Ubuntu running under Hyper-V with high load
I'm running a VM for Ubuntu Server 12.04 LTS under Hyper-V and with no web server or any other public server installed, the system load is 1.0
The VM is using a 75GB fixed VHD on its own partition (the hard drive is using raid 0).
Is this normal for running a linux OS under Hyper-V?
Here's what top shows (i restarted the vm for fresh numbers, but it still shows a load of 1.00 even after its been running for a day):
top - 16:58:17 up 23 min, 1 user, load average: 1.00, 0.58, 0.24
Tasks: 235 total, 1 running, 234 sleeping, 0 stopped, 0 zombie
Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 98.8%id, 1.0%wa, 0.0%hi, 0.2%si, 0.0%st
Mem: 4040336k total, 870384k used, 3169952k free, 13232k buffers
Swap: 7812092k total, 0k used, 7812092k free, 225396k cached
The host OS is running Windows 2012 R2 and it too isint running anything else that would put a lot of load on the server.
Hi Sir,
The following daemons must be installed manually for Ubuntu distributions:
VSS Snapshot daemon – This daemon is required to create live Linux virtual machine backups.
KVP daemon – This daemon allows setting and querying intrinsic and extrinsic key value pairs.
To install both daemons, please use the following command:
Copy
# sudo apt-get update
# sudo apt-get install hv-kvp-daemon-init
# uname –r
<kernel release>
# sudo apt-get install linux-tool-<kernel release>
# sudo apt-get install linux-cloud-tools-<kernel release>
Please refer to note 5 , 9 within following article :
https://technet.microsoft.com/en-us/library/dn531029.aspx
As for linux VM running on hyper- v, I would suggest you to try to get further assistance from this forum:
https://social.technet.microsoft.com/Forums/en-US/home?forum=linuxintegrationservices&filter=alltypes&sort=lastpostdesc
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .
Similar Messages
-
How to verify if backups are set up and running on Hyper-V with Ubuntu 12.04 on vm ?
I have Windows Server 2008 R2 with Hyper-V installed and Ubuntu 12.04 running on a VM.
I would like to be able to verify if Windows Server Backups are in fact backing up the Ubuntu VM.
From within Hyper-V Manager no snapshots appear for the VM.
I have done a lsmod on Ubuntu to verify if LIS is installed , this is the output:
Module Size Used by
vesafb 13844 1
joydev 17693 0
hid_hyperv 13164 0
hid 99559 1 hid_hyperv
mac_hid 13253 0
psmouse 87603 0
serio_raw 13211 0
i2c_piix4 13301 0
lp 17799 0
parport 46562 1 lp
hv_netvsc 22939 0
hv_utils 13540 0
hv_storvsc 17896 2
hv_vmbus 34543 4 hid_hyperv,hv_netvsc,hv_utils,hv_storvsc
floppy 70365 0
A ps -ef outputs this:
root 217 2 0 2013 ? 00:00:00 [hv_vmbus_con]
root 218 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 219 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 220 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 221 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 222 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 223 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 224 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 225 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 226 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
root 227 2 0 2013 ? 00:00:00 [hv_vmbus_ctl]
(not the entire output, just what I think is relevant)
When checking the registry on Server 2008 I cannot find the key
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\WindowsServerBackup\Application Support\{66841CD4-6DED-4F4B-8F17-FD23F8DDC3DE}
as described how to setup in this link: http://support.microsoft.com/kb/958662
From what I can gather VSS will be able to run without the need to shutdown the Ubuntu VM but the backups are not running when Windows Server Backups run?
How can I verify IF any backups of the VM have run successfully at all?
I am new to Hyper-V - but from what I can see , it seems that no VM backups are running . The normal Windows Server backups are running nightly. I would like them to run together without having to restart/ take offline/reboot the VM.
This is a production server and I need to avoid rebooting as much as possible-Hi Sir,
The following daemons must be installed manually for Ubuntu distributions:
VSS Snapshot daemon – This daemon is required to create live Linux virtual machine backups.
KVP daemon – This daemon allows setting and querying intrinsic and extrinsic key value pairs.
To install both daemons, please use the following command:
Copy
# sudo apt-get update
# sudo apt-get install hv-kvp-daemon-init
# uname –r
<kernel release>
# sudo apt-get install linux-tool-<kernel release>
# sudo apt-get install linux-cloud-tools-<kernel release>
Please refer to note 5 , 9 within following article :
https://technet.microsoft.com/en-us/library/dn531029.aspx
As for linux VM running on hyper- v, I would suggest you to try to get further assistance from this forum:
https://social.technet.microsoft.com/Forums/en-US/home?forum=linuxintegrationservices&filter=alltypes&sort=lastpostdesc
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] . -
Delay, reason due with high load
On MAC OS X 10.9.x when i compiled something(high load ~100%) music was not interrupting (stammer). Now it's will be always? (YOSEMITE)
On MAC OS X 10.9.x when i compiled something(high load ~100%) music was not interrupting (stammer). Now it's will be always? (YOSEMITE)
-
App running under lock screen with StreamSocket and SpeechSynthesizer
On wp8 silverlight this was easy. PhoneApplicationService.Current.ApplicationIdleDetectionMode = IdleDetectionMode.Disabled;
In 8.1 xaml how would I go about this? I have found an ugly hack online that keeps the screen alive, this is not a solution that I can use. My users need to start my app, select a car transponder that they want to hear lap times from, connect to my server
(over wifi to a local computer running my server code, no internet) hit the lock button, then put their phones in their pockets while they drive and get the lap times on their earpiece.
I have the new and more cumbersome text-to-speech working (how you have to have an invisible media element on a the active page for mediaended to fire was especially annoying!). I have the streamsocket stuff working, just not under the lock screen. I don't
really need it to be a "background task". It is understood and preferable that it disconnects the moment you leave the page where get your live lap times.
controlchanneltrigger seemed promising, you can use it for store apps... but not phone.
To summarize.
1. connect to server with streamsocket api
2. lock screen and put phone in pocket
3. app should stay alive and as packets arrive from the server (one packet every 10 seconds on average), store lap time results and say them out loud using text to speech.
https://youtu.be/0VnOh6s3hww
At this point I'm pretty fed up and I'm about to pull the plug on the WP8.1 version, my first experience with xaml was... unpleasant... So if you have some good keywords I can search for that would be appreciated.Hi torg,
The most similar API on Windows Phone 8.1 is
RequestActive | requestActive method, see this for more information: How to keep the display on during audio/video playback (XAML)
--James
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Hey there,
somehow I cant get my Zalman Trimon Monitor to run on my new Mac book pro (2012, Retina). I tried hooking it up with the Dr. Bott Mini Display port Adapter see here ( http://www.google.de/products/catalog?client=safari&rls=en&oe=UTF-8&redir_esc=&q =dr.+bott+mini+displayport&um=1&ie=UTF-8&tbm=shop&cid=9085840057573220630&sa=X&e i=rHMeULWUNo7ysgaZvYGYAg&ved=0CHIQ8gIwBg#ps-sellers )
Neither on my new mac book (with thunderbold) nore with the 2010 Mac book pro 13 inch from my girlfriend both running Mountain Lion, would it work. Does anyone has the same troubles or knows a reason or fix? The monitor definitly works (tried with my old mac book) and this is already the second adapter I use, since I thought maybe the adapter doesnt work!
Help appreciated!Hm, i cannot reproduce the kernel_task thing right now, but this is my temp after working with 2 screens for 10 minutes. is this normal?
100° cpu, 96° on the diode, and 78 on GPU chip? it even was 82 once.
when do i reach critical limits?
apple? -
How to run jar file created with higher version on lower version ?
Hi,
I downloaded a jar file and trying to run it on Linux machine with Java version 1.4...
I got error that jar file complied with 1.5 version.
Is there any way to run it on 1.4 version. I don't want to upgrade Java version of my linux :)
Regards,
AjayEJP wrote:
On the contrary, the 'reality' is that it is better, and probably easier, once you analyse and present the comparative costs and risks correctly, to get the mandate lifted than to back-port code to platform levels for which it was not designed.The main blockade (judging by my observations) for actually doing it is that this is not a simple code change, which is what programmers really, really, really want to keep it within their comfort zone. All of a sudden you're tasked with software upgrades and the demands that it brings, such as testing to make sure everything still works properly and getting grumpy system's administrators to actually go do it.
I wouldn't be surprised that there are people out there that would rather back port a library than to take the initiative to get Java upgraded :/ -
Mac Pro fans run at max speed with no load
I recently picked up a Mac Pro 12core and it's been working amazingly well for the past few months... in the past day or two though the fan has been ramping up to maximum and staying there. When this happens there are no processes taking more than 4% CPU and the system is never less than 99% idle. Resetting the SMC controller solved the issue for about 8 hours overnight, but when I started using the computer this morning the fan ramped up about 15mins into using it.
The temps (in degrees C) around the mac pro: (collected with iStat Server):
CPUs: 23,22
Ambient: 23
HD Bays: 23,25,24
Mem Banks: 22,21,25,25,25,27,27,22
Northbridge: 27
Power supplies: 33,36
As you can see, nothing is hot... I'm not exactly sure how to calm it down. Nothing is working any differently than it was, it's just VERY LOUD now where it was whisper quiet, hahaI did order it from the Apple Refurb shop and I think it'd fall into that timeframe (got it early November), but I was kinda hoping for some things I could try on my own before shipping it out?
-
FX8320 with MSI 760GA-P43 (FX) MS-7699 drop speed on high load
I had an FX8320 with watercooling on this MS-7699 motherboard, when with high load the CPU (all 8 cores) drop to 1.4Ghz then come back to the normal frequency within a few seconds, is there anyway to maintain the cpu speed at all time with high load?
No there isn't. The board is not able to cope with the power draw of an FX83xx cpu. Sadly MSI for some time listed FX 8-core cpus supported on all 760G product sites despite these are only able to run 95W TDP cpus at the very maximum. The behavior you are experiencing is a cheap trick to make the cpu seem supported while the only way to keep the board from burning up is to throttle the cpu under load. To run the cpu at full performance you need a new board meant for supporting 125w+ cpus.
-
I´ve tested 3 different linux versions ( Red Hat 5.6, 6.0 and 6.2 ) running under Hyper-V 3 (Win2012R2) and the behaviour is always the same, the network service starts up, the IP address is binded to the NIC, the NIC responds to PING requestes
coming from localhost, but...
There´s no communication with any other host n the network. I have several windows machines working well, same vSwitch for all VMs, Generation1 machine, tested with Legacy adaptaer and "standard" net adapter as well.
I have to install ICs even using the Legacy NIC?
RH7.0 works better?There´s no communication with any other host n the network. I have several windows machines working well, same vSwitch for all VMs, Generation1 machine, tested with Legacy adaptaer and "standard" net adapter as well.
I have to install ICs even using the Legacy NIC?
RH7.0 works better?
For RHEL 6.3 and below, you need to install IC for network to work with "standard" NIC.
Can you use a newer version of RHEL 6? The IC are integrated in them.
RHEL 7 comes with IC integrated. -
Running under fedora 2 kernel 2.6
labview crashes when run under fedora 2 with the new kernel 2.6. error message is LabVIEW caught fatal signal
7.0 - Received SIGSEGV
Reason: address not mapped to object
Attempt to reference address: 0x27e1bf7c
Will kernel 2.6 be supported soon?I'm able to run LV 7.0 on kernel 2.6.3 without problems. However, I've
read that it could have trouble with the new threading system in 2.6.x.
LV 7.1 supposedly resolves potential threading issues. Still, you should
be able to at least open LV without any problems - from what I've seen so
far.
I bet the problem you're seeing is more links to the Fedora 2 distibution.
Be careful with Fedora, they tend to use the most recent release of
everything. I had a similar discussion with someone less than a month
ago. Looked like there was a problem with the version of glibc libraries
in Fedora 2. I'm not sure what he did next, he never replied to the
group. I bet he went back to Fedora 1.
Good luck! -
RAC Issue with high Transaction OLTP + GC's
In the Lab i am testing in-house application with Oracle 10g.
Setup
- 2 Database servers (RHEL OS 3, IBM H/W, 4GB RAM)
- 2 in house Application servers (RHEL OS 3, IBM H/W, 4GB RAM)
- IBM Disk Array with 2Gbps fiber Cable Speed
- Cisco LAN Switch with 100mbps/sec Port
Application Detail-
-- Its a OLTP application.
-- Doing lots of insertion,update,delete,commit for each transaction.
-- With high application load,its doing 5000 DB tranactions/sec with database.
The following test scenario need to test
1. Start one application server and conenct with DB instance1 and push high load..
2. Start both application server and connect with DB Instance1b and push high load from both applications.
3. Start Both application server and connect with both DB servers ( For Ex.
(A1-DB1 & A2-DB2) and check the application compatibility with RAC environment ( Note- Here need to push very less db transaction data to DB servers).
4. Similar like 3 but with very high db transaction rate
Now these are the results
1. Full Success
2. Full Success
3. Full Success
4. Fail
Detail description of Case4 Failure.
When ever i am starting applications with high load, within few minutes application quesues are getting full and db instances are not able to handle load.
When i checked the Oracle ASH Report and then found following major events
1. gc buffer busy
2. gc current block busy
3. gc current multi block request
4. gc cr block 2-way
i checked the oracle documents and found three are major root cause for this issue.
-- Interconnect
-- Load issues
-- SQL Execution against a Large shared working set
But i am not sure, how i can come out from this issue.
If any one faced this issue with Oracle RAC. Please share your experience or give some suggestion to come out from this issue.
Rgds
Sumit
Bangalore,IndiaHi,
you can use fiber for interconnect, Once i have looked for this option but haven't implemented.......
in this case your global cache requests are too much. one thing more if is it possible then divide the load according to domains. like same queries on on node and other domain queries on second nodes...... e.g. reporting on node2 and oltp transations on node1.
and kindly look into it...
http://www.ardentperf.com/2007/09/12/gc-buffer-busy-waits-in-rac-finding-hot-blocks/ -
Facing problems with URLConnection under high load
Hi,
I have a piece of code that acts as a load balancer. Under high load scenario - 200+ different simulataneous users, it throws some errors.
Following is a snippet from that code -
URL url = new URL(site);
URLConnection urlconnection = url.openConnection();
urlconnection.setDoInput(true);
urlconnection.setDoOutput(true);
urlconnection.setUseCaches(false);
DataOutputStream dataoutputstream =
new DataOutputStream(urlconnection.getOutputStream());
dataoutputstream.writeBytes(posServiceRequest);
dataoutputstream.flush();
dataoutputstream.close();
InputStream inputstream = urlconnection.getInputStream();
httpservletresponse.setContentType(urlconnection.getContentType());
rewriteStreams(inputstream, httpservletresponse.getOutputStream());
inputstream.close();
Somewhere after around 200 odd users, this piece of code throws an error - "Error writing to server", a stacktrace print shows that the error occurs at the following line -
InputStream inputstream = urlconnection.getInputStream();
Any pointers would be appreciated.
Thanks,
-rahulMore information please. What is the exception class, what is its entire text, and what is the stack trace.
-
WRT1900AC running at high loads
I had too many issues with the EA6900, and connection dropping, so i decided to try the WRT1900AC, and OMG I LOVE IT!!! on 5 GHz network i get full signal 40 ft away from the router in another room with the door shut.
One question though..... I noticed the load on my EA6900 was around .050 on average but on my WRT1900AC its always around 1.30 CPU load...
Is this normal, and or just because its a faster CPU that it is able to do more so it runs a bigger load??? I'm a linux geek, and owned a web hosting business so i'm familiary with average loads etc..
THANKS!Thanks for your posts
Keep in mind that the WRT1900AC is a dual core system. So a load of 2.00 is 100% capacity.
For one minute you had 4.06 which high but still fine as long as it's not sustained.
For five minutes you had 2.08 with is fine but the WRT1900AC was running at capacity
For 15 minutes you had 1.77 which is good but doesn't leave a lot of head room
Keep monitoring and see if the 15 minute load is always below 2.00. That would mean that for the most part the WRT1900AC is running under capacity.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support -
Thunderbird on Win 8.1 with Windows Defender is not downloading attachments from my roadrunner email account. It does so when running under Ubuntu 12.04 though. On Windows no attachments are shown. Also on Windows there is content that is not shown, I know so as there is an empty box. Then there is no option to download offline content. How may I use Thunderbird to read my email if it won't display properly? I trust the source of these emails as they are from the legal department of my former employer. I asking for the content to be resent does not work either. Please help me.
Thank you;
Below is information on my Win 8.1 configuration.
Application Basics
Name: Thunderbird
Version: 31.6.0
User Agent: Mozilla/5.0 (Windows NT 6.3; WOW64; rv:31.0) Gecko/20100101 Thunderbird/31.6.0
Profile Folder: Show Folder
(Local drive)
Application Build ID: 20150330093429
Enabled Plugins: about:plugins
Build Configuration: about:buildconfig
Memory Use: about:memory
Mail and News Accounts
account1:
INCOMING: account1, , (imap) mail.twc.com:143, plain, passwordCleartext
OUTGOING: mail.twc.com:587, alwaysSTARTTLS, passwordCleartext, true
account2:
INCOMING: account2, , (none) Local Folders, plain, passwordCleartext
Crash Reports
Extensions
Show All Body Parts, 1.2, true, [email protected]
Important Modified Preferences
Name: Value
browser.cache.disk.capacity: 358400
browser.cache.disk.smart_size_cached_value: 358400
browser.cache.disk.smart_size.first_run: false
browser.cache.disk.smart_size.use_old_max: false
extensions.lastAppVersion: 31.6.0
font.internaluseonly.changed: true
font.name.monospace.el: Consolas
font.name.monospace.tr: Consolas
font.name.monospace.x-baltic: Consolas
font.name.monospace.x-central-euro: Consolas
font.name.monospace.x-cyrillic: Consolas
font.name.monospace.x-unicode: Consolas
font.name.monospace.x-western: Consolas
font.name.sans-serif.el: Calibri
font.name.sans-serif.tr: Calibri
font.name.sans-serif.x-baltic: Calibri
font.name.sans-serif.x-central-euro: Calibri
font.name.sans-serif.x-cyrillic: Calibri
font.name.sans-serif.x-unicode: Calibri
font.name.sans-serif.x-western: Calibri
font.name.serif.el: Cambria
font.name.serif.tr: Cambria
font.name.serif.x-baltic: Cambria
font.name.serif.x-central-euro: Cambria
font.name.serif.x-cyrillic: Cambria
font.name.serif.x-unicode: Cambria
font.name.serif.x-western: Cambria
font.size.fixed.el: 14
font.size.fixed.tr: 14
font.size.fixed.x-baltic: 14
font.size.fixed.x-central-euro: 14
font.size.fixed.x-cyrillic: 14
font.size.fixed.x-unicode: 14
font.size.fixed.x-western: 14
font.size.variable.el: 17
font.size.variable.tr: 17
font.size.variable.x-baltic: 17
font.size.variable.x-central-euro: 17
font.size.variable.x-cyrillic: 17
font.size.variable.x-unicode: 17
font.size.variable.x-western: 17
gfx.direct3d.last_used_feature_level_idx: 0
mail.openMessageBehavior.version: 1
mail.winsearch.firstRunDone: true
mailnews.database.global.datastore.id: 6859eb31-fcde-4f29-ae94-8ac4ec7602a
network.cookie.prefsMigrated: true
places.database.lastMaintenance: 1428360994
places.history.expiration.transient_current_max_pages: 104858
plugin.importedState: true
Graphics
Adapter Description: Intel(R) HD Graphics 5500
Vendor ID: 0x8086
Device ID: 0x1616
Adapter RAM: Unknown
Adapter Drivers: igdumdim64 igd10iumd64 igd10iumd64 igdumdim32 igd10iumd32 igd10iumd32
Driver Version: 10.18.14.4029
Driver Date: 11-18-2014
Adapter Description (GPU #2): AMD Radeon R7 M270
Vendor ID (GPU #2): 0x1002
Device ID (GPU #2): 0x6604
Adapter RAM (GPU #2): 4095
Adapter Drivers (GPU #2): aticfx64 aticfx64 aticfx64 aticfx32 aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64
Driver Version (GPU #2): 14.301.1002.1001
Driver Date (GPU #2): 10-1-2014
Direct2D Enabled: true
DirectWrite Enabled: true (6.3.9600.17415)
ClearType Parameters: ClearType parameters not found
WebGL Renderer: false
GPU Accelerated Windows: 2/2 Direct3D 10
AzureCanvasBackend: direct2d
AzureSkiaAccelerated: 0
AzureFallbackCanvasBackend: cairo
AzureContentBackend: direct2d
JavaScript
Incremental GC: 1
Accessibility
Activated: 1
Prevent Accessibility: 0
Library Versions
Expected minimum version
Version in use
NSPR
4.10.6
4.10.6
NSS
3.16.2.3 Basic ECC
3.16.2.3 Basic ECC
NSS Util
3.16.2.3
3.16.2.3
NSS SSL
3.16.2.3 Basic ECC
3.16.2.3 Basic ECC
NSS S/MIME
3.16.2.3 Basic ECC
3.16.2.3 Basic ECCDoes this occur with defender turned off?
-
My mac book pro on start up shows a white screen with a folder with a question mark in it then switches to the apple symbol with the loading bar under it but it freezes about half way. Only started to have problems since upgrading to yosemite any ideas.
I do hope you have recent backup, because it look like your hard disk is failing. You can start up in Recovery Mode, and run Disk Utility to see if the disk can be fixed: OS X: About OS X Recovery - Apple Support
Maybe you are looking for
-
How much will I need to pay for a complete CC?
I don't wish to pay a monthly fee.
-
Help
-
Oracle Lite DB 연결 성공하신분 없나요?
개발환경 : Win7 x86, Visual Studio 2008, Oracle lite 10g 플랫폼 : Pocket PC 2003 SE .... 아는 개발자중에서도 Oracle Lite를 사용한분이 없네요 ㅠㅠ Pocket PC 2003 에뮬레이터 안에 Oracle Lite 설치했구요. Pocket PC 2003 에뮬레이터 안에서 인터넷도 가능하도록 셋팅하는데 성공하였습니다. 연결 문자열은 독특하게 "DSN=서비스명;uid=아이디;pwd=비밀
-
Downloading iTunes for Vista problem....
Hi all. I recently did a Factory Restore on my Gateway PC (about 8 months old). After everything was returned to the original settings, I tried to go ahead and download iTunes from Apple's website. However, everytime I hit save, the download begins a
-
Nokia Lumia 1020 and Snow Leopard
Dear People, i want to buy a new smartphone, Nokia Lumia 1020, because it has a great video camera for filming in low light, but I am afraid I will have problems importing the video files into iMovie. I use 10.6.8. . Does anybody have experience with