Update OSX 10.2.8 Build 6R73 repeatedly fails to install.

Hi,
I have an elderly but beloved iBook, 900Mhz Power PC G3 with 640 Mb.
I have just replaced the failed hard drive and I have used the disks that came with the iBook to install OSX 10.2.1. I have successfully installed some updates e.g. Quicktime 6.2, Safari 1.0 and Battery 1.1. However the major Mac OSX Update Combined 10.2.8 Update Build 6R73 (100 Mb) has failed after several attempts.
The message says unhelpfully "The installation encountered a problem".
I have successfully run the iBook Apple Hardware test SW version 1.2.4.
What now?
As always any advice will be treasured.
Thanks
Silver6d

It's been a long time since I encountered this so bear with me--lost a few brain cell to some darned fine microbrews since then!:
Some G3 Macs did not take to the "big leap" of going from the Jag base (10.2.1 in you case and 10.2.3 in the case of my retail install set). We often had to bring the OS level up gradually.
To get one of my G3s fully updated after an Archive & Install. I ended up doing this via downloads, not automatic updates;
base: 10.2.3 from retail install disk set
step 1: d/l and install 10.2.4 incremental (not "combo")
step 2: d/l and install 10.2.6 incremental
Step 3: d/l and install 10.2.8 combo
There was an older build of 10.2.8 that was a beast but I think it's been off the servers for years. You should be OK with build 6R73. As your base is lower than mine, you may need to find 10.2.2 and 10.2.3 incremental updaters also.

Similar Messages

IE 10 Update 2977629 on Windows 7 x64 SP1 repeatedly fails to install.

IE 10 Update 2977629 on Windows 7 x64 SP1 repeatedly fails to install with error code 214794205 "Access is Denied". This update is being run using an administrator account. This is a systemic issue on all domain joined systems, desktops
not in a domain are not affected. I cannot find any guidance on how to fix this, please help!

Hi,
Based on your description, ED's suggestion is available. You could use gpresult command to export the group policy settings to check if there any group policy affect the installation.
About how to use it, please read the guide below:
How to Use the Group Policy Results (GPResult.exe) Command Line Tool
http://technet.microsoft.com/en-us/library/bb456989.aspx
If it's not helpful, please provide the Windows Update installation log in order to analyze it.
You could find it from the following path:
%windir%\Windowsupdate.log
Karen Hu
TechNet Community Support

KB2977326 - Security Update for SQL Server Service Pack 1 repeatedly fails to install

This update fails to install every day when I shut down my computer. Here is the WindowsUpdate.Log:
2014-12-02 15:50:11:469
420 44c
AU #########
2014-12-02 15:50:11:469
420 44c
AU # Initiating install at shutdown
2014-12-02 15:50:11:469
420 44c
AU # Approved updates = 1
2014-12-02 15:50:11:516
420 44c
AU <<## SUBMITTED ## AU: Install updates / installing updates [CallId = {685C12BB-7AA9-4A31-9620-8F306EEE31C3}]
2014-12-02 15:50:11:516
420 44c
Shutdwn InstallAtShutdown starts.
2014-12-02 15:50:11:516
420 1528
Agent *************
2014-12-02 15:50:11:516
420 1528
Agent ** START ** Agent: Installing updates [CallerId = AutomaticUpdates]
2014-12-02 15:50:11:516
420 1528
Agent *********
2014-12-02 15:50:11:516
420 1528
Agent * Updates to install = 1
2014-12-02 15:50:11:531
420 1528
Agent * Title = Security Update for SQL Server 2012 Service Pack 1 (KB2977326)
2014-12-02 15:50:11:531
420 1528
Agent * UpdateId = {E0D65CC4-3B13-4352-BD89-A28C5F4C5017}.200
2014-12-02 15:50:11:531
420 1528
Agent * Bundles 1 updates:
2014-12-02 15:50:11:531
420 1528
Agent * {C076E757-1A4F-44DB-823B-CFFC07CD7D38}.200
2014-12-02 15:50:11:547
420 16d8
Shutdwn InstallAtShutdown got install progress.
2014-12-02 15:50:12:327
420 d4c
Report CWERReporter finishing event handling. (00000000)
2014-12-02 15:50:20:548
420 44c
AU WARNING: Pending directive, 'Install Approval', is not applicable
2014-12-02 15:50:24:417
420 16d8
Shutdwn InstallAtShutdown got install progress.
2014-12-02 15:50:24:432
420 16d8
Shutdwn InstallAtShutdown got install progress.
2014-12-02 15:50:24:432
420 1528
DnldMgr Preparing update for install, updateId = {C076E757-1A4F-44DB-823B-CFFC07CD7D38}.200.
2014-12-02 15:50:25:119
2052 608
Misc =========== Logging initialized (build: 7.6.7600.320, tz: -0600) ===========
2014-12-02 15:50:25:119
2052 608
Misc = Process: C:\Windows\system32\wuauclt.exe
2014-12-02 15:50:25:119
2052 608
Misc = Module: C:\Windows\system32\wuaueng.dll
2014-12-02 15:50:25:119
2052 608
Handler :::::::::::::
2014-12-02 15:50:25:119
2052 608
Handler :: START :: Handler: Command Line Install
2014-12-02 15:50:25:119
2052 608
Handler :::::::::
2014-12-02 15:50:25:119
2052 608
Handler : Updates to install = 1
2014-12-02 15:50:25:119
420 16d8
Shutdwn InstallAtShutdown got install progress.
2014-12-02 15:52:23:991
420 44c
AU AU setting next sqm report timeout to 2014-12-03 21:52:23
2014-12-02 15:54:39:587
2052 608
Handler : WARNING: Command line install completed. Return code = 0x84b20001, Result = Failed, Reboot required = false
2014-12-02 15:54:39:587
2052 608
Handler : WARNING: Exit code = 0x8024200B
2014-12-02 15:54:39:587
420 16d8
AU >>## RESUMED ## AU: Installing update [UpdateId = {E0D65CC4-3B13-4352-BD89-A28C5F4C5017}]
2014-12-02 15:54:39:587
2052 608
Handler :::::::::
2014-12-02 15:54:39:587
2052 608
Handler :: END :: Handler: Command Line Install
2014-12-02 15:54:39:587
2052 608
Handler :::::::::::::
2014-12-02 15:54:39:587
420 16d8
AU # WARNING: Install failed, error = 0x80070643 / 0x84B20001
2014-12-02 15:54:39:587
420 16d8
Shutdwn InstallAtShutdown got install progress.
2014-12-02 15:54:39:711
420 1528
Report REPORT EVENT: {DFA9CDC8-334A-4E57-9588-77B8E980833D}
2014-12-02 15:54:39:587-0600 1
198 101
{E0D65CC4-3B13-4352-BD89-A28C5F4C5017}
200 80070643
AutomaticUpdates Failure
Content Install Installation Failure: Windows failed to install the following update with error 0x80070643: Security Update for SQL Server 2012 Service Pack 1 (KB2977326).
2014-12-02 15:54:39:727
420 1528
Report CWERReporter::HandleEvents - WER report upload completed with status 0x8
2014-12-02 15:54:39:727
420 1528
Report WER Report sent: 7.6.7600.320 0x80070643 E0D65CC4-3B13-4352-BD89-A28C5F4C5017 Install 101 Unmanaged
2014-12-02 15:54:39:727
420 1528
Report CWERReporter finishing event handling. (00000000)
2014-12-02 15:54:39:805
420 1528
Agent *********
2014-12-02 15:54:39:805
420 16d8
AU Install call completed.
2014-12-02 15:54:39:805
420 1528
Agent ** END ** Agent: Installing updates [CallerId = AutomaticUpdates]
2014-12-02 15:54:39:805
420 16d8
AU # WARNING: Install call completed, reboot required = No, error = 0x00000000
2014-12-02 15:54:39:805
420 1528
Agent *************
2014-12-02 15:54:39:805
420 16d8
AU #########
2014-12-02 15:54:39:805
420 16d8
AU ## END ## AU: Installing updates [CallId = {685C12BB-7AA9-4A31-9620-8F306EEE31C3}]
2014-12-02 15:54:39:805
420 16d8
AU #############
jim...

Hello,
Please examine the Summary.txt log file. The following article may help you locate the file on disk:
http://msdn.microsoft.com/en-us/library/ms143702(v=sql.110).aspx
If you find the sentence “A failure was detected for a previous installation” on the Summary.txt log file, please repair SQL Server using the following article:
http://msdn.microsoft.com/en-us/library/Cc646006(v=sql.110).aspx
If you find other errors, please share the content of the Summary.txt log file with us.
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com

HT1338 I am currently struggling to update OSX mountain lion to 10.8.4, I have installed the update, and it is telling me that a restart is required. When I restart the mac it is still showing that I have one update outstanding, and it is for 10.8.4. can

I am currently struggling to udate OSX mountain lion to 10.8.4, it constantly tells me that an update is available and a restart is required. Please could someone help?

Click here and download it.
(86298)

Why does Acrobat Pro 11.0.7 updates repeatedly fail to install?

Why am I suddenly getting the error every time autoupdate runs? This just started. I tried uninstalling as directed. When I try to download my previously purchased COMPLETE application, nothing happens. Downloading from the Adobe site gives me an application that Adobe wants me to spend $14 on EVERY month. I've already paid for this application once - I'll be damned if I will pay again. I run Mavericks 10.9.5. Has anyone else had this problem? Does anyone have a solution?

Try http://www.adobe.com/support/downloads/product.jsp?product=1&platform=Windows (or MAC). With XI, you just go ahead and install the latest. It indicates the update applies to any previous updates. For previous versions of Acrobat. most of the updates had to be installed in order. When you do the installation, be sure to be logged in as the administrator (as when you installed the original XI) and have anti-virus disabled.

Security Update (KB954430) repeatedly fails to install (Code 64C)

Things I have tried:
- hotfix tool
- disabling virus protection
- downloading and manually installing the update (Error: the feature you are trying to use is on a network resource that is unavailable.)
- downloading and running this update: Windows6.1-KB947821-v34-x64.msu
- update from Windows Install DVD (I think this is called an in-place install)
I fear I will have to format and reinstall Windows and all my programs. Is there anything else I can try? Is it terribly risky to simply continue working without this update?

Method 1:
Follow the instructions in the link below to rename Software distribution and catroot folders and try to install the service pack.
You cannot install some updates or programs
http://support.microsoft.com/kb/822798
Method 2:
Follow the instructions in the link below to reset Windows update components.
How do I reset Windows Update components?
http://support.microsoft.com/kb/971058
Method 3:
Perform System File Checker (SFC) scan which will help you in resolving the issue.
To determine whether the issue that you are experiencing is caused by one or more system files that are used by Windows Vista, run the System File Checker tool. The System File Checker tool scans system files and replaces
incorrect versions of the system files by using the correct versions.
Follow the instructions in the link below to run SFC scan.
http://support.microsoft.com/kb/936212/
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

I am attempting to install flash player on Mac OSX 10.9. I have repeatedly downloaded and installed according to directions but it tells me: "Before viewing PDF docs in this browser you must launch Adobe reader and accept End User License Agreement then q

See above

Hello,
At which point during the Flash Player installation process are you prompted to open a browser to view a PDF document?
Can you verify if Flash Player is successfully installed by visiting http://helpx.adobe.com/flash-player.html?
Thank you.
Maria

Update 9.0.2 to Acrobat 9 Pro fails to install

Am trying to update Adobe Acrobat 9 Pro, and the update fails to install

Normally you would do the updates from the Help>Updates menu from within Acrobat. Sometimes the server has issue or other problems come up and the updates do not work for some reason. The current level of AA 9 is 9.5.5. To do the updates manually, go to http://www.adobe.com/support/downloads/product.jsp?product=1&platform=Windows (similar for MAC, but you did not state the OS), download from the latest to the earliest. The reason for this order is to note with each update the previous update that is needed. Then install the updates in order. You only have to reboot after the last update.

.ipa from builder V28 always failed to install

Hi,
I have problem to Install my reader on my testing iPad with OS6 & OS7,
i already build my reader form Adobe DPS V28, and download the .ipa with my developer certificate, and before i submitted to appstore i want to try to testing, but everytime i try to Install and sync to my ipad it always failed, did i do something wrong when i build the reader?
Thank You

Does the mobileprovision file you used include the iPad's UDID? If not, you can't install the app on that device.

TS2776 I want to sync my iPhone 4 to my PC itunes but trying to upgrade and repeatedly failing to install version 10.6.3.

I want to sync and transfer songs from my PC to my iPhone 4 but the original itunes version was not compatible and I repeatedly found the latest 10.6.3 would not install.
I tried an earlier version 10.3 allegedly suitable for iPhone and although it actually installed no syncing waas possible!
Any ideas

I repeatedly found the latest 10.6.3 would not install.
Do you get an error message when you try to install iTunes? If so, what does it say? (Precise text, please.)

InDesign crashing, newest update fails to install

Is anyone else having trouble with InDesign crashing, and the newest update fails to install?
I have uninstalled InDesign, restarted my macbook, reinstalled, and then tried the update, which says it has an error and fails to install. The current version crashes after asking it to do anything after opening the programme, such as opening a file or trying to select any of the menus.
I use a Wacom Bamboo tablet: could this have anything to do with it? A colleague had a similar issue with Illustrator and the Wacom driver. Would this affect the update installation?
Help appreciated!

Yes, I have just had the same problem on my Spectre X360

Windows failed to install the following update with error 0x80070005

Hi,
We are using Win Server 2008 R2 std. Server and Win 7 Professional X64 clients. During the second batch of update we got an Error while updating on one client machine and the system restoring back automatically However other clients are updating and working
fine. Then i tried to install the updates one by one manually then successfully installed all the updates except one ie. KB2862330. It keeps failing then i found an article suggest to check the update with Admin Previlage, disable Antivirus and Scan the
computer for Malware (Using MS Security Scanner and Malwarebytes). I tried both but never works. After that i got 2 batch of updates, everything is updating and trying to update this (KB2862330) and failing till date. What is the issue and why its not updating
on one machine?
Installation Failure: Windows failed to install the following update with error 0x80070005: Security Update for Windows 7 for x64-based Systems (KB2862330).
KB Article Followed : http://support.microsoft.com/kb/968003/en-us

Okay, good. The SURT shows no errors.
So now we can blame the problem exclusively on the update itself.
And yes... there are still known, ongoing issues with KB2862330.
Truly, my suggestion is to just not install it at all. Unless you've identified a known risk via a USB vector on particular systems where the vulnerability would be considered a critical risk, I'd say that the risk caused by the vulnerability is significantly
less than the risk of additional headache caused by the update itself. I have still not deployed MS13-081 to any of my systems, and frankly, I don't plan to.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

MS Office 2010 Updates failing to install

Hi,
We have 9 MS Office 2010 updates released in April 14th 2015, that are failing to install on a Windows 7 machine. WindowsUpdate.log file shows and error message as "Windows failed to install the following update with error 0x80070656" , for all
the 9 updates.
Tried to restart the system and install updates again, which failed.
Please suggest how to proceed on this.
Regards, Lorin Davis

in addition to/instead of restarting the client, try this on the client:
1. stop the windows update and background intelligent transfer services
2. delete everything in c:\windows\softwaredistribution
3. start the windows update and background intelligent transfer services
4. go back into windows updates in the control panel and check for updates again. or run "wuauclt /detectnow" from a command prompt.

Hey i have a old powerbook G4 laptop and i was wondering where can i download the OS ( Mac OSX 10.5.8 Build ( 9L30 ) to do a fresh install my system is running really slow is there any place where i can down load this OS?

Hey i have a old powerbook G4 laptop and i was wondering where can i download the OS ( Mac OSX 10.5.8 Build ( 9L30 ) to do a fresh install my system is running really slow is there any place where i can down load this OS?

Hello,
Unfortunately Apple do not offer a download for mac OS X 10.5.8. They will only provide updates available for download. ( Normally you would do so once the OS is installed)
To do a fresh install of this software your going to need to buy a retail copy of the disk.
There are some vendors who do still stock the media disk, but they can be expensive.
Best of luck.

After effect 7 pro crash after update osx to 10.4.7

Topic
After effect 7 pro crash after update osx to 10.4.7
Robinmaster - 03:53am Aug 2, 2006 Pacific
Hi all write this messages bacouse i have a problem with start up of my AE 7 pro. AE7 pro crash when boot after initialization of GUI. try remove a open gl plug but not resolved e problem..
E error is
Date/Time: 2006-08-02 12:44:19.674 +0200
OS Version: 10.4.7 (Build 8J2135)
Report Version: 4
Command: After Effects
Path: /Applications/Adobe After Effects 7.0/Adobe After Effects 7.0.app/Contents/MacOS/After Effects
Parent: WindowServer [57]
Rosetta: Yes
Version: 7.0 (7.0)
PID: 2356
Thread: 0
Exception: EXCBADINSTRUCTION (0x0002)
Code[0]: 0x00000001
Code[1]: 0x00000000
Please help me.. i'm deprived of hope..
Th's
N.B i work with MAC BOOK PRO (intel ) with 2 GB of ram

Hi there, same problem here but on a PowerPC.
I just bought AE7 and installed it on my G5 (with then 10.3.7 running on it). Install went fine but the application would not start up.
Thought this might be a good time to clean up and installed fresh new system on this G5, updated it to 10.3.8 and first thing: installed AE7 again.
But: same problem. In fact, all Adobe application will not start up! The icon bounces a little and then nothing but a crash report.
For a moment I thought I had the solution, because I disabled all the "user fonts". Everything worked fine. Then I installed, as before, my Apple applications (Final Cut Pro, DVD Studio Pro, etc) and, oh no... same problem over again. The Adobe application will not start up!
Tried to disable all non essential fonts: no cure. This is driving me crazy....
Any suggestions?
Date/Time: 2006-10-14 15:43:31.127 +0200
OS Version: 10.4.8 (Build 8L127)
Report Version: 4
Command: After Effects
Path: /Applications/Adobe After Effects 7.0/Adobe After Effects 7.0.app/Contents/MacOS/After Effects
Parent: WindowServer [108]
Version: 7.0 (7.0)
PID: 733
Thread: 0
Exception: EXCBADACCESS (0x0001)
Codes: KERNPROTECTIONFAILURE (0x0002) at 0x00000000
etc etc etc...

Update OSX 10.2.8 Build 6R73 repeatedly fails to install.

Similar Messages

Maybe you are looking for