VPN Redundancy With Same Peer
I have 1 ISP-A line in SiteA
Peer : 10.10.10.10
I have many S2S Tunnels between my SiteA - RemoteSites, i have redundancy when there is a hardware failure in SiteA, but if the ISP link fails there
there is no backup.
If i take another ISP-B i will get diffrerent IP Adress than ISP-A, but my RemoteSites are not agreening on configuring Second Peer as backup.
So what is the way where the VPN tunnel should work with ISP-B with same Peer(ISP-A:10.10.10.10) if the ISP-A is donw.
Hi,
I see sorry. I haven't read through this article properly so apologies if it doesn't cover what I say it does.
But I believe you can also (again IOS version dependant) track ICMP availability. E.g. can I ping www.cisco.com? If yes its up if not fail over. You can configure timers etc. Obviously this adds a slight overhead in terms of traffic.
http://www.cisco.com/en/US/docs/ios/12_3t/12_3t4/feature/guide/gtfhrp.html
The other way I believe you could go about it is configuring the two routers with IPsec High availability and detect the dead peers with DPD. I don't have any config etc to hand I am afraid but a search on IPsec High Availability may turn something up.
Thanks
Similar Messages
-
Hi, maybe somebody have an idea to set a vpn redundancy when my peer are not able to:
configure 2 public IPs on the same VPN
configure the 2 VPNs with the same local network address
I have 2 internet provider and i want to use a backup in case of primary internet goes down.
thank for your help.
Toni.Hello,
The RV320 has a VPN Backup feature. From the admin guide:
"Tunnel Backup—When DPD determines that the remote peer is unavailable, this feature enables the router to reestablish the VPN tunnel by using either an alternative IP address for the remote peer or an alternative local WAN interface. Check the box to enable this feature and enter the following settings. This feature is available only if Dead Peer Detection is enabled"
http://www.cisco.com/c/dam/en/us/td/docs/routers/csbr/rv320/administration/guide/en/rv32x_ag_en.pdf
Page 90.
Please check this information and let us know if it is what you are looking for. -
How to build 2 L2L vpn tunnels pointing to the same peer.
I have a Cisco ASA 5505 on one side and a VMware device on the remote. I have a vpn tunnel currently. I need to establish a second tunnel to the same peer. Because VMware is used on the remote side they can't have the more than one subnet on the tunnel. I need two internal subnets to communicate to the remote peer. Please help.
Thanks,
KenHi Tzy,
Two tunnels for same traffic on a same device is not possible but you can configure a redundancy for the 2 cellular links for the same traffic.
But if the traffic are different for both the ACLs, the the tunnels should come up but you need to define routes as to which traffic would use what interface.
if there is a def route pointing to interface cell0/0/1 then all traffic will be taken using that interface, and you would then need to define either a static route for access-list 102 or a route-map to direct the traffic to the cell0/0/2 interface.
On the ASA, you just need to configure the settings for a dynamic VPN tunnel.
Hope that helps.
Cheers,
Abhi -
Hi guys,
I'm having trouble connecting my new MacBook Air to Cisco Anytime Connect VPN.
The same configuration works with my iMac, in the same network and same Mac OS Mountain Lion on both computers.
After successfully connecting to VPN after a few seconds it gets disconnected and, what is worse, WIFI is not working any more in my macBook Air, I need to deactivate it and start again.
With iMac with the same settings it doesn't happen.
Any ideas?
Thanks!Did you power cycle the network? That's always the first thing you want to do if a device is "missing" or not connecting to your network correctly.
If you have not already tried this a few times, power down the entire network...all devices, order is not important.
Wait a few minutes and place the MBAir close to the TC
Start the modem first and let it run a few moments by itself. Then start the TC if it is the device connected to the modem and let it run a few moments. Then start each device one at a time the same way. -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew -
ASA 5510 Anyconnect VPN question-"Hairpin" vpn connection on same external interface
I have a Cisco ASA 5510, I want to allow a VPN connection to be established by a client on one of the inside interfaces(10.20.x.x) to be able to go out the single External interface and get authenticated by the ASA to create a VPN tunnel to the other inside interface (10.0.X.X) and access resources on that subnet.
Basically want clients on a WLAN to be able to VPN back in to the LAN with the ASA in the middle to get to company resources,
Is this possible?
Thanks,
TommyWhen we connect any VPN on a device then it is always a TO THE DEVICE connection and I am afraid we can connect only to the local / nearest interface where user is connected in a network with respect to ASA.
I have seen this scenario working though earlier with one of my clients wherein he has configured his DNS server accordingly so that depending upon the source of the DNS request an appropriate IP address was provided for same DNS name. For example if user from IP address range 192.168.0.0 range connects to abc.com then it will get IP address 192.168.1.1 and if a user from range IP address10.0.0.0 connects then it will get 10.1.1.1.
If we configure the same scenario as well then your requirement will be fulfiled with same name however VPN has to be enabled on wireless interface again. If not, then as you have described configuring a new domain name for VPN connection only for wireless users should do the deal.
Regards,
Anuj -
How to create device IDs with same name
i am using SE 3310 and its creating different device ids for each node sharing it . since I will be building a RAC enviornment I need these IDs/name to be same .
for example on one node the lun id is /dev/rdsk/c3t0d0s6 but the same lun id on node 2 is /dev/rdsk/c2t0d0s6.
In past with an old storage array I fixed this issue by creating links in /dev/rdsk for c3t0d0s6 ---> c2t0d0s6.
my question is : is there a way in SE3310 that device ids get created with same name or do i still have to rely on creating these soft links ?
thanks
Note: since i need the answer to this quickly i will wait a while and then post this question in other forums and i will update the question here with the answer .This could be a Solaris (I presumed) O.S. question rather than SE3310 or storage question.
The logical device (/dev/[r]dsk/*) is the work of the O.S. when it first configures the device, in this case the LUN from your SE3310. I can go in depth on how the cX number happens (due to device probe order, driver differences, history of device discovery due to need of persistent device naming, etc...) but ... it's a really long story and is really quite irrelevant and most people should not be interested...
If you have COMPLETELY identical servers, i.e. identical hardware down to specific HBA in specific slot are the same, and if you make sure that luns are presented to all servers exactly the same way, same order, and any changes are seen by all servers in the same sequence, in theory, all /dev/rdsk/* devices will be consistent across servers.
But that's still rather irrelevant. Application that is designed to work in a redundant environment should not be dependent on logical devices like /dev/rdsk being the same.
So ... in effect this is also not a question for the Solaris forum, but rather a question for those familiar with RAC, how to configure such that device access is done "safely" through actually identifying the lun rather than assuming /dev/rdsk are consistent. -
Hello,
I have question regarding N+1 redundancy with 2504-HA WLC.
Can I use 2504-HA unit for H+1 redundancy? SSO is not needed
I have two wireless network:
1. With WLC 5508 with about 40 AP(1262), all them are A regulatory domain
2. With WLC 2504, with about 30 Mesh AP(1552), all of them are E regulatory domain
I plan to use two 2504-HA units for backups, one for network with WLC5508 and second for network with WLC2504.
In case N+1 redundancy is management with Prime mandatory ?Hi,
Better to use same model and same software.
Case1: You have 5508WLC
Solution from my side: You must buy a another WLC with HA SKU license(Zero AP license). This wlc can work as N+1 and AP SSO as well as Client SSO but with higher version of code(7.5 or higher).
Case2: You have 2504 WLC
Solution: You must buy a another 2504 HA WLC: AIR-CT2504-HA-K9, that only supports N+1(No AP SSO and NO Client SSO)
http://www.cisco.com/c/en/us/td/docs/wireless/technology/hi_avail/N1_High_Availability_Deployment_Guide/N1_HA_Overview.html
More info:
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1130-ag-series/qa_c67-714540.pdf
Regards
Dont forget to rate helpful posts -
IPad 2 VPN access with iOS 7.1
I updated one of my iPads to iOS 7.1. The upgrade went smoothly but now when I connect to a VPN service (strongvpn) the performance is terrible and I can no longer stream videos through the VPN. My other iPad which I have not updated yet continues to work fine with the VPN as does my iPhone 4s which has also been updated to 7.1. I have used the ookla speed test and get about a 40Mb/s download speed when not connected to the VPN this drops to under 1Mb/s when I run the test after I connect to the VPN . The other iPad and iPhone get about 12Mb/s download speed via the VPN.
I have tried turning off other features like cellular data, Bluetooth etc but nothing changes. I even went so far as to completely reset the iPad and start from scratch but whatever I try I cannot get any improvement in the download speed when connected through the VPN so streaming video is impossible.
I have been in contact with Strongvpn but they have no idea what is going on. All my other devices continue to perform well - just this iPad since it was updated.
Has anyone else who uses Strongvprn successfully updated their iPad 2 without issue?
Thanks in advance for any tips or feedbackJust got an android tablet for less than $250. Less powerful processor, but what would you know? Runs VPN and the same streaming apps perfectly for some strange reason. Can AirPlay to my Apple TV and use it as a remote for the Apple TV. Internet works faster than my iPad 4 too. I wasn't going to wait months for an update/fix with not new functionality and only minor aesthetic differences (plus iOS in the car!).
Hasn't crashed once in 2 days. Haven't been able to say that about my iPad in nearly 6 months.
Good luck guys!
2 mac book airs, 2 iPhones, 2 apple TVs, 2 iPads, Mac, TimeCapsule and bunch of crappy cables that break every six months. Let's see how the software updates go for those. -
Release Strategy - Object "ZX NX" already classified with same characterist
Hi Gurus
While modifiying the exist release strategy the following error occurs.
Object "ZX NX" already classified with same characteristic values
Message no. C1818
Diagnosis
Object ZX NX was already classified with the same characteristic values. In class maintenance, you define whether a warning message or error message is displayed in these circumstances. This message draws your attention to the possibility of data redundancy.
Procedure
Change the assigned characteristic values, so that you do not have redundancy in your system.
Perhaps the object you are classifying is not necessary, because it can be replaced by the object found by the system.
Please advice on this.
Thanks in advance
ARASHi
Thanks for your input. I will test this and come back.
Experts, any further inputs...
Regards
Aras -
Can I use both newly cloned MBPR retina and old-MBP with same Time Machine
When my new-MBPR retina cloned from the old-MBP back up in Time Machine via migration assistance, will this newly-cloned MBPR continue thereon backing up with the same old-MBP back up in Time Machine? I.e. continuing same timeline?
And what happen to my old-MBP back up, if I continuing to use my old-MBP with the same Time Machine on? Will TM recognised 2 different MBP and thus creating 2 back ups? I seem to have problem to keep 2 MBP running with same TM. Programs not responding even force quitting them!
And what should I do to use both? Appreciate your help. Thank you.OK, but in general I can use this one device as both file storage and Time Machine.
I thought that (for some reason) once I set up the Time Capsule to act just as Time Machine storage I would be unable to access it as a plain file storage.
I have just tested it now, and it seems it can work as both - file storage and Time Machine. I can see the Time Machine backup file on it and folders where I can dump regular files.
The only thing I would need to occasionally do is delete some old backups to keep Time Machine segment below 1 TB just so I have plenty of space for regular files.
This thing is awesome. :) -
While send/receive email, I have received an error message "Sending of password d"?
However with same login details, I am able to login with other application.
I have changed password still the issue remains as it is.https://support.mozilla.org/en-US/kb/cannot-send-messages
-
ASA , Cisco VPN client with RADIUS authentication
Hi,
I have configured ASA for Cisco VPN client with RADIUS authentication using Windows 2003 IAS.
All seems to be working I get connected and authenticated. However even I use user name and password from Active Directory when connecting with Cisco VPN client I still have to provide these credentials once again when accessing domain resources.
Should it work like this? Would it be possible to configure ASA/IAS/VPN client in such a way so I enter user name/password just once when connecting and getting access to domain resources straight away?
Thank you.
Kind regards,
AlexHi Alex,
It is working as it should.
You can enable the vpn client to start vpn before logon. That way you login to vpn and then logon to the domain. However, you are still entering credentials twice ( vpn and domain) but you have access to domain resources and profiles.
thanks
John -
Mavericks VPN dropouts with native VPN client and Cisco IPSec
Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions? -
Is there an issue with the hitachi hard drives in the MacBook Pro's ? Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue. Other drive I have had have lasted at least 5 or more years.
there is a dylib you can put in the springboard if jailbroken but if not you have to find an apple store
Maybe you are looking for
-
BI Apps - Financial Analytics (DB connection DAC and Informatica Designer)
Hi all, With correct Physical data sources configured in DAC including production JDE database (Oracle) and Datawarehouse, the ETL process can be finished in DAC without error. However, the datawarehouse tables do not contain any records after the ET
-
Why can I not create a PDF from a web page on my Adobe Acrobat 8 Pro on my new Windows 8 computer? It worked fine on my windows XP system?
-
How do I burn an audio book to cd
I just bought a 16 hour audio book that was downloaded in seven parts. When I went to burn it on CD, the error message came back to break down the playlist into tracts that fit the disc size. Problem is that there is no tracts. I bought the audio boo
-
Is it poss to capture a recorded meeting?
We have Connect v6, and for promo purposes we'd like to put a short clip from a recorded meeting into a PowerPoint presentation which will be running autonomously. I can't see a way to download the recorded meeting (which I presume is a Flash video f
-
Indesign spot colour gradient??
Hi everyone, I have setup a document with a spot gold 872c and would like to use this as a gradient from solid 872 to a tint of 872 back to a solid 872. How is this done? I have greated the spots and included them on a grad but cant change the centre