VPLS TLS and EVCS support?

I have been trying to read the VPLS section on the following page to what versions of VPLS are supported.
http://www.cisco.com/en/US/products/hw/routers/ps368/products_module_configuration_guide_chapter09186a00801e5c06.html
I have a few questions:
1. What flavors of VPLS does Cisco support?
2. For the config exmaple on that page, is it TLS of EVCS?
3. Can I attach multiple vlan interfaces to a VFI?
4. Related to last question, does the packet that enters the VPLS over the core maintain the VLAN header of is it stripped? I'll have more questions about this depedning on the answer I get.
5. I am seeing conflicting reports in the forum and in the docs about which SUP card I need. What do I need to get my 6509 to work with VPLS?
Thanks,
Greg

1. I apologize. I guess I should have been more clear. I understand which draft Cisco used, it was more around vlan based and port based implementations I've seen on other vendors.
2. Sorry, I meant in the VPLS section. The section was a bit confusing saying where it kept mentioning the TLS and EVCS. But it never clearly showed which lines make it EVCS and which lines make it TLS. Are you saying that EVCS is actually just a reference to Martini?
3. Thanks. I guess this means vlan headers are maintained across VPLS.
4. I think I understand now. Mainly I was trying to see if Cisco's VPLS also did the same type4(vc-type vlan) and type5(vc-type ether) as they did with Martini. From what I iunderstand, Cisco's current VPLS is type4. Correct?
5. So for VPLS, I need at least a SUP2 MSFC2 with OSM+. For Martini, if I have a SUP720-3BXL, what card can I use to support MPLS core interface? Will a standard GE card work?
Thanks,
Greg

Similar Messages

High time SPA 3102 supports TLS and SDP

There have been absolutely no firmware updates in years for SPA 3102
Its a pity that SPA 3102 doesn't support TLS + SRTP with SDP (which is the default
and widely used key exchange mechanism as supposed to some proprietary method
or MIKEY that no one supports).
Grandstream has greatly overtaken with TLS +SRTP in their HT.503 that also sells much cheaper.
I have about 20 boxes of 3102 and can't throw them. I need to buy about 12 more and wish to
have uniformity. Main problem I see with 3102 is TLS and use of SDP for SRTP key exchange.
Otherwise is a great product.
Please have your engineering team make this a high priority and try to provide firmware update
for all the 3102 hw versions.
Thanks,
Anz

> does not have the support for SRTP.
This is contrary to what a lot of information out there says. Are you sure ?!
I would like to be able to use a gateway that can talk to a 3102 using SRTP and mini-certificate without using anothe 3102. There was a mention of this by your representative himself.
I am not really interested in your upcoming ATA that is similar to SPA 3102.
Are you going to replace all my SPA 3102 for free ?!!
Why can't you just do a firwmare upgrade for SPA 3102.
Please provide accurate and proper answers, that would be appreciated.

EAP Chaining with Machine TLS and User PEAP

We are deploying an ISE based .1x. The design is to use eap-tls for machine and eap-peap for user. Apparently EAP-Chaining is recommended, but can anyone confirm if we can do chaining based on machine TLS and user PEAP. I have done some investigation and could not find any supporting document, but not any document saying not supporting either. Looking at Anyconnect profile editor, it does not look like this configuration is supported. Has anyone done this before?
Thanks a lot.

http://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise/design-zone-security/howto_80_eapchaining_deployment.pdf
Just change the authentication policy to allow the methods you want to use under eap-fast (eap-chaining) and use the same ones in your nam client configuration settings.

TLS And TCP/IP

I must use TCP/IP and TLS in a project but i can't find any help or solution how to do it.
Does any one know how to do it?

LabVIEW has no native support for TLS/SSL.
For those who need/desire such functionality, please support this Idea Exchange entry:
Native SSH and SFTP Support
Now is the right time to use %^<%Y-%m-%dT%H:%M:%S%3uZ>T
If you don't hate time zones, you're not a real programmer.
"You are what you don't automate"
Inplaceness is synonymous with insidiousness

Lync 2013 PSTN calling not working with Sonus SBC 1000 over TLS and SRTP

Dear All,
We have recently installed Lync 2013 Enterprise Edition with a Pool of 3 FE Servers (MEDIATION COLLOCATED).
We need to implement TLS and SRTP with Sonus SBC 1000. However calls are not routing b/w SBC and Lync.
We are using wild card certificate with multiple SIP Domains as SAN(s), for internal FE servers as well SBC.
Also i would like to mentioned here that inbound and outbound calls are routing properly when we tested it over TCP.
When I move to TLS Only calls from Lync to SBC (outgoing) are working without encryption.
Here are the OCS Logger traces for incoming calls which are not landing on lync:
TL_INFO(TF_PROTOCOL) [1]2C5C.0D30::04/30/2014-14:35:18.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.000265d2
(S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[3491463749]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_AE0419>], 10.10.0.11:5067->10.10.7.50:25678
SIP/2.0 400 Bad Request
FROM: "3158222726"<sip:[email protected]>;tag=ac3201ce-4d7
TO: <sip:[email protected]:5067>;epid=D2091CF753;tag=f373543c
CSEQ: 2 INVITE
CALL-ID: [email protected]
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-0b14
CONTENT-LENGTH: 0
SERVER: RTCC/5.0.0.0 MediationServer
------------EndOfOutgoing SipMessage
TL_INFO(TF_PROTOCOL) [1]2C5C.0D30::04/30/2014-14:35:18.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.000265d7
(S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2666394843]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_370F030>], 10.10.0.11:58059->10.10.0.13:5061
SERVICE sip:2138797082;[email protected];user=phone SIP/2.0
FROM: <sip:2138797082;[email protected];user=phone>;epid=DCFDB95F4C;tag=17d286a93
TO: <sip:2138797082;[email protected];user=phone>
CSEQ: 3 SERVICE
CALL-ID: de750f98bdd94e908be5f2f975228ff7
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.0.11:58059;branch=z9hG4bKd47f1d3c
CONTACT: <sip:[email protected];gruu;opaque=srvr:MediationServer:CiGdW3iH5FiI3Qvr3PIKGQAA>
CONTENT-LENGTH: 630
SUPPORTED: gruu-10
USER-AGENT: RTCC/5.0.0.0 MediationServer
CONTENT-TYPE: application/msrtc-reporterror+xml
<?xml version="1.0" encoding="us-ascii"?>
<reportError xmlns="http://schemas.microsoft.com/2006/09/sip/error-reporting">
<error callId="[email protected]" fromUri="sip:3158222726;[email protected];user=phone" toUri="sip:2138797082;[email protected];user=phone" fromTag="ac3201ce-4d7"
toTag="" requestType="INVITE" contentType="application/sdp;call-type=audio" responseCode="400"><diagHeader>10013;reason="Gateway peer in inbound call is not found in topology document or does not depend
on this Mediation Server"</diagHeader><progressReports /></error></reportError>------------EndOfOutgoing SipMessage
Call
Send SMS
Add to Skype
You'll need Skype CreditFree via Skype

@Paul, Thanks for you response.
All ports / IP Add / DNS are defined properly. Telenet on listening port is working.
We are using Public Certificate for 3 Domains (wild card) and same is loaded and verified in SBC
I've not reviewed the OCS logs properly posted above.
What i've found or seems to me is that in a TLS Calls:
After receiving SIP Invite from SBC, mediation server started TLS Negotiation Process b/w Lync 2013 Server Pool and it fails.
SIP Domains:
contoso.com (default)
fabrikam.com
Lync FE Pool (lync.contoso.com
Here are the some more logs.
TL_INFO(TF_PROTOCOL) [0]2DF8.2930::05/01/2014-11:50:31.612.00025e49 (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2716989131]
<<<<<<<<<<<<Incoming SipMessage c=[<SipTlsConnection_103DFE0>], 10.10.0.11:5067<-10.10.7.50:24591
INVITE sip:[email protected]:5067 SIP/2.0
FROM: "3158222726" <sip:[email protected]>;tag=ac3201ce-ae
TO: <sip:[email protected]:5067>
CSEQ: 2 INVITE
CALL-ID: [email protected]
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-010c
CONTACT: <sip:[email protected]:5067;transport=TLS>
CONTENT-LENGTH: 406
SUPPORTED: replaces,update,100rel
USER-AGENT: SONUS SBC1000 3.1.2v293 Sonus SBC
CONTENT-TYPE: application/sdp
ALLOW: INVITE, ACK, CANCEL, BYE, NOTIFY, OPTIONS, REFER, REGISTER, UPDATE, PRACK
P-ASSERTED-IDENTITY: "3158222726" <sip:[email protected]>
v=0
o=SBC 9 1001 IN IP4 10.10.7.50
s=VoipCall
c=IN IP4 10.10.7.50
t=0 0
m=audio 16418 RTP/AVP 8 0 101 13
c=IN IP4 10.10.7.50
a=rtpmap:8 PCMA/8000/1
a=rtpmap:0 PCMU/8000/1
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:13 CN/8000
a=ptime:20
a=tcap:1 RTP/SAVP
a=pcfg:1 t=1
a=crypto:1 AES_CM_128_HMAC_SHA1_80 inline:pqL6Tke8pVmXPuplJ1G3+Sr9jM97H8R7iBagWzzh|2^31|1:1
a=sendrecv
------------EndOfIncoming SipMessage
TL_INFO(TF_PROTOCOL) [1]2DF8.0E04::05/01/2014-11:50:31.665.00025e8e (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2716989131]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_103DFE0>], 10.10.0.11:5067->10.10.7.50:24591
SIP/2.0 100 Trying
FROM: "3158222726"<sip:[email protected]>;tag=ac3201ce-ae
TO: <sip:[email protected]:5067>
CSEQ: 2 INVITE
CALL-ID: [email protected]
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-010c
CONTENT-LENGTH: 0
------------EndOfOutgoing SipMessage
TL_INFO(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.652.00025f32 (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(454))[946832530] $$begin_record
Severity: information
Text: TLS negotiation started
Local-IP: 10.10.0.11:5061
Peer-IP: 10.10.0.11:52529
Connection-ID: 0x10BE00
Transport: TLS
$$end_record
TL_INFO(TF_PROTOCOL) [1]184C.0EFC::05/01/2014-11:50:32.669.00026236 (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[1853494582] $$begin_record
Trace-Correlation-Id: 1853494582
Instance-Id: 425D
Direction: incoming
Peer: 10.10.0.11:52529
Message-Type: request
Start-Line: NEGOTIATE sip:127.0.0.1:5061 SIP/2.0
FROM: <sip:contoso.com>;ms-fe=LYNCFE1.fabrikam.com
TO: <sip:contoso.com>
CALL-ID: aa53739ef9b34b93ba9c97d3ee56cb99
CSEQ: 1 NEGOTIATE
VIA: SIP/2.0/TLS 10.10.0.11:52529
MAX-FORWARDS: 0
CONTENT-LENGTH: 0
SUPPORTED: NewNegotiate
SUPPORTED: ECC
REQUIRE: ms-feature-info
SERVER: RTC/5.0
$$end_record
TL_INFO(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.669.0002636e (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(383))[946832530] $$begin_record
Severity: information
Text: Connection established
Peer-IP: 10.10.0.11:52529
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Peer-Cert: contoso.com(LYNCFE1.fabrikam.com)
Transport: M-TLS
Data: alertable="yes"
$$end_record
TL_WARN(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.669.00026387 (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(386))[946832530] $$begin_record
Severity: warning
Text: The pool FQDN provided by the peer in its NEGOTIATE feature information does not match the pool configured in CMS for the server FQDN that it provided
Peer-IP: 10.10.0.11:52529
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Peer-Cert: contoso.com(LYNCFE1.fabrikam.com)
Transport: M-TLS
Data: fqdn="LYNCFE1.fabrikam.com";pool="contoso.com";expected-fqdn="lync.contoso.com";info="Possible server configuration issue"
$$end_record
TL_INFO(TF_DIAG) [1]184C.0EFC::05/01/2014-11:50:32.670.000265be (SIPStack,SIPAdminLog::WriteDiagnosticEvent:SIPAdminLog.cpp(802))[1853494582] $$begin_record
Severity: information
Text: Routed a locally generated response
SIP-Start-Line: SIP/2.0 200 OK
SIP-Call-ID: aa53739ef9b34b93ba9c97d3ee56cb99
SIP-CSeq: 1 NEGOTIATE
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
$$end_record
TL_INFO(TF_PROTOCOL) [1]184C.0EFC::05/01/2014-11:50:32.670.00026615 (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[1853494582] $$begin_record
Trace-Correlation-Id: 1853494582
Instance-Id: 425E
Direction: outgoing;source="local"
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Message-Type: response
Start-Line: SIP/2.0 200 OK
FROM: <sip:contoso.com>;ms-fe=LYNCFE1.fabrikam.com
To: <sip:contoso.com>;tag=C3A751556F332F7265E9BA2517C878D4
CALL-ID: aa53739ef9b34b93ba9c97d3ee56cb99
CSEQ: 1 NEGOTIATE
Via: SIP/2.0/TLS 10.10.0.11:52529;ms-received-port=52529;ms-received-cid=10BE00
Content-Length: 0
Require: ms-feature-info
Supported: NewNegotiate,OCSNative,ECC,IPv6,TlsRecordSplit
Server: RTC/5.0
$$end_record
TL_INFO(TF_PROTOCOL) [1]2DF8.1078::05/01/2014-11:50:32.671.000266da (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[720988281]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_F8A09B>], 10.10.0.11:52529->10.10.0.11:5061
SERVICE sip:2138797082;[email protected];user=phone SIP/2.0
FROM: <sip:2138797082;[email protected];user=phone>;epid=16FEE4A02E;tag=22fd877f3a
TO: <sip:2138797082;[email protected];user=phone>
CSEQ: 3 SERVICE
CALL-ID: ac0f7bc4cdc94c1dbd0bb51c7c02c890
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.0.11:52529;branch=z9hG4bK67a4c9d1
CONTACT: <sip:[email protected];gruu;opaque=srvr:MediationServer:CiGdW3iH5FiI3Qvr3PIKGQAA>
CONTENT-LENGTH: 628
SUPPORTED: gruu-10
USER-AGENT: RTCC/5.0.0.0 MediationServer
CONTENT-TYPE: application/msrtc-reporterror+xml
- <reportError xmlns="http://schemas.microsoft.com/2006/09/sip/error-reporting">
- <error callId="[email protected]"
fromUri="sip:3158222726;[email protected];user=phone"
toUri="sip:2138797082;[email protected];user=phone"
fromTag="ac3201ce-ae"
toTag=""
requestType="INVITE"
contentType="application/sdp;call-type=audio"
responseCode="400">
<diagHeader>10013;reason="Gateway peer in inbound call is not found in topology document or does not depend on this Mediation Server"</diagHeader>
<progressReports/>
- </error>
------------EndOfOutgoing SipMessage

ACE module, TLS and smtp

Hello,
On a ACE module running software version ACE2(1.0), I have defined a virtual smtp server that is load-balanced to a serverfarm containing 2 SMTP servers. Normal SMTP connexions on port 25 work fine. SMTPS connexions to port 465 of a second vserver also work fine: SSL termination occurs at the ACE module and SMTP connexions to the real servers are in clear text on port 25. But I am having problems with TLS.
If a client connecting to port 25 of the first vserver tries to negotiate TLS, it works but it's the real server that handles TLS encryption. This is normal behavior - but the certificate has to be installed on each of the real servers. I would like the ACE module to handle TLS (it's supported according to the documentation). That way the certificate would only have to be installed on the ACE module.
So I tried to setup a third vserver on port 587 with the same "proxy-service" as the second vserver used for SSL. If a client connects to port 587 of the vserver via TLS, we only see the 3-way handshake between the client and the vserver, then a pause of a few seconds, then a FIN from the client and finally an ACK and a RESET from the vserver.
There are absolutely no lines in the log that could help me find out what's happening.
I found the "debug ssl" command in the documentation but I don't know how to use it - I entered the command and nothing happened; I don't know where the debugging information goes. This is probably why there's a warning that says that "The ACE debug commands are intended for use by trained Cisco personnel only."...
So my questions are: why is TLS not working? How can I find out why it's not working? Where does the "debug" information go when we use the "debug" commands?
Thanks a lot for any help you can give me!
Regards,
Marc.

SMTP over TLS is not supported in ACE currently.
SMTP doesnt use SSL/TLS simply as a secure transport like LDAP, IMAP, POP, HTTP.
In case of SMTP client needs to open a new conn.
So ACE or for that matter any other SMTP relay device needs to terminate conn, look in to the SMTP pkts and punch hole according to the new client conns.
You can get more details at
http://tools.ietf.org/html/rfc2487
Syed

I am having difficulty: we are running a windows server 2003 - mail and outlook support 2007 and upwards, how do I get the brand new apple machines to work with the 2003 version of server

I am having difficulty: we are running a windows server 2003 - mail and outlook support 2007 and upwards, how do I get the brand new apple machines to work with the 2003 version of server

I may be way out, but do you know about this product, would it help integrate the Macs for you.
https://www.thursby.com/sites/default/files/images/ADmitMacv8_SPD.pdf

IMAC's Top graphics card frustration - Cheap and no support for Adobe Mercury Playpack Engine GPU Acceleration?

If anyone has a solution for getting the Mecury Playpack Engine GPU acceleration to work with Premiere Pro CS6 on an iMAC 2011, please let me know. Like I wonder if you could Thunderbolt an External graphics card somehow? Or is an upgrade possible? Ahh...not worth the risk.
Please, if you have a solution for me, let me know. Otherwise I find it pretty frustrating that I purchased a top-end iMAC, fully maxed-out in every way possible, and that the iMac doesn't support Adobe Premiere's Mercury Playback Engine GPU acceleration. Also, an old USB 2.0 Hub and thus the built-in SD card reader is slow. If you have SD cards with 95MB/s Transfer, Read and Write speeds, the iMAC will only transfer at around 30MB/s if you're lucky. Technically 480Mbs which is around 50MB/s but I haven't seen those speeds.
I figured this could at least be circumvented with a Thunderbolt SD card reader or a Thunderbolt to USB 3.0 adapter but of course no such thing exists.
Well, nothing with a reasonable price tag. This all might seem trivial to some but when you're uploading 24 hours of HD video footage from a 128GB SDXC card, the speed makes a big difference.
And come on, no BluRay support? Ridiculous. I get the politics of why but still, just ridiculous. It would be nice to be able to burn a BluRay to watch in my home theater system. There are other methods but BluRay is convenient and great for backing up large Video Files. Unfortunately BluRay looks like it's not going to make it. Maybe cable distribution companies will increase their Internet upload speeds one day and I can just store everything in the cloud and watch full length movies(that I've created) on Vimeo.
Anyways, I went and took a look at the hardware Apple stuffed inside my fancy (3.4 Ghz i7, 16GB 1333 DDR3, 2GB AMD 6970M, 256 GB SSD Internal and 2TB 7200 Internal) machine and it appears to be pretty middle of the range stuff. It's an iMAC, not a Mac Pro so why am I griping? Because my 2009 PC(which I tricked out over the last two years) is faster and does support the Mercury Playback Engine. I spent $2100 total on this PC which includes all my upgrades. I spent around $3300 on the iMAC. I feel ripped off.
Yes, I do love my iMAC on multiple levels but had I known my dated 2009 PC would render video projects faster, I would have gone with a MAC Pro or just a new PC. It seems that Mac is moving completely away from making high-end computers for niche markets(video editing) and focusing on their tiny laptops, IPADS and IPhones for the masses. Obviously smart from a capitalistic perspective(at present at least) but very frustrating for some.
I was actually told to purchase a MAC for video editing. I've been a PC guy for 15 years. I went with the iMAC because I had read many good things about it(probably just Apple propaganda) and also the MAC PRO was to be discontinued. Also the MAC Pro would have been triple the cost for what didn't seem like a whole lot more.
It's one's thing to prepackage a computer with inferior hardware(the iMAC I have is fast for most things and more than enough for 99% of the population) but to not allow us to pop open the computer and make a quit upgrade to the machine is what really makes me feel like I'm using a computer built for Grannies. I mean there is a reason my mother loves iMacs and Iphones. Amazing that I was able to upgrade my memory from 4 to 16GB but I've heard Apple has even done away with that. I get why they do it. Apple Warranty, Apple Care issues, Profit and World Domination: Apple wants a monopoly on everything.
Was great to see Adobe bounce back after the whole Flash/HTML5 thing and knock Final Cut Pro off the face of the Earth for good. People are still buying it b/c of the brand name but Final Cut is done. David Fincher used Adobe's Workflow for everything when he made The Girl with The Dragon Tattoo. Hollywood is making the shift and the world will follow. The Adobe Workflow has finally come together and there is just no way Apple can compete with Adobe Creative Cloud and an Engine that can just swap from Premiere to After Effects to Prelude to SpeedGrade to Photoshop to Story with speed for $29 bucks a month(or $49 for some). Apple better start supporting Adobe's Mercury Engine or they may have a problem. And if you're using Final Cut X, you're severely handicapping yourself. Problem is that people don't want to take the time to learn Adobe's products(steep learning curve for sure) which is where Apple's Granny software, and perhaps computers, comes in to play. Arnold Schwarzenegger once said "Milk is for babies, Real Men Drink Beer". I'm beginning to think that "Mac's are for Grannies, Real Men Use Adobe and PCs".
The major problem with Apple is you're forced to use Apple. Not sure but history has proven that people don't like to be forced into anything. Autocracies don't work. These systems eventually topple, even in the corporate world.
Amazon.com, now that's the company to emulate. What an amazing machine!
I've read that Apple may even discontinue the iMAC after 2013. Who knows?
If anyone has a solution for getting the Mecury Playpack Engine GPU acceleration to work with Premiere Pro CS6 on an iMAC 2011, please let me know. Like I wonder if you could Thunderbolt an External graphics card somehow? Or is an upgrade possible? Ahh...not worth the risk.
1) Graphcis Card - AMD Radeon HD 6970M 2048 MB (6990 would have been better or something from NVIDIA.
2) USB 2.0 Hub with only 480 Mb/sec
3) Seagate Baracude SATA I 7200 RPM drive with 3GB/s transfer rate and only a 32 GB Cach. It's ok. I would have expected at least a Western Digital Caviar Black 2 TB SATA III 7200 RPM 64 MB or the Velociraptor at 10,000RPM.
4)APPLE SSD TS256C Flash Drive. As you can see, it doesn't stack up so well against other SSD Drive.
Just average. http://www.harddrivebenchmark.net/hdd_lookup.phphdd=APPLE+SSD+TS256C

Whining and ranting about how iMacs can't do this or iMacs/orMacs can't do that is not going to get you a lot of help here.
Your "I love my MAC" is typical of the ever ubiquitous PC whiner.
If your video work needs were that computer intensive and critical , you should've done some online research and you should have budgeted for a Mac Pro.
Mac Pros are completely expandable and upgradeable unlike the iMac.
Mac Pros have much more faster and more CPU cores than the iMac line.
iMac line is limited to CPUs with 8 cores. The Mac Pros, I believe, are up to 16 core CPUs, now.
The Mac Pros can have their GPU upgraded and you even add/expand to use specialty audio/video cards.
Mac Pros are the defacto standard for real video work.
iMacs, even the high end model, is not really designed to do really heavy and intensive video work.
iMacs do do video creation and editing. Just not on the level that is needed from a more "Pro" computer.
It seems to me you are asking your iMac to do more than it was originally designed for, in terms of professional video editing.
You get a lot more out of a Mac Pro than an iMac for any real serious video, CGI or animation work.
You just didn't want to spend that much cash on one.
iMacs are not user upgradeable or friendly to user upgrades at all!!!
If you purchased a Mac Pro, you could've had that better, faster HD, better faster SSDs.
That said, I can offer no real help to but because of the nature of your post and the fact you just simply annoyed me, I feel some advice and explanations are in order
First off, you picked Adobe video editing software suite as your video creation software on the Mac. It's no secret to long-time video content creators on the Mac that Adobe products, especially those for video creation and editing are very user unfriendly on the Mac. Even though Macs are supported from Adobe, Adobe for a long time has treated the Mac and Mac users as second class citizens.
Before purchasing and installing Adobe Premiere, did you even check Adobe's site for the preferred system hardware and software requirements? Hmmm?
This is why you should KNOW what software you are going to be running on a computer first then research what computer make and model will run said software.
That's why Apple has its own apps like Aoerture, Logic and Final Cut.
Despite your ignorance in this matter, Final Cut Pro X is alive and doing well, thank you, and using this software on your iMac would kick Adobe Premier in the you know whats.
Final Cut Pro X is a complete video solution for and completely designed around the Mac.
Why are you using USB 2.0 connections for video work when you have a perfectly good FireWire 800 connection.
In case you are not aware, FireWire 800 is called so because it has a max throughput of 800 Mbps.
Your 2011 iMac can take up to 32 GBs of RAM. Not just 16 GBs.
This changed when the 2010 model iMacs came out.
Blu-ray? I believe you can buy external Blu-ray writers that work with Mac using said FW800 connection.
So you cite one movie and one videographer using Adobe Premier for your premise that Final Cut is dead in Hollywood?
Your argument that Apple locks you into everything in their world can be countered by saying Windows and Windows PCs lock you into the Windows world. What's your point?
Apple is not discontinuing their computers platforms any time soon.
All you are regurgitating is rumor. Probably from all of the PC crowd.
iMacs and professional desktop Macs are not going anywhere.
Currently, Apple is the only desktop/laptop computer maker that is still making a profit on their Macs and increasing their market share percentages for the last 5 years during which the PC market has continually slumped/dropped in its market share.

Mp3 and j2me supporting reliance mobile

hi,
if anyone know abt mp3 and j2me supporting Reliance phone in market.if so please give me the link where to get teh details I already checking it with reliance website and i want more information please help me.
thanx in advance
laxmi

hi laxmi
i dont know did you check this URL
www.dadp.com
there is one forum also avail for the j2me and realience phone you will get all the information tehre
regards
[email protected]

Windows Vista 64 Bit and Button Support - Qosmio G30?

Windows Vista 64 Bit and Button Support?

Everybody claiming that Vista x64 (or Ultimate) can't be used with FN keys or Flash Cards is utterly wrong!
I have a Qosmio G30 running Vista x64 Ultimate, and have both FN keys, Toshiba Flash Cards and (partly) the hardware buttons at the top working.
After a lot of research, I found that Toshiba has released a 64-bit version of VAP called util_tvap_27581D. If you google it, you might discover it...

IPAD MINI RETINA SCREEN VERSION IOS 7.1.2 can't success download apps , need to reboot every times only can download apps. Is iOS problem or hardware issue.? Local agent switch sale and tech support can't fix my problem.

I Purchase iPad mini retina screen on July 7 2014 at Malaysia local apple sale agent switch store somehow now my iPad did restore to latest iOS 7.1.2, before that and after also facing 1new issue is my iPad mini cant success download apps and error message show can't download at this time, either retry or click done. My internet is good condition no line down, I reboot my iPad only can download but sometime can't need to reboot twice only can download. Very sad local sale and tech support can't help to solve my problem...

Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, tap Settings > General > Reset > Reset All Settings
If that doesn't help, tap Settings > General > Reset > Reset Network Settings
You will have to re enter your Wi-Fi password.
No data is lost due to a reset.
If nothing above helped, try here > iOS: Troubleshooting Wi-Fi networks and connections

MacBook Crash and Apple Support

Not sure if anyone else has had this experience. First, I am a brand new Mac user. Bought the new MacBook Pro i7 with 8GB of RAM as a switch from my PC laptops.
Any other big crashes out there? Just wondering if there is a systemic hardware issue?
I had the new laptop for a total of 4 days before it crashed hard. on the first full day of use, it started crashing with the veil of grey and the message that a serious error had occurred and I needed to hold down the power button to restart. It crashed a total of 6 times in 4 days (2 days of real use) before I could get to the Genius Bar.
They stated that was obviously not normal and that I should request a new unit from AppleCare, which I did as an advanced replacement. I was hoping to keep my crashing laptop just to get more used to the Mac. However, after the Genius Bar did an archive re-install, the computer immediately crashed twice while in the store.
We then attempted to do an Erase and Install, and the unit would not install the fresh load of Mac OS X. The Genius Bar rep said it definitely looked like a hardware issue since it would not re-install the software, so I had to send the unit back ahead of receiving a replacement.
As for customer service, there was absolutely no urgency to get a replacement laptop to me. It was a customized unit and it is finally due to arrive today, but it has taken 10 days since I ordered my advanced replacement.
I will tell you that this has been a very frustrating and disappointing start to my Mac usage. And customer support could have made that bad experience so much better, but their lack of action and mis-statements actually made it worse.
Sorry, I was hoping for a much better experience. I am still hoping that IF the second MacBook works I can see that I made the right decision.
LewieE

Hi A Brody,
Lemons do happen and while that was a disappointment, the Genius Bar guys did a great job. I will say my expectations were higher for Apple based on everything I heard trying to make my decision to swap from a PC.
The first customer service rep I spoke to when I setup the advanced replacement stated that this unit would be put at the head of the que as it was a replacement for defective unit. The second rep I spoke with said advanced replacements have the lowest priority and it should have been returned as a zero dollar replacement and by him changing it to that, especially since my return unit had been received, would cause it to jump to the head of the shipments. The third person I spoke to said it just had to be processed in the normal 5-7 day shipping replacement and there was nothing they could do.
When a customer has a problem, customer service can make or break that experience. In fact, customers that have had a problem and had a positive resolution to that problem are shown to be more loyal than customers that have never had a problem at all.
Regards,
LewieE

You have to love HP products and their customer service and technical support

My daughter has one of your ZV5000 notebooks. She has been very happy with it until the last few months when she started having charging issues. After investigation I found out that HP had a class action suit over this very problem. I called customer support and I emailed customer support trying to get HP to live up to it's obligation and fix it. I got no where and after several hours I gave up. She decided to get a new notebook. She bought a Compact Presario CQ50-130US from Staples. When she got it home she tried to connect to my wireless router and couldn't. We called technical support and spend the following 2 hours trying to get it to connect. I spoke to several techs none of which knew what they were talking about. They would read step by step from some try this if that doesn't work try this directions they must have. If that wasn't bad enough we constantly had to ask for it to be repeated because we couldn't understand them. They spoke English but with such heavy accents you couldn't understand what they were saying. The last tech was going to call Comcast my internet provider. I told him they provided the internet service not the router. He couldn't understand that. After keeping me on the phone for 15 minutes he came back to say he couldn't get threw and would call me back when he did. There customer service must be as good as yours is to get threw to. I got a call 24hrs later to ask if everything was alright. They never fixed the problem how could it be alright? By then she had decided to return the new one and buy a product other than HP or Compact. I would up fixing her old laptop something HP should have paid for but didn't. I have always trusted and respected the HP name. I am very sorry to see what it has become to stand for. Inferior products that you don't stand behind and customer and technical support that can't speak English and don't have a clue as to what they are doing. How sad! Do you think any of my family or friends will be buying an HP product?

well, this IS a means of finding a resolution for some issues. so why SHOULDNT they read this forum? i can assure you that there are people who are not just reading stuff off a book or a document. in fact, that is the biggest cliche's that exists today.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

Migration and SAP Support for BW 3.1

Hi,
I have couple of queries regarding Migration and SAP Support.
What is the required patch level that need to be mantained in BW 3.1 for a direct upgrade to BI 7.
I would like to know whether SAP still supports BW 3.1. I searched in SAP Service marketplace, but didn't get much information regarding this.
Your inputs are highly appreciated.
Regards,
Hari

Hello,
BW Upgrade from 3.x to 7.0
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/e62b9990-0201-0010-42a7-ddcf5c93cafd
Hope it will help you.
Regards,

Problem with installing Photoshop elements 9 and adobe support advisor

Hi, I've received a graphic tablet with 2 programs: the first has been downloaded and works perfectly while the second, PSE9, has been giving me problems for at least a week!
I downloaded it and now I have a winzip file full of strange things (one of this is set up exe which tells me that I have to install adobe support advisor) and two files which said 3DF.tmp and PSEP9(1).zip.download and if I try to click them they tell me that I have to find on the Net the program to open them because I can't. And I don't know which program is required.
I tried a lot of times to download the adobe support advisor, I have enough space on my disc and my farewall is deactivated, but when the program begins I saw this annoyant message
cpsid_82829s5 Missing installation file bootstrapper error occured
with this code for a support from adobe 00-67325-032018052012
I unistalled it and retried, but nothing.
Please, I just want to use my tablet with the programs which are comprised in the package, why it's so difficult to download this damn photoshop elements 9????????????
Thank you

In the error message it doesn't tell me
"Installer has detected that a machine restart is pending. It is recommended that you quit the installer, restart try again,"
neither "Installer failed to initialize. File not found. Please download Adobe Support Advisor to detect the problem."
and I have enough space and I have Windows xp then I should be able to install it. I tried to unistall and install again the support advisor but nothing. I'm desperate.
Messaggio originale----
Da: [email protected]
Data: 18/05/2012 22.20
A: "Questionlady"<[email protected]>
Ogg: Problem with installing Photoshop elements 9 and adobe support advisor
Re: Problem with installing Photoshop elements 9 and adobe support advisor created by Jeff A Wright in Trial Download & Install FAQ - View the full discussion
Did you try the steps listed in http://helpx.adobe.com/creative-suite/kb/troubleshoot-error-messages-b ootstrapper-cs5.html which was identified by the Adobe Support Advisor? If so can you please list each step and the result of those steps. This will allow us to best advise you on your next steps.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4420419#4420419
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4420419#4420419. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Trial Download & Install FAQ by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

VPLS TLS and EVCS support?

Similar Messages

Maybe you are looking for