Using multiple network adapters simultaneously [SOLVED]

If someone could point me in the right direction with my question that would be great - I seem to not be able to google the right types of questions on this issue.
So here it goes:
I do have a wireless adpater and and 2 ethernet cards in my machine. I would like to connect to the internet using the wireless adapter and connect to the intranet using one of the ethernet adapters. There are some local websites that are only accessible on our intranet. So the browser should ideally direct to certain IPs through eth0 and to the www through wlan0. Also CUPS should go through eth0 whereas Thunderbird should go through wlan0. At the moment I bring eth0 up when I want to print and visit the intranet and then close it afterwards again - this is somewhat inconvenient though.
I'm sure there must be a way of creating rule-sets for which protocols and IP addresses are routed through which adapter. If you can provide me with a bump in the right direction I'd appreciate it.
Last edited by itburnz (2010-03-16 08:03:31)

D'Oh! Apparently there's another post that I should've read. I assume I could use the route command to set up routes. I'll toy with that and see what happens.

Similar Messages

Round robin DNS for load balancing between multiple network adapters (Xserve)

I'm attempting to use 'round robin' DNS to load balance between the two ethernet adapters of an Xserve.
Both ethernet adapters are connected to the same LAN and have static IP addresses of 192.168.2.250 and 192.168.2.251.
The DNS zone for the server's local domain/host (macserver.private) has a machine record with both IP addresses (set up in the Lion Server UI).
Having read up on round robin DNS, I would have expected DNS requests for 'macserver.private' to be answered with the two IP addresses ordered at random, achiving my aim of requests being served at random via each ethernet adapter.
However this doesn't seem to be the case. Doing a 'nslookup' from any of the network clients results in the two IP addresses being listed in the same order everytime. And pinging 'macserver.private' only ever results in a response from the same address.
Does anyone know why this is the case? Does Lion Server use a non-standard DNS configuration? Are there any additional settings I need to configure in Lion's DNS server to make adopt a round robin approach to responding to requests?
Thanks in advance for any help!

Be careful what you wish for
Round Robin DNS is rarely the best option for 'load balancing'. At the very least it's subject to caching at various point on the network - even at the client side, once the client looks up the address it will cache that response - this means that subsequent lookups may be served from the client's cache and not refer back to the server. Therfore any given client will always see the same address until the cache expires.
I suspect this is what you're seeing.
You can minimize this by setting a lower TTL on the records. This should result in the response being cached for a shorter period, meaning the client will make more requests to the server, with a higher change of using the 'other' address.
However, you're also going to run into issues with the server having two interfaces/addresses in the same LAN. This isn't recommended.
As Jonathon mentioned, you may be better off just bonding the two interfaces. This will provide an automatic level of dynamic load balancing without the latency of DNS caches, as well as automatic failover should one link fail (as opposed to round robin DNS which will cause 50% of requests to fail until the client cache expires and a new lookup is performed (and, even then, there's still a chance the client will try to use the failed link).

Using multiple network adaptors

i have a network of macs and pc's, and i want to set it up so i have my macs able to access the net, but not the windows machines. the pc's are just fileservers which don't need access to anything other than eachother and the macs. all machines are connected to eachother by a switch, the macs also connect with their airport adaptors to an adsl router.
if i put airport at the top of the network adaptors list to prioritise it, i can't access anything over built in ethernet. if i put built in ethernet to the top, i can't access the net. i assume its because both 'work' so it doesn't move down the list to the next adaptor. i really need to get it working so the macs will try to route over both network adaptors, so whether i'm using the internet or browsing the local network, either one or the other will make it work.
i'd appreciate any advice. i am running 10.4 client and 10.4 server on the 2 macs. thanks.

re:
"Going the other way, I can connect to both 10.0.1.4 & 10.0.1.6 at the same time with the GO cmd from this wireless only machine."
yes, you're still going through the router so the wired and the wireless adapters (yes i just noticed i'd been spelling adapters wrong, oh well) are both connecting to the same thing so pinging/GOing to both ip's will work. for me my airport is connecting to a router, and my ethernet to a switch. it doesn't work because they are connecting to 2 different networks.
re:
"Hmmm, just connected the other machines Airport to an outside network and still able to get the Local network via Ethernet... the second one down."
you can connect to another wireless network yes but just getting onto another wireless network in itself isn't the problem, it depends if you can browse the other network or not, thats the trick. if you can while still connecting to the net through ethernet then thats what i need to be able to do. if you can, please let me know.

Increasing file transfer speeds with multiple network adapters?

Hello,
I want to move gigabytes of data from my PC to my PowerBook G4 at a faster rate. My PC has 802.11g WiFi and 100Mb/s ethernet and I've got my Airport's WiFi and 100Mb/s ethernet on my laptop so I'd like to somehow combine these two network interfaces to speed up my file transfers. How can I do this?
I've read a little about 802.3ad link aggregation, but AFAIK this applies exclusively to 802.3 ethernet ports.
Thanks,
Shaun
PowerBook G4 Mac OS X (10.3.9)

Does your PC have a FireWire port? you can use IP over FireWire for better throughput than the wired ethernet.
You can't use link aggregation in this case since it requires multiple interfaces of the same type (e.g. two gigabit ethernet cards), but you cannot mix media such as AirPort and Ethernet.
The alternative would be to install a gigabit ethernet card in your PC. You'd at least then get gigabit ethernet speed between the two devices which is also a step up.

How can I use multiple network connections concurrently?

I'm using a Macbook, connected to a corporate network via Ethernet and to a private ADSL connection via Airport. What I want to be able to do is use the Airport connection for specific apps (Firefox, Safari, RDP etc) and the Ethernet connection for anything that needs to access any internal resources (Exchange etc).
From what I've tried, the OS presents the primary connection (set via the Service Order configuration) to the application and nothing else. For example when Firefox is set to not use a proxy I can't access anything, unless the Airport is given priority. But when the Airport is set as the higher priority adapter via the Service Order then I can't access any of the internal network.
Is there any way to work around this or am I stuck chopping and changing whenever I need to get out to the Internet directly?

The highest priority service is the Internet connection. Anything that would go to the internet uses that service. However, you still should be able to access the internal network via Ethernet.
For example when Firefox is set to not use a proxy I can't access anything, unless the Airport is given priority.
That make sense
But when the Airport is set as the higher priority adapter via the Service Order then I can't access any of the internal network.
You should be able to at least access file servers.

Multiple network adapters and metric settings

I can't seem to get Windows to use the preferred wired adapter over the wireless. I have set a manual metric value to each adapter and it shows correctly in the route table but that doesn't seem to matter. Its still always defaulting to using
the wireless adapter. I changed the order in the advanced settings on Manage network connections as well but nether seem to work.
===========================================================================
Interface List
13... ......Bluetooth Device (Personal Area Network)
11... ......Dell Wireless 1504 802.11b/g/n (2.4GHz)
10... ......Intel(R) 82579LM Gigabit Network Connection
1...........................Software Loopback Interface 1
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.75.1 192.168.75.117 4
0.0.0.0 0.0.0.0 192.168.254.1 192.168.254.120 1011
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.75.0 255.255.255.0 On-link 192.168.75.117 258
192.168.75.117 255.255.255.255 On-link 192.168.75.117 258
192.168.75.255 255.255.255.255 On-link 192.168.75.117 258
192.168.254.0 255.255.255.0 On-link 192.168.254.120 1255
192.168.254.120 255.255.255.255 On-link 192.168.254.120 1255
192.168.254.255 255.255.255.255 On-link 192.168.254.120 1255
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.75.117 258
224.0.0.0 240.0.0.0 On-link 192.168.254.120 1255
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.75.117 258
255.255.255.255 255.255.255.255 On-link 192.168.254.120 1255
===========================================================================
Persistent Routes:
None
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
1 306 ::1/128 On-link
1 306 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
My LAN is connected to a router that makes a connection to my office. The wifi is connected to my home wifi.
So if I connected to something in the office and then turn on the wifi i get immediately disconnected and can't get back in until i turn off the wifi. I can also run nslookup and with the wifi turned on it always goes to the wifi router. I use
the wifi to access a shared storage i use with other computers in my house.
At one time this did work with this setup but last week i swapped out my drive for a larger one and re installed windows, hasn't worked since.

Hi,
As this setup did work at one time, so I think all settings you made is right, according to your description, the issue happened after you reinstall Windows, the system might lose some important updates, I suggest you check for updates, and keep all important
updates. Meanwhile, please reinstsall the network adapter driver as a test, it's recommended to look for the driver in the manufacture website.
Yolanda Zhu
TechNet Community Support

How can I use multiple overlay effects simultaneously in Photoshop?

There are 3 overlay effects available in Photoshop as layer styles: Color, Gradient and Pattern. The problem: these effects come in a strictly fixed order!
Is it possible to make a translucent Gradient Overlay over a Color Overlay using only layer styles? Or a Multiply Pattern and Color Overlays?

Another option would be Grouping the Layer, applying one Style to the Group, grouping that Group, applying the next Style to that Group, etc.

Can I use multiple sa-ns500 on the same network?

Is it possible to use multiple sa-ns500 speakers on the same network? they seem to want to have the same name on the network and therefore only 1 will connect at a time? Can I rename one somehow? Thanks!

Hello Brian,
Welcome to Sony Community.
Please check for the Secure Link option in the Home Theater System or A/V Receiver. This will help isolate the connection to the different Network speakers.
Yes, you can use multiple Network speakers on the same home network.
You can change the Device name using the Setting screen on the browser.
Follow the steps mentioned on the page # 34 and 35 of the User’s manual to start up the browser of the Network speakers and change the Device name.
If my post answers your question, please mark it as an "Accepted Solution."

Use of multiple networks in projects

Hi,
I know the standard hierarchy in Project systems like we have definition, then main WBS, then networks, then sub WBS and then activities. Now in this standard hierarchy, even though the activities are under WBS elements, the activities are connected to one network and in network graphic we can define the relationship among the various activities.
I mean by using the single network we can achieve the various objectives, then why most of the projects use multiple networks i.e. network per each WBS elements even though these multiple networks are connected to one network only.
Thanks

Hai
The criteria according to which a project is structured using a work breakdown structure and/or networks can vary and depend on the type and complexity of a project. A project can therefore also consist of a work breakdown structure and several /single networks.
For example, the criteria can vary depending on the responsibility and structure of the departments or teams involved, or on how production and assembly are integrated. It is therefore impossible to give a wholesale answer to
the question of how best to structure different types of projects.
As a rule, a project is structured according to two
points of view: structure and process.Network techniques are used for planning and controlling the process flow of projects.
ENJOY SAP
Regards
PP

ASDM multiple network objects vs group for rules

I was just curious if there are any performance benefits of using multiple network objects on multiple rules vs consolidating them into fewer rules by grouping them?
For example, I have about 10 lines of NAT exempt rules from the same source to multiple destinations. Is there anything to be gained if I consolidated those into a single rule using an object group for the multiple destinations aside from cleaning up the clutter in ASDM?
Thanks

Hello Tony,
Of course, it will be better because the processing that the ASA is going to use to determine witch rule to match would be decremented, also it would take less space on the configuration file (memory). those are some of the pros regarding creating groups for particular rules.
Sometimes a huge configuration file can increment the CPU usage,etc,etc. so it is better to keep it as small and organized as possible.
Please rate helpful posts.
Regards,
Julio

ACS 5.4 multiple network interfaces support

In ACS 5.4 release note, it says:
Multiple network interface connector support
ACS 5.4 supports up to four network interfaces: Ethernet 0, Ethernet 1, Ethernet 2, and Ethernet 3. ACS management functions use only the Ethernet 0 interface, but AAA protocols use all configured network interfaces. You must connect the ACS nodes in the distributed deployment only to the Ethernet 0 interface. Therefore, the syslog messages are sent and received at the log collector's Ethernet 0 interface. Data forwarding from one interface to another interface is prohibited to prevent potential security issues. The external identity stores are supported only on the Ethernet 0 interface. In ACS 5.4, multiple network interface connectors are also supported for proxies.
But in the CSACS 1121 Series Appliance Rear View section, it still says on Ethernet 0 is usable. All other interfaces are blocked.
I am confused. Can anyone clarify for me if we can use multiple network interface in ACS 5.4? What about management interface?
Thanks!

We configured 2 interfaces in past within testing enviornment and it worked. ACS 5.4 supports multiple network interfaces on the UCS platform, on a virtual machine and on the legacy ACS 5.x IBM/CAM hardware. The ACS management functions use the interface eth0 only and the AAA protocols use all available network interfaces.
Jatin Katyal
- Do rate helpful posts -

How can I use PowerShell to Remove "Ghost" (Old Hidden) VMware Network Adapters in Windows 7?

We recently upgrade the virtual hardware of some of our VMware VM's running Windows 7. One side-effect is that in Windows on these machines, an instance of the NIC from the previous version of virtual hardware remains, as a hidden
device. This can be easily found manually on a machine by enabling Device manager to show hidden devices (registry and a menu option - View...Show Hidden Devices). You can then just right-click on the device in question and uninstall.
The problem here, like in so many other tasks, is that you may have multiple instances, on multiple machines. We had just that, and in scouring the internet for a PowerShell only script to resolve the issue, I could not find one. Therefore, I've written
my own.
This exact script is only seeking out VMware "VMXNET3" nic cards, but could be easily adapted to find Ghost NIC's for a different vendor using my example. There are also some commented lines left in to aid you as an example of how you can
test the various queries in your own environment, on a test machine, before a full-blown deployment.
NOTE: Please try this out (at your own risk - I am not responsible for how this works out for you), and please vote for my answer to this dilemma if this helped you. I'd appreciate it after all of the sweat the script took to crank out.
Thanks!
P.S. This script, of course, requires that Powershell is installed and enabled on the target computer. It then must be run as System - In our environment it is being remotely pushed through a software delivery systems, which runs this scrpt
as system.
THE SCRIPT:
CLS
#Querying WMI for Ghost NICs and Returning Criteria...
Write-Host "VMware Ghost NIC Remover" -Foreground GREEN
Write-Host "Author: Octavio Serpa AKA Octavio-Admin"
Write-Host "Copyright Octavio Serpa - Octavio-Admin - 2014"
Write-Host ""
Write-Host "Checking Powershell Version" -Foreground Yellow
$host.version
Write-Host ""
Write-Host "Searching for Ghost NIC's" -Foreground Yellow
$Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "vm*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
If ($Ghosts -NE $NULL)
  Write-Host "One or more ghost NIC'S do exist on this machine. Script will continue..." -foreground RED
  Write-Host ""
  else
  Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
  Write-Host ""
  EXIT 0
#Using Criteria to Obtain the GUID of each Ghost NIC
Write-Host "Getting NIC Variables" -Foreground Yellow
foreach ($_ in $Ghosts) {
  $DID = $_.DeviceID
  If ($DID -NE $NULL)
  Write-Host "The NIC DID: $DID"
  else
  Write-Host "$DID is NULL - Exiting..."
  EXIT 666
  if($DID -NOTLIKE "1*")
   Write-Host "Adding additional 0 to registry lookup since the DID is just one character..." - foreground yellow
   Write-Host ""
   $NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\000$DID"
  ELSE
   $NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00$DID"
  $GUID = $NICREG.NetCfgInstanceId
  Write-Host "The NIC GUID: $GUID"
                $PNPDID = $NICREG.DeviceInstanceID
  $PNPDID = $PNPDID.Trimstart("PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\")
  Write-Host "The truncated PNPDevice ID is $PNPDID"
  Write-Host ""
  Write-Host "Searching for Registry Keys that match NIC GUID: $GUID" -Foreground Yellow
  $NICREGPATH = @(1..50)
  foreach ($_ in $NICREGPATH)
   $TESTREG = Test-Path "HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_" -Verbose
   if($TESTREG -EQ $FALSE)
    #Write-Host ""
    #Write-Host "FALSE: HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_ DOES NOT EXIST" -Foreground RED
    ELSE
    #Write-Host "True - NIC $_ Exists" -Foreground Green
    $NICID = $_
    $SubPath1 = 'HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
    #Write-Host "The Sub-Key Path To Query = $SubPath1"
    $SubPath2 = 'HKLM:\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
    #Write-Host "The Sub-Key Path To Query = $SubPath2"
    $NICProperties = Get-ItemProperty $SubPath1
    #$NICProperties
    $Match = $NICProperties.ServiceName
    #$Match
    foreach ($_ in $Match) {
    #Write-Host "The NIC GUID found in this registry key is: $_" -Foreground Yellow
    #Write-Host ""
    if($_ -NE $GUID)
    #Write-Host "NO MATCH - THIS NIC HAS NOT BEEN TOUCHED" -Foreground GREEN
                               #Write-Host ""
    ELSE
    Write-Host "MATCH - Registry Entries for this NIC will be DELETED" -Foreground RED
    Remove-Item $SubPath1 -Recurse -ErrorAction SilentlyContinue
    Remove-Item $SubPath2 -Recurse -ErrorAction SilentlyContinue
    $CCS = @("ControlSet001", "ControlSet002")
    foreach ($_ in $CCS) {
     $CCS = $_
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\Tcpip\Parameters\Adapters\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\DeviceClasses\{ad498944-762f-11d0-8dcb-00c04fc3358c}\##?#PCI#VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01#$PNPDID#{ad498944-762f-11d0-8dcb-00c04fc3358c}\#'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Network\{4D36E972-E325-11CE-BFC1-08002BE10318}\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\JNPRNA\Parameters\Adapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\NetBT\Parameters\Interfaces\Tcpip_' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Psched\Parameters\NdisAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Adapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\DNSRegisteredAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Interfaces\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\WfpLwf\Parameters\NdisAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
                                         if($DID -NOTLIKE
"1*")
              $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\000' + $DID
                         Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
       ELSE
       $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00' + $DID
       Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Enum\PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\' + $PNPDID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
#This is our Success check at the end
Write-Host ""
Write-Host "Searching for any remaining Ghost NICs:" -Foreground Yellow
          $Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "vm*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
  If ($Ghosts -NE $NULL)
  Write-Host "There is still at least one ghost NIC present. The remover script may not be functioning correctly. Please contact Octavio-Admin on Microsoft Technet Forums with any questions" -foreground RED
  Write-Host ""
  EXIT 666
  else
  Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
  Write-Host ""
  EXIT 0

THE SCRIPT:
CLS
#Querying WMI for Ghost NICs and Returning Criteria...
Write-Host "VMware Ghost NIC Remover" -Foreground GREEN
Write-Host "Author: Octavio Serpa AKA Octavio-Admin"
Write-Host "Copyright Octavio Serpa - Octavio-Admin - 2014"
Write-Host ""
Write-Host "Checking Powershell Version" -Foreground Yellow
$host.version
Write-Host ""
Write-Host "Searching for Ghost NIC's" -Foreground Yellow
$Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "vm*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
If ($Ghosts -NE $NULL)
Write-Host "One or more ghost NIC'S do exist on this machine. Script will continue..." -foreground RED
Write-Host ""
else
Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
Write-Host ""
EXIT 0
#Using Criteria to Obtain the GUID of each Ghost NIC
Write-Host "Getting NIC Variables" -Foreground Yellow
foreach ($_ in $Ghosts) {
$DID = $_.DeviceID
If ($DID -NE $NULL)
Write-Host "The NIC DID: $DID"
else
Write-Host "$DID is NULL - Exiting..."
EXIT 666
if($DID -NOTLIKE "1*")
   Write-Host "Adding additional 0 to registry lookup since the DID is just one character..." - foreground yellow
   Write-Host ""
   $NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\000$DID"
ELSE
   $NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00$DID"
$GUID = $NICREG.NetCfgInstanceId
Write-Host "The NIC GUID: $GUID"
                $PNPDID = $NICREG.DeviceInstanceID
$PNPDID = $PNPDID.Trimstart("PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\")
Write-Host "The truncated PNPDevice ID is $PNPDID"
Write-Host ""
Write-Host "Searching for Registry Keys that match NIC GUID: $GUID" -Foreground Yellow
$NICREGPATH = @(1..50)
foreach ($_ in $NICREGPATH)
   $TESTREG = Test-Path "HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_" -Verbose
   if($TESTREG -EQ $FALSE)
    #Write-Host ""
    #Write-Host "FALSE: HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_ DOES NOT EXIST" -Foreground RED
    ELSE
    #Write-Host "True - NIC $_ Exists" -Foreground Green
    $NICID = $_
    $SubPath1 = 'HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
    #Write-Host "The Sub-Key Path To Query = $SubPath1"
    $SubPath2 = 'HKLM:\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
    #Write-Host "The Sub-Key Path To Query = $SubPath2"
    $NICProperties = Get-ItemProperty $SubPath1
    #$NICProperties
    $Match = $NICProperties.ServiceName
    #$Match
    foreach ($_ in $Match) {
    #Write-Host "The NIC GUID found in this registry key is: $_" -Foreground Yellow
    #Write-Host ""
    if($_ -NE $GUID)
    #Write-Host "NO MATCH - THIS NIC HAS NOT BEEN TOUCHED" -Foreground GREEN
                                #Write-Host ""
    ELSE
    Write-Host "MATCH - Registry Entries for this NIC will be DELETED" -Foreground RED
    Remove-Item $SubPath1 -Recurse -ErrorAction SilentlyContinue
    Remove-Item $SubPath2 -Recurse -ErrorAction SilentlyContinue
    $CCS = @("ControlSet001", "ControlSet002")
    foreach ($_ in $CCS) {
     $CCS = $_
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\Tcpip\Parameters\Adapters\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\DeviceClasses\{ad498944-762f-11d0-8dcb-00c04fc3358c}\##?#PCI#VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01#$PNPDID#{ad498944-762f-11d0-8dcb-00c04fc3358c}\#'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Network\{4D36E972-E325-11CE-BFC1-08002BE10318}\'+$GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\JNPRNA\Parameters\Adapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\NetBT\Parameters\Interfaces\Tcpip_' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Psched\Parameters\NdisAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Adapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\DNSRegisteredAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Interfaces\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\WfpLwf\Parameters\NdisAdapters\' + $GUID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
                                         if($DID -NOTLIKE
"1*")
              $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\000' + $DID
                         Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
       ELSE
       $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00' + $DID
       Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
     $reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Enum\PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\' + $PNPDID
     Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
#This is our Success check at the end
Write-Host ""
Write-Host "Searching for any remaining Ghost NICs:" -Foreground Yellow
          $Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "vm*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
If ($Ghosts -NE $NULL)
Write-Host "There is still at least one ghost NIC present. The remover script may not be functioning correctly. Please contact Octavio-Admin on Microsoft Technet Forums with any questions" -foreground RED
Write-Host ""
EXIT 666
else
Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
Write-Host ""
EXIT 0
Hello Octavio,
I'm having similar issues with azure VMs (windows server 2008 and 2012). I noticed that the name of the network adapter changes every time the servers are turned off and then on.
For example every time I perform that action on each VM, the network adapter became to "Microsoft Hyper-V Network Adapter #3" (and then #4, #5, etc).
I found in to many forums that to resolve that is needed to remove Hidden (Ghost) Network Adapters and most of the people is doing that manually from the device manager (right click on the hidden network adapter and select uninstall).
Then I found this script created by you and made some changes to find Description -like "Microsoft Hyper-V Network*".
It seems to find the adapters and also remove them (based on the script results). But if I go to the device manager after restarting the server, all hidden (ghost) adapters are still there (for example Microsoft Hyper-V Network Adapter
#2, Microsoft Hyper-V Network Adapter #3, Microsoft Hyper-V Network Adapter #4, Microsoft Hyper-V Network Adapter #n).
The only thing I noticed after running the script is that, in the Control Panel -> Network and Sharing Center, the name of the adapter has no # (Now is shown as “Ethernet” and before as “Ethernet #”)
This is my script, could you please take a look and tell me if there is something wrong o missing?
CLS
#Querying WMI for Ghost NICs and Returning Criteria...
Write-Host "VMware Ghost NIC Remover" -Foreground GREEN
Write-Host "Author: Octavio Serpa AKA Octavio-Admin"
Write-Host "Copyright Octavio Serpa - Octavio-Admin - 2014"
Write-Host ""
Write-Host "Checking Powershell Version" -Foreground Yellow
$host.version
Write-Host ""
Write-Host "Searching for Ghost NIC's" -Foreground Yellow
$Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "Microsoft Hyper-V Network*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
If ($Ghosts -NE $NULL)
Write-Host "One or more ghost NIC'S do exist on this machine. Script will continue..." -foreground RED
Write-Host ""
else
Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
Write-Host ""
EXIT 0
#Using Criteria to Obtain the GUID of each Ghost NIC
Write-Host "Getting NIC Variables" -Foreground Yellow
foreach ($_ in $Ghosts) {
$DID = $_.DeviceID
If ($DID -NE $NULL)
Write-Host "The NIC DID: $DID"
else
Write-Host "$DID is NULL - Exiting..."
EXIT 666
if($DID -NOTLIKE "1*")
Write-Host "Adding additional 0 to registry lookup since the DID is just one character..." - foreground yellow
Write-Host ""
$NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4d36e972-e325-11ce-bfc1-08002be10318}\000$DID"
ELSE
$NICREG = Get-ItemProperty "hklm:\SYSTEM\CurrentControlSet\Control\Class\{4d36e972-e325-11ce-bfc1-08002be10318}\00$DID"
$GUID = $NICREG.NetCfgInstanceId
Write-Host "The NIC GUID: $GUID"
$PNPDID = $NICREG.DeviceInstanceID
$PNPDID = $PNPDID.Trimstart("PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\")
Write-Host "The truncated PNPDevice ID is $PNPDID"
Write-Host ""
Write-Host "Searching for Registry Keys that match NIC GUID: $GUID" -Foreground Yellow
$NICREGPATH = @(1..50)
foreach ($_ in $NICREGPATH)
$TESTREG = Test-Path "HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_" -Verbose
if($TESTREG -EQ $FALSE)
#Write-Host ""
#Write-Host "FALSE: HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\$_ DOES NOT EXIST" -Foreground RED
ELSE
#Write-Host "True - NIC $_ Exists" -Foreground Green
$NICID = $_
$SubPath1 = 'HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
#Write-Host "The Sub-Key Path To Query = $SubPath1"
$SubPath2 = 'HKLM:\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\NetworkCards\'+$NICID
#Write-Host "The Sub-Key Path To Query = $SubPath2"
$NICProperties = Get-ItemProperty $SubPath1
#$NICProperties
$Match = $NICProperties.ServiceName
#$Match
foreach ($_ in $Match) {
#Write-Host "The NIC GUID found in this registry key is: $_" -Foreground Yellow
#Write-Host ""
if($_ -NE $GUID)
#Write-Host "NO MATCH - THIS NIC HAS NOT BEEN TOUCHED" -Foreground GREEN
#Write-Host ""
ELSE
Write-Host "MATCH - Registry Entries for this NIC will be DELETED" -Foreground RED
Remove-Item $SubPath1 -Recurse -ErrorAction SilentlyContinue
Remove-Item $SubPath2 -Recurse -ErrorAction SilentlyContinue
$CCS = @("ControlSet001", "ControlSet002")
foreach ($_ in $CCS) {
$CCS = $_
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\'+$GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Services\Tcpip\Parameters\Adapters\'+$GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\DeviceClasses\{ad498944-762f-11d0-8dcb-00c04fc3358c}\##?#PCI#VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01#$PNPDID#{ad498944-762f-11d0-8dcb-00c04fc3358c}\#'+$GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Network\{4D36E972-E325-11CE-BFC1-08002BE10318}\'+$GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\JNPRNA\Parameters\Adapters\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\NetBT\Parameters\Interfaces\Tcpip_' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Psched\Parameters\NdisAdapters\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Adapters\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\DNSRegisteredAdapters\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\Tcpip\Parameters\Interfaces\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\services\WfpLwf\Parameters\NdisAdapters\' + $GUID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
if($DID -NOTLIKE "1*")
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\000' + $DID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
ELSE
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00' + $DID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
$reg1 = 'HKLM:\SYSTEM\' + $CCS + '\Enum\PCI\VEN_15AD&DEV_07B0&SUBSYS_07B015AD&REV_01\' + $PNPDID
Remove-Item $reg1 -Recurse -ErrorAction SilentlyContinue -verbose
#This is our Success check at the end
Write-Host ""
Write-Host "Searching for any remaining Ghost NICs:" -Foreground Yellow
$Ghosts = gwmi win32_NetworkAdapter | ?{$_.Description -like "Microsoft Hyper-V Network*" -and $_.Installed -like "True" -and $_.MACAddress -eq $null}
$Ghosts | Select-Object Name,DeviceID
If ($Ghosts -NE $NULL)
Write-Host "There is still at least one ghost NIC present. The remover script may not be functioning correctly. Please contact Octavio-Admin on Microsoft Technet Forums with any questions" -foreground RED
Write-Host ""
EXIT 666
else
Write-Host "No ghost NIC's Found :) - Exiting..." -Foreground Green
Write-Host ""
EXIT 0

New 13" Macbook Pro trying to connect to a Panasonic VIERA TC-L42U30 as second monitor. I've used multiple hdmi-thunderbolt/mini displayport adapters and multiple hdmi cables and still no success. The Macbook does not sense the second monitor (TV). Help?!

I've been a Mac since 2008, so I know my way around the system pretty well. This issue, however, has me stumped. I had an iMac until now and only now am I experiencing some difficulty with my new MacBook Pro. The model I have is the newest 13" Macbook Pro model and I'm trying to connect a Panasonic VIERA TC-L42U30 42" HDTV as a second monitor via the Thunderbolt port.
It worked the first two times and hasn't worked since, after 10-15 attempts with different configurations, turning things on n off, restarting the mac, unplugging the cables, adapters, TV, resetting the P RAM, etc... I've used multiple hdmi-thunderbolt/mini displayport adapters and multiple hdmi cables and still no success. No matter what I do, the Macbook does not sense the TV as a second monitor anymore.
I took the MacBook Pro to the Apple Store, and their "genius" there had it working fine with a DVI connection to a regular monitor. The Panasonic TV I have has HDMI connections and one VGA connection which does not support HD, but no DVI option. I want an HD connection to mirror or extend my MacBook Pro screen. At the Apple Store, they didn't have a Thunderbolt/Mini DisplayPort to HDMI adapter, so he could not try that out for me.
Anyone else have this configuration or another similar one with a Panasonic HDTV?
Ideas? Suggestions? Anything?! Help!!
P.S. I'm running Mountain Lion, if that wasn't already obvious. Everything is up to date in my App Store as well.
Thanks!

Hi There,
I have had the exact same issue but with a projector.
The issue lies with Mountian Lion 10.8.2.
I tried many a combination with no luck to get HDMI working.
Took my mac into the apple store and came to the conclusion it was the software, so I asked them to install 10.8 onto it (this is destructive so a backup is a must)
Bought my macbook home and voila, now displaying through my projector.
There is a small graphics update after 10.8.1 which seems to be the cause.
Hope this helps.
Thanks.

Can I use my Time Capsule to set up multiple networks, or just one?

Can I use my Time Capsule to set up multiple networks, or just one? We'd like to offer the internet to clients who are at our studio, but don't want them able to access all our computers, so a second network for them would be useful.

Two big IFs here.
Not all versions of the Time Capsule have Guest Networking capability, so it might be a good idea to verify that first. Can you provide the model number of your Time Capsule. it's on the bottom of the device.....starts with an "A" followed by four numbers.
Next, assuming that the Time Capsule has Guest Network capability, the next requirement would be to verify that your modem is compatible with the Time Capsule for that feature.
Basically, you need a simple modem.....not a modem/router or gateway device that is often furnished by Internet Service Providers. If you are not sure what you have, post back with the make and model number of your "modem" and we'll see if we can find some details ont he device.

Multiple networks using single network adapter

Hi,
If I have only single network adapter in a OVM server (or single bond interface bond0 created from two network adapters), is it possible to separate networks for
VM management, live migrate and VM public networks using any mechanism, say by creating VLANs? I am having two 10G adapters in each of the VM server
and would like to separate traffic of each of these networks. Thanks in advance.

Hi,
10G adapter is the best NIC performance so with two NICs like this, i recommand you to use the bond0 (mode 1) for fault tolerance and use the VLAN technology to separate the Networks.
Note that Oracle VM support the VLAN configuration.
I hope this can help you
Best Regards

Using multiple network adapters simultaneously [SOLVED]

Similar Messages

Maybe you are looking for