Virtual wireless controller

Hi.. i have running cisco vWLC controller in my location A, its working perfectly here. Now i have another location B where i have APs registered with controller in location A. I have created another WLAN and set location B dhcp server assign location B network ip. But issue is that when we connect to this wlan it gets connected but no ip gets assigned. wireless controlloer can reach to location B dhcp server, there is no connectivity issue b/w these.
what else settings do i need to set so that clients can get ip through dhcp.

Is location B WLAN configured with local or central switchinng?
If traffic is central switched (tunneled back to the WLC in location A) that may the problem in your case. I assume location A and B are in separate broadcast domains, so there should be an issue with the dhcp discovers from clients.
You should try to local switch the traffic for WLAN B or if it has to be central switched you should switch locally dhcp packets from clients.

Similar Messages

  • Cisco Aironet 3502i and Virtual Wireless Controller- Question

    Hello everyone,
    As soon, I purchased two Cisco 3502i and Cisco 1142 however, two issue are that I don't have controller and smartnet. As my purpose, it using for Home Use but house with 2,500 Sq ft with two floor and new 24x24ft garage with two floor. I put two Cisco 3502i for garage and one cisco 1142 in house on second floor. Separated for multi media, gaming, streaming high resolution video, parts, and downloads programmings online. It will run with Cisco Catalyst Express 500 with 24 ports (4 POE) and two gigabit ports. In house, it have Dell Poweredge 2850, Cisco Catalyst Express 500 with 24 ports POE and 2 ports gigabit.
    I thought to make my own developing with my first time using Wireless Controller. I wanted to try out with Virtual WLC on Dell Poweredge 2850 running ESXi 4.1.
    Specs for Dell Poweredge 2850:
    - 2x Intel Xeon Dual Core 3.8 GHz
    - 4GB RAM (Will upgrade to 12GB soon)
    - 2x 146GB and 2x 36GB SCSI
    - 2x 1 Gbps built in and 4x 1 Gbps PCI-X
    Developing with Untangle and pfSense to make it support with LADP and VLAN to both Cisco Express 500 using 4 gbps PCI-X. I have read the requipment list to use Virtual WLC but it seem met the requipment for my 2850. If someone offer me to get Virtual WLC and IOS from their, I accept to "borrow" it. I do go college which is Rochester Institute of Technology at New York and my major is Applied Computer Technology. I live here at Hampton Road, Virginia. Just in case if you might know about RIT. I just start to learning myself with Cisco books.
    I have a question:
    - Is there possible to get trial or full version of Virtual WLC?
    - Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
    -  Does it supported Dell PowerEdge 2850?
    - Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
    Thanks
    Gage

    Answers in-line...
    I have a question:
    - Is there possible to get trial or full version of Virtual WLC?
    No.  You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco.  Nobody will provide this to you.
    - Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
    No.  You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco. 
    Nobody will provide this to you.
    -  Does it supported Dell PowerEdge 2850?
    Cisco doesn't go in to great detail regarding the actual Hardware requirements of the vWLC (as far as ESX Host requirements).  Primarily, making sure you are running ESX 4.x/5.x is necessary.  The vWLC provisions 2Gb of RAM and 8GB of thick provisioned storage, so if your host can accomodate I don't see any reason it wouldn't work.
    - Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
    Yes, with the latest versions of IOS 15.2(2)JB, full functionality in autonomous can be achieved on the 1550, 3500, and 3600 series APs
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/15.2_2_JB.html#wp355587

  • Cisco Virtual Wireless Controller

                       Hello,
    Does the Cisco Virtual WLC support the 1230AP?
    There is a list of supported AP's from the data sheet the1230 isnt listed, maybe shoould assume no support?!
    http://http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps6302/ps8322/ps12723/data_sheet_c78-714543.html
    Regards,
    Garry.

    no, it doesn't.  But it has to do with the 7.3 code, as that is the lowest code the vWLC can run.
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn73.html
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Cisco Virtual Wireless Controller Vs Hardware Controller

    Our WiSM needs to be upgraded.
    We were given a choice of virtual (cheaper)  or hardware controller.
    We were told that the virtual controller is designed differently and the usual traffic does not go through the controller.
    question:
    how does this impact security or other features of cisco wireless solution?
    and if you have any other comments/experience  with the virtual controller
    THANKS

    I can't really comment on the security question, other than, it depends on your network design :)
    Regarding features, if you already manage a controller and know the required features, you find here a good comparison of all controllers and its features:
    http://www.cisco.com/c/en/us/products/wireless/buyers-guide.html#~controllers
    I think the feature in question was "Central Mode" which the virtual one lacks. The more modern (or actually the way it was before we had controllers) is "Flex Connect". In this mode the data will be put in the correct VLAN directly at the port the access point is connected to. That means that you will need to configure a Trunk port on the Switch for each AP. Depending on your building security, that could be seen as an issue. You could protect that with 802.1x between AP and Switch.

  • Cisco Virtual Wireless Controller licensing

    Hello everyone!
    We are about to start using vWLC, currently using default 60 days evaluation license
    There are couple of questions regarding licensing:
    1. Will the serial number change if we migrate the virtual machine from one host to another or if it rehosts automatically?
    2. If yes, what to do with the license? It is tied to the serial number as far as I know. Is there any way to generate a new license when the serial number changes?
    Thank you!

    I have received a license for vWLC but I entered the wrong Serial Number during the registration process and I have just realized it. I tried to rehost the license on cisco.com, entered UDI and correct serial number, received the new license and when I try to install it I received this error:
    Failed license installation at index:0 : UDI in license line does not match with the local udi
    My current UDI is AIR-CTVM-K9, but during the rehost process this UDI was rejected and I used L-LIC-CTVM-UPG. I successfully received the new license file, but I can not install it with the error described before.
    Is there anything we can do about it?

  • Virtual Wireless LAN Controllers

    Hi Guys,
    Are all APs supported by Physical WLC also supported by the Virtual WLC? or they support a selective few?
    Thanks in Advance
    Chandimal

    Hi Chandimal,
    Adding to Leo, vWLC only support FlexConnect mode AP.
    Here is the WLC compatibility matrix where you can find which AP model support under which version of WLC code.
    http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
    here is a vWLC deployment guide which may help you as well.
    http://www.cisco.com/c/en/us/support/docs/wireless/virtual-wireless-controller/113677-virtual-wlan-dg-00.html
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Virtual interface ip of Wireless controller

    Hi,
    In our wireless controller, there is a virtual interface having ip 192.168.100.1.
    when tracing the packets, we saw this ip being reflected in sniffer as dhcp server address instead of original dhcp server ip.
    The controller interfaces of ssid have original dhcp server ip ( 172.16.31.2 ) mentioned in them, this is where clients get there ip from.
    In this case, why does virtual interface ip (192.168.100.1) is seen as dhcp server in sniffer traces instead of original dhcp server 172.16.31.2
    Appreciate all inputs to help me understand this.

    If you have dhcp proxy enabled in the WLC, which is default, the WLC will proxy dhcp and it uses the virtual IP address. If you look at a client that is connected to the wireless and on a windows machine you look at the ipconfig /all, you will also see that the dhcp server is the virtual IP address if the WLC. Dhcp proxy can be disabled as long as you dint have the WLC being used as the dhcp server, or else it it's required to have dhcp proxy enabled.
    Virtual IP is also used for mobility and guest portal page.
    Sent from Cisco Technical Support iPhone App

  • Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?

    Hi!
    I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
    I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
    Log from AP:
    using ÿÿÿÿ ddr static values from serial eeprom
    ddr init done
    Running Normal Memtest...
    Passed.
    IOS Bootloader - Starting system.
    FLASH CHIP:  Numonyx P33
    Checking for Over Erased blocks
    Xmodem file system is available.
    DDR values used from system serial eeprom.
    WRDTR,CLKTR: 0x83000800, 0xc0000000
    RQDC, RFDC : 0x80000037, 0x00000184
    PCIE0: link is up.
    PCIE0: VC0 is active
    PCIE1: link is NOT up.
    PCIE1 port 1 not initialize
    PCIEx: initialization done
    flashfs[0]: 6 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 32385024
    flashfs[0]: Bytes used: 2369024
    flashfs[0]: Bytes available: 30016000
    flashfs[0]: flashfs fsck took 21 seconds.
    Reading cookie from system serial eeprom...Done
    Base Ethernet MAC address: 44:2b:03:dc:09:25
    Ethernet speed is 1000 Mb - FULL duplex
    Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
    File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
    y point: 0x4000
    executing...
    enet halted
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
    SE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 01-Jun-10 12:53 by prod_rel_team
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    FLASH CHIP:  Numonyx P33
    Checking for Over Erased blocks
    flashfs[1]: 6 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 32126976
    flashfs[1]: Bytes used: 2369024
    flashfs[1]: Bytes available: 29757952
    flashfs[1]: flashfs fsck took 7 seconds.
    flashfs[1]: Initialization complete.
    flashfs[2]: 0 files, 1 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 11999232
    flashfs[2]: Bytes used: 1024
    flashfs[2]: Bytes available: 11998208
    flashfs[2]: flashfs fsck took 1 seconds.
    flashfs[2]: Initialization complete....done Initializing flashfs.
    Ethernet speed is 1000 Mb - FULL duplex
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1041N-E-K9    (PowerPC405ex) processor (revision B0) with 98294K/32
    768K bytes of memory.
    Processor board ID FCZ1611W414
    PowerPC405ex CPU at 333Mhz, revision number 0x147E
    Last reset from reload
    LWAPP image version 7.0.94.21
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 44:2B:03:DC:09:25
    Part Number                          : 73-14034-04
    PCA Assembly Number                  : 800-34273-05
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC16075VZ3
    Top Assembly Part Number             : 800-34284-03
    Top Assembly Serial Number           : FCZ1611W414
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1041N-E-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:09.574: *** CRASH_LOG = YES
    Base Ethernet MAC address: 44:2B:03:DC:09:25
    *Mar  1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
    (contains, 1024 messages)
    *Mar  1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
    to up
    *Mar  1 00:00:11.892: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
    SE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 01-Jun-10 12:53 by prod_rel_team
    *Mar  1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
    ernet0, changed state to up
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    *Mar  1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
    IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
    *Mar  1 00:09:08.282:  -Verify the required power-injector is installed on this
    port: AIR-CT5508-K9(Gig 0/0/2).
    *Mar  1 00:09:08.282:  -If a power-injector is installed, issue the command:"pow
    er inline negotiation injector installed"
    *Mar  1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
    static IP. Forcing AP to use DHCP.
    *Mar  1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    Not in Bound state.
    *Mar  1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
    . Renewing DHCP IP.
    logs from wireless controller:
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Gu
    est
    ap-manager                       2    untagged 209.165.200.231 Dynamic Yes    No
    management                       1    untagged 209.165.200.230 Static  Yes    No
    service-port                     N/A  N/A      192.168.1.157   Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    (Cisco Controller) >
    i conect with service-port ok  and the management port works, i think.
    AP442b.03dc.0925>ping 209.165.200.230
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    AP442b.03dc.0925>
    Help, please!
    i write in spanish:
    Hola:
    Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, Gracias

    Hi!
    I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by  DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
    I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
    Before the logs, I see this message from AP:
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 
    Hola:
    He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
    Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
    Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 
    Un saludo
    Antonio R.
    (Cisco Controller) >show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"    , DESCR: "Cisco Wireless Controller"
    PID: AIR-CT5508-K9,  VID: V02,  SN: FCW1608L05X
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console
    1.27
    Build Type....................................... DATA + WPS
    System Name...................................... CISCO-CAPWAP-CONTROLLER
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 209.165.200.230
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 0 hrs 17 mins 45 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
    Rome, Vienna
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... ES  - Spain
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +23 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Disabled
    Number of WLANs.................................. 1
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Network Information
    RF-Network Name............................. hosp
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Fast SSID Change ........................... Disabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType
    1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     1000BaseTX
    2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    4  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    5  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    6  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    7  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    8  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    Press Enter to continue or to abort
    AP Summary
    Number of APs.................................... 0
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots  AP Model             Ethernet MAC       Location
         Port  Country  Priority
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    AP Location
    Site Name........................................ default-group
    Site Description.................................
    WLAN ID          Interface          Network Admission Control
    1               management           Disabled
    AP Name             Slots  AP Model             Ethernet MAC       Location
         Port  Country  Priority  GroupName
    Press Enter to continue or to abort
    AP Config
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    AP Airewave Director Configuration
    Press Enter to continue or to abort
    802.11a Configuration
    802.11a Network.................................. Disabled
    11nSupport....................................... Enabled
          802.11a Low Band........................... Enabled
          802.11a Mid Band........................... Enabled
          802.11a High Band.......................... Enabled
    802.11a Operational Rates
        802.11a 6M Rate.............................. Mandatory
        802.11a 9M Rate.............................. Supported
        802.11a 12M Rate............................. Mandatory
        802.11a 18M Rate............................. Supported
        802.11a 24M Rate............................. Mandatory
        802.11a 36M Rate............................. Supported
        802.11a 48M Rate............................. Supported
        802.11a 54M Rate............................. Supported
    802.11n MCS Settings:
        MCS 0........................................ Supported
        MCS 1........................................ Supported
        MCS 2........................................ Supported
        MCS 3........................................ Supported
        MCS 4........................................ Supported
        MCS 5........................................ Supported
        MCS 6........................................ Supported
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
        MCS 7........................................ Supported
        MCS 8........................................ Supported
        MCS 9........................................ Supported
        MCS 10....................................... Supported
        MCS 11....................................... Supported
        MCS 12....................................... Supported
        MCS 13....................................... Supported
        MCS 14....................................... Supported
        MCS 15....................................... Supported
    802.11n Status:
        A-MPDU Tx:
            Priority 0............................... Enabled
            Priority 1............................... Disabled
            Priority 2............................... Disabled
            Priority 3............................... Disabled
            Priority 4............................... Disabled
            Priority 5............................... Disabled
            Priority 6............................... Disabled
            Priority 7............................... Disabled
    Beacon Interval.................................. 100
    CF Pollable mandatory............................ Disabled
    CF Poll Request mandatory........................ Disabled
    CFP Period....................................... 4
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
    CFP Maximum Duration............................. 60
    Default Channel.................................. 36
    Default Tx Power Level........................... 0
    DTPC  Status..................................... Enabled
    Fragmentation Threshold.......................... 2346
    TI Threshold..................................... -50
    Legacy Tx Beamforming setting.................... Disabled
    Traffic Stream Metrics Status.................... Disabled
    Expedited BW Request Status...................... Disabled
    World Mode....................................... Enabled
    EDCA profile type................................ default-wmm
    Voice MAC optimization status.................... Disabled
    Call Admision Control (CAC) configuration
    Voice AC:
       Voice AC - Admission control (ACM)............ Disabled
       Voice max RF bandwidth........................ 75
       Voice reserved roaming bandwidth.............. 6
       Voice load-based CAC mode..................... Disabled
       Voice tspec inactivity timeout................ Disabled
       Voice Stream-Size............................. 84000
       Voice Max-Streams............................. 2
    Video AC:
       Video AC - Admission control (ACM)............ Disabled
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
       Video max RF bandwidth........................ Infinite
       Video reserved roaming bandwidth.............. 0
    Press Enter to continue or to abort
    802.11a Advanced Configuration
    Press Enter to continue or to abort
    802.11a Airewave Director Configuration
    RF Event and Performance Logging
      Channel Update Logging......................... Off
      Coverage Profile Logging....................... Off
      Foreign Profile Logging........................ Off
      Load Profile Logging........................... Off
      Noise Profile Logging.......................... Off
      Performance Profile Logging.................... Off
      TxPower Update Logging......................... Off
    Default 802.11a AP performance profiles
      802.11a Global Interference threshold.......... 10 %
      802.11a Global noise threshold................. -70 dBm
      802.11a Global RF utilization threshold........ 80 %
      802.11a Global throughput threshold............ 1000000 bps
      802.11a Global clients threshold............... 12 clients
    Default 802.11a AP monitoring
      802.11a Monitor Mode........................... enable
      802.11a Monitor Mode for Mesh AP Backhaul...... disable
      802.11a Monitor Channels....................... Country channels
      802.11a AP Coverage Interval................... 180 seconds
      802.11a AP Load Interval....................... 60 seconds
      802.11a AP Noise Interval...................... 180 seconds
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
      802.11a AP Signal Strength Interval............ 60 seconds
    Automatic Transmit Power Assignment
      Transmit Power Assignment Mode................. AUTO
      Transmit Power Update Interval................. 600 seconds
      Transmit Power Threshold....................... -70 dBm
      Transmit Power Neighbor Count.................. 3 APs
      Min Transmit Power............................. -10 dBm
      Max Transmit Power............................. 30 dBm
      Transmit Power Update Contribution............. SNI.
      Transmit Power Assignment Leader............... c4:64:13:8f:93:40
      Last Run....................................... 75 seconds ago
    Coverage Hole Detection
      802.11a Coverage Hole Detection Mode........... Enabled
      802.11a Coverage Voice Packet Count............ 100 packets
      802.11a Coverage Voice Packet Percentage....... 50%
      802.11a Coverage Voice RSSI Threshold.......... -80 dBm
      802.11a Coverage Data Packet Count............. 50 packets
      802.11a Coverage Data Packet Percentage........ 50%
      802.11a Coverage Data RSSI Threshold........... -80 dBm
      802.11a Global coverage exception level........ 25 %
      802.11a Global client minimum exception lev.... 3 clients
    Automatic Channel Assignment
      Channel Assignment Mode........................ AUTO
    --More or (q)uit current module or to abort
      Channel Update Interval........................ 600 seconds [startup]
      Anchor time (Hour of the day).................. 0
      Channel Update Contribution.................... SNI.
      Channel Assignment Leader...................... c4:64:13:8f:93:40
      Last Run....................................... 75 seconds ago
      DCA Sensitivity Level.......................... STARTUP (5 dB)
      DCA 802.11n Channel Width...................... 20 MHz
      DCA Minimum Energy Limit....................... -95 dBm
      Channel Energy Levels
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      Channel Dwell Times
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      802.11a 5 GHz Auto-RF Channel List
        Allowed Channel List......................... 36,40,44,48,52,56,60,64
        Unused Channel List.......................... 100,104,108,112,116,120,124,
                                                      128,132,136,140
      DCA Outdoor AP option.......................... Disabled
    Radio RF Grouping
      802.11a Group Mode............................. AUTO
    --More or (q)uit current module or to abort
      802.11a Group Update Interval.................. 600 seconds
      802.11a Group Leader........................... c4:64:13:8f:93:40
        802.11a Group Member......................... c4:64:13:8f:93:40
      802.11a Last Run............................... 75 seconds ago
    802.11b Configuration
    802.11b Network.................................. Enabled
    11gSupport....................................... Enabled
    11nSupport....................................... Enabled
    802.11b/g Operational Rates
        802.11b/g 1M Rate............................ Mandatory
        802.11b/g 2M Rate............................ Mandatory
        802.11b/g 5.5M Rate.......................... Mandatory
        802.11b/g 11M Rate........................... Mandatory
        802.11g 6M Rate.............................. Supported
        802.11g 9M Rate.............................. Supported
        802.11g 12M Rate............................. Supported
        802.11g 18M Rate............................. Supported
        802.11g 24M Rate............................. Supported
        802.11g 36M Rate............................. Supported
        802.11g 48M Rate............................. Supported
        802.11g 54M Rate............................. Supported
    802.11n MCS Settings:
        MCS 0........................................ Supported
        MCS 1........................................ Supported
        MCS 2........................................ Supported
        MCS 3........................................ Supported
        MCS 4........................................ Supported
    --More or (q)uit current module or to abort
        MCS 5........................................ Supported
        MCS 6........................................ Supported
        MCS 7........................................ Supported
        MCS 8........................................ Supported
        MCS 9........................................ Supported
        MCS 10....................................... Supported
        MCS 11....................................... Supported
        MCS 12....................................... Supported
        MCS 13....................................... Supported
        MCS 14....................................... Supported
        MCS 15....................................... Supported
    802.11n Status:
        A-MPDU Tx:
            Priority 0............................... Enabled
            Priority 1............................... Disabled
            Priority 2............................... Disabled
            Priority 3............................... Disabled
            Priority 4............................... Disabled
            Priority 5............................... Disabled
            Priority 6............................... Disabled
            Priority 7............................... Disabled
    Beacon Interval.................................. 100
    CF Pollable mode................................. Disabled
    --More or (q)uit current module or to abort
    CF Poll Request mandatory........................ Disabled
    CFP Period....................................... 4
    CFP Maximum Duration............................. 60
    Default Channel.................................. 1
    Default Tx Power Level........................... 0
    DTPC  Status..................................... Enabled
    Call Admission Limit  ........................... 105
    G711 CU Quantum ................................. 15
    ED Threshold..................................... -50
    Fragmentation Threshold.......................... 2346
    PBCC mandatory................................... Disabled
    RTS Threshold.................................... 2347
    Short Preamble mandatory......................... Enabled
    Short Retry Limit................................ 7
    Legacy Tx Beamforming setting.................... Enabled
    Traffic Stream Metrics Status.................... Disabled
    Expedited BW Request Status...................... Disabled
    World Mode....................................... Enabled
    Faster Carrier Tracking Loop..................... Disabled
    EDCA profile type................................ default-wmm
    Voice MAC optimization status.................... Disabled
    Call Admision Control (CAC) configuration
       Voice AC - Admission control (ACM)............ Disabled
    --More or (q)uit current module or to abort
       Voice Stream-Size............................. 84000
       Voice Max-Streams............................. 2
       Voice max RF bandwidth........................ 75
       Voice reserved roaming bandwidth.............. 6
       Voice load-based CAC mode..................... Disabled
       Voice tspec inactivity timeout................ Disabled
       Video AC - Admission control (ACM)............ Disabled
       Video max RF bandwidth........................ 50
       Video reserved roaming bandwidth.............. 0
    802.11b Advanced Configuration
    Press Enter to continue or to abort
    802.11b Airewave Director Configuration
    RF Event and Performance Logging
      Channel Update Logging......................... Off
      Coverage Profile Logging....................... Off
      Foreign Profile Logging........................ Off
      Load Profile Logging........................... Off
      Noise Profile Logging.......................... Off
      Performance Profile Logging.................... Off
      Transmit Power Update Logging.................. Off
    Default 802.11b AP performance profiles
      802.11b Global Interference threshold.......... 10 %
      802.11b Global noise threshold................. -70 dBm
      802.11b Global RF utilization threshold........ 80 %
      802.11b Global throughput threshold............ 1000000 bps
      802.11b Global clients threshold............... 12 clients
    Default 802.11b AP monitoring
      802.11b Monitor Mode........................... enable
      802.11b Monitor Channels....................... Country channels
      802.11b AP Coverage Interval................... 180 seconds
      802.11b AP Load Interval....................... 60 seconds
      802.11b AP Noise Interval...................... 180 seconds
      802.11b AP Signal Strength Interval............ 60 seconds
    Automatic Transmit Power Assignment
      Transmit Power Assignment Mode................. AUTO
      Transmit Power Update Interval................. 600 seconds
      Transmit Power Threshold....................... -70 dBm
      Transmit Power Neighbor Count.................. 3 APs
      Min Transmit Power............................. -10 dBm
      Max Transmit Power............................. 30 dBm
      Transmit Power Update Contribution............. SNI.
      Transmit Power Assignment Leader............... c4:64:13:8f:93:40
      Last Run....................................... 213 seconds ago
    Coverage Hole Detection
      802.11b Coverage Hole Detection Mode........... Enabled
      802.11b Coverage Voice Packet Count............ 100 packets
      802.11b Coverage Voice Packet Percentage....... 50%
      802.11b Coverage Voice RSSI Threshold.......... -80 dBm
      802.11b Coverage Data Packet Count............. 50 packets
      802.11b Coverage Data Packet Percentage........ 50%
      802.11b Coverage Data RSSI Threshold........... -80 dBm
      802.11b Global coverage exception level........ 25 %
      802.11b Global client minimum exception lev.... 3 clients
    Automatic Channel Assignment
      Channel Assignment Mode........................ AUTO
      Channel Update Interval........................ 600 seconds [startup]
      Anchor time (Hour of the day).................. 0
      Channel Update Contribution.................... SNI.
      Channel Assignment Leader...................... c4:64:13:8f:93:40
      Last Run....................................... 213 seconds ago
      DCA Sensitivity Level: ...................... STARTUP (5 dB)
      DCA Minimum Energy Limit....................... -95 dBm
      Channel Energy Levels
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      Channel Dwell Times
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      802.11b Auto-RF Allowed Channel List........... 1,6,11
      Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
    Radio RF Grouping
      802.11b Group Mode............................. AUTO
      802.11b Group Update Interval.................. 600 seconds
      802.11b Group Leader........................... c4:64:13:8f:93:40
        802.11b Group Member......................... c4:64:13:8f:93:40
      802.11b Last Run............................... 213 seconds ago
    Mobility Configuration
    Symmetric Mobility Tunneling (current) .......... Enabled
    Symmetric Mobility Tunneling (after reboot) ..... Enabled
    Mobility Protocol Port........................... 16666
    Default Mobility Domain.......................... hosp
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x97e2
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 1
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address        IP Address       Group Name                        Multicast
    IP     Status
    c4:64:13:8f:93:40  209.165.200.230  hosp                              0.0.0.0
            Up
    Advanced Configuration
    Probe request filtering..........................  Enabled
    Probes fwd to controller per client per radio....  0
    Probe request rate-limiting interval.............  500 msec
    EAP-Identity-Request Timeout (seconds)........... 30
    EAP-Identity-Request Max Retries................. 2
    EAP Key-Index for Dynamic WEP.................... 0
    EAP Max-Login Ignore Identity Response........... enable
    EAP-Request Timeout (seconds).................... 30
    EAP-Request Max Retries.......................... 2
    EAPOL-Key Timeout (milliseconds)................. 1000
    EAPOL-Key Max Retries............................ 2
    dot11-padding.................................... Disabled
    Authentication Response Timeout (seconds)........ 10
    Rogue Entry Timeout (seconds).................... 1200
    AP Heart Beat Timeout (seconds).................. 30
    AP Discovery Timeout (seconds)................... 10
    AP Local mode Fast Heartbeat (seconds)........... disable
    AP Hreap mode Fast Heartbeat (seconds)........... disable
    AP Primary Discovery Timeout (seconds)........... 120
    AP Primed Join Timeout (seconds)................. 0
    Packet Forwarding watchdog timer (seconds)....... 240 (enable)
    Location Configuration
    RFID Tag data Collection......................... Enabled
    RFID  timeout.................................... 1200 seconds
    RFID mobility.................................... Oui:00:14:7e : Vendor:pango  S
    tate:Disabled
    Interface Configuration
    Interface Name................................... management
    MAC Address...................................... c4:64:13:8f:93:40
    IP Address....................................... 209.165.200.230
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 209.165.200.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 192.168.1.1
    VLAN............................................. untagged
    Quarantine-vlan.................................. 0
    Active Physical Port............................. 1
    Primary Physical Port............................ 1
    Backup Physical Port............................. Unconfigured
    Primary DHCP Server.............................. 209.165.200.230
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... Yes
    Guest Interface.................................. No
    Interface Name................................... service-port
    MAC Address...................................... c4:64:13:8f:93:41
    IP Address....................................... 192.168.1.157
    IP Netmask....................................... 255.255.255.0
    DHCP Option 82................................... Disabled
    DHCP Protocol.................................... Disabled
    AP Manager....................................... No
    Guest Interface.................................. No
    Interface Name................................... virtual
    MAC Address...................................... c4:64:13:8f:93:40
    IP Address....................................... 1.1.1.1
    DHCP Option 82................................... Disabled
    Virtual DNS Host Name............................ Disabled
    AP Manager....................................... No
    Guest Interface.................................. No
    WLAN Configuration
    WLAN Identifier.................................. 1
    Profile Name..................................... HOSP3C
    Network Name (SSID).............................. HOSP3C
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      NAC-State...................................... Disabled
      Quarantine VLAN................................ 0
    Number of Active Clients......................... 0
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    WLAN ACL......................................... unconfigured
    DHCP Server...................................... 209.165.200.230
    DHCP Address Assignment Required................. Enabled
    Quality of Service............................... Platinum (voice)
    Scan Defer Priority.............................. 5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    IPv6 Support..................................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... 802.11b and 802.11g only
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Disabled
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Enabled
             AES Cipher.............................. Enabled
          Auth Key Management
             802.1x.................................. Disabled
             PSK..................................... Enabled
             CCKM.................................... Disabled
             FT(802.11r)............................. Disabled
             FT-PSK(802.11r)......................... Disabled
    FT Reassociation Timeout......................... 20
    FT Over-The-Air mode............................. Enabled
    FT Over-The-Ds mode.............................. Enabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       H-REAP Local Switching........................ Disabled
       H-REAP Learn IP Address....................... Enabled
       Infrastructure MFP protection................. Enabled
       Client MFP.................................... Optional
       Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Band Select...................................... Enabled
    Load Balancing................................... Enabled
    Mobility Anchor List
    WLAN ID     IP Address            Status
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    ACL Configuration
    Press Enter to continue or to abort
    CPU ACL Configuration
    CPU Acl Name................................ NOT CONFIGURED
    Wireless Traffic............................ Disabled
    Wired Traffic............................... Disabled
    RADIUS Configuration
    Vendor Id Backward Compatibility................. Disabled
    Call Station Id Case............................. lower
    Call Station Id Type............................. IP Address
    Aggressive Failover.............................. Enabled
    Keywrap.......................................... Disabled
    Fallback Test:
        Test Mode.................................... Off
        Probe User Name.............................. cisco-probe
        Interval (in seconds)........................ 300
    MAC Delimiter for Authentication Messages........ hyphen
    MAC Delimiter for Accounting Messages............ hyphen
    Authentication Servers
    Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P
    hase1/Group/Lifetime/Auth/Encr
    Accounting Servers
    Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P
    hase1/Group/Lifetime/Auth/Encr
    --More or (q)uit current module or to abort
    TACACS Configuration
    Authentication Servers
    Idx  Server Address    Port    State     Tout
    Authorization Servers
    Idx  Server Address    Port    State     Tout
    Accounting Servers
    Idx  Server Address    Port    State     Tout
    LDAP Configuration
    Press Enter to continue or to abort
    Local EAP Configuration
    User credentials database search order:
        Primary ..................................... Local DB
    Timer:
        Active timeout .............................. 300
    Configured EAP profiles:
    EAP Method configuration:
        EAP-FAST:
          Server key ................................
          TTL for the PAC ........................... 10
          Anonymous provision allowed ............... Yes
          Authority ID .............................. 436973636f00000000000000000000
    00
          Authority Information ..................... Cisco A-ID
    Press Enter to continue or to abort
    HREAP Group Summary
    HREAP Group Summary: Count: 0
    Group Name                # Aps
    Press Enter to continue or to abort
    HREAP Group Detail
    Press Enter to continue or to abort
    Route  Info
    Number of Routes................................. 0
    Destination Network          Netmask               Gateway
    Press Enter to continue or to abort
    Qos Queue Length Info
    Platinum queue length............................ 100
    Gold queue length................................  75
    Silver queue length..............................  50
    Bronze queue length..............................  25
    Press Enter to continue or to abort
    Mac Filter Info
    Press Enter to continue or to abort
    Authorization List
    Authorize MIC APs against AAA ................... disabled
    Authorize LSC APs against Auth-List ............. disabled
    Allow APs with MIC - Manufactured Installed C.... disabled
    Allow APs with SSC - Self-Signed Certificate..... disabled
    Allow APs with LSC - Locally Significant Cert.... disabled
    Load Balancing Info
    Aggressive Load Balancing........................ Disabled
    Aggressive Load Balancing Window................. 5 clients
    Aggressive Load Balancing Denial Count........... 3
    Statistics
    Total Denied Count............................... 0 clients
    Total Denial Sent................................ 0 messages
    Exceeded Denial Max Limit Count.................. 0 times
    None 5G Candidate Count.......................... 0 times
    None 2.4G Candidate Count........................ 0 times
    Press Enter to continue or to abort
    Dhcp Scope Info
    Scope: PUNTOSAP
    Enabled.......................................... Yes
    Lease Time....................................... 86400 (1 day )
    Pool Start....................................... 209.165.200.201
    Pool End......................................... 209.165.200.229
    Network.......................................... 209.165.200.0
    Netmask.......................................... 255.255.255.0
    Default Routers.................................. 0.0.0.0  0.0.0.0  0.0.0.0
    DNS Domain.......................................
    DNS.............................................. 0.0.0.0  0.0.0.0  0.0.0.0
    Netbios Name Servers............................. 0.0.0.0  0.0.0.0  0.0.0.0
    Press Enter to continue or to abort
    Exclusion List ConfigurationUnable to retrieve exclusion-list entry
    Press Enter to continue or to abort
    CDP Configuration
    Press Enter to continue or to abort
    Country Channels Configuration
    Configured Country............................. ES  - Spain
          KEY: * = Channel is legal in this country and may be configured manually.
               A = Channel is the Auto-RF default in this country.
               . = Channel is not legal in this country.
               C = Channel has been configured for use by Auto-RF.
               x = Channel is available to be configured for use by Auto-RF.
             (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
        802.11bg     :
        Channels     :                   1 1 1 1 1
                     : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    ES (-E   ,-E   ): A * * * * A * * * * A * * .
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
        802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
        Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
                     : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    ES (-E   ,-E   ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
    Press Enter to continue or to abort
    WPS Configuration Summary
    Auto-Immune
      Auto-Immune.................................... Disabled
    Client Exclusion Policy
      Excessive 802.11-association failures.......... Enabled
      Excessive 802.11-authentication failures....... Enabled
      Excessive 802.1x-authentication................ Enabled
      IP-theft....................................... Enabled
      Excessive Web authentication failure........... Enabled
    Signature Policy
      Signature Processing........................... Enabled
    Press Enter to continue or to abort
    Custom Web Configuration
    Radius Authentication Method..................... PAP
    Cisco Logo....................................... Enabled
    CustomLogo....................................... None
    Custom Title..................................... None
    Custom Message................................... None
    Custom Redirect URL.............................. None
    Web Authentication Type.......................... Internal Default
    External Web Authentication URL.................. None
    Configuration Per Profile:
    Rogue AP Configuration
    Rogue Location Discovery Protocol................ Disabled
    Rogue on wire Auto-Contain....................... Disabled
    Rogue using our SSID Auto-Contain................ Disabled
    Valid client on rogue AP Auto-Contain............ Disabled
    Rogue AP timeout................................. 1200
    MAC Address        Classification     # APs # Clients Last Heard
    Adhoc Rogue Configuration
    Detect and report Ad-Hoc Networks................ Enabled
    Auto-Contain Ad-Hoc Networks..................... Disabled
    Client MAC Address  Adhoc BSSID         State              # APs   Last Heard
    Rogue Client Configuration
    Validate rogue clients against AAA............... Disabled
    Rogue Client Configuration
    Validate rogue clients against AAA............... Disabled
    --More-- or (q)uit
    MAC Address        State              # APs Last Heard
    Ignore List Configuration
    MAC Address
    Rogue Rule Configuration
    Priority Rule Name               State    Type          Match Hit Count
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console
    1.27
    Build Type....................................... DATA + WPS
    System Name...................................... CISCO-CAPWAP-CONTROLLER
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 209.165.200.230
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 0 hrs 41 mins 2 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
    Rome, Vienna
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... ES  - Spain
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +39 C
    External Temperature............................. +23 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Disabled
    Number of WLANs.................................. 1
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    (Cisco Controller) >
    The AP log
    AP442b.03dc.0925>
    *Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
    '(index 0).
    *Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    *Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
    p: 209.165.200.230 peer_port: 5246
    *Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
    peer_ip: 209.165.200.230 peer_port: 5246
    *Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
    0
    *Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
    *Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
    .165.200.230:5246
    *Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
    not established

  • Setting up 2100 wireless controller

    I have just taken delivery of  a Cisco 2106 Wireless LAN controller and two Cisco 802.11a/b/g Lightweight Access Point devices.
    I have connected the Controller to the PC and I am tyrying to configure the box.  The network we have is as follows:
    we have a fixed IP address on the router and all workstations have fixed IP addresses of the form 10.0.0.X  and get DNS from the windows SBS 2003.  The router default gateway  is 10.0.0.1.
    so to the config of the Wireless controller... I need to know the following: (my comments in [ ] ??? means I have no idea at all)  please excuse all my dumb questions
    • A management interface (DS Port or network interface port) IP address, such as 10.40.0.4 [can I use any free IP addres of the form 10.0.0.x ]
    • A management interface netmask address, such as 255.255.255.0. [same as our netwrok sub?]
    • A management interface default router IF address, such as 10.40.0.5 [again something of the form 10.0.0.x? - how is this different from DS Port?]
    • A VLAN identifier if the management interface is assigned to a VLAN, such as 40 or 0 for an untagged VLAN.[????]
    • A management interface port, such as 1. [again ????]
    • A management interface DHCP server IP address, such as 10.10.0.6 (the IP address of the default DHCP server that will supply IP addresses to clients and the management interface. [we do not use DHCP - all clients have fixed IPs so what do I do here?]
    • An access point manager interface IP address, such as 10.40.0.7. [what is this and what should I use given our network setup?]
    • A virtual gateway IP address (a fictitious, unassigned IP address, such as 1.1.1.1, used by all Cisco wireless LAN controller Layer 3 security and mobility managers). [can I use 1.1.1.1 or something else?]
    • A Cisco wireless LAN controller mobility or RF group name, such as rfgrp40 if required. An RF group name can contain up to 19 printable ASCII characters. [can I use anything and if so where and when would I use this]
    • An 802.11 network name (SSID), such as wlanl. An SSID can contain up to 32 printable, case-sensitive ASCII characters. [again, can I use anything and if so where and when would I use this]
    • Whether or not to allow static IP addresses from clients, either Yes or No. [???]
    - Yes is more convenient, but has lower security (session can be hijacked).
    - No is less convenient, but has higher security and works well for Windows XP devices.
    • RADIUS server IP address, communications port, and secret if you are configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode. [again help ???]
    • The country code for this installation. Enter help to see a list or refer to the Cisco Wireless LAN Controller Configuration Guide for country code information. This guide is available at CISCO.com [I am in the USA]
    • Status of the 802.11a, 802.11b, and 802.11g networks, either enabled or disabled [???]
    • Status of radio resource management (RRM), either enabled or disabled [???]
    THANKYOU FOR ANY HELP!!!!

    Mike,
    I have attached a link to all your questions...
    https://www.cisco.com/en/US/products/ps7206/tsd_products_support_series_home.html

  • Wireless Controller locking down User per SSID

    I am using Wireless Controller 4112. We use WPA enterprise mode for authentication and encryption via Microsoft IAS server and MS AD domain.
    My question is how to lock down a user to a specific SSID? I would guess that this is via some vendor specific radius attributes, am I right? And if so, what would be the name (and ID) for the attributes?
    Thanks in advance.

    Making progress in setting up the wireless controller with multiple VLAN and WLAN/SSID. I create a virtaul interface at the controller and assign a VLAN number to it. The controller mgmt port is also set to a trunk port. Create a new SSID WLAN and have it mapped to the new virtual interface. Things work good.
    The new problem I am trying to solve is how to prevent wired users to access the controller admin web interface via the virtual interface IP. I try create ACL and map it to the virtual interface. It doesn't seem working.

  • Virtual WLAN Controller Guest Anchor

    We are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
    We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.
    I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and can anyone advise if thsi is a supprted deployment model.

    Well you can use the vWLC to anchor to a 5508, but not the other way around. So if you use the DMZ 5508 for OfficeExtend, you will not be able to anchor the traffic back to the inside. Cisco doesn't support reverse anchoring for a Remote-LAN in OfficeExtend and requires you to actually have the OfficeExtend AP's connect to an inside WLC. In v7.0.x you were able to do this reverse anchor, but it was removed on later codes.
    Sent from Cisco Technical Support iPhone App

  • Can CSACSE-1113-K9 work as a Wireless Controller ?

    Hi all,
    Need to know that if I have a CSACSE-1113-K9 and also i have 20 units of AIR-LAP1242AG-A-K9.
    Can i utilize the CSACSE-1113-K9 Appliance to as a Wireless Controller for the AIR-LAP1242AG-A-K9 ?
    Thanks and waiting for feedback.
    Md. Sariful Islam
    +8801716631370

    Hi Sarifaul,
    Where did you hear that there is an appliance can be configured to a WLC?
    The WLC comes with its own hardware OR as a virtual machine image. The virtual WLC however has a lot of limitations.
    So, like Scott answered you, the answer to your questoin is "No".
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Access points As a Wireless Controller

    Dear
    I need a proposal for the fully meshed 9 wireless access points. In which 
    One can behave as wireless controller
    Dual Radio connectivity
    Poe on each AP or extra port of Ethernet
    Warm Regards
    Hassan Sarfraz Ali

    I see what you're asking, Since virtual controller concept is evolving and no one wants single point of failure i.e., single controller for smaller deployment and remote offices, what you're asking is quite logical for local and flex mode. For Mesh, considering awpp convergence may not suite is what i believe.
    Until 7.3 Cisco don't have this feature. Whatever you're looking could be what Cisco's future making or already work in progress, you may want to check with Cisco via TAC.

  • How do I configure the 2504 Wireless controller with AP?

    I recently purchase the 2504 wireless controller and the 1602i AP. I was able to do the basic setup of the controller and can now access the web interface, but the AP is not being detected and I am unable to add it.

    First of all: 1602 AP need minimum software version on WLC: 7.4.100.0
    paste this info:
    sh sysinfo from WLC
    sh version from AP.
    Did you create a DHCP pool for APs to get IP ?
    Try to to be keep AP and WLC on same subnet.
    regards

  • Can I move a Virtual Domain Controller from one host(Win Server 2008 R2) to another (Win Server 2012 R2) ? Are there any issues?

    Can I move a Virtual Domain Controller from one host(Win Server 2008 R2) to another (Win Server 2012 R2) ? Are there any issues?

    I also had this error: "Setup cannot continue. Your computer will now restart, and your previous version of Windows will be restored."
    trying to do a in-place upgrade of a Domain Controller Windows 2008 R2 to Windows 2012 R2.
    The problem was the separated System Reserved Partition. After I removed using this instructions:
    http://jacobackerman.blogspot.com/2012/12/how-to-remove-system-reserved-partition.html
    The upgrade ran ok, and now have my DC as Windows 2012 R2.
    Hope that helps!.

Maybe you are looking for