Wfload command in windows server

Hi,
In unix we use $FND_LOAD/bin/wfload command to upload .wft file, what is the command we need to use in windows server.
I checked %FND_TOP%/bin
I couldn't find any wfload.exe, i could see only WFRESGEN.exe.
Thanks.
With Regards,
Kali.
OSSi.

Hi Kali
I was able to find the same
I:\oracle\visappl\fnd\11.5.0\bin\WFLOAD.exePlease recheck
Thanks
AJ

Similar Messages

  • Could not able to execute FTP commands in windows server machines 2012/ windows server 2008.

    Could not able to execute FTP commands in windows server machines 2012/ windows server 2008.
    From windows server 2012 and windows server 2008, Opened port 20,21,22 in firewall bidirectionally. After Establishing connection by passing credentials  230 log in  successful.
    ftp commands executing getting as " 425 Use Port or PASV first" , "500 Illegal PORT command".
    But I could able to do windows client machines like windows 7 and windows 8 with same environment
    Note : Firewall ports are opened.  have tested by making firewall down to avoid filters. 
    Pandiyan Muthuraman

    Hi Pandiyan Muthuraman,
    Did you mean even you disable or open the related port the FTP issue still exist? I found this errors most time occur when we use the ISA firewall and the FTP configured passive
    mode, if you have ISA firewall please refer the following KB to fix this issue.
    How to enable passive CERN FTP connections through ISA Server 2000, 2004, or 2006
    http://support.microsoft.com/kb/300641
    The have a specific form for the IIS question, if you have the further IIS related question you can ask in IIS forum.
    IIS support forum
    http://forums.iis.net/
    Thanks for your understanding and support
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Running emctl command on windows server throws error

    Hi,
    I am uprading the the agent 10g to 11g on a windows 64 bit server.
    I have logged in as local admin user and running the below command.
    D:\app\oracle\product\agent10g\bin>emctl status agent
    Oracle Enterprise Manager 10g Release 5 Grid Control 10.2.0.5.0.
    Copyright (c) 1996, 2009 Oracle Corporation. All rights reserved.
    Unable to open file for logging. d:\app\oracle\product\agent10g/sysman/log/emctl
    .log: Permission denied
    Error in tempfile() using D:\app\oracle\product\agent10g\XXXXXXXXXX: Could not c
    reate temp file D:\app\oracle\product\agent10g\Dx9oDzw5h1: Permission denied at
    d:\app\oracle\product\agent10g\bin/AgentStatus.pm line 213
    I dont have the oracle user password on this box.
    I will appreciate if you can tell me how to resolve this?
    Thanks,
    Dnyanesh

    Hi Dnyanesh,
    You might probably be having the same issue mentioned in My Oracle Support Note 1164293.1
    Regards
    Lai

  • Issue with disabling teredo with Windows Server 2008(non R2)

     Hello,
    I am not able to disable teredo on Windows Server 2008 (non R2) .When I try to run the same set of commands on Windows Server 2008 R2 it works fine.I have followed the instructions as in the below link
    http://technet.microsoft.com/en-us/library/cc770710(v=ws.10).aspx
    C:\Windows\system32>netsh interface teredo show state
    Teredo Parameters
    Type                    : client
    Server Name             : teredo.ipv6.microsoft.com.
    Client Refresh Interval : 30 seconds
    Client Port             : unspecified
    State                   : offline
    Error                   : client is in a managed network
    C:\Windows\system32>netsh interface teredo set state disabled
    Ok.
    C:\Windows\system32>netsh interface teredo show state
    Teredo Parameters
    Type                    : client
    Server Name             : teredo.ipv6.microsoft.com.
    Client Refresh Interval : 30 seconds
    Client Port             : unspecified
    I have also tried changing the below registry to disable teredo , that didnot work as well.
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip6\DisabledComponents DWORD value set to 8.But the teredo status for the netsh command remains the same even after reboot.
    When I try to disable the 6to4 or isatap it works fine.I have checked in device manager ->network adapters with show hidden devices enabled, but I dont see teredo adapter even when teredo is enabled as per netsh.Also I dont see teredo adapter in add
    legacy hardware- > network adapters - > Microsoft devices , but I see isatap and 6to4 adapters in there.
    Can someone please help me..
    Thanks in Advance

    Hi,
    In device manager, add legacy hardware, install Teredo adapter, update the drivers. Reboot and check if you can modify the status.
    If this failed, reset tcp/ip stack.
    http://support.microsoft.com/kb/299357
    Hope this helps.

  • Not able to change product key in windows server using SLui command

    I have installed windows server 2012 r2datacenter and when I am trying to insert the product key using slui 3 command (in run windows),I am getting an error code as
    0x80070003(The system cannot find
    the path specified error)
    I have tried running sfc/scannow as well but it did not work.
    Kindly help me .

    Hi Ashish,
    Would you please let me confirm whether want to
    change the product key or activate the Windows Server 2012 R2 Datacenter? Just a confirmation, thanks for your understanding.
    Please use the
    Volume Activation Management Tool (VAMT) and check if help you to change the product key.
    In addition, please
    run the
    Microsoft Genuine Diagnostics Tool and check if find more relevant clues.
    If any update, please feel free to let me know.
    Hope this helps.
    Best regards,
    Justin Gu
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • How are Windows Server Backup and Command Line Tools used in vCSHB installation?

    How are Windows Server Backup and Command Line Tools used during the installation of vCSHB?  Is it required in all types of deployments (PtoV, VtoV, PtoP)? Is it used to create the files that are put in the file share for the second node to use during vCSHB installation or is it only used during a vCSHB clone operation of a Physical to Physical deployment?  Are these tools not used in some deployments?

    You need Windows Server Backup installed on source and destination, and during the installation of vCSHB the installer will invoke the wbadmin (Windows Server Backup Utility) and will backup configuration and application data (application data is optimal but can decrease the sync time after installation of secondary node). On the secondary node you will need only run the vCSHB installer and everything will be restored.
    Check this blog entry for some more info about some problems in P2P deployment: http://www.vcoportal.de/2013/12/vmware-vcenter-server-heartbeat-restore-on-a-second-node-a-journey/

  • Windows server 2012 Install-WindowsFeature command executing extreamly slow

    New server installed and we wanna install server features on it using powershell.
    Script start working, but nothing changed during long period time. Installation progress 24%.
    Internet is not accessable. Features installing from iso image mounted to vm.
    It's the same image which used for server installation.
    Any ideas- what's wrong?
    Command is:
    Install-WindowsFeature -Name
    $Feature-Source
    $windowsDistribLocal-LogPath
    $LogPathLocal
    resulted command is:
    Install-WindowsFeature -Name NET-Framework-Core -Source D:\ -LogPath C:\temp\installlog.txt
    In a log file was:
    2408: 2013-12-25 15:02:48.404 [ServerManagerPS]           Complete initializing log file.
    2408: 2013-12-25 15:02:48.606 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Enumerate server component ended with Success.
    2408: 2013-12-25 15:02:49.935 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Alter server component started. Component names: NET-Framework-Core,NET-Framework-Features
    2408: 2013-12-25 15:02:49.950 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Alter server component ended with InProgress. The progress is 20
    2408: 2013-12-25 15:02:50.965 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Alter server component started. Component names: NET-Framework-Core,NET-Framework-Features
    2408: 2013-12-25 15:02:50.981 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Get alteration state ended with InProgress. The progress is 24.
    2408: 2013-12-25 15:02:51.997 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Alter server component started. Component names: NET-Framework-Core,NET-Framework-Features
    2408: 2013-12-25 15:02:51.997 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Get alteration state ended with InProgress. The progress is 24.
    2408: 2013-12
    2408: 2013-12-25 15:07:36.510 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Alter server component started. Component names: NET-Framework-Core,NET-Framework-Features
    2408: 2013-12-25 15:07:36.510 [ServerManagerPS]           23326f59-1a36-403b-a2bb-1346f85867a5 Get alteration state ended with InProgress. The progress is 24.
    WinServ2012 on virtual box.

    Hi,
    Based on your description, I do the same operation in my Lab environment (Hyper-v and Windows Server 2012). Unfortunately, this issue can’t be reappeared. So, before
    going further, would you please let me confirm something?
    Did you mean that there was no error message when this issue occurred, just the progress was stuck at 24%? How long did you wait for the change approximately? Finally,
    can the feature be installed successfully or not?
    Meanwhile, please locate to C:\ Windows\ Logs\ CBS folder and check the
    CBS log if you can find some clues.
    If anything I misunderstand or more details you can provided, please don’t hesitate to let me know.
    Hope this helps.
    Best regards,
    Justin Gu

  • Command line error on Windows server 2008, GUI works

    I'm running Windows Server 2008 with a Blackmagic Decklink card. Everything works fine with the GUI but when I try to start from command line it extis with an error (see attached image).
    Note: I have the desktop experience enabled.

    I came across the identical problem with an Osprey card. I did some digging and for some reason, on Windows Server 2008, the "Desktop Experience" must be enabled for the command line version of FMLE to function. Not sure why this is, but it worked for me. Here's the note from Microsoft on how to enable this feature on your server...
    http://technet.microsoft.com/en-us/library/cc772567.aspx

  • Installing a New Windows Server 2008 R2 Child Domain by Using the Command Line

    Installing a New Windows Server 2008 R2 Child Domain by Using the Command Line:
    http://technet.microsoft.com/en-us/library/cc731873%28v=ws.10%29.aspx
    dcpromo /unattend /InstallDns:yes /ParentDomainDNSName:mysite.com /replicaOrNewDomain:domain /newDomain:child /newDomainDnsName:gridview.mysite.com /childName:gridview /DomainNetbiosName:gridview
    /databasePath:"c:\Windows\ntds" /logPath:"c:\Windows\ntds" /sysvolpath:"c:\Windows\SYSVOL" /safeModeAdminPassword:pass1 /forestLevel:4 /domainLevel:4 /rebootOnCompletion:yes
    Error Code:
    The specific argument 'childName' is not recognized.
    I am trying to insert gridview as a childname.

    Hi,
    Before going further, can we try another domain name to see what will happen?
    Besides, if the issue persists, we can try installing a new child domain by using the GUI.
    Installing a New Child Domain by Using the Graphical User Interface (GUI)
    http://technet.microsoft.com/en-us/library/cc771856(v=ws.10).aspx
    Best regards,
    Frank Shen

  • After installing Windows Server 2008 DATA CENTER stuck on blank screen and command prompt window

    After a new fresh install of Windows Server 2008 Data Center I get this solid blue screen with a comand prompt window showing (user\Administrator) I have limited use of the commands, am able to bring up the task manager by CTL Del and perform limited functions.  I was able to run the same software on this machine before, nothing has changed.  The way I ran the software on it before was from an image I deployed to it,(not from a fresh install).  The old image timed out and I could not rearm it, that is why I did a fresh install. I tried to use gpedit.msc but the command did not work.

    You may be using Windows with limited functionality as the previous version expired. Did you re-format the drive/partition before you did the "fresh" install if not Windows probably kept the old install information so knew that it was expired previously. Either activate Windows (try typing slui.exe and filling in the product key and activate - then restart the machine) or re-format the drive/partition that Windows is on and re-install Windows again.

  • SharePoint Foundation 2013 installed on Windows Server 2012 not sending out email notification

    I have a server where i installed SP Foundation 2013 on top of Windows Server 2012. I have configured the SMTP as well as the outgoing SMTP in Central Administration
    of SharePoint. When i create an alert on a document library, its did not sent any email notification on the changes made to the document in the document library. So, i created a workflow to send out email using SPD2013. The workflow run, but it cannot sent
    out email with error saying that outgoing email is not configured correctly. I have checked with another server which i installed SP foundation 2013 on top of Windows Server 2008 R2 - its sending out email just fine using same configuration and outgoing SMTP.
    I need help to resolve this issue or at least the cause of the problem.
    Any help is greatly appreciated.

         
    Try below:
    http://social.technet.microsoft.com/wiki/contents/articles/13771.troubleshooting-steps-for-sharepoint-alert-email-does-not-go-out.aspx
    Go to Central Admin ---->Operations----->outgoing email settings and verify that SMTP server is mentioned correctly 
    2) Test the connectivity with the SMTP server.
    In order to do that follow these steps:
      Open  cmd
      telnet <SMTP server name> 25 ( We connect smtp server to the port 25)  
                     you should see a response  like this 220 <servername> Microsoft ESMTP MAIL Service, Version: 6.0.3790.3959 ready at date and time
                     Beware that different servers will come up with different settings but you will get something
                     If you dont get anything then there could be 2 possible reasons, either port 25 is blocked or 
                     the smtp server is not responding.
      For testing response from your server
                       For testing response say ehlo to it.
                            Type :
                                        ehlo <servername>
                            output:
                                        250 <servername> Hello [IP Address]
      Now a test mail can be sent from that SharePoint server. 
                          Now we need to enter the From address of the mail.
                          Type :
                           mail from: [email protected]
                           output:
                           250 2.1.0 [email protected]….Sender OK
     It's time to enter the recepient email address.
    Type : rcpt to: [email protected]
    output:
    250 2.1.5 [email protected]
     Now we are left with the data of the email. i.e. subject and body.
    Type : data
    output:
    354 Start mail input; end with <CRLF>.<CRLF>
    Type:
    subject: this is a test mail
    Hi
    This is test mail body
    I am testing SMTP server.
    Hit Enter, then . and then Enter.
    output:
    250 2.6.0 <<servername>C8wSA00000006@<servername>> Queued mail for delivery
    Type: quit
    output:
    221 2.0.0 <servername> Service closing transmission channe
    3)  Check alerts are enabled for your web application
          verify if the windows timer service is running or not.
          Run this stsadm command to check that
          Stsadm.exe -o getproperty -url http://SharePoint-web-App-URL -pn alerts-enabled
         This should return <Property Exist="Yes" Value="yes" />
         If you don’t get this, Enable alerts by:
         stsadm.exe -o setproperty -pn alerts-enabled -pv "true" -url http://SharePoint-web-App-URL
          If its already enabled, try turn off and turn on it back.
    4)  Check the Timer job and Properties
           Go to
           MOSS 2007:  Central Administration > Operations > Timer Job Definitions (under Global Configuration)
           In SharePoint 2010: Central Administration > Monitoring > Review Job Definitions 
           Check whether the "Immediate Alerts" job is enabled for your web application. check these properties:
                       job-immediate-alerts
                       job-daily-alerts 
                       job-weekly-alerts
           stsadm.exe -o getproperty -url "http://Your-SharePoint-web-App-URL" -pn job-immediate-alerts
           The expected output is:
           <Property Exist="Yes" Value="every 5 minutes between 0 and 59"/>.  
           If you don’t get this, run the following command to set its value.
           stsadm.exe -o setproperty -pn job-immediate-alerts -pv “every 5 minutes between 0 and 59" -url http://Your-SharePoint-web-App-URL
    5)  Check whether the account is subscribed for alerts and it has a valid email account. This should be the first thing to check if the problem persists for some users not for      all.
    6)  Then check if at all those users have at least read permission for the list. Because the first mail should go out for every user without security validation but the next ones       won't be delivered unless the user has at least read
    permission.
    7)  If it is happening for one user, can also try to delete and re add the user in the site.
    8)  Most importantly , you should try this one.
          Run this SQL query to the content db < Select * from Timerlock>
          This will give you the name of the server which is locking the content database and since when.
          In order to get rid of that lock 
          Go to that server which is locking the content db and then restart the windows timer service.
          within some time it should release the lock from content db, if not then at the most stop the timer job for some time
          Once the lock will be released then try to send some alerts
          You will surely get the email alert.
    I found this is the most probable reason for alert not working most of the time. We should start troubleshooting with above steps before coming to this step for any alert email issue but from step 1 to step 7 are best for new environments or new servers.
    If the issue is like this ,alert was working before and suddenly stopped working without any environmental change then above conditions in step 1-7 should be ideally fine.
    Even after this if it is not working, then you can try these few more steps too
    9)  Try re-registering the alert template:
    stsadm -o updatealerttemplates -url http://Your-SharePoint-Web-App-URL -f  "c:\Program Files\Common Files\Microsoft Shared\web server extensions\12\TEMPLATE\XML\alerttemplates.xml" -LCID 1033
    10)  Try to clear the configuration cache
    If this helped you resolve your issue, please mark it Answered

  • I am trying to remote into a Windows Server 2003 from a Windows 7 machine and having issues

    I am trying to remote into a Windows Server 2003 from a Windows 7 machine.  It says "The terminal server has exceeded the maximum number of allowed connections".
    My first stop in trying to solve this problem was here:
    [URL="http://www.howtogeek.com/howto/windows/command-line-hack-for-terminal-server-has-exceeded-the-maximum-number-of-allowed-connections/"]howtogeek.com[/URL]
    And it says:
    [I]
    [INDENT]This problem happens because Windows only allows two remote terminal services connections when you are in administrative mode, and you’ve either got two people already on that server, or more likely, you’ve got a disconnected session that still thinks
    it is active.
    The problem with this error is that you have to actually get on the server console to fix the problem if the server isn’t in a domain. ([B]If you are in a domain, then just open Terminal Services Manager and log off or disconnect the sessions[/B])[/INDENT][/I]
    So it seems to suggest that all I have to do really is to run the  Terminal Services Manager but I cannot find it.
    This web site from mssqltips.com [URL="http://www.mssqltips.com/sqlservertip/1981/remote-desktop-error-terminal-server-has-exceeded-the-maximum-number-of-allowed-connections/"](click here)[/URL] says all I need to do is first execute "mstsc /
    admin" from the command line.  But, when I do that, I get a message when I try to remote to the server, that says this: "To log on to this remote console session, you must have administrative permissions on this computer".
    So, what now?  What do you suggest?

    Hi Bobby,
    Yes, it is by design. By default, Windows Server only accepts two concurrent administrative sessions (Administrative Mode). It means that only two administrators can work on the server at
    the same time.
    If you would like more concurrent sessions, you need to purchase RDS CALs, install Terminal Services related server roles with proper configurations on the server.
    Remote Desktop for Administration (server 2003)
    http://technet.microsoft.com/en-us/library/cc785186(v=ws.10).aspx
    What Is Terminal Services?
    http://technet.microsoft.com/en-us/library/cc782486(v=ws.10).aspx
    Terminal Services Configuration
    http://technet.microsoft.com/en-us/library/cc787078(v=ws.10).aspx
    Purchase client access licenses
    http://technet.microsoft.com/en-us/library/3660ac5a-7468-48d3-b7e8-5529de8fb6c5
    Thanks.
    Jeremy Wu
    TechNet Community Support

  • How to install Windows Server 2008 (dualboot) on a PC with Windows 8.1 already on it?

    Hi, I bought a new PC with preinstalled Windows 8. Now I need to install Windows Server 2008. Anyone can advise me how to
    do it? It has to be in dual boot, in Virtual Machine the display is way too small

    You should check out the Boot-to-VHD capability.
    Here is how we do it in a lab environment which we got from a Microsoft lab:
    -Verify your computer is running Windows 7 or later.
    -Verify you have full administrator rights to your currently installed operating system.
    -Verify hard disk encryption or other pre-boot security is turned off.
    -Confirm that hardware virtualization technology and memory protection are both enabled in your computer's BIOS setup.
    Now we just setup the a VHD with an operating system on it (can even use a downloaded server 180 day trial VHD if you are in a rush). Then go to Disk Management and select Attach VHD and point to the file. Note the drive letter that is assigned to the
    mounted VHD.
    Run a command prompt as administrator and type: " bcdedit /export BCDBackup.bak " to create an exported backup of your boot loader configuration. Now type bcdboot [drive]:\windows.
    Now to test your dual-boot configuration, restart your computer and select the new OS boot option.
    An optional last step would be when complete to restore your boot loader by running "bcdedit /import BCDBackup.bak" and delete any VHD files.
    A more detailed guide written for Windows 7 but still applies for Windows 8 can be found at:
    http://technet.microsoft.com/en-us/video/windows-7-boot-from-vhd.aspx
    Hope that helps.

  • Unable to install SQL server 2008 r2 standard edition on windows server 2008 r2 sp1

    I am unable to install sql server 2008 r2 standard edition on windows server 2008 r2 sp1.
     On the Setup Support Files page, choose Install this step I don't get any other window i.e. nothing happens I waited for 5-10 min.  Then I checked the log file.
    Final result:                  Failed: see details below
      Exit code (Decimal):           -2068053929
      Exit facility code:            1212
      Exit error code:               87
      Exit message:                  Failed: see details below
      Start time:                    2014-03-18 14:59:31
      End time:                      2014-03-18 15:00:25
    === Verbose logging started: 3/19/2014  9:45:47  Build type: SHIP UNICODE 5.00.7601.00  Calling process: E:\SQL Server 2008 R2 Standard\x64\setup100.exe ===
    MSI (c) (10:34) [09:45:47:496]: Note: 1: 2203 2: E:\SQL Server 2008 R2 Standard\x64\redist\watson\dw20sharedamd64.msi 3: -2147287038
    MSI (c) (10:34) [09:45:47:496]: MsiOpenPackageEx is returning 2.
    === Verbose logging stopped: 3/19/2014  9:45:47 ===
    Please help As i am running out of time as i have to upgrade TFS for that first step is to install SQL server.

    Hello,
    The following are a few things you can try:
    Copy the media to the local disk drive, unzip it (in case you are installing from an ISO file, and run SQL Server setup from there.
    Try to unregister and register the Windows Installer with the following two commands:
    msiexec /unregister
    msiexec /regserver
    Try to use Process Monitor to log the detailed error produced when the installation of dw20sharedamd64.msi fails. You can download Process Monitor from the following link:
    http://technet.microsoft.com/en-us/sysinternals/bb896645
    Share with us the error captured by Process Monitor.
    Hope this helps.
    Regards,
    Alberto Morillo
    SQLCoffee.com

  • Opening Excel Workbook Fails when run from Scheduled Task on Windows Server 2008 Rw

    Hi,
    I have a little vbs script that instantiates the Excel.Application object and then opens a work book to perform some tasks on it. The script runs fine when run from the command line. When I attempt to run it as a scheduled task (it is supposed to update
    data that is pulled from a SQL Server at regular intervals), it fails with the following error:
    Microsoft Office Excel cannot access the file 'c:\test\SampleWorkbook.xlsm'. There are several possible reasons: .....
    The file does exist. The path reported in the error is correct. The account under which the task is running is the same account I use to run it from the command line. User Account Control is not enabled, and the task is set up to run with highest privileges.
    When I run the same script through the Task Scheduler from a Windows Server 2003 machine, it works without issue.
    I was just wondering if somebody on this forum has run into a similar issue in connection with Windows Server 2008 R2 and figured out what the magic trick is to make it work. I'm sure it is rights related, but I haven't quite figured out what which rights
    are missing.
    Thanks in advance for any advice you may have.

    This is truly killing me ... trying to get it working on Windows Server 2012 without success.
    I desperately need to automate running Excel macros in a "headless" environment, that is non-interactive, non-GUI, etc.
    I can get it to work using Excel.Application COM, either via VBScript or Powershell, successfully on many other Windows systems  in our environment - Windows Server 2008 R2, Windows 7 (32-bit), etc.,  -BUT-
    The two servers we built out for running our automation process are Windows Server 2012 (SE) - and it just refuses to run on the 2012 servers - it gives the messages below from VBScript and PowerShell, respectively- 
    I have tried uninstalling and re-installing several different versions of Microsoft Excel (2007 Standard, 2010 Standard, 2010 Professional Plus, 32-bit vs. 64-bit, etc.), but it makes no difference.
    Would be extremely grateful if any one out there has had any success in running Excel automation on Server 2012 in a non-interactive environment that they could share.
    ( I have tried adding the "%windir%\syswow64\config\systemprofile\desktop"
    folder, which did fix the issue for me when testing on Windows Server 2008 R2, but sadly did not resolve it on Windows Server 2012 )
    [VBScript error msg]
    Z:\TestExcelMacro.vbs(35, 1) Microsoft Office Excel: Microsoft Office Excel cannot
    access the file 'Z:\TestExcelMacro.xlsm'. There are several possible reasons:
    • The file name or path does not exist.
    • The file is being used by another program.
    • The workbook you are trying to save has the same name as a currently open work
    [Powershell error msg]
    Exception calling "Add" with "0" argument(s): "Microsoft Office Excel cannot open or save any more documents because th
    ere is not enough available memory or disk space.
     To make more memory available, close workbooks or programs you no longer need.
     To free disk space, delete files you no longer need from the disk you are saving to."
        + CategoryInfo          : NotSpecified: (:) [], MethodInvocationException
        + FullyQualifiedErrorId : ComMethodTargetInvocation
    You cannot call a method on a null-valued expression.
        + CategoryInfo          : InvalidOperation: (:) [], RuntimeException
        + FullyQualifiedErrorId : InvokeMethodOnNull

Maybe you are looking for