VPN with Dynamic IP

Hi
I got One HQ and 3 Remote Offices ; all branches would need to access application,Email from HQ.
At HQ I got 3845 VPN Server ; 2MB Internet Link with 2 Public IP
AT Branch #1 I got 2801 Router ; 1MB Internet link with 2 Public IP
At Branch #2 I got 887 DSL Router ; 4MB DSL Internet with Dynamic Public Ip
At Branch #3 I got ASA 5510 ; 1MB DSL Internet with 2 Public IP
Site to Site VPN between HQ and Branch# 1 is working ok. What configuration I need on HQ and Branch #2 to setup the VPN
HQ Subnets
192.168.150.0 255.255.255.0 - Users
192.168.151.0 255.255.255.0 - Application Server
192.168.152.0 255.255.255.0 - Windows Server
192.168.153.0 255.255.255.0 - Linux Server
Branch#1 Subnet
192.168.200.0 255.255.255.0 - Users
Branch#2 subnet
192.168.203.0 255.255.255.0 - Users
Branch#3 Subnets
192.168.206.0 255.255.255.0 - Users
HQ_VPN_Configuration
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
crypto isakmp key 123456 address 5.5.5.5
crypto ipsec transform-set VPN_Con_BR1 esp-3des esp-md5-hmac
crypto map VPN 10 ipsec-isakmp
set peer 5.5.5.5
set transform-set VPN_Con_BR1
match address BR1
Interface tunnel 15
description GRE_Tunel_to_BR1
ip address 10.100.200.1 255.255.255.252
Tunnel source 10.10.12.2
Tunnel destination 172.16.32.2
Interface GigabitEthernet0/0
Description "Connected to BackBone"
ip address 10.10.12.2 255.255.255.248
Interface GigabitEthernet0/1
Description "Public IP Interface"
ip address 1.1.1.1 255.255.255.252
no ip redirect
crypto map VPN
Router ospf 2
network 10.10.12.2 0.0.0.0 area 0
network 10.100.200.1 0.0.0.0 area 0
ip router 0.0.0.0 0.0.0.0 1.1.1.1
ip access-list extended BR1
permit gre host 1.1.1.1 host 5.5.5.5

Looking for support on configuring HQ Router for VPN with Dynamic IP on remote end
I managed to built up Branch#2 configuration
crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key 123456 address 1.1.1.1
crypto isakmp keepalive 300
crypto ipsec transform-set VPN esp-des esp-md5-hmac
crypto map vpn 10 ipsec-isakmp
set peer 1.1.1.1
set transform-set VPN
match address 115
interface Ethernet0
ip address 192.168.203 255.255.255.0
ip nat inside
interface ATM0
bandwidth 4160
no ip address
load-interval 30
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/50
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer0
bandwidth 4160
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip mroute-cache
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap callin
ppp chap refuse
ppp pap sent-username ABCD password 7 ABCD
ppp ipcp address accept
crypto map VPN
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
access-list 100 deny   ip 192.168.203.0 0.0.0.255 192.168.151.0 0.0.0.255
access-list 100 deny   ip 192.168.203.0 0.0.0.255 192.168.152.0 0.0.0.255
access-list 100 deny   ip 192.168.203.0 0.0.0.255 192.168.153.0 0.0.0.255
access-list 115 Permit ip 192.168.203.0 0.0.0.255 192.168.151.0 0.0.0.255
access-list 115 Permit ip 192.168.203.0 0.0.0.255 192.168.152.0 0.0.0.255
access-list 115 Permit ip 192.168.203.0 0.0.0.255 192.168.153.0 0.0.0.255
dialer-list 1 protocol ip permit

Similar Messages

VPN with dynamic ip fail

i have a 2 routers VPN RV042 with 1 tunnel VPN configured, in 1 side i have fixed ip and in other side i have the VPN configured with dynamic dns, when the ip is refreshed by operator (NET) the router stops responding and it chashes being necessary do a restart to come back to work.
I saw that this happens when the ip is updated by the operator. I do the update to last version of firmware but the problem continues. Someone know say how fix this?

Hi
It seems the keep alives are disabled which are necessary to detect peer failure and re initiate the tunnel, could you please enable them and test
~ Harry
*rate helpful posts *
Sent from Cisco Technical Support Android App

Setting up a PIX-PIX VPN with Dynamic and Static IP's

Hey everyone..
I'm recently working to deploy two PIx-506E devices at a remote site and at my home.
I want to be able to connect these together and eventually create a spoke and hub method of deployment to keep several of the places I manage separate but accessible.
The only problem is almost every example I've seem has two static WAN IP's. I cannot have a static WAN at my home, but it will be available for every remote.
How could I go about this? Any articles you can shoot my way and modify so it would work will help me.
Thank you.
Michael Jankowski
Computer Systems Consultant

Hi
In addition to what has been said.
If you are looking to set up site to site VPN's and you don't have a static IP at youe home you can use dynamic crypto maps which allow you to use dynamic ip addressing. You can mix and match so you can use a fixed ip for your remote site and a dynamic ip at home. Attached is a link which explains dynamic crypto maps
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080093f86.shtml
HTH

Wwan 3G/4G 4G LTE HWIC VPN (with dynamic ip)Configuration assistance to multi context asa

Hello All
I have a customer that has several sites all over the world and they want to use 3G and possibly 4G (where available) as a backup vpn solution.
I need some assistance/ guidance in configuring the cellular radio and configuring the vpn (dynamic ip)to work over the wwan.
Countries involved are France, Spain, Australia, Thailand and Malaysia.
I understand that I will need the APN credentials from the service provider. Is this normally the same for 3g and 4g?
Do I get chat scripts from them too?
My vpn gateway in the HQ is a Cisco multi-context asa so I can't configure remote access as its not supported yet. Can I possibly use the 1921 router(4lte hwic installed) at the sites as a hardware client?
I have seen the following urls. One has the 3g router as a "remote access" vpn but I guess this won't work in my scenario.
The other is between ios router and asa which I think will work. I don't need nat on the 3g/4g router as all traffic will be using the vpn.
http://www.networking-forum.com/blog/?p=708 . Will I need this for all the sub-interfaces I configure on the router
interface Vlan1
description LAN
ip address 10.0.0.14 255.255.255.240
no ip redirects
no ip proxy-arp
ip tcp adjust-mss 1452
crypto ipsec client ezvpn ASA inside <--is this needed per interface????
Remote access reference in config:
group-policy 3GPolicy attributes
vpn-tunnel-protocol IPSec
password-storage enable
nem enable
tunnel-group 3GRAGroup type remote-access <---Remote access config
tunnel-group 3GRAGroup general-attributes
authorization-server-group LOCAL
default-group-policy 3GPolicy
tunnel-group 3GRAGroup ipsec-attributes
pre-shared-key **Same key as the ASA profile on the 881**
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/112075-dynamic-ipsec-asa-router-ccp.html
Anyone got a helpful configuration and guide?
Thanks
Feisal

Wwan 3G/4G 4G LTE HWIC VPN (with dynamic ip)Configuration assistance

Hello All
I have a customer that has several sites all over the world and they want to use 3G and possibly 4G (where available) as a backup vpn solution.
I need some assistance/ guidance in configuring the cellular radio and configuring the vpn (dynamic ip)to work over the wwan.
Countries involved are France, Spain, Australia, Thailand and Malaysia.
I understand that I will need the APN credentials from the service provider. Is this normally the same for 3g and 4g?
Do I get chat scripts from them to?
My vpn gateway in the HQ is a Cisco multi-context asa so I can't configure remote access. Can I possibly use the 1921 as a hardware client?
I have seen the following urls. One has the 3g router as a remote access vpn but I guess this won't work in my scenario.
The other is between ios router and asa which I think will work. I don't need nat on the 3g/4g router but will I need
http://www.networking-forum.com/blog/?p=708 . Will I need this for all the sub-interfaces I configure on the router
interface Vlan1
description LAN
ip address 10.0.0.14 255.255.255.240
no ip redirects
no ip proxy-arp
ip tcp adjust-mss 1452
crypto ipsec client ezvpn ASA inside
Remote access reference in config:
group-policy 3GPolicy attributes
vpn-tunnel-protocol IPSec
password-storage enable
nem enable
tunnel-group 3GRAGroup type remote-access
tunnel-group 3GRAGroup general-attributes
authorization-server-group LOCAL
default-group-policy 3GPolicy
tunnel-group 3GRAGroup ipsec-attributes
pre-shared-key **Same key as the ASA profile on the 881**
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/112075-dynamic-ipsec-asa-router-ccp.html
Anyone got a helpful configuration and guide?
Thanks
Feisal

Duplicate post.
Go here: https://supportforums.cisco.com/discussion/12226676/i-want-connect-my-cisco-hq-router-remote-1841-router-using-hwic-3g-gsm-card-and

ASA 5505 VPN with backup route

We are looking to set up a site-to-site VPN with a backup over a T1. We have a remote site with a 1841 router. This router has a PTP T1 back to a secondary location with a 2811. Due to location, the only option we had to get additional bandwidth was to have a cable modem installed. We want to set a site-to-site up to our primary location, with a backup route over the T1 in the event the cable modem goes down. We have an ASA 5505 at the remote location, and an ASA 5540 at the primary. In addition, we want to split the traffic across the two connections. Since the wireless controllers are anchored back to the secondary location, we want to send that traffic over the PTP T1 and the rest of the traffic over the VPN. We also need to have a backup route for the wireless traffic to send across the VPN in the event the T1 goes down.

Go to this link and scroll down to Site to Site VPN (L2L) with IOS and Site to Site VPN (L2L) with ASA, you can use the links example depicting your scenario requirements, where one end is dynamic and other static for Ipsec L2L IOS-to-ASA or ASA-to-IOS.
The best solution obiosly is having static IP addressing, make that clear with your client , but these exmaples are very good solution for your problem.
Keep in mind that the DHCP dynamic side will always be the initiator to bring up the tunnel , not the static side.
http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
Regards

Azure Site to Site VPN with Cisco ASA 5505

I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
(Does azure support 9.x version of asa?)
How can i fix it?

Hi,
As of now, we do not have any scripts for Cisco ASA 9x series.
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
Did you download the VPN configuration file from the dashboard and copy the content of the configuration
file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
According to the
Cisco ASA template, it should be similar to this:
access-list <RP_AccessList>
extended permit ip object-group
<RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
nat (inside,outside) source static <RP_OnPremiseNetwork>
<RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
<RP_AzureNetwork>
Based on my experience, to establish
IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
compatible for dynamic routing, please make sure that you chose the static routing.
Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
Hope this helps you.
Girish Prajwal

Remote access VPN with ASA 5510 using DHCP server

Hi,
Can someone please share your knowledge to help me find why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
ASA Version 8.2(5)
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.6.0.12 255.255.254.0
ip local pool testpool 10.6.240.150-10.6.240.159 mask 255.255.248.0 !(worked with this)
route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
crypto ipsec transform-set FirstSet esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface inside
crypto isakmp enable inside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
vpn-addr-assign aaa
vpn-addr-assign dhcp
group-policy testgroup internal
group-policy testgroup attributes
dhcp-network-scope 10.6.192.1
ipsec-udp enable
ipsec-udp-port 10000
username testlay password *********** encrypted
tunnel-group testgroup type remote-access
tunnel-group testgroup general-attributes
default-group-policy testgroup
dhcp-server 10.6.20.3
tunnel-group testgroup ipsec-attributes
pre-shared-key *****
I got following output when I test connect to ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDO
4024 bytesR copied in 3.41 0 secs (1341 by(tes/sec)13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ISA_KE payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received DPD VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode:        True Aggressive Mode: False
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received NAT-Traversal ver 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, Connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing IKE SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA Proposal # 1, Transform # 9 acceptable Matches global IKE entry # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ISAKMP SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for Responder...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Cisco Unity VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing xauth V6 VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Traversal VID ver 02 payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Fragmentation VID + extended capabilities payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + HASH (8) + NOTIFY (11) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing IOS/PIX Vendor ID payload (version: 1.0.0, capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
kens-mgmt-012# P = 10.15.200.108, Automatic NAT Detection Status:     Remote end is NOT behind a NAT device     This   end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing MODE_CFG Reply attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: IP Compression = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling Policy = Disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Setting = no-modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Bypass Local = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, User (testlay) authenticated.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg ACK attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=49ae1bb8) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg Request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 net mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DNS server address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for WINS server address!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Received unsupported transaction mode attribute: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Save PW setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Default Domain Name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split Tunnel List!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Browser Proxy Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for backup ip-sec peer list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Smartcard Removal Disconnect Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Application Version!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Client Type: WinNT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DHCP hostname for DDNS is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=b04e830f) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE received response of type [] to a request from the IP address utility
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Cannot obtain an IP address for remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE TM V6 FSM error history (struct &0xd8030048) <state>, <event>: TM_DONE, EV_ERROR-->TM_BLD_REPLY, EV_IP_FAIL-->TM_BLD_REPLY, NullEvent-->TM_BLD_REPLY, EV_GET_IP-->TM_BLD_REPLY, EV_NEED_IP-->TM_WAIT_REQ, EV_PROC_MSG-->TM_WAIT_REQ, EV_HASH_OK-->TM_WAIT_REQ, NullEvent
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE AM Responder FSM error history (struct &0xd82b6740) <state>, <event>: AM_DONE, EV_ERROR-->AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL-->AM_TM_INIT_MODECFG_V6H, NullEvent-->AM_TM_INIT_MODECFG, EV_WAIT-->AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG-->AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK-->AM_TM_INIT_XAUTH_V6H, NullEvent-->AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b terminating: flags 0x0945c001, refcnt 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending delete/delete with reason message
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing IKE delete payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=9de30522) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
Regards,
Lay

For RADIUS you need a aaa-server-definition:
aaa-server NPS-RADIUS protocol radius
aaa-server NPS-RADIUS (inside) host 10.10.18.12
key *****
authentication-port 1812
accounting-port 1813
and tell your tunnel-group to ask that server:
tunnel-group VPN general-attributes
authentication-server-group NPS-RADIUS LOCAL
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Need help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 8.2(1)

Need urgent help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IPSec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make tradiotional Hairpinng model work in this scenario.
I followed every possible sugestions made in this regard in many Discussion Topics but still no luck. Can someone please help me out here???
Following is the Running-Conf with Normal Client to Site IPSec VPN configured with No internat Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel
ASA Version 8.2(1)
hostname ciscoasa
domain-name cisco.campus.com
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
interface GigabitEthernet0/0
nameif internet1-outside
security-level 0
ip address 1.1.1.1 255.255.255.240
interface GigabitEthernet0/1
nameif internet2-outside
security-level 0
ip address 2.2.2.2 255.255.255.224
interface GigabitEthernet0/2
nameif dmz-interface
security-level 0
ip address 10.0.1.1 255.255.255.0
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
ip address 172.16.0.1 255.255.0.0
interface Management0/0
nameif CSC-MGMT
security-level 100
ip address 10.0.0.4 255.255.255.0
boot system disk0:/asa821-k8.bin
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.campus.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network cmps-lan
object-group network csc-ip
object-group network www-inside
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
object-group service udp-port
object-group service ftp
object-group service ftp-data
object-group network csc1-ip
object-group service all-tcp-udp
access-list INTERNET1-IN extended permit ip host 1.2.2.2 host 2.2.2.3
access-list CSC-OUT extended permit ip host 10.0.0.5 any
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq www
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq https
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ssh
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ftp
access-list CAMPUS-LAN extended permit udp 172.16.0.0 255.255.0.0 any eq domain
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq smtp
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq pop3
access-list CAMPUS-LAN extended permit ip any any
access-list csc-acl remark scan web and mail traffic
access-list csc-acl extended permit tcp any any eq smtp
access-list csc-acl extended permit tcp any any eq pop3
access-list csc-acl remark scan web and mail traffic
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 993
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq imap4
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 465
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq www
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq https
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq smtp
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq pop3
access-list INTERNET2-IN extended permit ip any host 1.1.1.2
access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0
access-list DNS-inspect extended permit tcp any any eq domain
access-list DNS-inspect extended permit udp any any eq domain
access-list capin extended permit ip host 172.16.1.234 any
access-list capin extended permit ip host 172.16.1.52 any
access-list capin extended permit ip any host 172.16.1.52
access-list capin extended permit ip host 172.16.0.82 host 172.16.0.61
access-list capin extended permit ip host 172.16.0.61 host 172.16.0.82
access-list capout extended permit ip host 2.2.2.2 any
access-list capout extended permit ip any host 2.2.2.2
access-list campus-lan_nat0_outbound extended permit ip 172.16.0.0 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu internet1-outside 1500
mtu internet2-outside 1500
mtu dmz-interface 1500
mtu campus-lan 1500
mtu CSC-MGMT 1500
ip local pool vpnpool1 192.168.150.2-192.168.150.250 mask 255.255.255.0
ip verify reverse-path interface internet2-outside
ip verify reverse-path interface dmz-interface
ip verify reverse-path interface campus-lan
ip verify reverse-path interface CSC-MGMT
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (internet1-outside) 1 interface
global (internet2-outside) 1 interface
nat (campus-lan) 0 access-list campus-lan_nat0_outbound
nat (campus-lan) 1 0.0.0.0 0.0.0.0
nat (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT,internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
access-group INTERNET2-IN in interface internet1-outside
access-group INTERNET1-IN in interface internet2-outside
access-group CAMPUS-LAN in interface campus-lan
access-group CSC-OUT in interface CSC-MGMT
route internet2-outside 0.0.0.0 0.0.0.0 2.2.2.5 1
route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
http 1.2.2.2 255.255.255.255 internet2-outside
http 1.2.2.2 255.255.255.255 internet1-outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet2-outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map internet2-outside_map interface internet2-outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
        a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as
quit
crypto isakmp enable internet2-outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash md5
group 2
lifetime 86400
telnet 10.0.0.2 255.255.255.255 CSC-MGMT
telnet 10.0.0.8 255.255.255.255 CSC-MGMT
telnet timeout 5
ssh 1.2.3.3 255.255.255.240 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet2-outside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPN_TG_1 internal
group-policy VPN_TG_1 attributes
vpn-tunnel-protocol IPSec
username ssochelpdesk password xxxxxxxxxxxxxx encrypted privilege 15
username administrator password xxxxxxxxxxxxxx encrypted privilege 15
username vpnuser1 password xxxxxxxxxxxxxx encrypted privilege 0
username vpnuser1 attributes
vpn-group-policy VPN_TG_1
tunnel-group VPN_TG_1 type remote-access
tunnel-group VPN_TG_1 general-attributes
address-pool vpnpool1
default-group-policy VPN_TG_1
tunnel-group VPN_TG_1 ipsec-attributes
pre-shared-key *
class-map cmap-DNS
match access-list DNS-inspect
class-map csc-class
match access-list csc-acl
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class csc-class
csc fail-open
class cmap-DNS
inspect dns preset_dns_map
service-policy global_policy global
prompt hostname context
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
Please tell what needs to be done here, to hairpin all the traffic to internet comming from VPN Clients.
That is I need clients conected via VPN tunnel, when connected to internet, should have their IP's NAT'ted against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16)
I'm not much conversant with everything involved in here, therefore please be elaborative in your replies. Please let me know if you need any more information regarding this setup to answer my query.
Thanks & Regards
maxs

Hi Jouni,
Thanks again for your help, got it working. Actually the problem was ASA needed some time after configuring to work properly ( ?????? ). I configured and tested several times within a short period, during the day and was not working initially, GUI packet tracer was showing some problems (IPSEC Spoof detected) and also there was this left out dns. Its working fine now.
But my problem is not solved fully here.
Does hairpinning model allow access to the campus LAN behind ASA also?. Coz the setup is working now as i needed, and I can access Internet with the NAT'ed ip address (outside-interface). So far so good. But now I cannot access the Campus LAN behind the asa.
Here the packet tracer output for the traffic:
packet-tracer output
asa# packet-tracer input internet2-outside tcp 192.168.150.1 56482 172.16.1.249 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   172.16.0.0      255.255.0.0     campus-lan
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   192.168.150.1   255.255.255.255 internet2-outside
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group internnet1-in in interface internet2-outside
access-list internnet1-in extended permit ip 192.168.150.0 255.255.255.0 any
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype:
Result: DROP
Config:
nat (internet2-outside) 1 192.168.150.0 255.255.255.0
match ip internet2-outside 192.168.150.0 255.255.255.0 campus-lan any
    dynamic translation to pool 1 (No matching global)
    translate_hits = 14, untranslate_hits = 0
Additional Information:
Result:
input-interface: internet2-outside
input-status: up
input-line-status: up
output-interface: internet2-outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
The problem here as you can see is the Rule for dynamic nat that I added to make hairpin work at first place
dynamic nat
asa(config)#nat (internet2-outside) 1 192.168.150.0 255.255.255.0
Is it possible to access both
1)LAN behind ASA
2)INTERNET via HAIRPINNING
simultaneously via a single tunnel-group?
If it can be done, how do I do it. What changes do I need to make here to get simultaneous access to my LAN also?
Thanks & Regards
Abhijit

Router PPTP with Dynamic IP

Greetings ... I have a VPN connection and I don't have Static IP Address, Subnet Mask and Gateway is dynamic too
Is LinSys Have WireLess Router with supporting PPTP connection with Dynamic IP?
Example: http://support.dlink.com/emulators/di824vup/prim_pptp.htm

well...u can go for wrv54g...i think this should suffice your requirement...

Setting up VPN with OS X Server/Netgear FVS318 and remote offices

I am a newbie to VPN and am hoping someone can help get the config right. We have an Xserve (Server 10.4) and a range of G5's (OS 10.4) in 3 remote offices and want to setup a VPN between the remote offices back to the xServe. All 3 remote office are behind their own WGT624 router. Our setup looking like this:
Remote Office G5 (OS 10.4)
|
|
Netgear WGT624 (with dynamic IP address supplied by ISP)
|
|
Cable Modem
|
|
**INTERNET**
|
|
Cable Modem
|
|
Netgear FVS318 (v1) with static IP of 61.xxx.xxx.xxx
|
|
xServe (OS X 10.4 Server)
Can someone please walk me through the setup we need at head office and how we setup the branch office.
Thanks

Hi,
1701
UDP
L2TP
l2f
Mac OS X Server VPN service
1723
TCP
PPTP
pptp
Mac OS X Server VPN service
Try L2TP

I am trying to setup VPN with QuickVPN

Hi I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem. So hopefully someone can tell what the problem is or at least point to right direction on solving this.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly..
It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error...
Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options.
I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
Don't know yet whats going on if I am missing something or if there is some problem that needs work-around but if you know the answer or guesses of answer please let me know.

Hi Aleksandr,
since this question is about a product in the Cisco Small Business / Linksys range, I suggest you move it to the community, where you will have a better chance of getting expert advice.
best regards,
Herbert
Cisco Moderator

Xcelsius Engage: Issue with dynamic visibilty of data in dashboard

Hi,
We have a requirement for a dashboard where data for 5 Sites need to be displayed as per 17 KPIs and 12 different rolling months.
Raw sample data looks like below-
SITE KPI        ActYTD Act(Pre Month) PlanYTD Plan(Prev Month) VarianceYTD Variance(Pre Month)
A       On-Time   76.7         82.92                  111.50       109.50             -1                    -1
B       Delay       73.70       80.00                   79.75        77.75             -1                     1
There are 5 different Sites and 17 different KPIs.
Based on the raw data that we get from BI (7.0 query output), we manipulate it in MS excel, using some lookups and formulae to obtain certain values, store them in designated sheets and then Xcelsius (different components) use these sheets as source.
We are having three levels of navigation-
1. Main screen listing all KPIs site wise and months ( the site and months could be selected from Combo boxes at the top). The KPIs are bind to a list view, each row is a selectable KPI leading to level two navigation.
2. Level two contains the details for each KPI ( values and trend chart). Selection in the chart for a Site leads to level 3 navigation.
3. Level 3 screen contains data by KPI and by Site for 12 rolling months ( The sites could be changed from a drop-down).
There are custom navigation buttons (home/back) to enable navigations between the screens.
We are using 3 panel containers, 2 list views, 4-5 combo boxes and some hidden button ( with dynamic visibilty).
The workbook has 8-9 different sheets, though the Xcelsius componets are bound to only 3 sheets.
Things work fine till we select 14th KPI , but Xcelsius starts behaving awkwardly when we select 15th KPI and further.For the selected KPI, the level two screen would load for a flash of a second and then the control comes back to level 1 screen. We do not face this issue till 14th KPI.
In-order to eliminate possibiltes we did the following-
1. Changed the order of KPIs - issue persists
2. Changed the Excel option " Max. no of Rows" to 4000- issue persists
3. Decreased the amount of data to be loaded - issue persists ( though at max we are loading data for 2000 rows)
4. Decreased the no. of KPIs to 14 in level 1 list view - all works fine.
We have not noticed any gradual decrease in performance/load time till 14th KPI but everything goes for a toss when the 15th KPI is displayed.
We are on the latest Xcelsius patch ( patch 3).
We would appreciate any pointers/help to resolve this issue.
Thanks in advance for your time.
Best Regards,
Bansi.

How many total rows are you dealing with in your spreadsheet?
-Dell

Unable to get the data from a website with dynamically filled textboxes when accessing through myWb.Document.GetElementById("num1").InnerText;

Hi Team,
I am learning on webbrowser control and during the learning phase i have the following issue:-
My webbrowser [mywb in this case] is successfully navigating and displaying the website content in webbrowser control. However; that site has three textboxes with dynamically allocated text from asp script
code behind; I have tried to display these textboxes values by providing the correct id of these textboxes in my visual studio 2013 code; but I am not receiving any data except null. Can you help me on this as early as possible.
asp code written to dynamically assign the data to textbox:-
<%
myvar=Request.form("some")
Response.write("<input type=text id=num1 value=" + myvar+ ">")
%>
The code written in VS 2013 to access the textbox by its id when the DocumentCompleted event is triggered:-
string mystr ="";
mystr = myWb.Document.GetElementById("num1").InnerText;
MessageBox.Show(mystr);
Thank You in Advance.
Regards, Subhash Konduru

Hello,
Thank you for your post.
I am afraid that the issue is out of support range of VS General Question forum which mainly discusses
the usage of Visual Studio IDE such as WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help System
and Visual Studio Editor.
Because the issue is related to website, I suggest that you can consult your issue on ASP.NET forum:
http://forums.asp.net/
for better solution and support.
Best regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Problem with Dynamic Node & UI Elements

Hi,
                                        The scenario is to create an Questioaire.Since the number questions which I get from R/3 may vary, I have created the Dynamic Node which is mapped with Dynamic set of Radio button Group by index for options & Dynamic text view for displaying Questions.. A New Dynamic Node will be created for each set of Questions .The Number of questions displayed per page is controlled by the Static Counter Variable....
                                          Now the issue is ,if i click back button the count will be initialized so again it needs to trigger the DoModifyView(). at that time It is arising an exception "Duplicate ID for view & Radio button ..." because while creating Dynamic node i used to have "i" value along the Creation of node name...
for(i=Count;i<i<wdContext.nodeQuestions().size();i++)
               customnod=<b>nodeinfo.getChild("Questionaire"+i);</b>
                    if(customnod==null)
Its not possible to create a new node whenever i click the Back button.
At the same time i am not able to fetch the elements which had already created Dynamically...
How do i make the Next & back button work?
If anyone bring me the solution It would be more helpful to me.
Thanks in advance..
Regards,
Malar

Hi,
      We can Loop through the Node Elements but how can we do Option Button Creation for each set of question Options?. At design time we can not have the radio buttons,because we do not know how many set of questions are available at the Backend.

VPN with Dynamic IP

Similar Messages

Maybe you are looking for