board
I/O Port 0x000003B0-0x000003BB   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x000003B0-0x000003BB   ATI Radeon HD 4800 Series
[IRQs]
Resource   Device   Status
IRQ 9   Microsoft ACPI-Compliant System   OK
IRQ 16   Intel(R) 4 Series Chipset PCI Express Root Port - 2E21   OK
IRQ 16   ATI Radeon HD 4800 Series   OK
IRQ 16   Intel(R) ICH10 Family USB Universal Host Controller - 3A37   OK
IRQ 16   Standard Dual Channel PCI IDE Controller   OK
IRQ 16   Intel(R) ICH10 Family PCI Express Root Port 2 - 3A42   OK
IRQ 16   Intel(R) ICH10 Family PCI Express Root Port 6 - 3A4A   OK
IRQ 16   ASUS TV880 Video Capture (NTSC)   OK
IRQ 17   Microsoft UAA Bus Driver for High Definition Audio   OK
IRQ 17   Intel(R) ICH10 Family PCI Express Root Port 1 - 3A40   OK
IRQ 17   Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC   OK
IRQ 21   Intel(R) ICH10 Family USB Universal Host Controller - 3A38   OK
IRQ 21   OHCI Compliant IEEE 1394 Host Controller   OK
IRQ 21   TechniSat DVB-PC TV Star PCI   OK
IRQ 19   Intel(R) ICH10 Family USB Universal Host Controller - 3A39   OK
IRQ 19   Intel(R) ICH10 Family USB Universal Host Controller - 3A35   OK
IRQ 19   Intel(R) ICH10 Family 4 port Serial ATA Storage Controller 1 - 3A20   OK
IRQ 19   Intel(R) ICH10 Family 2 port Serial ATA Storage Controller 2 - 3A26   OK
IRQ 18   Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3C   OK
IRQ 18   Intel(R) ICH10 Family USB Universal Host Controller - 3A36   OK
IRQ 23   Intel(R) ICH10 Family USB Universal Host Controller - 3A34   OK
IRQ 23   Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3A   OK
IRQ 20   Creative SB Audigy 2 ZS (WDM)   OK
IRQ 22   TechniSat DVB-PC TV Star PCI #3   OK
IRQ 0   System timer   OK
IRQ 8   System CMOS/real time clock   OK
IRQ 13   Numeric data processor   OK
IRQ 4   Communications Port (COM1)   OK
IRQ 6   Standard floppy disk controller   OK
IRQ 1   Standard 101/102-Key or Microsoft Natural PS/2 Keyboard   OK
IRQ 12   Microsoft PS/2 Mouse   OK
IRQ 14   Intel(R) ICH10 Family SMBus Controller - 3A30   OK
My detailed computer configurations can be found here: http://alpha.zimage.com/~ant/antfarm/about/computers.txt (primary computer).
Thank you in advance.

Quote from: NovJoe on 02-March-09, 23:10:05
Force your NIC to run at 100Mbps full duplex and see how it goes.
Check your router / switch ports as well as cables.
I will try 100 Mbps if it happens again. So far, it hasn't occurred after installing the driver supplied by MSI's Web site and not RealTek's Web site. The room temperatures even got warmer like 83F degrees.
As for router and switch, what am I checking for? Other computers didn't have any problems. As for cat5 cables, I already tried another one like I said in my original post.

Intermittently losing pop smtp and isp connection

Intel Mac Mini, Mountain Lion, 8 GB RAM
Intermittently losing pop, smtp and sometimes isp connectivity.
Can ping to IP address, not to isp name
Same for wired and wireless connection
Other Macs on network do not have the same problem
ISP says no POP or nameserver issues
Have:
run hardware diagnostics - all OK
disk utility -> repair disk - no issues
memtest - no issues
Onyx full maintenance and cleaning - no issues
Erase HD, fresh media re-install, time machine restore
started to lose sanity

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the request of a stranger on a public message board. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed: Copy a line of text from this web page into the window of another application. Wait for the script to run. It usually takes a few minutes. Then paste the results, which will have been copied automatically, back into a reply on this page. The sequence is: copy, paste, wait, paste again. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin; clear; Fb='%s\n\t(%s)\n'; Fm='\n%s\n\n%s\n'; Fr='\nRAM details\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; M () { find -L "$d" -type f | while read f; do file -b "$f" | egrep -lq XML\|exec && echo $f; done; }; Pc () { o=`grep -v '^ *#' "$2"`; l=`wc -l <<< "$o"`; [[ l -gt 25 ]] && o=`head -n25 <<< "$o"`$'\n'"[$((l-25)) more line(s)]"; Pm "$1"; }; Pm () { [[ "$o" ]] && o=`sed -E '/^ *$/d; s/^ */ /; s/[-0-9A-Fa-f]{22,}/UUID/g' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o=`echo $o`; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; R () { o=; [[ r -eq 0 ]]; }; SP () { system_profiler SP${1}DataType; }; id -G | grep -qw 80; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; SP Software | sed '8!d;s/^ *//'; h=(`SP Hardware | awk '/ Id/{print $3}; /Mem/{print $2}'`); o=$h; Ps "Model"; o=$((h[1]<4?h[1]:0)); Ps "Total RAM (GB)"; o=`SP Memory | sed '1,5d;/[my].*:/d'`; [[ "$o" =~ s:\ [^O]|x([^08]||0[^2]8[^0]) ]] && printf "$Fr" "$o"; o=`SP Diagnostics | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; p=`SP Power`; o=`awk '/Cy/{print $NF}' <<< "$p"`; o=$((o>=300?o:0)); Ps "Battery cycles"; o=`sed -n '/Cond.*: [^N]/{s/^.*://p;}' <<< "$p"`; Ps "Battery condition"; for b in Thunderbolt USB; do o=`SP $b | sed -En '1d;/:$/{s/ *:$//;x;s/\n//p;};/^ *V.* [0N].* /{s/ 0x.... //;s/[()]//g;s/(.*: )(.*)/ $\2$/;H;};/Apple|Genesy|Intel|SMSC/{s/.//g;h;}'`; Pm $b; done; o=`pmset -g therm | sed 's/^.*C/C/'`; [[ "$o" =~ No\ th|pms ]] && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; [[ "$o" =~ =\ [^GO] ]] || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; a=(/ ""); A=(System User); for i in 0 1; do o=`cd ${a[$i]}L*/Lo*/Diag* || continue; for f in *.{cr,h,pa,s}*; do [[ -f "$f" ]] || continue; d=$(stat -f%Sc -t%F "$f"); [[ "$f" =~ h$ ]] && grep -lq "^Thread c" "$f" && e=\* || e=; echo $d ${f%%_2*} ${f##*.} "$e"; done | sort | tail`; Pm "${A[$i]} diagnostics"; done; [[ "$o" =~ \*$ ]] && printf $'\n* Code injection\n'; o=`syslog -F bsd -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|SATA W|ssert|Thrott|timed? ?o' | tail -n25 | awk '/:/{$4=""; $5=""};1'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); n=$((${#s[*]}-1)); c="${s[*]}"; o=${s[$n]}%; Ps "CPU usage by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); n=$((${#s[*]}-1)); s[$n]=${s[$n]%[+-]}; c="${s[*]}"; o=$((s[$n]>=25000?s[$n]:0)); Ps "Mach ports used by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | awk 'NR>1 && !/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|post[fg]|x)/{print $3}'`; Pm "Extrinsic daemons"; o=`launchctl list | awk 'NR>1 && !/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`for d in {/,}L*/Lau*; do M; done | grep -v com\.apple\.CSConfig | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`for d in /{S*/,}L*/Star*; do M; done`; Pm "Startup items"; o=`find -L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo}* -type d -name Contents -prune | while read d; do ID=$($PB\ :CFBundleIdentifier "$d/Info.plist") || ID="No bundle ID"; [[ "$ID" =~ ^com\.apple\.[^x]|Accusys|ArcMSR|ATTO|HDPro|HighPoint|driver\.stex|hp-fax|\.hpio|JMicron|microsoft\.MDI|print|SoftRAID ]] || printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find -L /u*/{,*/}lib -type f | while read f; do file -b "$f" | grep -qw shared && ! codesign -v "$f" && echo $f; done`; Pm "Unsigned shared libraries"; o=`for e in INSERT_LIBRARIES LIBRARY_PATH; do launchctl getenv DYLD_$e; done`; Pm "Environment"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; Ps "DNS"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; f=auto_master; [[ `md5 -q /etc/$f` =~ ^b166 ]] || Pc $f /etc/$f; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; Pc "hosts" <(grep -v 'host *$' /etc/hosts); Pc "User launchd" ~/.launchd*; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l | sed -E 's:/Users/[^/]+/:/Users/USER/:g'); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed -E 's/(\..*$|-[1-9])//g'; o=`find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ | wc -l`; Ps "Restricted user files"; cd; o=`SP Fonts | egrep "Valid: N|Duplicate: Y" | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist | while read f; do plutil -s "$f" >&- || echo $f; done`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} file count"; done; o=; [[ UID -eq 0 ]] && o=root; Ps "UID"; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test will take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line "[Process completed]" to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of Apple Support Communities ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

I have just connected my new apple tv, in the main menu I see only two icons; "computers" and "settings". Where do I find the icons for internet, movies etc. We do not live in the US..

I have just connected my new apple TV and in the main menu see only two icons: computers and settings. How do I access the rest of the icons (internet, movies etc...) We do not live in the US. The unit has full WiFi access with no problems, I can access ITunes on my laptop via home sharing no problem.

Glad that this solved your problem but if you searh past threads there are a LOT of people with identical problems.
Reading through the threads my take is
There seems to be something awry with wifi chipset. Typical symptoms are initially being able to connect to connect to a Wifi network then the connection is dropped. Then you see just the 'computers' and 'settings' icons on screen
Power off, reset and factory restore doesnt seem to solve it
Occasionally its nearby antenna cables etc causing interference
One report with convincing evidence it was the HDMI cable, swapping to anotehr cable fixed the problem
Plugging in ethernet works, this is purely a wifi issue
Sometimes plugging in ethernet temporararily wakes up the wifi
Many people seem to have exchanged their units only for the same thing to happen to the new unit a few weeks later. Just wondering if its a fomponent fail or heat issue.

Two ISP connection and 4 NIC

Similar Messages

Maybe you are looking for