V880 with memory errors

I have a v880 that is getting many corrected memory errors. Should I be concerned about this? Should I get the memory replaced? What are my options?

As this is a V880, I would hope that the server is still under a support contract with Sun, in which case yes it would be a good idea to open a support case with them. Even if the dimms do not need replaced they can log the events for you which helps your support on this server in the future, should you get further issues.
But, back to business. What I would do is to pass the server through maximum diagnostics a few times and check the outputs for reported dimm errors.
Other than that you might like to give us a little bit more information, such as the following:
1. The errors from the /var/adm/messages file
2. The output from prtdiag -v
3. An indication of if the server is crashing with these errors and if so if any crash dumps are being created.

Similar Messages

Remote Control crashes randomly with memory error

During authentication, but most usually during disconnection Remote Control (using Consoleone) will crash with the following error:
RCConsole.exe - Application Error
The instruction at "0x10002834" referenced memory at "0x0000000c". The memory could not be "read".
Click on OK to terminate the program
Click on CANCEL to debug the program
OK Cancel
I tries searching Google and a few other engines with no luck, has anyone seen this before?

The only time that I've seen the error that's listed below is from running ConsoleOne from a UNC path. Try copying all files and folders from \\servername\SYS\PUBLIC\mgmt\ConsoleOne\1.2 to c:\1.2, and then try running c:\1.2\bin\consoleone.exe. Doing so has fixed this error for me in the past
Tim
Originally Posted by bsecrist
During authentication, but most usually during disconnection Remote Control (using Consoleone) will crash with the following error:
RCConsole.exe - Application Error
The instruction at "0x10002834" referenced memory at "0x0000000c". The memory could not be "read".
Click on OK to terminate the program
Click on CANCEL to debug the program
OK Cancel
I tries searching Google and a few other engines with no luck, has anyone seen this before?

P35 Platinum sits at post with Memory error.

Brand new rig, I put it all together, and on post it starts, does its reset after 3 seconds, (all LEDs red before it does the restart, in case thats wrong)
Then tries again, stopping at r-r-g-r, which the manual says is mem error.
I have tried only putting one stick in, and checked all the slots, i also tried the other stick.
No difference whatsoever. I have no video at all at any time, nothing has ever shown.
At the moment i have no other ram to check my ram against, So is there anything else it could be? The PSU seems to work flawlessly as
it's led system is showing correctly. And its not like theres any drain on it. I have reseated the cpu/hs and gfx twice now. No difference.
Any help would be appreciated, life really sucks without a good computer.
q6600
2xWD500gig Sata (tried booting with neither hooked in at all)
random DVD drive, unhooked to eliminate chance of it being the cause, it Isn't.
OCZ ddr2 pc2 8500 1066 reaper, 2x1gig
msi p35 plat rev1.1, no idea what the bios is.
Enermax infinity 720
EVGA 8800gts 320

Don't Reaper's need about 2.2~2.3v?
If so, there's your answer, board doesn't do 1.8-1.9v+ out the box.
Get some 667/800 1.8v RAM.

Memory Error in Bridge while running a script with multiple moveTo()'s.

I have written a script to create folders based on the names of assets in the parent folder, then move the assets with matching names into the appropriate folders. The script runs perfectly up to somewhere between 1,000 to 1,500 images moved and then I receive a memory error from Bridge.
I have been running this on folders with an excess of 25,000 assets in them. My work around was to put a simple counter in the script to let me know when 1,000 assets had been moved, throw up an alert, and then I would view the Task Manager to let me know when the CPU usage had dropped below 50% and would ok the alert, then it would run the next 1000 assets.
My question, is it possible in scripting to monitor your memory usage to allow a pause in the script so Bridge processing can catch up?

Don't do that!
$.sleep() doesn't "sleep". ExtendScript is not multi-threaded. $.sleep just waits on the $.sleep() command to execute. It actually blocks all processing rather than free up the processor to do things like garbage collection.
First try the $.gc() command. To my knowledge there is no way to track ES' memory usage.
If that doesn't work, try scheduling a task...
Let's say that you find that after 1000 moves, it takes 60 seconds for the processor to cool off:
doAThousandMoves = function() {
// execute 1000 moves
app.scheduleTask( "doAThousandMoves()", 60000, true );
The way I would actually code this is to scan the folder tree and create a global array that contained all of the files to be moved.
I would then move them 1 at a time, shifting them off the array. Something like this:
var mover = {}; // global object declaration
mover.init = function() {
mover.files = new Array();
// fill mover files with the file objects to be moved.
app.scheduleTask( "mover.move()", 10 );
mover.move = function() {
var i = 0;
while ( i++ < 1000 ) {
file = mover.files.shift();
// move file
if ( mover.files.length > 0 ) {
app.scheduleTask( "mover.move()", 60000 );
In fact, you should probably break this into chunks of about 10 or so at a time (you can reduce the gap between calls). Doing so will make the operation appear to be running as a background process.
Regards
Bob

My MacBook Pro version 10.7.5 4GB (keeps crashing with the error message 'Your MAC OSX start up disk has no more space available for application memory' - what do i do

My MacBook Pro (version 10.7.5 4GB)keeps crashing with the error message 'Your MAC OSX start up disk has no more space available for application memory' - what do i do. I keep force quitting the applications and turning the computer off but it happens again after a while

Hhow much goal and free hard disk space is available? Sounds like you need to move some things off of that hard drive.

Partition Failed Partition failed with the error: POSIX reports: The operation couldn't be completed. CAN NOT ALLOCATE MEMORY

I plug usb mass storage device to my macbook pro i7 than every thing is stack and i reinforce to shutdown and than I start again but mac fail to boot again.
I tried different optiones in disk utility in mac os startup disk. but still fail to repair, erase and partition. I try to fix with the steps listed in
https://discussions.apple.com/message/13288923#13288923
but it fail to partition with the msg:
Partition Failed
Partition failed with the error: POSIX reports: The operation couldn’t be completed.cannot allocate memory
pls pls pls help urgentely on this matter I stop working.
Kind Regards,
pe

Hi again OGELTHORPE.
I've already run two hardware tests. One quick one and one extended one. It was unable to pick anything up.
It's like everything is running perfectly, but when I go to erase the HDD or partition it, it pops up with the error message. Even when I try to erase and partition using "Terminal", I received the same error message.
It's beginning to do my head in, but will see if replacing the SATA cable will make any difference. If it doesn't, I'll hazard a guess it could be the Logic Board.
Thanks again for your suggestions!
L.

Memory Errors with NX4 and Adobe 3D

After installing the Adobe 3d trial version,I've had nothing but problems with NX4.Out of memory errors when there is plenty available.REinstalled NX4,same problems.Uninstalled adobe 3D,and the problem went away.We would like to purchase this,but not until this particular problem is solved.
Win Xp SP2
2 GB Ram
Dell Precision 370
Pentium 4
NX 4.0.0.25

are you working on big 3d models in nx4 ?(to check that, please do a right click on the windows task bar and open the task manager and check the memory used by nx4 with your 3d models loaded)- did the problem also occured with small models ?
if you memory footprint approaches the 2gb barrier, then 3d capture might be the cause ot your memory problems, to get rid of it, just open acrobat3d and go in the menu edit/preferences/3d capture and delete nx4 from your list of capturable applications.

HELP! Games quit with memory writing errors

Hello
I have Barton 2500+ Unlocked; I run it on 11x200, the system run stable on general
But when I play games, the games quit with memory writing errors, I have good Kingston RAM, and it should run on 200 FSB without any problem, I saw many people run them 2500+ at 11x200 without any problem, it could be my DRAM settings, or my VCore, Or What?
I tried many thing on DRAM BIOS options, But nothing of them last for more than 10 Min on game..
Any suggestions??
CPU TEMP: 59C
SYS TEMP: 45C
VCORE: 1.75
MEMORY V: 2.7
PS: In Core Center on it Left panel show the FSB as 208, But on the main screen show it as 200x11

CPU-Z version 1.21
Memory Modules Serial Presence Detect (SPD)
Module #1
General
Memory type      DDR-SDRAM
Manufacturer (ID)    Kingston (7F98000000000000)
Size         512 MBytes
Max bandwidth      PC3200 (200 MHz)
Part number      K
Attributes
Number of banks   2
Data width      64 bits
Correction      None
Registered      no
Buffered      no
Timings table
Frequency (MHz)      166   200
CAS#         2.0   2.5
RAS# to CAS# delay    3     3
RAS# Precharge      3   3
TRAS#         7   8

Out of memory Error with jdk 1.6

Hello,
I have a swing application launched on the client with the help of Java web start. The applications works fine in jre 1.4 and jre 1.5. The heap sizes are :
initial-heap-size="5m" max-heap-size="24m"
But when I run this using jre 1.6.0_05-b13, I am getting Out of memory Error, java heap size. And I see the memory usage is growing rapidly which I didn't notice in other jre versions (1.4 and 1.5).
Does anyone have any idea on this?
Thanks in advance,
MR.

Thanks for your response Peter. During my continuous testing I identified that error happens on jdk 1.5 also. And I have increased the min-heap-size to 24 MB and max-heap-size to 64 MB. But in that case also I noticed the out of memory error. The interesting thing is, the min-heap-size is never increased from 24MB and lot of free memory also.
Memory: 24,448K Free: 12,714K (52%) ... completed.
The Outofmemoryerror triggers from the reader thread which does the job of reading the data from the InputStream. One thing is we are continuously pushing more data on the output stream from the other end. Is that any limitation on InputStream which can hold some definite amount of data.
Please throw some light on this.

Encountering with the error Client out of memory in Bex. . .

Hello All,
In the Bex report when I run for the 2000 sales organization selection the initial display is coming fine. When I try to drill down to the next levels in the result, I am encountering with the error 'CLENT OUT OF MEMORY'.
The report is displaying sales document level data. I need to drill down on almost 6 fields like cost element, Profit center. Auth group, Cost center, Customer number... Up to 7 attributes.
I am able to drill down up to 5 attributes when i try to drill down on the 6th one, the report ended up with this error.
Note: I am able to run the report for remaining sales orgs and can drill down on all the fields. Might be because of huge data not able drill down on 2000, not sure
Any one could help me on this.
Thanks in Advance,
Lakshmi.

I checked in the infoprovider level.
For the same selection, we have around 450000 of cells.
Thank you,
Lakshmi.

There is not enough memory error with 8gb installed

Description:
I'm getting an error when trying to copy or cut a collection of basic shapes in CS6 on Mac OS X 10.8.
It reads:
There is not enough memory to complete the operation.
To increase available memory, close other open documents or applications.
But when i check activity monitor there is plenty of memory available. I can succesfully copy a smal(ler) amount of shapes.
Steps already taken:
Tried copying after a system restart with no other programs running.
Tried adding more memory (i had 4gb originally, I just upgraded to 8gb).
I reinstalled Flash
I tried the same procedure (copying the same amount of shapes) on another machine with a similar amount of RAM and this works fine.
Is there a way you can allocate more memory to flash, or is this some setting that i'm missing?
Any help would be greatly appreciated!
P.s. I read this thread http://forums.adobe.com/message/3609214#3609214, and my problem is only different in that i don't have some huge files i'm dealing with. The .fla is only ~10mb.

Thanks for chiming in Mataxia.
One thing you can try is selecting the layers that have the shapes you want to copy. Then right click and choose copy layers. In my case this works even though selecting just the shapes (instead of the layers) will cause the memory error.
I'm using this as a workaround, but i can imagine that this isn't of any help in all cases.
This confirms my suspicions that this is a bug in flash. Would be great if someone from Adobe were reading this...

Error with ini files & Memory Error

Hi All,
I am attaching my VI which is used to save the control values, I am doing it with configuration file, but sometimes what happens my configuration file got erased completely,and my data got lost otherwise saving control values works perfectly fine, how can I stop this so my configuration data is safe. or is there any other method to save the control values.
2ndly, I have another error in a different vi which keeps coming (image is attached as "Memory Error"), I tried installing LV and XP again, changed the PC but problem persists.
Could someone please try to throw some light on these issues.
Thanks & Regards
James
Attachments:
ini error.PNG ‏24 KB
Save control values.vi ‏50 KB
Error2.JPG ‏1 KB

Your Error2 image is not viewable. Looks like a corrupt upload.
Your fundamental problem lies in the first part of your code. If the INI file doesn't exist, then when you open it, a new one gets created. There is no SVALUE key, so you are trying to loop 0 times. Since the first for-loop does not execute, the INI file refnum does not get transferred through the tunnel, and subsequent INI file functions receive a null refnum. You need to either wire the refnum outside the loops or use shift registers for the refnum.
As to your code: OK...
You must really like whitespace, because that's the only reason I can see for having such a huge while loop that just sits there.
You really need to learn to draw straight wires.
You are jumping through unnecessary hoops. You are taking the control values, bundling them into a cluster, converting the cluster into an array, and then autoindexing the array while at the same time setting the "N" terminal of the for-loop. Whew!
Skip the bundling. Just make an array directly!
Do not wire both the "N" terminal of a for-loop and autoindex. Do one or the other. Since you have the array, just auto-index.
The Index Array function is resizable. You do not need to place 2 of them to get the 2 values.
Your string constants are in 2 places. You should have them in one place only. If you decide to change the names then you need to remember to change them in 2 places.

Can anyone help with an out of memory error on CS2?

Hello,
I have been battling with an out of memory error on a dell laptop running 2gb of ram. I have had no prior issues with this laptop running CS2 until last week when I started getting the out of memory errors. I have seen several articles about this occuring on later versions of illustrator. Just prior to this issue appearing I had to delete and rebuild the main user profile on the computer due to it consistently logging into a temporary account.
Once the new profile was established and all user documents and profile settings were transferred back into it, this problem started showing up. The error occurs when clicking on files listed as Illustrator files, and when opening the illustrator suite. Once I click on the out of memory error it still continues to load illustrator. The files are located on a server and not on the remote computer. I have tried to copy the files to the local hard drive with the same result when I try to open them. I also tried to change the extension to .pdf and got no further. I tried to open a file and recreate the work and all I got was the black outline of the fonts. none of the other artwork appeared. once rebuilt, when trying to save, It gives the out of memory error and does not save the file.
Illustrator was installed on another dell laptop, same model, etc and works fine. no problem accessing network files. I just attempted to use Illustrator from the admin profile on the machine in question and it works fine and lightening fast. Just not from the new rebuilt profile. I have tried to uninstall and reinstall the software. it has not helped. could there be stray configuration settings that we transfered over to the new profile that should not have been?
Any insights will be helpful.
Thank You,
Brad Yeutter

Here are some steps that could help you:
http://kb2.adobe.com/cps/320/320782.html
http://kb2.adobe.com/cps/401/kb401053.html
I hope this helps!

Job in BODS is failing with an error " Your system is running low on process virtual memory".

hello,
I am facing an error with one of my job which is running on BODS server. The job is failing daily since last one year with the same error " Your system is running low on process virtual memory". We checked with team which deals with space issue and the space is sufficient enough.
Please help me with this error and what can be done to do away with this.
Regards,
Ritu Sharma

Greetings Narendra,
It may help if you were to explain in more detail the software product you are encountering this issue. There are about 500 different products that might be encountering this issue. Specifying which product you are using will assist the Forum Team in providing an appropriate response.
Thank you,
Rob
Technical Engineer
Customer Assurance

Out of memory error with 80Kb file?

Hi, my pc has 2Gb of Ram, a page file that is setup correctly
and the physical ram is almost non-used (500Mb)
When I start DW and load a php file of 80Kb approx., it just
hangs/locks up. When I wait for it, it gives me an "out of memory"
error, and when you look in windows task manager, it just keeps
hogging up ram.
My laptop is a "simple", 1Gb Hp pavillion, and when I open
the file there, it just works like it's supposed to, using about
70Mb of ram, instead of the gigabyte(s) it does on my developer
machine....
Adjusting virtual memory has absolutely no effect.. It seems,
after some reading, that people using 2gb of ram, have the most
problems in this area?
Adobe, please help here !
EDIT: i just tested another file, 136Kb large, that loads
normal!, so it has to do with the files in specific... If you want
to test the files, just download "Simplemachines Forum" and load
the "load.php" or the "post.php" files from the source directory,
to trigger the lockup...

mmm... just tried using a "workaround" if you still can call
it that
Installed a virtual machine (xp) with less than 2gigs, and it
works... I really hope someone else has got these kind of errors
yet.... 2500$ + software, wich I can't use for now... Using
notepad2 for time being...

V880 with memory errors

Similar Messages

Maybe you are looking for