VBAI GigE and Modbus must use common NIC?

Hi,
I cannot find any way to use separate NIC for GigE and Modbus TCP/IP in VBAI. VBAI insists on using wich ever adapter the GigE camera is using.
Any one that can help me?

EDIT: Here is what I see. Note that this is what I see from the computer running my Modbus Master server. The computer that is running VBAI has IP Address 192.168.0.110. I see a ton of reference to this IP under the Foreign Address column, but the status is FIN_WAIT_2 (I don't know what this means). My other Modbus devices work properly and use IP addresses 192.168.0.1, 192.168.0.2, etc.
Proto Local Address Foreign AddressState
TCP 0.0.0.0:135 0.0.0.0:0 LISTENING
TCP 0.0.0.0:445 0.0.0.0:0 LISTENING
TCP 0.0.0.0:3389 0.0.0.0:0 LISTENING
TCP 0.0.0.0:5800 0.0.0.0:0 LISTENING
TCP 0.0.0.0:5900 0.0.0.0:0 LISTENING
TCP 127.0.0.1:1048 0.0.0.0:0 LISTENING
TCP 127.0.0.1:1171 127.0.0.1:1172 ESTABLISHED
TCP 127.0.0.1:1172 127.0.0.1:1171 ESTABLISHED
TCP 127.0.0.1:1173 127.0.0.1:1174 ESTABLISHED
TCP 127.0.0.1:1174 127.0.0.1:1173 ESTABLISHED
TCP 127.0.0.1:5152 0.0.0.0:0 LISTENING
TCP 127.0.0.1:5152 127.0.0.1:2703 CLOSE_WAIT
TCP 172.16.3.87:139 0.0.0.0:0 LISTENING
TCP 172.16.3.87:2906 74.125.225.149:443 TIME_WAIT
TCP 172.16.3.87:2997 74.125.225.149:443 ESTABLISHED
TCP 172.16.3.87:3016 208.85.40.20:80 TIME_WAIT
TCP 172.16.3.87:3033 74.125.225.149:443 ESTABLISHED
TCP 172.16.3.87:3034 8.27.81.126:80 CLOSE_WAIT
TCP 192.168.0.254:139 0.0.0.0:0 LISTENING
TCP 192.168.0.254:2910 192.168.0.1:502 ESTABLISHED
TCP 192.168.0.254:2911 192.168.0.2:502 ESTABLISHED
TCP 192.168.0.254:2912 192.168.0.4:502 ESTABLISHED
TCP 192.168.0.254:2913 192.168.0.9:502 ESTABLISHED
TCP 192.168.0.254:2915 192.168.0.200:502 ESTABLISHED
TCP 192.168.0.254:2999 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3001 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3002 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3003 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3004 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3005 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3006 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3007 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3008 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3009 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3010 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3011 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3012 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3013 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3014 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3015 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3017 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3018 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3020 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3021 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3022 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3023 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3024 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3025 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3026 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3027 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3028 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3029 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3030 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3031 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3032 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3035 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3036 192.168.0.110:502 FIN_WAIT_2
TCP 192.168.0.254:3037 192.168.0.110:502 ESTABLISHED
UDP 0.0.0.0:445 *:*
UDP 0.0.0.0:500 *:*
UDP 0.0.0.0:4500 *:*
UDP 127.0.0.1:123 *:*
UDP 127.0.0.1:1025 *:*
UDP 127.0.0.1:1049 *:*
UDP 127.0.0.1:1072 *:*
UDP 127.0.0.1:1154 *:*
UDP 127.0.0.1:1900 *:*
UDP 127.0.0.1:2637 *:*
UDP 172.16.3.87:123 *:*
UDP 172.16.3.87:137 *:*
UDP 172.16.3.87:138 *:*
UDP 172.16.3.87:1900 *:*
UDP 192.168.0.254:123 *:*
UDP 192.168.0.254:137 *:*
UDP 192.168.0.254:138 *:*
UDP 192.168.0.254:1900 *:*

Similar Messages

Safari 7.0.2 Location bar will not stay open and I must use command L each time to with go back or use the address bar

Safari 7.2.2 loction bar wil not stay open and I must use command L to either go back or to use the address bar

View > Show Toolbar

Firefox does not close when exited and I must use system to delete process in order to log in again.

When using either my XP or 7 computer and I exit Firefox and then try to get back in, I get a message that Firefox is already running and I must exit to log back in. I must go to the system to delete the Firefox process before I can get back into Firefox. I am using Comcast as my provider.

https://support.mozilla.com/en-US/kb/Firefox%20hangs#w_hang-at-exit

Since upgrading to 4.0 and now 5.0 tabs do not have tab close buttons and I must use CNTL-W to close open tabs, what's the problem?

Since upgrading to Firefox 4.0 the close tab button, usually in the upper right corner of the tab has been missing. I have just recently upgraded automatically to 5.0 and the tab close 'X' button is still missing from all open tabs. The only way to close a tab is to click on it and use CNTL-W to close out the tab.

Start Firefox in [[Safe Mode]] to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
* Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
* Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")
In Firefox 4 you can use one of these to start in [[Safe mode]]:
* Help > Restart with Add-ons Disabled
* Hold down the Shift key while double clicking the Firefox desktop shortcut (Windows)
* https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Firefox 3.6.3 hangs after some use. Links w/in home pg. work but dropdown menus don't. must use Cntrl/Alt/Del to get out of pg.

Firefox 3.6.3 hangs up after some use. Can't find any specific site or action that causes this. Links w/in page and menu's such as most visited, latest headlines, and links like utube, google continue to work. Drop down menus (i.e. File, Edit, Tools, Help)/ will not open and I must use Alt+Cntrl+Del to get out of the page.
== This happened ==
Every time Firefox opened
== 1 month

Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]
If it does work in Safe-mode then disable all your extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
You can use "Disable all add-ons" on the ''Safe mode'' start window.
You have to close and restart Firefox after each change via "File > Exit" (on Mac: "Firefox > Quit")

FaceTime and iCloud must be signed in to the same Apple ID to use iPhone Cellular Calls.

FaceTime and iCloud must be signed in to the same Apple ID to use iPhone Cellular Calls.
This is the error message I receive when I try to add my phone to my Mac for proximity / FaceTime audio calling. This feature worked until I changed my Apple ID. I have updated my Apple ID everywhere I can think of updating it. I've signed out of Apple ID on my Mac, deleted EVERYTHING (calendars, contacts, etc.), signed back in, etc. I've done the same with my phone, and even done a power-down / reboot and nada. I keep getting this message from the Mac.
I can't figure out where else I should look for my old Apple ID to be logged into anything or creating problems. I've gone over my iPhone and Mac and I'm at a loss. As an aside (and yes, wrong forum), have lost the ability to do SMS forwarding since the Mac no longer receives the code from my iPhone to allow this feature to work. This was lost after signing out of the Apple ID on my Mac this afternoon.
Bluetooth is turned on for both devices. Both devices are on the same WiFi network. Both devices otherwise appear to be working correctly with the exception of the problems I'm having with FaceTime and iCloud being signed into the same Apple ID (which they are).
Thanks in advance,

(By the way, I should have pointed out in my earlier posting that I'm running OS X Yosemite 10.10.3 on my Mac). I Just installed latest Yosemite update while my iPhone was switched off, and when my Mac restarted, the 'iPhone Cellular Calls' checkbox in the FaceTime preferences was checked and the problem was therefore solved. Switched on my iPhone, still fine. Relief.

Using Quicken to manage a bank account, I get an error message from the bank that cookies and javascript must be enabled, but I don't get that message when I connect with Internet Explorer.

Firefox allows me to get the bank home page through Quicken. But when I try to login, the error message appears saying "cookies and javascript" must be enabled. I have Java on my system, but in Firefox under "tools/options/ I don't find any way to "enable" javascript. I have enabled "cookies".
I have no problem logging in at the bank site using Internet Explorer, but to use it, I have to designate it as the "default browser" before connecting through Quicken. I'd rather keep Firefox as the default.
A bank tech representative was unable to find any commands in Firefox that would deal with this problem, although she clearly had manuals for both Internet Explorer and Firefox. So she concluded that I would have to use Explorer for this operation, since it allowed control of security level settings. She said that in Explorer, security level should be set to medium.
Is there some similar control in Firefox?

Firefox uses the same "security level" setting that is set in IE.
Tools > Options > '''Content''' 
Is '''Enable Javascript''' check-marked?
http://kb.mozillazine.org/JavaScript_is_not_Java
If that doesn't solve your problem, do you have that problem when running in the Firefox SafeMode? 
[http://support.mozilla.com/en-US/kb/Safe+Mode] 
''Don't select anything right now, just use "Continue in SafeMode."''
If not, see this: 
[http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes]

Cannot Turn On iPhone Cellular Calls - FaceTime and iCloud must be signed in to the same Apple ID to use iPhone Cellular Calls.

Cannot Turn On iPhone Cellular Calls - FaceTime and iCloud must be signed in to the same Apple ID to use iPhone Cellular Calls.
I *AM* signed into Facetime and iCloud using the same Apple ID. Why am I receiving this error all of a sudden? I make calls using my Mac and need this feature. I have tried disabling and re-enabling both over a dozen times. TRUST ME, it is NOT user error -- it is Apple releasing features before they are fully ready error!

I'm pretty sure we can clarify whether or not we are on a Public Beta or not, despite NDA........
From the FAQ: https://appleseed.apple.com/sp/betaprogram/faq
Quote:
Is the public beta software I am installing confidential?
Yes, the public beta software is Apple confidential information. For example, don’t install the public beta software on any systems you don't directly control or that you share with others. Don’t blog, post screen shots, tweet, or publicly post information about the public beta software, and don't discuss the public beta software with or demonstrate it to others who are not in the Apple Beta Software Program. If Apple has publicly disclosed technical information about the public beta software, it is no longer considered confidential. Read our Terms for full details

I tried to update the App that I purchased but the message told me that my Apple account is not valid for use outside of US and I must switch back to US store to able to do it. How can I switch the account from foreign countries back to US?

I tried to update the App that I purchased but the message told me that my Apple account is not valid for use outside of US and I must switch back to US store to able to do it. How can I switch the account from foreign countries back to US?

On your phone (from http://support.apple.com/kb/ht1311):
Change your iTunes Store country
Sign in to the account for the iTunes Store region you'd like to use. Tap Settings > iTunes & App Stores > Apple ID: > View Apple ID > Country/Region.
Follow the onscreen process to change your region, agree to the terms and conditions for the region if necessary, and then change your billing information.

Modbus Ethernet read and write to a Eurotherm 6180XIO Modbus server using LV8.2 shared variables

I am having EXTREME difficulty trying to establish communications with a Modbus device using LV8.2 shared variables. The device is a Eurotherm 6180XIO Datalogger configured as a Modbus master. The PC and a cFP-1804 are slaves. All IP addresses are set correctly. This approach using shared variables would seem simple, but I can't find any examples or proper guidance on how to get it working. I am trying to avoid having to mess around with TCP/IP, OPC, or any other old-fashioned method.
I have read many threads on related topics but none directly apply to this situation. I have created a library containing a Modbus I/O server and shared variables bound to read and write holding registers. I have followed all recommended tips for creating such variables but I can neither read or write data. All data types are U16 due to Modbus protocol limitations. I have also applied the LV x10 factor in the most significant digit in the register offset (6 digits instead of 5).
I have a cFP-1804 on the same network which reads into the datalogger OK. The registers I use are 31000 (for CH0 on module 0, 31002 for CH1, etc) and the data can be read as FLOAT32. I have updated the firmwate on the 1804 to the latest level. I cannot even get shared variables to read SGL values. Using registers 301001 for CH0 and 301002 for CH1 I can only read U16 values, and not a 2-word SGL.
Third party Modbus simulation software is able to write to and read from registers very easily, but not LabVIEW.
Some questions are:
- do I use a Modbus master or slave as an I/O server in the library as a target for binding the shared variables?
- is there some other wierd translation in register offsets between LabVIEW and traditional Modbus?
- is this actually possible using shared variables or am I wasting my time?

Sending the whole 60-character string using a string or array would be the most efficient. I have tried both methods, and these only cause the datalogger to flag a message log but no text is displayed.
For a string variable, I have used the following binding "My Computer\Modbus Test.lvlib\ModbusServer6180\442305", where ModbusServer6180 is a Modbus I/O server configured with the logger IP address, and 42304 is the register offset at the start of the text block in the logger. I need to write to 30 consecutive registers starting with this one. I am not using buffering and have not enabled single writer.
Can anyone confirm whether this method should work in 8.2?
Does the string need a special termination character?

When I try to play some of the songs in my itunes library, I get a prompt saying the file could not be used. When I hit the "locate" button, it still won't locate the file. I didn't delete any of these tracks and there is no common link between them.

When I try to play some of the songs in my itunes library, I get a prompt saying the file cannot be used. When I hit the locate button, the file cannot be found. I didn't delete any songs/files and there is no common link between the missing songs.

Hello there, Paso Kid.
The following Knowledge Base articles provide some assistance with locating content in your iTunes Library:
iTunes: Finding lost media and downloads
http://support.apple.com/kb/TS1408
and
Where are my iTunes files located?
http://support.apple.com/kb/HT1391
If you have already reviewed those steps and still cannot find the songs you purchased from iTunes, delete the songs and download them again using the information in this article:
iTunes 11 for Windows: Download previous purchases from the iTunes Store
http://support.apple.com/kb/PH12491
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Re: How do you create and use "common" type classes?

Hi,
You have 2 potential solutions in your case :
1- Sub-class TextNullable class of Framework and add your methods in the
sub-class.
This is the way Domain class work. Only Nullable classes are sub-classable.
This is usefull for Data Dictionary.
The code will be located in any partition that uses or references the supplier
plan.
2- Put your add on code on a specific class and instanciate it in your user
classes (client or server).
You could also use interface for a better conception if needed. The code will
also be in any partition that uses or references the supplier plan where your
add on class is located.
If you don't want that code to be on each partition, you could use libraries :
configure as library the utility plan where is your add-on class.
You can find an example of the second case (using a QuickSort class,
GenericArray add-on) with the "QuickSort & List" sample on my personal site
http://perso.club-internet.fr/dnguyen/
Hope this helps,
Daniel Nguyen
Freelance Forte Consultant
http://perso.club-internet.fr/dnguyen/
Robinson, Richard a écrit:
I'm relatively new to forte and I'd like to know how can you handle utility
type classes that you want to use through out your application? Ideally
what I want is a static class with static methods.
Let's say that I have a StringUtil class that has a bunch of methods for
manipulating strings.
My problem is that we have code that runs on the client and code that runs
on the server. Both areas could use the StringUtil class, but from what I
understand, I have to create StringUtil in a plan and then create a server
object of type StringUtil. The server object will eventually get assigned
to a partition. That's not good since I really want the server object to
physically reside at the server end and at the client end. (Actually, I
don't want a server object, I just want to invoke a static method of a
static class).
Any clues on how to solve this problem would be appreciated.
Also, what is the url at Sage-it that has a summary of all emails that have
been posted to [email protected]? Perhaps this question has been
answered previously.
Thanks in advance
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>-
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Hi Richard,
Your question about "utility classes" brings up a number of issues, all of
which are important to long-term success with Forte.
There is no such thing as a static method (method that is associated with a
class but without an implicit object reference - this/self/me "pointer") in
TOOL, nor is there such thing as a global method (method not associated
with a class at all). This is in contrast to C++, which has both, and
Java, which has static methods, but not global classes. Frequently, Forte
developers will write code like this:
result, num : double;
// get initial value for num....
tmpDoubleData : DoubleData = new;
tmpDoubleData.DoubleValue = num;
result = tmpDoubleData.Sqrt().DoubleValue;
tmpDoubleData = NIL; // send a hint to the garbage collector
in places where a C++ programmer would write:
double result, num;
// get initial value for num....
result = Math::Sqrt(num);
or a Java programmer would write:
double result, num;
// get initial value for num....
result = Math.sqrt(num);
The result of this is that you end up allocating an extra object now and
then. In practice, this is not a big deal memory-wise. If you have a
server that is getting a lot of hits, or if you are doing some intense
processing, then you could pre-allocate and reuse the data object. Note
that optimization has its own issues, so you should start by allocating
only when you need the object.
If you are looking for a StringUtil class, then you will want to use an
instance of TextData or TextNullable. If you are looking to add methods,
you could subclass from TextNullable, and add methods. Note that you will
still have to instantiate an object and call methods on that object.
The next issue you raise is where the object resides. As long as you do
not have an anchored object, you will always have a copy of an object on a
partition. If you do not pass the object in a call to another partition,
the object never leaves. If you pass the object to another partition, then
the other partition will have its own copy of the object. This means that
the client and the server will have their own copies, which is the effect
you are looking for.
Some developers new to Forte will try to get around the lack of global
methods in TOOL by creating a user-visible service object and then calling
methods on it. If you have a general utility, like string handling, this
is a bad idea, since a service object can reside only on a single
partition.
Summary:
* You may find everything you want in TextData.
* Unless you anchor the object, the instance will reside where you
intuitively expect it.
* To patch over the lack of static methods in TOOL, simply allocate an
instance when required.
Feel free to email me if you have more questions on this.
At the bottom of each message that goes through the mailing list server,
the address for the list archive is printed:
http://pinehurst.sageit.com/listarchive/.
Good Luck,
CSB
-----Original Message-----
From: Robinson, Richard
Sent: Tuesday, March 02, 1999 5:44 PM
To: '[email protected]'
Subject: How do you create and use "common" type classes?
I'm relatively new to forte and I'd like to know how can you handle utility
type classes that you want to use through out your application? Ideally
what I want is a static class with static methods.
Let's say that I have a StringUtil class that has a bunch of methods for
manipulating strings.
My problem is that we have code that runs on the client and code that runs
on the server. Both areas could use the StringUtil class, but from what I
understand, I have to create StringUtil in a plan and then create a server
object of type StringUtil. The server object will eventually get assigned
to a partition. That's not good since I really want the server object to
physically reside at the server end and at the client end. (Actually, I
don't want a server object, I just want to invoke a static method of a
static class).
Any clues on how to solve this problem would be appreciated.
Also, what is the url at Sage-it that has a summary of all emails that have
been posted to [email protected]? Perhaps this question has been
answered previously.
Thanks in advance

My iPhone 5s was bought with full price in the USA from Sprint, and I was told that it is a global phone. And I can use it in china. But I can not use it in the USA, so could you mind help me to solve that problem. I think someone of you must help me to

My iPhone 5s was bought with full price in the USA from Sprint, and I was told that it is a global phone. And I can use it in china.
But I can not use it in the USA, so could you mind help me to solve that problem.
I think someone of you must help me to solve this problem !
Details:
SN:F2*****FDR
<Edited by Host>

See the response in your other thread:
https://discussions.apple.com/message/24641427#24641427

Changed group membership in WGM 10.6.3 from the 10.6 server. The change takes overnight to work. Formerly ran WGM from my 10.6.8 mac (worked perfectly) but now I am at 10.7.5 and must use WGM on the server. Has anyone else seen this behavior?

Changed group membership in WGM 10.6.3 from the 10.6 server. The change takes overnight to work. Formerly ran WGM from my 10.6.8 mac (worked perfectly) but now I am at 10.7.5 and must use WGM on the server. Has anyone else seen this behavior?

Hi
"Changed group membership in WGM 10.6.3 from the 10.6 server. The change takes overnight to work"
If I've understood you correctly I've never known this or anything else to take that long? What were you trying to do exactly?
"Formerly ran WGM from my 10.6.8 mac (worked perfectly) but now I am at 10.7.5 and must use WGM on the server. Has anyone else seen this behaviour?"
http://support.apple.com/kb/HT1822
HTH?
Tony

I am trying connect to a SQL instance for our CRM program and I am receiving To Connect to this Server you must use SQL Management Studio or SQL Server Management

I am trying connect to a SQL instance for our CRM program and I am receiving To Connect to this Server you must use SQL Management Studio or SQL Server Management
This is a Brand new Server 2012 that is running our CRM product and it is trying to connect to a Server 2008 R2 server with SQL Server 2008 R2 SP2 instance (10.50.4000)
I have seen this in the past where it needed the 2005 backwards compatibility components installed but those are not supported on 2012 server and this is not a 2005 SQL instance.
I am trying to install the Shared Management Objects for SQL Server 2008 but it tells me I need to install the CLR types, which I did install. But it continues to tell me to install the CLR types.
Has anyone ran into any issues like this? (this happens trying to connect to multiple SQL Servers from this new 2012 Server)
Thanks!
-Max

Hello,
Which version and edition of the SQL Server instance did you installed on the new server machine? If you install SQL Server 2012 Express edition, you can try to install SQL Server Management Studio 2012 from
this link.
You can connect to SQL Server 2008 R2 or earily verions with SSMS 2012.
What's more, Microsoft SQL Server 2008 Management Objects Collection requires Microsoft Core XML Services (MSXML) 6.0, Microsoft SQL Server Native Client, and Microsoft SQL Server System CLR Types. You can try to download and install
SQL Serve 2008 Feature Pack
which contains packages above.
Regards,
Fanny Liu
Fanny Liu
TechNet Community Support

VBAI GigE and Modbus must use common NIC?

Similar Messages

Maybe you are looking for