VPN between IOS and ASA

Hello my friends,
I have been trying to establish VPN connectivity between IOS cisco router and ASA firewall over the internet - no luck so far. I think I am missing some important bit of the configuration.
Here are my configuration commands:
Router:
crypto isakmp policy 20
encryption 3des
auth pre-share
hash md5
group 2
crypto isakmp key XXX address 103.252.AAA.AAA
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
crypto map MAP 5 ipsec-isakmp
set transform 3DES-MD5
match address VPN
set peer 103.252.AAA.AAA
ip access-list extended VPN
permit ip 10.110.25.0 0.0.0.255 10.10.0.0 0.0.255.255
permit icmp 10.110.25.0 0.0.0.255 10.10.0.0 0.0.255.255
ASA commands:
sysopt connection permit-vpn
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
tunnel-group 203.167.BBB.BBB type ipsec-l2l
tunnel-group 203.167.BBB.BBB ipsec-attributes
pre-shared-key XXX
access-list LIST permit ip 10.10.0.0 255.255.0.0 10.110.25.0 255.255.255.0
access-list LIST permit icmp 10.10.0.0 255.255.0.0 10.110.25.0 255.255.255.0
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
crypto map VPN 10 set transform-set 3DES-MD5
crypto map VPN 10 match address LIST
crypto map VPN 10 set peer 203.167.BBB.BBB
crypto map VPN interface outside
Do you have any idea what is wrong? Thank you a lot in advance.

I managed to get this from the show crypto ipsec sa
     local crypto endpt.: 203.167.BBB.BBB, remote crypto endpt.: 103.252.AAA.AAA
     path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/1
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none
     inbound esp sas:
     inbound ah sas:
     inbound pcp sas:
     outbound esp sas:
     outbound ah sas:
     outbound pcp sas:
     local crypto endpt.: 203.167.BBB.BBB, remote crypto endpt.: 103.252.AAA.AAA
     path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/1
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none
And details from show crypto session detail
Interface: GigabitEthernet0/1
Session status: DOWN
Peer: 103.252.AAA.AAA port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit 1 10.110.25.0/255.255.255.0 10.10.0.0/255.255.0.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0

Similar Messages

Remote site redundancy IPSEC VPN between 2911 and ASA

We already have IPSEC VPN connectivity established between sites but would like to introduce some resilience/redundancy at a remote site.
Site A has an ASA with one internet circuit.
Site B has a Cisco 2911 with one internet circuit and we have established site-to-site IPSEC VPN connectivity between the 2911 and the ASA.
Prior to getting the new internet circuit, Site B had a Cisco 877 with an ADSL line which are still available but aren’t currently in use.
The internet circuit at Site B has dropped a few times recently so we would like to make use of the ADSL circuit (and potentially the 877 router too) as a backup.
What is the best way of achieving this?
We thought about running HSRP between the 877 and 2911 routers at Site B and, in the event of a failure of the router or internet circuit, traffic would failover to the 877 and ADSL.
However, how would Site A detect the failure? Can we simply rely on Dead Peer Detection and list the public IP address of the internet circuit at Site B first with the public IP address used on the ADSL line second in the list on the ASA? What would happen in a failover scenario and, just as important, when service was restored – I’m not sure DPD would handle that aspect correctly?
I’ve read briefly elsewhere that GRE might be best to use in this scenario – but I can’t use GRE on the ASA. I have an L3 switch behind the ASA which I may be able to make use of? But I don’t want to disrupt the existing IPSEC VPN connectivity already established between the ASA and the 2911. Can I keep IPSEC between the ASA and 2911 but then run GRE between the L3 switch and the 2911? If so, how would this best be achieved? And how could I also introduce the 877 and ADSL line into things to achieve the neccessary redundancy?
Any help/advice would be appreciated!

Hello,
I don't think GRE tunnel that you could set up on the switch behind ASA would be really helpfull. Still site-2-site tunnel you want to establish between ASA and some routers, but still it is ASA which needs to make decision about which peer to connect to.
Possible solution would be to do HSRP between both routers on LAN side and with two independent tunnels/crypto maps (one on each of them). On ASA you would need to set up two hosts in set peer. Problem of this solution is that if one router at side B is going to go down and second ADSL line will take over ASA will not do preempt after you main Internet connection is up again. This would happen after ADSL Internet connection will be down.
Solution to that would be to assign two different public IP addressess on two different interfaces of ASA. Then you attach two crypto maps to both interfaces and by using sla monitor (let's say icmp to main router, if it does not respond then you change routing for remote LAN to second interface) you are selecting which crypto map (with one peer this time) should be used.
I hope what I wrote makes some sense.

HT5887 Why doesn't AirDrop work between iOS and OSX?

Apple has almost always never fail to seamlessly integrate its devices, until now? I understand that there is iCloud for content sharing between devices. However, AirDrop was introduced as a simpler way for users to not only share contents between their own devices but as well as other users. I understand that the logic behind AirDrop was practiced by windows users since the creation of modem, though it requires many complex steps and compatibility checks to achieve a simple logic. (and Windows never really bothered with perfecting it over all these years, its improved, still buggy)
My question is, why can't we share contents between iOS and OSX? Everytime I need to transfer some files/content, the quickest way I could think of is to send an email to myself. Just the other day I tried to have my colleague AirDrop a file from his 5S to my MBP. I told him with great confidence that this tech existed long ago, and finally Apple decide to kick some DOS *** and launch a super simple version. And that it should by right work with any device with BT and/or WiFi, but knowing Apple, it would only be for their own products. Not in my wildest dreams it didn't work cross OS.
Forget the embarassment, I want to be pampered by this seamless technology. I want the type of exclusiveness with my fellow family and friends of which majority are Apple lovers. I want to regain the confidence that whenever I step out of my room, whichever device I carry/left out, I can do/resume/engage everything as long as I carry an Apple device.
Music, Videos, E-mails, Docs, Images, iMessages, are all checked. So why not Content Sharing?

We would like to know the answer as much as you would. All you can to direct your questions to the only people who can really answer: http://www.apple.com/feedback/

Is there a difference between ios and ios xe sintaxis?

Hi
I´m looking for command referece to ios xe 3.7, but don´t find nothing, I want to know if there is a difference with show commands between ios and xr
Can someone help me?

I believe all the command structure is identical, or at least mostly, since IOS-XE just pulled out the IOSd software component.

Remote VPN between ASA5505 and Netscreen SSG140

Dears,
I'm trying to set up a VPN between an ASA 5505 and SSG40Juniper and the VPN keep flaping:
Nov 27 04:47:27 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, NP encrypt rule look up for crypto map TEST 1 matching ACL ACL_VPN: returned cs_id=cd2e0998; encrypt_rule=cd39bd50; tunnelFlow_rule=cd488220
Nov 27 04:47:27 [IKEv1]Group = 89.XXX, IP = 89.XXX, Security negotiation complete for LAN-to-LAN Group (89.XXX) Responder, Inbound SPI = 0xb98f5dbe, Outbound SPI = 0xddd1484a
Nov 27 04:47:27 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, IKE got a KEY_ADD msg for SA: SPI = 0xddd1484a
Nov 27 04:47:27 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Pitcher: received KEY_UPDATE, spi 0xb98f5dbe
Nov 27 04:47:27 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Starting P2 rekey timer: 3060 seconds.
Nov 27 04:47:27 [IKEv1]Group = 89.XXX, IP = 89.XXX, PHASE 2 COMPLETED (msgid=f46e307a)
Nov 27 04:47:31 [IKEv1]IKE Receiver: Packet received on 81.1XXX:500 from 89.XXX:500
Nov 27 04:47:31 [IKEv1]Group = 89.XXX, IP = 89.XXX, Duplicate Phase 2 packet detected. Retransmitting last packet.
Nov 27 04:47:31 [IKEv1]Group = 89.XXX, IP = 89.XXX, Responder resending lost, last msg
Nov 27 04:47:31 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Starting P2 rekey timer: 3056 seconds.
Nov 27 04:47:31 [IKEv1]Group = 89.XXX, IP = 89.XXX, PHASE 2 COMPLETED (msgid=f46e307a)
Nov 27 04:47:35 [IKEv1]IKE Receiver: Packet received on 81.XXX:500 from 89.XXX:500
Nov 27 04:47:35 [IKEv1]Group = 89.XXX, IP = 89.XXX, Duplicate Phase 2 packet detected. Retransmitting last packet.
Nov 27 04:47:35 [IKEv1]Group = 89.XXX, IP = 89.XXX, Responder resending lost, last msg
Nov 27 04:47:35 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Starting P2 rekey timer: 3052 seconds.
Nov 27 04:47:35 [IKEv1]Group = 89.XXX, IP = 89.XXX, PHASE 2 COMPLETED (msgid=f46e307a)
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Sending keep-alive of type DPD R-U-THERE (seq number 0x1a4070b7)
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing blank hash payload
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing qm hash payload
Nov 27 04:47:38 [IKEv1]IP = 89.XXX, IKE_DECODE SENDING Message (msgid=8977946c) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 80
Nov 27 04:47:38 [IKEv1]IKE Receiver: Packet received on 81.XXX:500 from 89.XXX:500
Nov 27 04:47:38 [IKEv1]IP = 89.XXX, IKE_DECODE RECEIVED Message (msgid=8e9a1247) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 80
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, processing hash payload
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, processing notify payload
Nov 27 04:47:38 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Received keep-alive of type DPD R-U-THERE-ACK (seq number 0x1a4070b7)
Nov 27 04:47:39 [IKEv1]IKE Receiver: Packet received on 81.XXX:500 from 89.XXX:500
Nov 27 04:47:39 [IKEv1]Group = 89.XXX, IP = 89.XXX, Duplicate Phase 2 packet detected. Retransmitting last packet.
Nov 27 04:47:39 [IKEv1]Group = 89.XXX, IP = 89.XXX, Responder resending lost, last msg
Nov 27 04:47:39 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, Starting P2 rekey timer: 3048 seconds.
Nov 27 04:47:39 [IKEv1]Group = 89.XXX, IP = 89.XXX, PHASE 2 COMPLETED (msgid=f46e307a)
Nov 27 04:47:43 [IKEv1]IKE Receiver: Packet received on 81.XXX:500 from 89.XXX:500
Nov 27 04:47:43 [IKEv1]Group = 89.XXX, IP = 89.XXX, Duplicate Phase 2 packet detected. Retransmitting last packet.
Nov 27 04:47:43 [IKEv1]Group = 89.XXX, IP = 89.XXX, QM FSM error (P2 struct &0xcd58eee8, mess id 0xf46e307a)!
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, IKE QM Responder FSM error history (struct &0xcd58eee8) <state>, <event>: QM_DONE, EV_ERROR-->QM_ACTIVE, EV_RESEND_MSG-->QM_ACTIVE, NullEvent-->QM_ACTIVE, EV_VM_START-->QM_ACTIVE, EV_ACTIVE-->QM_RSND_LST_MSG, EV_RESET_LIFETIME-->QM_RSND_LST_MSG, EV_IS_REKEY_SECS-->QM_RSND_LST_MSG, EV_RESEND_MSG
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, sending delete/delete with reason message
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing blank hash payload
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing IPSec delete payload
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing qm hash payload
Nov 27 04:47:43 [IKEv1]IP = 89.XXX, IKE_DECODE SENDING Message (msgid=57422aa9) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 64
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, IKE Deleting SA: Remote Proxy 172.24.0.0, Local Proxy 10.143.0.0
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, IKE SA MM:08bcc57b rcv'd Terminate: state MM_ACTIVE flags 0x00000042, refcnt 1, tuncnt 0
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, IKE SA MM:08bcc57b terminating: flags 0x01000002, refcnt 0, tuncnt 0
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, sending delete/delete with reason message
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing blank hash payload
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing IKE delete payload
Nov 27 04:47:43 [IKEv1 DEBUG]Group = 89.XXX, IP = 89.XXX, constructing qm hash payload
Nov 27 04:47:43 [IKEv1]IP = 89.XXX, IKE_DECODE SENDING Message (msgid=c364409e) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 76
Nov 27 04:47:43 [IKEv1 DEBUG]Pitcher: received key delete msg, spi 0xb98f5dbe
Nov 27 04:47:43 [IKEv1 DEBUG]Pitcher: received key delete msg, spi 0xb98f5dbe
Nov 27 04:47:43 [IKEv1]Group = 89.XXX, IP = 89.XXX, Session is being torn down. Reason: Lost Service
Nov 27 04:47:43 [IKEv1]Ignoring msg to mark SA with dsID 1658880 dead because SA delete
On the Cisco side
crypto ipsec ikev1 transform-set ESP-3DES-ESP-MD5-HMAC esp-3des esp-md5-hmac
crypto ipsec security-association pmtu-aging infinite
crypto map TEST 1 match address ACL_VPN
crypto map TEST 1 set peer 89.XXX.XXX.XXX
crypto map TEST 1 set ikev1 transform-set ESP-3DES-ESP-MD5-HMAC
crypto map TEST interface outside
crypto ca trustpool policy
no crypto isakmp nat-traversal
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
access-list ACL_VPN extended permit ip 10.143.0.0 255.255.0.0 172.24.0.0 255.255.0.0
On the juniper side:
set ike gateway "TO_XXX_ASA" address 81.XXX.XXX.XXX Main outgoing-interface "ethernet0/2" preshare "XXXXXXX" proposal "pre-g2-3des-md5"
set vpn "DATACENTER_XXX_ASA" proxy-id local-ip 172.24.0.0/16 remote-ip 10.143.0.0/16 "ANY"
set vpn "DATACENTER_XXX_ASA" gateway "TO_XXX_ASA" no-replay tunnel idletime 0 proposal "nopfs-esp-3des-md5"
set vpn "DATACENTER_XXX_ASA" monitor optimized rekey
set vpn "DATACENTER_XXX_ASA" id 0x78 bind interface tunnel.2
set vpn "DATACENTER_XXX_ASA" gateway "TO_XXX_ASA" no-replay tunnel idletime 0 proposal "nopfs-esp-3des-md5"
set vpn "DATACENTER_XXX_ASA" monitor source-interface ethernet0/2 destination-ip 10.143.0.1 optimized rekey
set vpn "DATACENTER_XXX_ASA" id 0x7b bind interface tunnel.2
PFS is disabled.
Any idea why I receive these errors?
Duplicate Phase 2 packet detected. Retransmitting last packet.
QM FSM error (P2 struct &0xcd58eee8, mess id 0xf46e307a)!

Hey,
anybody any idea on this problem? We encountered this problem also.
i can see in ASA log that phase1 is completed.
after that we get the msg for phase2 completed.
but followed with a "responder resending lost, last msg" this 3 times, than a QM FSM error and the tunnel being shut down on our end.
the other side, is getting an active SA, but ofc not working.
any idea?
5 Jan 23 2015 14:59:14 713120 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, PHASE 2 COMPLETED (msgid=440ce73e)
7 Jan 23 2015 14:59:18 713906 IKE Receiver: Packet received on yy.yy.yy.yy:500 from xx.xx.xx.xx:500
5 Jan 23 2015 14:59:18 713201 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, Duplicate Phase 2 packet detected. Retransmitting last packet.
6 Jan 23 2015 14:59:18 713905 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, Responder resending lost, last msg
7 Jan 23 2015 14:59:18 715080 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, Starting P2 rekey timer: 27357 seconds.
5 Jan 23 2015 14:59:18 713120 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, PHASE 2 COMPLETED (msgid=440ce73e)
3x times
3 Jan 23 2015 14:59:30 713902 Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, QM FSM error (P2 struct &0x00007fff2a9921f0, mess id 0x440ce73e)!
with kind regards,
Bernd

Site to site vpn between RV215W and ASA5510

Hello,
We're trying to establish a site to site vpn between a RV215W (firmware version 1.0.0.16) and an ASA5510 (ASA 8.2(3)). The ASA currently has 5 other IPSec VPN tunnels running. It sure does look like I've dotted all my "i's" and crossed all my "t's" with respect to both sides of the tunnel. What I'm seeing from the 5510 is that there is some sort of communication between the two devices but there is no IPSec tunnel established and no traffic is getting beyond either device. It shows the RV215W connected but 0 bytes Tx and 0 bytes Rx.
From the RV215W side of things it shows an IPSec SA not established. The protocol is IKE and the encryption used is 3des. Both sides have the same preshare key and are using the same settings. From each device I can ping the public IP address of the other, but I get no further. I believe I have ACL's set up to allow traffic from both internal networks. (although I may not - I'm hardly a Cisco guru, just fumbling my way through this...)
Any guidance/direction would be greatly appreciated.
Thank you in advance!

Hello,
I have found an article that may provide some assistance with your VPN. It has information on more advanced settings on VPNs for the RV215W. I hope that it may be of some use to you.
Advanced VPN Setup on RV215W
Hope it helps,
Andrew Mayfield

VPN between RV042 and Cisco 2801

HI
Kindly help me out. I'm configuring a p2p vpn between a cisco 2801 with IOS 12.3 and a linksys RV042. I'm getting following error on Linksys and Cisco respectively.
[Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
Dec 19 02:40:42 2011
     VPN Log
    Received informational payload, type NO_PROPOSAL_CHOSEN
dst             src             state               conn-id     slot    status
x.x.x.x       x.x.x.x   MM_NO_STATE          0        0       ACTIVE
Below are my config:
Linksys RV042:
Keying Mode: IKE with Preshared Key
Phase1 DH Group: Group2
Phase1 Encryption: 3DES
Phase1 Authentication: MD5
Phase1 SA Life Time: 28800
Perfect forward secrecy : enabled
Phase2 DH Group: Group2
Phase2 Encryption: 3DES
Phase2 Authentication: MD5
Phase2 SA Life Time: 28800
Preshared Key: xxxxxx
Cisco 2801:
crypto isakmp policy 11
encr 3des
authentication pre-share
group 2
lifetime 28800
crypto isakmp key xxxxxx address xxxxxx
no crypto isakmp ccm
crypto ipsec transform-set STRONGER esp-3des esp-md5-hmac
crypto map myvpn 10 ipsec-isakmp
set peer xxxxxx
set transform-set STRONGER
set pfs group2
match address 103
interface FastEthernet0/0
ip address 10.0.0.56 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no mop enabled
interface FastEthernet0/1
ip address xxxx xxxx
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
crypto map myvpn
ip nat pool branch xxxxxx xxxxx netmask 255.255.255.240
ip nat inside source route-map nonat pool branch overload
access-list 103 permit ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 110 deny   ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 110 permit ip 10.0.0.0 0.0.0.255 any
snmp-server community public RO
route-map nonat permit 10
match ip address 110
Rgards
SAM

Hi,
It looks like you are using the default hash for the crypto isakmp policy and that your connection is failing on the phase 1 negotiation. The default hash on the crypto isakmp policy is sha. On the 2801 try adding hash md5.
crypto isakmp policy 11
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
Let me know if that helps.
Thank you,
Jason NIckle

VPN load balancing and ASA !!!

Hi netpros,
I have a couple of questions about this and hope you might be able to assist me.
1.- Are VPN load balancing and failover (Active/Active) mutually exclusive ..? I mean they can't be used at the same time correct ..?
2.- How does the ASA handle the return traffic from the Internal LAN towards the remote client .. Because the cluster only requires ONE public virtual IP address, which will work for incoming packets .. but what about the return traffic which has knowledge of the DHCP scope's default gateway IP address only .. ? How gets the returned packet redirected from the default gateway IP address to the respective ASA internal IP address .?
3.- VPN load balancing only applies to remote clients using easy VPN technology (easy vpn client, hardware client , pIX using easy vpn client etc ) and does not work with static LAN-LAN tunnel .. correct ..?
Your comments are much appreciated

Hi Gilbert ..
1.- Thanks I wanted to make sure.
2.- I know that .. my question is in regards the return packets .. for example if I have the below IP schema:
ASA1: Public 20.20.20.20
Private 192.168.1.1
ASA2: Public 20.20.20.21
Private 192.168.1.2
Cluster virutal IP: 20.20.20.10
Default gateway for segment 192.168.1.0 is 192.168.1.1
Let's say that a vpn client tries to connect and the cluster instructs the client to connect to ASA2 20.20.20.21. The packets reach the internal server at 192.168.1.100. The internal server then sends the return packets back to the client by forwarding them to its default gateway which is 192.168.1.1 (ASA1). Here is my question .. how does the cluster handles this because the return packet are supposed to be directed to ASA2 192.168.1.2
3.- Any idea about this one ..?
Cheers,

VPN between Mac and Windows? share printer and USB drive

Hey everyone, I'm out at college and have a Windows SP2 desktop set up in my room with the printer and our external hard drive. I travel around campus with my macbook pro (10.5), and it'd be really nice to access the printer and my external hard drive.
Problem is that since its a huge vast network, I think its near impossible to do a direct "IP" connect to it. So the next option is to use a VPN, which I have experience with Windows and Hamachi, but I have no idea how to incorporate a VPN between a mac and a windows computer.
Thanks!

Hi Eric and welcome to Discussions and the Apple world.
Mac OSX can read and write from Windows partitions (like the BootCamp Windows partition you are about to create) when using FAT32 as file system for Windows.
However with FAT32 you are limited to a partition size of 32GB.
Mac OSX can also read from Windows partitions that uses the NTFS file system, but it can not write to them unless you use a third-party helper like either Paragons NTFS for Mac http://www.paragon-software.com/home/ntfs-mac/ or NTFS-3G http://www.ntfs-3g.org/
Windows can not even see or use a Mac OSX partition without additional help by MacDrive http://www.mediafour.com/products/macdrive/
Regards
Stefan

TE tunnel issues between IOS and IOS-XR

Hi Guys
I have a situation. The scenario (see the attached diagram) has to PE01 (IOS) connecting via a port-channel to P01 (IOS-XR), turn P01 connect to PE02 (IOS-XR). So we've configured a pseudowire between PE01 and PE02, this works fine! then we've configured a TE tunnel between PE01 and PE02, but when we chose the TE tunnel as preferred path for the PW, happens the following:
PC-A mac address appears on PE02 mac address table, however PC-B mac address doesn't appears on PE01 mac address table, so there is not connectivity between PC's at all.
It seems like the TE tunnel is causing some issue (thought TE tunnel status is okay at all), and the problem seems to be between PE01 and P01, when we take the TE tunnel from the PW preferred path, everything works fine! I'm not sure if this problem is caused by the port-channel too.
I've been looking for some software bugs in IOS 12.2(33)SRE6 and IOS-XR 4.3.1 but there is not such.
Anyone of you had this problem as well?
Marcelo

Hello.
Did you try ping inside vc between PE devices?
Could you provide relevant configuration from PE1,P,PE2 routers?
And the output you got during troubleshooting?

Syncing photos between ios and Mac

Hi
How to sync photos between Mac and ios .. iPhoto is confusing .. If I create an album on Mac and share it to ios
Through iTunes I won't be able to add or delete photos to it with ios which is strange .. If I use photo stream album
Created on ios I won't be able to add photos for them with my Mac so how to do such a simple task with iPhoto ?

Not sure what you're asking here. The only connection between iphoto for mac and iPhoto for iOS is a name. Other than that they have nothing in common. So, no you can't manage albums created on your Mac with iPhoto for iOS and vice versa.
iPhoto Menu -> Provide iPhoto Feedback
For feature requests.

How do I synch pages files between iOs and mac

I have an iMAC as well as an iPad and iPhone. I recently purchased Pages for both the Mac and iOS and would like to have them all synch'd so that I could sit down in front of any device and have my work show up automatically on all devices. This seems straight up the Apple's alley with the iWork beta site and iCloud. But here's the problem.
Sharing my workfrom my iMac sends the information to th enew iWorks Beta.
When I save my documents in the iOs pages apps it goes to the icloud storage...
So is there a way to get the ipad to save to the iworks site or the iMac to the icloud storage?
Seems so easy so I MUST be missing something.
Thanks!

Actually After posting this (on the right side of the screen) I see that it refernces a discussion entitled" Not quite as advertised? iCloud pages". It explained my issues in depth. Unfortunately, there is nothing to do about it for now. We are all waiting for an update :-(
Thanks for the quick reply!

VPN between WRVS4400N and CISCO 857 router

Hi ALL,
Am trying to VPN the two and have setup the WRVS4400N side using IPSec (seems easy enough). Has anyone any experience on the 857 router side? Would you kindly show how that can be configured? Or just point me to any good source doing it will be good too. Thanks!

ip nat inside source route-map nonat interface FastEthernet0 overload
access-list 110 deny ip 10.20.10.0 0.0.0.255 10.10.10.0 0.0.0.255
access-list 110 permit ip 10.20.10.0 0.0.0.255 any
route-map nonat permit 10
match ip address 110
or better (if you have for example the IP public 1.2.3.5)
ip nat pool 1.2.3.5 1.2.3.5 1.2.3.5 prefix-length 30
ip nat inside source list nat-to-internet pool 1.2.3.5 overload
ip access-list extended nat-to-internet
deny ip 10.20.10.0 0.0.0.255 10.10.10.0 0.0.0.255
permit ip 10.20.10.0 0.0.0.255 any
deny ip any any

VPN for Mac. Want to create VPN between Mac and Windows XP

Hey everyone, I'm looking to try and create a VPN for when I'm in college between my Desktop I'll have in my dorm (running Windows XP) and my Macbook Pro (running Mac 10.5). I have a printer and an external hard drive hooked up to my desktop, and I want to make it so that only I can access it through the VPN.
Is this possible?

Hi soccerdude21490-
+Is this possible?+
Theoretically yes. However, it would be up to the school to allow you access through their network.
The first step would be to contact the school's IT department and ask them if they will allow such a connection, and if so, could they please provide you with the settings (ip address etc.).
Luck-
-DP

WCCP does not work between WSA and ASA

I have configured WCCPv2 between WSA S160 ( 6.3.1-025) and ASA5540 (8.2(1)109).
Everything seems to be OK by "show wccp *" on ASA and showing wccp debugging messages (level 4) on S160. Despite of it, WCCP redirection does not work.
If I use packet-capture I figure out that S160 receives GRE packets with TCP SYN from particular LAN host to WWW sites but S160 does not handle them and does not send anything back to ASA.
It is an Exempt from authentication for this LAN host and in Forward proxy mode everything works well.
I have attached an example of a packet-capture (S160.txt - renamed from .cap) and debugging messages from S160 & "show" from ASA.
Does anybody have any idea what the problem is and how I can resolve it ?

IronPort Support team helped me to find the trouble:
If I wish to handle specific port's (80, 8080, etc.) traffic by the transparent proxy I need to configure this port like a listener for the FORWARD proxy
("Security Services" -> "Proxy Settings" -> "HTTP Ports to Proxy")
The WSA guide doesn't clearly say about it.
So the Discussion can be closed ...

VPN between IOS and ASA

Similar Messages

Maybe you are looking for