UCS c22 M3s + LSI MegaRaid 9265 not recognized

1.
We have this server c22 m3s
I have installed the raid card and the battery.
Altough, When I boot, I do not see any LSI prompt.
CIMC does not see anything in the storage controller section. And Yes, I did install the lastest upgrades.
What do I need to do in order to be able to use the card?
It's a Brand new server. Blank.
And no prompt for CTRL+H.
2.
What is the use of the GPIO connector from the sas cable?
Am i obligated to plug it ?

Danik,
This servers have a embedded RAID controlleri on the motherboard as well (embedded SATA-only RAID controller that supports up to four SATA-only drives <<< Does not support Virtualization OSs, like VMware) so if you bought a PCIe RAID card, you have 2 RAID controllers.
How many CPUs do you have? and where is this RAID controller installed? Controllers are installed by default in slot 1 for 1-CPU systems and slot 2 for 2-CPU systems, meaning that if there is only one CPU and the card is in slot 2, it will NOT be recognized/work, unless you change the OPROM (Option ROM) to enable another slot
See this (Table 28) for the supported installation and that shows that the embedded controller is initiallyh enabled, very likely the reason why you do not see the "Ctrl-H" option:
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/c22m3_sff_specsheet.pdf
And here is the option to change the OPROM and enable a different PCIe slot when having 2 CPUs in the system:
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/c22m3_sff_specsheet.pdf <<< Check the caveats for changing the OPROM cause you might lose the option to have a VIC card for example.
A step of last resort will be to disable any OPROM not needed (for some customer that means to disable all Option ROMs)
I hope it helps, and let us know if there is any other doubts or if this did not help, but I hoipe it does
-Kenny

Similar Messages

UCS C240 M3 LSI MegaRAID VD Info

Hello,
I did replacement a new drive form a server(about 2 days ago and new physical drive number(slot) 6),
and I check storage log about new physical disk is rebuild finish and VD state change degraded to optimal from Cisco IMC.
But virtual drive's health is "Severe Fault" and also Overall Server Status same status.
I have to experience about replacement another C-series rack type server.
but I can't understand in this case. Is it bug?or something wrong?
Server : C240 M3(Ver : 2.0(1b))
RAID Card : LSI MegaRAID SAS 9271-8i
RAID Conf : SSD 2ea -> RAID 1
SAS 4ea -> RAID 10

can you share the "Virtual drive Info" tab?
-Kenny

Configure Windows on UCs c22 M3 drives are not showing

hello all
i am configuring windows server 2008r2 on UCS c22 m3 , i have configured raid1 (default) virtual drive , drive is showing in BOOT order but when i install windows and it prompts to selct hard drive, there no drive are showing , do i need to install any driver for it? if yes then which version of driver i download, my CIMP version is 1.5(1k) kindly suggest me and help me in solving this issue.

You will have to install the drivers for the RAID card that you are using. You will have to unmount the windows ISO and mount the driver ISO to install the drivers. Then you will have to mount the windows ISO back
The driver package can be downloaded from the link below
http://software.cisco.com/download/release.html?mdfid=284444317&catid=282558030&softwareid=283853158&release=1.5(1d)&relind=AVAILABLE&rellifecycle=&reltype=latest
Thanks,
Karthic

Unable to enable HBA Card in the Cisco UCS c22 m3 server

Hi All,
I need your help desperately to setup the cisco ucs c22 m3 server in our environment. We have a C22 M3 server and I did the basic config of CIMC and we have a LSI megaraid controller connected to one of the PCIe and the other PCIe has a dual port 8gb HBA card. We installed the RAID and we can see the LSI Megaraid controller. But I cannot see the HBA card and there is noo light near the card. I hope I need to enable something so that the card should work. I tried enabling in the BIOS menu I can see the PCIe slot is enabled but I am unable to see the HBA functioning. Couldyou pleasehelp me to resolve this.

Dear Manuel,
Thanks for replying me. See the answers for your queries.
What kind of HBA card are you trying to use?
If I am not wrong we are using "Qlogic QLE2562, 8Gb dual port Fibre Channel HBA".
How many CPUs do you have installed on your server?
I opened the box and saw only 1 CPU installed. But the solution is given by CISCO pre sales. We have 2 PCIe slots configured. One for LSI RAID controller and the other with dual port Fibre Channel HBA.
Awaiting your reply.
Thanks and Regards,
Jaffer Ali

Unable to install Orable Enterprise Linux with LSI MegaRAID 8300XLP

I could not install Oracle Enterprise Linux on the PC with LSI MegaRAID 8300XLP
On the boot prompt, i typed "linux dd" with USB floppy driver, but it did not detect the driver.

I got the megaraid driver from fujitsu siemens and followed instruction from “Linux Driver for Primergy Servers” to create Linux driver image.
Note: mega_sas.ett, mega_sas.sh and mega_sas.biz
I formatted the floppy disk, then I run the script, mega_sas in Linux. The script will generate some files which need for LSI MegaRAID 8300XLP.
The three files (mega_sas.ett, mega_sas.sh and mega_sas.biz) have to be on the same directory.
RedHat 4 U4 x86 64 bits
On the boot prompt, I typed a command “linux dd ” with the LSI MegaRAID 8300 XLP driver image , and it detected the driver. I could load OS on TX150-S5.
Oracle Enterprise Linux x86 64 bit R4-U4
On the boot prompt, I typed a command “linux dd” with the same driver image which I used it on RedHat 4 U4 x86 64 bit, and it could not detect the driver.
During the installation, on the page which gives me two options for partitioning the disk,
“Automatically partition
Manually partition with Disk Druid
After I chose one of them, I clicked “Next” and I got an error message such as
“ No Drivers Found
An error has occurred – no valid devices were found on which to create new file
systems. Please check your hardware for the cause of this problem.
.

Cannot enter BIOS or boot from LSI MegaRAID SAS 9271-8i

Hello,
I have a LSI MegaRAID SAS 9271-8i installed in a C220 M3 (in PCIe1). When I go to CIMC, I can see the adapter there and I can create RAID arrays. I can set the first logical drive to be the boot drive too without a problem. If I boot from ESXi installer it will see the disks and install to them.
The problem is, the server won’t boot from the disks, and I don’t see any problems for the card’s BIOS during boot. I have disabled the on-board RAID controller.
How do I get the server to boot from the RAID card?

Hi,
Glad to see the issue is resolved now (I never saw your post before) was it that the OptionROM for the PCIe card was not enabled or the boot order was not properly set?
-Kenny

M4000 lsi 1064 can not create raid

Got an M4000.
prtdiag shows LSI-1064 controller.
00 PCI 0 2, 50, 1000 5, 1, 0 okay --, 133 scsi-pci1000,50 LSI,1064
/pci@0,600000/pci@0/pci@8/pci@0/scsi@1
# raidctl -S
0 "LSI_1064"
0.0.0 GOOD
0.1.0 GOOD
# raidctl -c c0t0d0 c0t1d0
Creating RAID volume will destroy all data on spare space of member disks, proceed (yes/no)? yes
Operation not support with volume of this level.
also can not create raid 1 from OBP.
also raid 1 deffined on a T2000 (an LSI-1064E controller) machine is not recognized by the M4000.
[M4000/M5000 Servers Product Notes|http://dlc.sun.com/pdf/820-7235-10/820-7235-10.pdf] says nothing about it except for a bug (6723202) regarding the M3000 machine.
Any Idea ?

There is no official document available which says why H/w RAID functionality is not there on Mx000 class machines.
None of the Mx000 offical document talks about the RAID functionality on these platfomrs which probably means that Sun is not supporting H/W RAID on these platform.
If you have any of these machines (Mx000 class) under a valid sun contract, you can open a ticket with Sun and verify this.

Managing the UCS C220 M3S with the UCS Manager

I have 2 new Cisco UCS C220 M3S running 2.0(3b) and 2.0(1b) connected to a UCS-FI6248UP 5.2(3)N2(2.23d) via a Intel X520-DA2. I also have both management interfaces up via a 100 meg copper connections. My issue is that I can't see these servers in the UCS Manager the UCS-B was a no brainer but the C's are not discovered, I've looked through both the CIMC and the UCS Manager and I don't see an option to change the management to the UCS Manager. I'm sure that I'm missing something since this is my first experience with the UCS C or UCS as a whole. Thanks

Hi,
Please make sure that the Set up of the UCS C-Series Server Integration with UCSM is correct. Here is the guide when you will be Configuring Single-connect to the IO Module FEXs.
You can also review the link here : Managing Rack-Mount Server.
Let me know if it helps,
Abhishek

TS140 LSI 9300-4i4e not seen in PCIe x16 (slot #1) however works in x4 (slot #3)

I have some TS140s (70A4001LUX 5U with i3-1225 v3 processor) that have tried installing a couple of different LSI 9300-4i43 12Gbps adapters that are not recognized when inserted into the PCIe x16 (e.g. slot #1).
However those cards are recognoized when inserted into the x4 slow (e.g. slot #3). Have tried various LSI 9300-4i4e (cards have most recent fw and bios) in a couple of different TS140s and see the same results. Have verified other cards working ok in the x16 slot.
In the process of updating TS140 BIOS to most recent late fall 2014 version to see if that magicly clears things up.
Has anybody else seen this and know of a resolution other than dont use the LSI 9300 in slot #1?

@I_am_Nivek thks for the info and ideas, I should have mentioned that the onboard RAID on the TS140 was not being used, in the BIOS/Setup, the ATA mode is set to AHCI (other options are IDE or RAID). Also as an FYI/FWIW, on the TS140 or at least the version that I have, the RAID/IDE/ATA is accessed via the "Devices" tab and then under the ATA section. I do recall seeing the "SCU" mode on a different Lenovo system that I have used, might have been a TD340 iirc.
However with the RAID disabled (as it had been), the adapter card still does not appear.
Regarding the boot mode, good idea, I had the TS140 in CSM which enabled both UEFI and BIOS, tried changing it to disable CSM which only allows UEFI mode. However that did not work either.
Is there a different BIOS as well as different motherboard firmware version available vs. what I am using (see above)?

USB Device for IPOD not recognized by Windows, whether ipod connected or no

During the past few days I have received a pop up error message from (I would think) Windows that the USB device is not recognized. I have the USB plug for the ipod connected (as always)but the ipod isn't even connected. It keeps popping up like every few seconds that the usb device is not recognized.
When I attach the ipod itself, the ipod is recognizing it because it powers up. But, it took 10 times just to get the ipod to recognize through itunes. It updated, then immediately upon completion, windows again starting giving repeated error messages that the usb device wasn't recognized.
I have downloaded the newest itunes but I had it on my system for 4 days with no problems whatsoever. I don't think that's it. No other system changes.
I've deleted my temp files and cache. Also did a "disk clean up" and "defrag." It's still doing it.
Any suggestions?

I'm having the same problem. Ever since I upgraded to version 7, iTunes & my PC no longer recognise my iPod, and it therefore won't sync.
It's not the USB port (other devices work in it), I rebooted my iPod and re-installed iTunes, I've tried stopping and starting the iPod Service (but can't see my iPod in My Computer). When I run the Diagnostics it says iPod connection failed. I've even bought a new USB cable but that doesn't work either.
This is driving me up the wall. Is there a glitch with iTunes 7?
Can anyone help me out?? Thanks
Windows XP

Aio Remote: PDFs not recognized by Google drive.

Aio Remote on iPad Air2 iOS 8.1.1 - I created a PDF on my iPad from my HP Envy 7640 using Aio remote app. In the files/document section it's there (3 pages) as a PDF. But when I upload a copy from Aio Remote to Google Drive it's not recognized by Google Drive as a PDF even though it has a PDF extention. I have other PDF files stored in Google drive that are perfectly fine. It must be something in your app that is the problem.

More info: if I send it from Aio remote as an email attachment to myself I get a PDF that I can upload to Google drive and Google drive reconizes it as a PDF. again proving it is Aio remote that is doing some thing wrong when uploading to Google Drive.

I recently upgraded to ios7 and now my PC is not recognizing my iphone

I am having several problems. I recently upgraded to ios7 and now my PC (Windows 7) is not recognizing my iphone. 1) I am getting an error message when itunes opens: "Itunes could not connect to the iphone because it is locked with a passcode. You must enter your passcode on the iphone before it can be used with itunes." How did it get locked and how do I unlock it without losing my data? What do they mean by passcode? I don't have a 4-number code to get into my iphone activated. In fact, I've never had a passcode.
2) I cannot download my photos from my iphone onto my computer because my computer doesn't recognize my iphone. In other words, my iphone does not show up on my computer (no iphone icon, no DCIM folder).
3) This is a separate issue but it is also very confusing: I went online to check my iCloud and I cannot see any data (icloud.com). But I know that I set up iCloud when I upgraded to ios7 and it backs up my data every night. What am I doing wrong, am I unable to see my data and photos?
Why is this happening? It was bad enough that when I upgraded to ios7, I lost my Notes - I have no idea why they didn't return. But now essentially my iphone is not recognized when connected to my computer and this is very frustrating. I have read numerous previous postings regarding downloading photos onto the PC and regarding this passcode error and cannot find a resolution, so I would appreciate any help.

No problem!
This will make it easy for you:
http://www.tuaw.com/2011/07/09/quicken-wont-run-on-lion-heres-10-mac-apps-to-cur e-those-blue/

I an getting an error with photo merge in PS cc . It gives me a code tmp00000001 using from photoshop and if I try from bridge it tell me that I need to select more than one image. It is not recognizing the photos I am selecting in bridge. please help. my

A new problem with CS5 forced me to download PScc but the problem is still there. I am getting tmp00000001 in photo merge when importing multiple files from inside PS and if trying from bridge I am getting a pop up box telling me I need to select more than 1 file. Photoshop potomerge is not recognizing my selections from bridge..!! please help.. my knowledge of computers is a 3 on a scale of 1-10

if i run this particular code
( SELECT
AccountDetails.CUSTOMERNUMBER, AccountDetails.ACCOUNTNUMBER, CUSTOMERDETAILS.CDTITLE, CUSTOMERDETAILS.CDFIRSTNAME, CUSTOMERDETAILS.CDLASTNAME, AccountDetails.ACCOUNTTYPE,
AccountDetails.ORIGINALCONTRACTENDDATE, AccountDetails.CONTRACTTERM, AccountDetails.CONTRACTENDDATE, AccountDetails.BRANCHAREA, AccountDetails.PRODUCTTYPE,
AccountDetails.HOUSEBANKACCOUNT, AccountDetails.CARMODEL, AccountDetails.CARLICENCE, AccountDetails.ARREARSBALANCE, AccountDetails.CODEBTOR, AccountDetails.GUARANTORNUMBER
FROM AccountDetails
JOIN CUSTOMERDETAILS ON AccountDetails.CUSTOMERNUMBER = CUSTOMERDETAILS.CUSTOMERS1
WHERE EXISTS
( SELECT *
FROM Dcaaccountallocation
JOIN DebtEpisodes ON DebtEpisodes.ACCOUNTID = Dcaaccountallocation.ACCOUNTID
WHERE Dcaaccountallocation.dcaid = 41
AND Dcaaccountallocation.status = 2
AND DebtEpisodes.DCASentDate IS NULL
AND Dcaaccountallocation.ACCOUNTID = AccountDetails.ACCOUNTNUMBER
AND DebtEpisodes.DCAORLAWYER = 'DCA'
This returns 1 row of data
However if i run a small part of the above code...
SELECT *
FROM Dcaaccountallocation
JOIN DebtEpisodes ON DebtEpisodes.ACCOUNTID = Dcaaccountallocation.ACCOUNTID
WHERE Dcaaccountallocation.dcaid = 41
AND Dcaaccountallocation.status = 2
It returns a lot of rows with a status of 2
Now i presume what I am going to do is to ensure that all the fields provide satisfactory requirements, with regards to the above code. Although I have many records in all the stated tables already.
:(

IPod nano does not charge & is not recognized by computer or iTunes

I have a 1st generation nano 1 GIG.
It appears "dead."
It is not recognized by My Computer, iTunes or the Ipod Updater (The updater asks that I connect the iPod, which I do). The iPod diagnostics through iTunes also reports that my iPod is not connected.
I have tried my iPod on 4 different machines, with one of them having USB 2.0.
I tried the following from Jeff Bryan. (I don't know if the links from his post have carried over into this post.) So I will list the things I have tried near the end of this post.
- My iPod won't turn on.
- iPod battery doesn't charge.
- iTunes 7 doesn't recognize the iPod.
- Your Windows PC doesn't recognize iPod.
- iPod appears in Windows Explorer but does not appear in iTunes.
- iPod does not appear in iTunes.
- Fast user switching in Windows XP is not supported.
I tried resetting my iPod by switching the Hold button on and off and then pressing Menu and the Select button for 6-10 seconds. I have done this over and over and over.
I have uninstalled the latest iTunes, reboot, reinstall - same problem.
I have stopped the iPod service, plugged in the iPod, but it isn't recognized by My Computer as stated in the Apple Do-It-Yourself Help. I launched iTunes - same problem.
I used the window cleanup utility, reboot, reinstall iTunes, connect iPod - same problem.
I have used the Windows ipconfig utility to change my boot parameters, but still nothing.
If anyone has any ideas, I would greatly appreciate them.
My iPod is just shy of 6 months.
I do have a replacement contract with Best Buy - but I would like to cover all the bases before I succumb to defeat.
Thanks
XP Home with USB 1.1 Windows XP 4 machines, all XP, 2 XP Pro, 2 XP Home, 3 have USB 1.1, 1 has USB 2.0, 2 machines have latest iTune

I'm having the same problem, my ipodnano is about a year old and I can't figure out what to do. I just installed the new itunes on my new laptop with vista premium. I'm desperate for a resolution, do you have any suggestions at all. Any help is greatly appreciated. Thank you

Iphone not recognized by windows or itunes

Can anyone please help me figure out how to resolve this issue? My iphone 4 is not recognized by my PC. My OS is by Vista Home Premium Service Pack 2. I tried the various "device not recognized" troubleshooting to no avail. I tunes is up to date. I even turned off my security sw for a bit to see if there was a third party conflict...all to no avail. There has got to be someone out there who has the smarts to show me how to fix this. Please advise and many thanks in advance!

Jason,
I understand why Apple doesn't cover the water damaged phones under the warranty, but do you know why they don't fix them if the customer is paying? Is it just because they want the people to buy another phone so they can make more money? I guess I just don't get it.
The cost to repair a device and all of its components is more than the cost of a new device.
Other than the article I linked above, this is the part of the warranty/legal forms that would apply:
+"US v1.0+
+Apple reserves the right to refuse+
+service on products that have serial numbers altered, defaced or removed or that are damaged due to+
+accident, abuse, neglect, misuse (including faulty installation, repair, or maintenance by anyone other+
+than Apple or an Apple Authorized Service Provider), unauthorized modification, extreme environment+
+(including extreme temperature or humidity), extreme physical or electrical stress or interference,+
+fluctuation or surges of electrical power, lightning, static electricity, fire, acts of God or other external+
+causes. In such event, Apple may return the product to you without servicing it, and may charge you the+
+Diagnostic Fee."+ from http://images.apple.com/legal/terms/repair/docs/070108aiphoneOOW.pdf
-Jason

UCS c22 M3s + LSI MegaRaid 9265 not recognized

Similar Messages

Maybe you are looking for