[Urgent]How can I write to physical memory by using LabVIEW 8.2??

Hi everybody,
I am dealing with a project related to micro-EDM. We feed the gap voltage back to a NI DAQ card (not quite sure about the series number, might not be important to this problem), and we want to use this voltage to determine the command position of the motor, which is controlled by a Delta Tau PMAC motion controller. Now the problem is, the NI DAQ card and Delta Tau PMAC controller cannot communicate directly with each other. Therefore, we want the LabVIEW to write the value of voltage to a certain physical memory address, and then let the PMAC controller read that address. Is this feasible by using LabVIEW and NI-DAQ card? Which block or library in LabVIEW shall I use to achieve that? Or is there any alternative way to do it? Thanks a million!
I have to get this done by the end of this week....if you know how to do it, please let me know. I really appreciate it! You are my lifesavor!
Regards,
Xiaofei

Duplicate post: http://forums.ni.com/ni/board/message?board.id=170&thread.id=289539&jump=true
LabVIEW Champion . Do more with less code and in less time .

Similar Messages

How can i write the data to PIC16F819 using labview?

how can i write the data to PIC16F819 using labview?
Need help!
im using labview in gathering the datas that i need to right to the PIC, then after getting all the datas i am using another program which is ICD2 in order to write it to the PIC. Is it possible to do this task through LV? coz we are spending a lot of time transferring the data from LV to ICD2 manually and its prone to mistake as well.
any suggestion?
thanks,
Pedz

LabVIEW does not currently have a built-in method to communicate with
i2c, but there are other vendors that sell devices to communicate in
this manner with LabVIEW development kits. One that I know of is
from MCC... here is a link: http://www.mcc-us.com
They sell a device called iPort, and then you can buy LabVIEW VIs to go with it. I hope this is helpful to you!
john m

How can I write to the parallel port using LabVIEW 6.0.2

I have tried updating the labview.ini file and also using the parallel.llb available on the site. When I execute the program it gives me error 37 saying,"device not found". I am running this code on windows 98. I tried to use VISA write,serial port write (using port 10) but nothing seems to work. I also tried to develop a sample code using inPort and outPort, but no success, it is not able to read the data back from the parallel port, even if it seems (????i don't know any way to cross-check it though????) to write.
Does anybody know the problem here?
THanks.
Pari.

Thanks Brian.
Well here is the next problem. I got a VI (attatched) off ni.com and it works fine on a windows98 platform. But quits working on NT.
I can write perfectly (which i checked by hooking an LED display unit at the other end of the parallel port cable). I observed that the LEDs respond to the toggling of individual bits (data bits). But the error occures at the "out port.vi", when I try to run it on a NT machine (where I actually wanna use it). Are you aware of any changes to be made in order to run a VI on NT that works on 98?
Thanks again.
Pari.
Attachments:
parallelPortSwitcher.vi ‏124 KB

How can I write an iBook review without using iTunes?

I have a problem on how can I write a review on an iPad book or iBook without using iTunes. Some of my friends are also asking me on how can I write a review on an iBook without using iTunes. I am on dilemma and I need your help to solve this problem. I hope you can respond soon if possible. Thanks.

Simple, you cannot. You can only post reviews through the store front gateway.
Well, actually, you can write the review in any editor or tool you wish to use, but to post it, you have to login to the store account. If you do not have an AppleID and store account, you cannot post a review.

How can you create a test plan generator using labview

I am looking to create a testplan generator using labview to help RF Engineers translate test requirements into test parameters and wanted to know how i can go about it.

Have you considered to use Teststand? Teststand organizes all the tests and allows to parameterize them.
Creating a tool with a similar functionality will be more expensive than buying Teststand and modifing the operator interface.
Waldemar
Waldemar
Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
Don't forget to give Kudos to good answers and/or questions

How can I test IRIG-B'a accuracy using Labview

We have a GPS source as reference, how can we test second GPS clock with IRIG-B output ? Can we by using Labview ?

Most timecode generators work by taking an external input (GPS, IRIG, PPS, or any of a number of other timecodes such as MILA, NASA36, IRIG A, etc) and outputting an on-time signal.
The most common systems now use a GPS receiver to steer an oscillator to some fixed frequency (10MHz is a favorite) and then use that steered oscillator to generate the outputs. The one PPS from a GPS receiver is not very smooth and jumps around easily a few hundred nano-seconds every PPS (at least they used to).
Time codes are usually done by generating an on-time digital signal in which the rising edge of the frame bits is co-incident with the PPS timing. The digital signal is then sent through some analog magic (op amps and whatever) which delays the output on time.
In digital signals, the rising edge is considered on time, in analog it is the zero-crossing.
Good systems will calibrate out the analog delay in the factory by moving back the on-time timing that is fed to the analog so that all on-time marks are co-incident.

URGENT : How to give W3 command to DRC 91C using LabView

Hi,
I am very new to LabView and this is the first assignment that i need to carry out.
I need to set the DRC 91C Heater % to 20 by creating a program using LabView.
I tried placing an DRC 91C control on the front panel. Now how to use it.
Can someone help?
I have read the Manual for DRC 91C from Lake Shore but it only mentions what parameters to use to execute W3.
But where should i give there parameters (N1N2N3,N4N5N6,N7N8N9,N10,N11N12N13) .
Any type of info will be helpfull.
Please Guide a bit.
Regards,
Shriniket Sarkar

Please refer to table 4-9 and 4-10 page 4-14,4-15. The N(x) denotes a number
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

How can I measure coherence between EEG signals using labview?

well, I have an EEG signal(a matrix 16X8498)whose lines represent the channels and collums the samples. The last line is the stimulus channel. I would like to know if I can measure the coherence between my EEG channels(lines)using labview.If,yes,is there someone who has the block diagram?

Search the Labview help for coherence and you'll find several functions (in Labview 6.1 Full Development System). The functions are in the palette Analyze >> Waveform Measurements >> Frequency Response Function (Mag-Phase) or (Real-Im).

How to get the size of physical memory by using system call ?

how to get the size of physical memory by using system call ?What system call can be used for me to get the size of physical memor? thanks.

%vmstat 3
procs memory page disk faults cpu
r b w swap free re mf pi po fr de sr s0 -- -- -- in sy cs us sy id
0 0 0 3025816 994456 4 19 6 0 0 0 0 8 0 0 0 459 253 139 1 1 99
0 0 0 2864688 777408 0 2 0 0 0 0 0 3 0 0 0 428 134 175 0 1 99
0 0 0 2864688 777408 0 0 0 0 0 0 0 7 0 0 0 448 112 166 0 0 100
one interesting observation about vmstat I found out is (mostly on Solaris)
the first line of information always off chart, so I usually do a few interval to get constant result.
if you use linux
just
cat /proc/meminfo

How can i write a code to get sume of value from days.

Hi,
how can i write a code to get the sum of value of days(example 1 to 30).
This is in BPS ...
i created multi planning area and creted planning function with {keyfigure name,planning area,days}.
now i want to read all the actual values from basic planing area(basic cube) and calculate the sum of the value.if you have idea can you share the code.
ENTRIES = VARC ( 'zvardays' ).     ex(zvardays like 28 days or 29 days or 30 days or 31 days)
COUNT = ENTRIES.
*Get the all the days value from actual
FOREACH PAREA = 'basic planning area'.
COUNT = 1.
DO
     SUM = SUM + {amount, count}      (amount is a keyfirgure value)
ENDDO.
COUNT = COUNT+1.
   SUMACT = SUM.
ENDFOR.
can you correct the above code ....to read the values and sum of the those value.
Thanks...

Hi ..
That is ok..
Can you provide sample code for my requirement..
and also how can i pass the error message (can you help me syntax )
and if my acutal-total is not equal to plan-total then
i have to pass the error message and then i have to restrict save the data how i can i restrict(user can not save the data until the values should be equal) .
Can you help me it is very urgent..
thanks.//
Edited by: Eyda rose on Jun 4, 2008 9:29 PM

How can i write a string into a specified pos of a file?

How can i write a string into a specified pos of a file without read all file into ram and write the whole file again?
for example:
the content of file is:
name=123
state=456
i want to modify the value of name with 789
(write to file without read all file into ram)
How can i do it? thank you

take this as an idea. it actually does what i decribed above. you sure need to make some modifications so it works for your special need. If you use it and add any valuable code to it or find any bugs, please let me know.
import java.io.*;
import java.util.*;
* Copyright (c) 2002 Frank Fischer <[email protected]>
* All rights reserved. See the LICENSE for usage conditions
* ObjectProperties.java
* version 1.0, 2002-09-12
* author Frank Fischer <[email protected]>
public class ObjectProperties
     // the seperator between the param-name and the value in the prooperties file
     private static final String separator = "=";
     // the vector where we put the arrays in
     private Vector PropertiesSet;
     // the array where we put the param/value pairs in
     private String propvaluepair[][];
     // the name of the object the properties file is for
     public String ObjectPropertiesFileName;
     // the path to the object'a properties file
     public String ObjectPropertiesDir;
     // reference to the properties file
     public File PropertiesFile;
     // sign for linebreak - depends on platforms
     public static final String newline = System.getProperty("line.separator");
     public ObjectProperties(String ObjectPropertiesFileName, String ObjectPropertiesDir, ObjectPropertiesManager ObjectPropertiesManager)
     //     System.out.println("Properties Objekt wird erzeugt: "+ObjectPropertiesFileName);
          this.ObjectPropertiesFileName = ObjectPropertiesFileName;
          this.ObjectPropertiesDir = ObjectPropertiesDir;
          // reference to the properties file
          PropertiesFile = new File(ObjectPropertiesDir+ObjectPropertiesFileName);
          // vector to put the param/value pair-array in
          PropertiesSet = new Vector();
     //     System.out.println("Properties File Backup wird erzeugt: "+name);
          backup();
     //     System.out.println("Properties File wird eingelesen: "+PropertiesFile);
          try
               //opening stream to file for read operations
               FileInputStream FileInput = new FileInputStream(PropertiesFile);
               DataInputStream DataInput = new DataInputStream(FileInput);
               String line = "";
               //reading line after line of the properties file
               while ((line = DataInput.readLine()) != null)
                    //just making sure there are no whitespaces at the beginng or end of the line
                    line = cutSpaces(line);
                    if (line.length() > 0)
                         //$ indicates a param-name
                         if (line.startsWith("$"))
                              // array to store a param/value pair in
                              propvaluepair = new String[1][2];
                              //get the param-name
                              String parameter = line.substring(1, line.indexOf(separator)-1);
                              //just making sure there are no whitespaces at the beginng or end of the variable
                              parameter = cutSpaces(parameter);
                              //get the value
                              String value = line.substring(line.indexOf(separator)+1, line.length());
                              //just making sure there are no whitespaces at the beginng or end of the variable
                              value = cutSpaces(value);
                              //put the param-name and the value into an array
                              propvaluepair[0][0] = parameter;
                              propvaluepair[0][1] = value;
                         //     System.out.println("["+ObjectPropertiesFileName+"] key/value gefunden:"+parameter+";"+value);
                              //and finaly put the array into the vector
                              PropertiesSet.addElement(propvaluepair);
          // error handlig
          catch (IOException e)
               System.out.println("ERROR occured while reading property file for: "+ObjectPropertiesFileName);
               System.out.println("ERROR CODE: "+e);
               // System.out.println("in ObjectProperties");
     // function to be called to get the value of a specific paramater 'param'
     // if the specific paramater is not found '-1' is returned to indicate that case
     public String getParam(String param)
          // the return value indicating that the param we are searching for is not found
          String v = "-1";
          // looking up the whole Vector
          for (int i=0; i<PropertiesSet.size(); i++)
               //the String i want to read the values in again
               String s[][] = new String[1][2];
               // trying to get out the array from the vector again
               s = (String[][]) PropertiesSet.elementAt(i);
               // comparing the param-name we're looking for with the param-name in the array we took out the vector at position i
               if (s[0][0].equals(param) == true)
                    //if the param-names are the same, we look up the value and write it in the return variable
                    v = s[0][1];
                    // making sure the for loop ends
                    i = PropertiesSet.size();
          // giving the value back to the calling procedure
          return v;
     // function to be called to set the value of a specific paramater 'param'
     public void setParam(String param, String value)
          // looking up the whole Vector for the specific param if existing or not
          for (int i=0; i<PropertiesSet.size(); i++)
               //the String i want to read the values in again
               String s[][] = (String[][]) PropertiesSet.elementAt(i);
               // comparing the param-name we're looking for with the param-name in the array we took out the vector at position i
               if (s[0][0].equals(param) == true)
                    //if the param-names are the same, we remove the param/value pair so we can add the new pair later in
                    PropertiesSet.removeElementAt(i);
                    // making sure the for loop ends
                    i = PropertiesSet.size();
          // if we land here, there is no such param in the Vector, either there was none form the beginng
          // or there was one but we took it out.
          // create a string array to place the param/value pair in
          String n[][] = new String[1][2];
          // add the param/value par
          n[0][0] = param;
          n[0][1] = value;
          // add the string array to the vector
          PropertiesSet.addElement(n);
     // function to save all data in the Vector to the properties file
     // must be done because properties might be changing while runtime
     // and changes are just hold in memory while runntime
     public void store()
          backup();
          String outtofile = "# file created/modified on "+createDate("-")+" "+createTime("-")+newline+newline;
          try
               //opening stream to file for write operations
               FileOutputStream PropertiesFileOuput = new FileOutputStream(PropertiesFile);
               DataOutputStream PropertiesDataOutput = new DataOutputStream(PropertiesFileOuput);
               // looping over all param/value pairs in the vector
               for (int i=0; i<PropertiesSet.size(); i++)
                    //the String i want to read the values in
                    String s[][] = new String[1][2];
                    // trying to get out the array from the vector again
                    s = (String[][]) PropertiesSet.elementAt(i);
                    String param = "$"+s[0][0];
                    String value = s[0][1];
                    outtofile += param+" = "+value+newline;
               outtofile += newline+"#end of file"+newline;
               try
                    PropertiesDataOutput.writeBytes(outtofile);
               catch (IOException e)
                    System.out.println("ERROR while writing to Properties File: "+e);
          catch (IOException e)
               System.out.println("ERROR occured while writing to the property file for: "+ObjectPropertiesFileName);
               System.out.println("ERROR CODE: "+e);
     // sometimes before overwritting old value it's a good idea to backup old values
     public void backup()
          try
               // reference to the original properties file
               File OriginalFile = new File(ObjectPropertiesDir+ObjectPropertiesFileName);
               File BackupFile = new File(ObjectPropertiesDir+"/backup/"+ObjectPropertiesFileName+".backup");
               //opening stream to original file for read operations
               FileInputStream OriginalFileInput = new FileInputStream(OriginalFile);
               DataInputStream OriginalFileDataInput = new DataInputStream(OriginalFileInput);
               //opening stream to backup file for write operations
               FileOutputStream BackupFileOutput = new FileOutputStream(BackupFile);
               DataOutputStream BackupFileDataOutput = new DataOutputStream(BackupFileOutput);
          //     String content = "";
               String line = "";
               // do till end of file
               while ((line = OriginalFileDataInput.readLine()) != null)
                    BackupFileDataOutput.writeBytes(line+newline);
          // error handlig
          catch (IOException e)
               System.out.println("ERROR occured while back up for property file: "+ObjectPropertiesFileName);
               System.out.println("ERROR CODE: "+e);
               System.out.println("this is a serious error - the server must be stopped");
     private String cutSpaces(String s)
          while (s.startsWith(" "))
               s = s.substring(1, s.length());
          while (s.endsWith(" "))
               s = s.substring(0, s.length()-1);
          return s;
     public String createDate(String seperator)
          Date datum = new Date();
          String currentdatum = new String();
          int year, month, date;
          year = datum.getYear()+1900;
          month = datum.getMonth()+1;
          date = datum.getDate();
          currentdatum = ""+year+seperator;
          if (month < 10)
               currentdatum = currentdatum+"0"+month+seperator;
          else
               currentdatum = currentdatum+month+seperator;
          if (date < 10)
               currentdatum = currentdatum+"0"+date;
          else
               currentdatum = currentdatum+date;
          return currentdatum;
     public String createTime(String seperator)
          Date time = new Date();
          String currenttime = new String();
          int hours, minutes, seconds;
          hours = time.getHours();
          minutes = time.getMinutes();
          seconds = time.getSeconds();
          if (hours < 10)
               currenttime = currenttime+"0"+hours+seperator;
          else
               currenttime = currenttime+hours+seperator;
          if (minutes < 10)
               currenttime = currenttime+"0"+minutes+seperator;
          else
               currenttime = currenttime+minutes+seperator;
          if (seconds < 10)
               currenttime = currenttime+"0"+seconds;
          else
               currenttime = currenttime+seconds;
          return currenttime;

How to get physical memory by using system call ?

how to get physical memory by using system call ?What system call can I use.thanks

Use sysconf(3C) with SCPHYS_PAGES

How can I write a simple proxy server that intercept 80(www)socket???

Does any body knows how can i write simple proxy server that intercept web sites watching by user???thx

Does any body knows how can i write simple proxy
server that intercept web sites watching by user???thxTo be clear a proxy means that requests go to the proxy and then the proxy relays the request to proper place.
If you want to see traffic without being in the middle (the requests go direct) then you can not use the standard Java API. And do so in any situation of course requires that you be in the physical connection in the first place (ie in a star network with a router in the middle a client machine will not see packets from other machines.)

How can I write a program that compiles without warnings?

I tried the following with the 1.5 beta-compiler (build 28; I think):
class Y {
     public static final class Pair<X,Y> {
       private X fst;
       private Y snd;
       public Pair(X fst, Y snd) {this.fst=fst; this.snd=snd;}
       public X getFirst() { return fst; }
       public Y getSecond() { return snd; }
       public String toString() { return "("+fst+","+snd+")"; }
public static void main(String... args) {
     Pair[] pairArr = new Pair[10];              // supposed to be an array of Pair<Integer,Integer>
     for (int i=0; i<pairArr.length; i++)
         pairArr[i] = new Pair<Integer,Integer>(i,i);
     for (int i=0; i<pairArr.length; i++) {
         Pair<Integer,Integer> p = pairArr; // unchecked warning
     System.out.println(p);
     Integer first = p.getFirst();
     Integer second = p.getSecond();
// ... more stuff ...
It turns out that I get an unchecked warning when I extract an element from the array of pairs. Okay, that's fine. How can I avoid the warning? I had expected that an explicit cast would help.
Pair<Integer,Integer> p = (Pair<Integer,Integer> )pairArr;
With a cast I'm telling the compiler: "I _know_ what I'm doing; please trust me." But the compiler still issues a warning.
How can I write a warning-free program in this case? The only thing I can think of, is not using the parameterized type Pair in its parameterized form. But it's not the idea of Java Generics that I refrain from using parameterized types. What am I missing?

It turns out that I get an unchecked warning when I
extract an element from the array of pairs. Okay,
that's fine. How can I avoid the warning? I had
expected that an explicit cast would help.
Pair<Integer,Integer> p = (Pair<Integer,Integer>
)pairArr;
With a cast I'm telling the compiler: "I _know_ what
I'm doing; please trust me." But the compiler still
issues a warning. Yes, but at least you were able to change the warning from "unchecked assignment" to "unchecked cast" which is a little shorter ;-)
Seriously , since arrays of generic types are disallowed, there is probably no way to get rid of these warnings - which makes a strong point for eliminating "unchecked" warnings altogether (see the other thread "selectively suppressing compiler warnings")
Cheerio,
Gernot

How can I Write a sine wave in an Access-file?

I measure a sine wave in LabView 6i. How can I write the datas automatically to an Acces-file, at the same time?
In my program, I managed it with Execute SQL.vi, I change a number in a SQL statement(String) -> after this I push start and then it writes the statement in the Access-file.
The problem is, it writes only one data per measurement in the file. How can I write all datas in the Access-file and measure the wave at the same time?
Thanks for help!
Attachments:
getwave.vi ‏49 KB

On the waveform palette, you will find a "to components" vi that you can break out the array of the waveform. You can then, using a for loop write all of the values from the waveform.
Better yet, there are examples in the database toolkit manual on pages 3-13 to 3-15 that deal with reading arrays (and even has a waveform example).
Good luck!

[Urgent]How can I write to physical memory by using LabVIEW 8.2??

Similar Messages

Maybe you are looking for