What is solution of nat failover with 2 ISPs?

Now I have lease line link to 2 ISPs for internet connection. I separate packets of users by accesslist such as www go to ISP1 and mail or other protocol go to ISP2 . Let's say link go to ISP1 down I need www traffics failover to ISP2 and vice versa.
Problem is acl on nat statement?
If you config about this.
access-l 101 permit tcp any any www -->www traffic to ISP1
access-l 101 permit tcp any any mail --> back up for mail packet to ISP2 down
access-l 102 permit tcp any any mail -->mail packet to ISP2
access-l 102 permit tcp any any www --> back up for www traffic go to ISP2
ip nat inside source list 101 interface s0 overload
ip nat inside source list 102 interface s1 overload
In this case is links of ISP1 and ISP2 are UP.
when you apply this acl on nat statement then nat will process each statement in order( if I incorrect please correct me) so mail traffics will match in this acl and then nat with ip of ISP1 only.
please advice solution about this
TIA

Hi,
If you have two serial links connecting to two diff service provider , then you can try this .
access-l 101 permit tcp any any www
access-l 102 permit tcp any any mail
route-map isp1 permit 10
match ip address 101
set interface s0
route-map isp2 permit 10
match ip address 102
set interface s1
ip nat inside route-map isp1 interface s0 overload
ip nat inside source route-map isp2 interface s1 overload
ip nat inside source list 103 interface s0 overload
ip nat inside source list 104 interface s1 overload
ip route 0.0.0.0 0.0.0.0 s0
ip route 0.0.0.0 0.0.0.0 s1 100
In case if any of the link fails , automatically the other traffic would prefer the other serial.
I have not tried the config , just worked out the config on logic .pls go through and try if possible
pls see the note2 column
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080093fca.shtml#related
Hope it helps
regards
vanesh k

Similar Messages

When I create a PDF with Adobe Reader XI, it wont take the links behind the images. Sometimes he does, mostly not.. Whats the solution? The links in text do work!

When I create a PDF with Adobe Reader XI, it wont take the links behind the images. Sometimes he does, mostly not.. Whats the solution? The links in text do work!

Hello,
How can I give a answer back in the discussion on Adobe.com?
I don’t see any link?
1.      We have a subscription.
2.      Im converting a newsletter from the web to PDF.
3.      Sometimes I put a weblink behind the image in the newsletter. Most of the time PDF wont take the links behind the image.
Only the tekstlinks are OK.
[private data removed]

HT3775 my avi format is not being recognised everytime i try to play a movie through quicktime player...how do i get it to be recognised or what is solution please?? be easy on im a beginner with this mac book! thank you

my avi format is not being recognised everytime i try to play a movie through quicktime player...how do i get it to be recognised or what is solution please?? be easy on im a beginner with this mac book! thank you

Download and install Perian or VLC from the web.
Message was edited by: hpr3

IE9, Win7: How to get rid of "What do you want to do with ...doc? Open, Save, Save as

My web application downloads a .doc file. With IE9 and Windows 7 it displays the dialog "What do you want to do with xxxx.doc? Open, Save, Save as" Prior to IE9 I could check the box that said "remember" but with IE9 I do not see a way to prevent
the dialog from occurring every time. How can I turn off this dialog like I can in all prior versions of IE? I have looked through the forums and the answer might be here but most threads seem to be a little different problem. Some of my
customers are switching to FireFox and Chrome because of this problem so I would like to find a solution. I found another thread that had a potential solution (1. Click Tools - Internet Options - Security Tab. 2. Click Local intranet, click Sites, uncheck
"Automatically detect intranet network" if you checked it. Then check "Include all network paths (UNCs)". Click Advanced, add the intranet to the zone. Then Close and OK.) but that did not solve my problem.

Hi,
Based my research, due to increasing in security, we cannot disable Download Manager of Internet Explorer 9 from changing settings, editing registry keys or editing settings in Group Policy. This can prevent websites downloading automatically. Instead, we can
set default download location.
For reference:
http://social.technet.microsoft.com/Forums/en/ieitprocurrentver/thread/21798a87-8c04-4995-a988-ed9275062f82
And for more detailed information, please refer to
Safer and Faster Downloads in IE9.
Hope this helps.
If a post solved your problem, click “Mark as Answer” on the post. If a post helped you, click "Vote As Helpful" on the left side of post.

What does a flashing folder icon with a "?" inside mean?

What does a flashing folder icon with a "?" inside mean?

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark or globe appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

JMS Failover with Distributed Destinations in 7.0

          How does JMS failover with distributed destinations in WL 7.0?
          In an environment using file stores for persistent messages, can a working server
          automatically pick up unprocessed and persisted messages from a failed server?
          If so, what's the best way to set this up?
          Or, is this completely manual? In other words, we have to bring up a new server
          pointing to the location of the file store from the failed server?


          It appears that two JMSServers cannot share the same file store and, I'm assuming,
          two file stores cannot be using the same directory for persistence.
          So the HA you're talking about is something like Veritas automatically restarting
          a server (or starting a new one) to process the messages in the persistent queue
          that were unprocessed at the time of failure with the file store residing on some
          sort of HA disk array.
          The key point is that a message once it arrives at a server must be processed
          by that server or, in the case of failure of that server, must be processed by
          a server similarly configured to the one that failed so that it picks up the unprocessed
          messages. The message can't be processed by another server in the cluster.
          Or, is there some trick that could be employed to copy from the file store of
          the failed server and repost the messages to the still operating servers?
          "Zach" <[email protected]> wrote:
          >Unless you have some sort of HA framework/hardware, this is a manual
          >operation. You either point to the existing persistent storage (shared
          >storage or JDBC connection pool), or you move the physical data.
          >
          >_sjz.
          >
          >"Jim Cross" <[email protected]> wrote in message
          >news:[email protected]...
          >>
          >>
          >> How does JMS failover with distributed destinations in WL 7.0?
          >>
          >> In an environment using file stores for persistent messages, can a
          >working
          >server
          >> automatically pick up unprocessed and persisted messages from a failed
          >server?
          >> If so, what's the best way to set this up?
          >>
          >> Or, is this completely manual? In other words, we have to bring up
          >a new
          >server
          >> pointing to the location of the file store from the failed server?
          >
          >

What are solutions to the "Unexpected error while attempting to bind. Operation cancelled." message when trying to bind

What are solutions to the "Unexpected error while attempting to bind. Operation cancelled." message when trying to bind and i alreeady cheack my DNS settings and everything

Has this worked before, or is this a new configuration?
On the server, launch Terminal.app from Applications > Utilities and post the output of the following harmless diagnostic command — and you'll need to enter an administrative password when requested:
sudo changeip -checkhostname
On the OS X (presumably) Mavericks client, please post the IP address(es) of the DNS server(s) you're referencing. These are available via the System Preferences > Network > Advanced > DNS settings.
To check the console logs, launch Console.app from Applications > Utilities on both the client and the server, and then attempt the binding, and then post a (short! no more than ~25 to 50 lines!) of any errors related to the binding error.
If you're not in a position to post configuration details here — which is perfectly reasonable, and entirely your prerogative — or if I'm getting too confusing or too technical with some of the questions here, which would be my error of course — then (assuming these systems are under warranty) I'd suggest contacting the folks at the local Apple Store and having a chat with the local Geniuses about this, or checking directly with the Apple Support folks via telephone.

Lenovo Solution Center not compatible with Win 8.1 ?

After teh Windows Update on November 16th ... The soltuions center display a critical error syaing theat my Windows was never updated !?! Any other having this bug ? I wonder what prevents my Solution Center software from reading the update history !!! ...

Hi Griggs1,
Welcome to the HP forums!
I see you're having issues getting the Solution Center to work with your new Windows 8.1 laptop. I'm sorry to hear this, but with a bit more information I'd be happy to lend a helping hand
1. What model HP printer do you have?
2. Is the printer connected via USB or wireless?
3. Are you able to run the scan even though the Solution Center says the printer is disconnected? (I only ask because I've seen it many times!)
4. Have you tried downloading and running the HP Print and Scan Doctor yet? If not, please try that and let me know what it has to say! If it fails anywhere, just let me know where it fails.
5. Did you install the printer using a download?
Once I have this information I will certainly do my best to have a deeper look into things!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with AP 1242

Dear all, my customer has CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with 12 AP1242 (a/b/g) Radio 802.11g in place. Now he will buy additional AP what type of AP can i use because AP 12xx is EOS.

Hello Dirk,
AP 1200 is EOS, and customers were encouraged to migrate to 1240 Series (which is also EOS now)
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1200-series/eol_c51-506611.html
Therefore it is recommended to migrate to Cisco Aironet 1600 or Cisco Aironet 2600 Series.
http://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-ip-phone-7900-series/end_of_life_notice_c51-726425.html

What video codecs can be used with Premiere CS4?

What video codecs can be used with Premiere CS4? Or are there to many to list? I'm looking for a solution to import a .AVI file created with a H.264 codec.

PrPro can work with so very many, but certainly not all. Some, like DivX will work for Export, but I have never gotten good Import of that material - always something wrong somewhere.
For H.264, there are three very popular versions: Apple, Lead and MainConcept. The Apple version installs with later versions of QT Player, the other two are available, and many users like them better. They solve some H.264 problems, mainly with Export.
For a bit of background, you might find this ARTICLE useful.
Good luck,
Hunt

RMI-NAT Problem with random ports

Hi,
I had a RMI server in a machine with the private IP 10.XX.XX.XX and a firewall with the public IP 196.XX.XX.XX
I am using the property: java.rmi.server.hostname to 196.XX.XX.XX and a small test application. The server is behind the firewall/NAT machine with a limited set of open ports (including the non standard 8001 port that I am using instead 1099)
1. The server start perfectly
2. The client can connect to the server and execute the method Naming.list() successfully
3. At the moment that the client attempt to perform the bind, the client hang up for almost 7 minutes and finally throws and exception due time-outs.
According a "strace" and "netstat" commands under Linux and also the flag: java.rmi.server.logCalls we obtain the next data:
1. The server open the port 8001 (PERFECT)
2. But also open a random port and the client -at the bind moment- use that port (in the range 34000-35000). And of course our firewall block all the ports except 8001.
So, is that the expect behaviour? If that is true then RMI is not functional under NAT/Firewall.
Am I missing something?
Thanks!!
Gerardo

Hello,
Let me see if I got it right:
1. You're starting the registry (programatically) in port 8001.
2. You're creating a server implementation object.
3. Next you bind/rebind your server to this registry.
4. Your client hangs at Naming.lookup().
If this is the problem then that random port you mentioned is the server's attributed port (a ServerSocket that is hanging on accept) at the time of creation. You can avoid this by instead of using the super() call in you serverimpl constructor using the UnicastRemoteObject constructor that specifies a port (check the interface). That way you can configure your firewall to allow traffic through that port too.
However, what puzzles me is the fact that it hangs on step 4 instead of in a subsequent remote call. step 4 should be using port 8001. Can you confirm that it's hanging in Naming.lookup ?
(two other sources of data you may find usefull are the Firewall logs and a tcpdump analisys of the traffic between the firewall and the server machine)
Nuno

What can solution manger can do for me as a basis,and as a bussiness ?

dear all ,
i want to know the benefits and the usage of the solution manager?
and what sap solution manger can do for me?
thanks in advance
Mahmoud Younis

Hi
service desk/support desk/incident management
Application Incident Management process provides central message management and processing. The Application Incident Management, with its integration of SAP Customer Relationship Management (SAP CRM) IT Service Management, allows us to contact all parties involved in a message. These include all users of the system landscape or your company's solutions, such as employees, customers, consultants or support staff.
demo is here
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/904036f4-58ed-2c10-b0b9-c6c7ca0b5afc
for other stuff also you can easily click on eLearning on sdn and choose Solution manager to get overview of features and demo etc.
Hope it clarifies your doubt
Regards
Prakhar

What Speedlite (or generic) flash works with the SX50? Thanks.

Hello & Merry Christmas to all,
Trying to find out what flash is made to work with the SX50. Seems like unless you have a DSLR, there isn't much info. I checked under Canon PowerShot. I'm very new to photo', so I'm asking a newbie question.
Speedlite or other brand flashes for the SX50 hotshoe. One that works with the camera, not just a 'flash'... Thanks

Felix,
The following flash models are supported:
Speedlite 220EX
Speedlite 270EX
Speedlite 270EX II
Speedlite 320EX
Speedlite 430EX
Speedlite 430EX II
Speedlite 580EX
Speedlite 580EX II
Speedlite 600EX
Speedlite 600EX-RT
If this is a time sensitive-matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

What hosting platform must i use with iweb? unix or microsoft

what hosting platform must i use with iweb? unix or microsoft? This is a question from my ISP.

You should always pick Linux hosting and NOT Windows - this causes more problems than it is worth.
If your ISP is asking this question, then consider changing - they should know this.

I have a third gen. iPad which after downloading ios8.02. is locked. Whats the solution?

I have a third gen. iPad which after downloading ios8.02. is locked. Whats the solution?

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

What is solution of nat failover with 2 ISPs?

Similar Messages

Maybe you are looking for