When I start up my new Imac with my password, it works but after going into sleepmode, I can't go out of the sleep moed with this password

I did the configuration of my new Imac and entered and confirmed my password when asked.
When my computer is switched of, I can startup with this password but after going into sleepmode, this password doesn't work.
The same when I go to "system preferences" users & groups, it's not possible to unlock the lock with this password
I'm sure that I never used another password.

If Apple was the one that replaced the ribbon cable, return it. If not, run AHT (Apple Hardware Test).
Using Apple Hardware Test to troubleshoot a hardware problem
Your issues might be caused by a hardware problem. Running Apple Hardware Test can help you solve this problem by showing you the faulty hardware.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
Press the Power Button to turn on the computer.
Press and hold the D key on the keyboard before the grey starting screen appears.
Continue to hold the D key until the loading screen shows up. You should see a globe.
When AHT has loaded, select your Language and then press the Return (↩) key.
Select the Perform Extended Testing checkbox located under the Test button.
Press the T key, select the Test button, or press the Return (↩) key to start running the diagnostics.
Report any issues it shows in a reply.
I hope I helped.

Similar Messages

Have new iMac with iPhoto sharing turned on. When the shared library is clicked the library disappears or starts to load then disappears? What is wrong?

Have new iMac with iPhoto sharing turned on. When the shared library is clicked the library disappears or starts to load then disappears? What is wrong?

Try this: launch iPhoto with the Option key held down and create a new, test library. Import some photos and check to see if the same problem persists. If it doesn't then your current library is damaged and needs repair.
Therefore make a temporary, backup copy (select the library and type Command+D) and apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Since only one option can be run at a time start with Option #1, followed by #3 and then #4 as needed.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option
In the next window name the new library and select the location you want it to be placed.
Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
If you experience the same problem with the test library then try this basic fix a try: make a temporary, backup copy (if you don't already have a backup copy) of the library and try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
User/Home()/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
User/Home()/Library/Caches/com.apple.iPhoto folder.
Click to view full size
3 - launch iPhoto and try again.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.
NOTE 2: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
If that fails a reinstall of iPhoto is indicated. To do so you'll have to delete the current application and all files with "iPhoto" in the file name with either a .PKG or .BOM extension that reside in the HD/Library/Receipts folder and from the /var/db/receipts/ folder,
Click to view full size
Then install iPhoto from the source it came on originally.
OT

Does anyone know why or what is the reason when starting a new iMac with Lion a gray bar sometimes appears when loading software?

Does anyone know why or what is the reason when starting a new iMac with Lion, sometimes a gray bar appears under the Apple that begins to shade to dark as it loads OS? It does this on occasion. One time the system loaded was VERY slow and terrible colors. Pulled the plug, re-started the computer and it did not do this. As I say, its only on occasion, not every time. I noticed in the discussion page there were problems listed for 10.6 nothing for Lion.
Please advise, if possible.

You should see this 4 option menu. Click on Disk Utility:
In Disk Utility, Select FIRST AID and then VERIFY and then REPAIR the disk.
Ciao.

I am using a new imac with osx lion 10.7.5 and have bought a copy of Apple iLife 11 on dvd a so that I can install iWeb and idvd, when I click on install iLife I get a message saying "iLife.kpg was signed with an invalid certificate

I am using a new imac with osx lion 10.7.5 and have just bought Apple iLife 11 on dvd so that I can install iWeb and iDVD, as macs no longer ship with these apps. When I click on install iLife I get a message saying "iLife.kpg was signed with an invalid certificate.
Next problem is that when moving through the installer and get to custom install, as I only want to install iDVD and iWeb, I am presented with the option to install iDVD, Sounds & Jingles and iWeb, but not sure what is going on with the other 3 options iLife Support etc, they seem to be greyed out but still look like they may install over the top of the newer versions already on my imac. Is it ok for me to just go ahead and hit install? Or do I have a problem?

Yep, just install iDVD (plus sounds and jingles) and iWeb if you want it (but note that iWeb apparently won't work if you upgrade to Mountain Lion).
Then use Software Update to get any late iDVD updates.

I have a new iMac with osx 10.8.3 i can not get my hp laserjet m1522nf scanner to work. The printer works but when in scanner mode the scanner does not show up

I have a new iMac with osx 10.8.3 i can not get my hp laserjet m1522nf scanner to work. The printer works but when in scanner mode the scanner does not show up.I tried to install the newest hp driver for the printer but when I install the computer ca not find the printer.

Repair permissions and restart your computer.
Make sure you have the updated scanner drivers installed.
Install the gimp drivers: http://gimp-print.sourceforge.net/MacOSX.php
http://support.apple.com/kb/PH11070 OS X Mountain Lion: Troubleshoot a network printer
http://support.apple.com/kb/PH11143 OS X Mountain Lion: Reset the printing system
http://support.apple.com/kb/HT3669 Printer and scanner software available for download
What to do when you can't print

Installing Photoshop cc on a new iMac with retina display , but when PS opens , i receive following message;

i installed photoshop on my new iMac with retina display. I worked always with a windows pc , and i am completely new in the macworld. When i opened photoshop the first time , i saw the following message ;
open system preferences, click on design (in dutch it calls vormgeving) and switch off the function for smooth text for fontsize 8 and smaller to display the user interface off photoshop correctly.

10.9: Ps Error message "...to display correctly...turn off text smoothing for font sizes 8..."

My new iMac with FCPX crashes when rendering complex templates and crashes when exporting with Motion 5

My new iMac with FCPX crashes when rendering complex templates and crashes when exporting with Motion 5
Using Motion 5.0.6 and Final Cut Pro X 10.0.7 on New iMac (December 2012) Mountain Lion,
Intel Core i7 quad-core a 3,4GHz, Turbo Boost fino a 3,9GHz
32GB di SDRAM DDR3 a 1600MHz - 4 x 8GB
Fusion Drive da 3TB
NVIDIA GeForce GTX 680MX 2GB GDDR5
During the rendering of complex FCPX mac crashes and I have to force a restart.
I also happens when I try to export movies with Motion 5.
Does anyone have the same problem with my new iMac?

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore will not, in itself, solve your problem.
First, empty the Trash.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Triple-click anywhere in the line below to select it, then drag or copy it — do not type — into the Terminal window:
find . $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 -o -acl $ 2> /dev/null | wc -l
Press return. The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
The output of this command, on a line directly below what you entered, will be a number such as "35." Please post it in a reply.

I have a new Imac with OS Lion. When i use the apple migration tool to transfer from my PC to the Mac, it runs for two hours or so exchanging my pictures and address book, but when completed, I cannot locate anything on the Mac! Any suggestions?

I have a new IMAC with lion. When I use the migration tool from my PC to the new Mac, it takes about 2 hours to transfer my photos and address book, etc. However, when completed, I cannot locate any of the transfered material on the Mac! Any suggestions?

You have posted to the older PPC iMac forum. You need to poster to a newer iMac forum.
I suggest posting here:
https://discussions.apple.com/community/mac_os/mac_os_x_v10.7_lion?tagSet=1382
Complete list:
https://discussions.apple.com/docs/DOC-2463
Try double clicking on the harddrive icon on your desktop
You should get something like this.
On the left pane is a list of common places.
All the user data is in the /Users folder.
See the magnifying glass on the upper left of the screen. This is spotlight. Type in a file name.
Robert

Just bought a new iMac, with Lion, for my wife. When is was wifi with her old iMac on line with it's printer, HP C6200, no problems printing. Now that it is by itself it does not recognize the C6200...It recognizes my laser hp 1012 and laser hp 6300

Just bought a new iMac, with Lion, for my wife. When is was wifi with her old iMac on line with it's printer, HP C6200, no problems printing. Now that it is by itself it does not recognize the C6200...It recognizes my laser hp 1012 and laser hp 6300 but will not print to them wanting an autenication

How is the C6200 connected to the iMac, is it via USB or Wi-Fi? If it's via Wi-Fi please make sure it's connected to the router using the printer's Network Wizard. Then click System Preferences - Print & Scan and assuming the iMac is on the same network as the printer, if it is the printer should be seen. If it's not then click the + sign and add the printer. Apple provides instructions in Printing Overview OS X Lion

Recently got new iMac with Lion.....when I try to load my LogicPro software, I get 'OS does not support power PC'. Is there a download to fix or must I spend another 500 on software?

Recently got new iMac with Lion.....when I try to load my LogicPro software, I get 'OS does not support power PC'. Is there a download to fix or must I spend another 500 on software?

What version of Logic do you have?
And if you end up upgrading, it's only $199 now.

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

Reinstall OS X:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

Have new iMac with latest version of quicktime. But still have FCP5. When try to make a quicktime movie this version only processes 8 sec of a 7 minute sequence. What's up?

Have new iMac with latest version of quicktime. But still have FCP5. When try to make a quicktime movie this version only processes 8 sec of a 7 minute sequence. What's up?
Mike T.

It is strange. I thought 10.x might be the more recent but it also locked up when I tried to the web export. I ran into the no autoplay issue with the webpage so I'll need to look elsewhere to replace a Flash gallery... oh well. Looks like there are probably JS option that might work.
Thanks.

When support After Effects Ray-traced 3D the GPU of the new iMac with retina display (GPU: AMD Radeon R9 M295X 4GB)?

I would like to know whether After Effects CC Ray-traced 3D support the GPU of the new iMac with retina display.

It never will. This is nVidia-exclusive technology and the whole things is deprecated, anyway. You better learn to use Cineware, buy a 3D program like Pro Animator or Element 3D or learn a proper 3D program.
Mylenium

How to get batch recognition of (!) on some tracks after moving library from external hard drive to new iMac (with terabyte hard drive)?

I'm using Lion 10.7.2 and iTunes 10.5.2
I have moved my iTunes music from an external hard drive onto my new iMac (with a terabyte hard drive) with music folder organized - when I try to play some tracks I get the iTunes can't locate warning and so I follow through and show iTunes the track - they are all in the music folder on my iMac hard drive - they all copied over and they all appear in the iTunes library list - so far as I can tell out of a 500 gigabyte music collection - but there are so many giving me the error - many other tracks function as they should too, some work others don't - So I'm looking for a way to get all the error tracks fixed in a batch correction way. Doing this individually with each track just isn't realistic.
Can anyone suggest how I might fix this issue?
Also, after I show iTunes the song location and it plays, I get a find files prompt that looks like it wants to find other files, but that just causes the process to jam and I have to force quit iTunes and then it doesn't remember what I last showed it next time I open iTunes.
Also I'm trying to avoid the use of the consolidate function because that would copy a whole other set of music - not in iTunes - that is in the process of being edited (audio hijack pro and fission tools being used to put vinyl and tapes to mp3) But all that other music just means the consolodate function across my whole computer would be too much.

Some details seem to be coming into focus - I have started scrolling through the main library list A to Z repairing tracks individually (there are thousands, but it's what works so far) - as I work through, it appears the problem occurred on tracks where album artist metadata was different than song artist metadata, predominantly. I'm not sure that is 100% the case in every instance, but that is what it's looking like. I don't why that happened, must be some technical glich I guess.
Also, I tried running Doug's Scripts - the one titled, iTunes Track CPR v1.3 - it is supposed to fix exactly the kind of issue I'm having - I bet it would work for some people with a similar issue - but for my case it only identifies the 'de-linked' tracks and doesn't repair them - that is at least helpful as I scroll though to fix them - I can see exactly which tracks have the issue quickly after running that script - but iTunes doesn't remember that warning symbol after a log-out, so it's only worth running the script on a set of tracks I intend to review and fix in any given session at a time.
If you are interested, Doug's free scripts can be found at
http://dougscripts.com/itunes/scripts/ss.php?sp=itunestrackcpr
there are other interesting and useful iTunes scripts there too...
also, unrelated to the issue I'm having, I found a lot of really useful and time saving metadata fixing free scripts at - hubi's iTunes scripts - the page isn't English, but the script download is easy to find -
hubi's scripts work for batch selections of tracks - so if you import an album and find the metadata screwed up somehow, you can select the whole set of screwed up tags at once (even across a series of albums), run the easy to use script, and watch it all be fixed automatically while you sit back and relax...
http://hubionmac.com/wordpress/category/softwareschmiede/applescripting/itunes/
just for reference, here is a sampling of what hubi's scripts can do...
there are other useful scripts out there - the tough part can be finding the one that helps you...
01-(un)capitalizes
01-(un)capitalizes
This script changes.... THIS TEXT into This Text... or this text
01-Delete spaces
Sometimes invisible blanks are behind an artist name or album name...this script deletes these blanks behind or infront of the strings
01-Delete x first-last chars. of Title
A Name like "01--Ray Of Light" will be changed to "Ray Of Light" and the01 will be entered in the tracks tracknumber id3 field =)
01-fix combined Artist-Title
Sometimes Tracknames look like:
"Madonna---Ray of Light" and in the artist field you see something like"Ripped by Me"... this script puts Madonna back to the right field... all youhave to do is to enter the right delimiter ("---" in this case)
01-switch Artist<->Title...
Switch ID3 field a with ID3 field b (not only Artist with Title any more =)!
01-z_filename ->Title
Sets the ID3 field Title to the track's filename)
01-z_trackNr-Filename->ID3
When a track's filename look like "01-Madonna-Ray of Light.mp3" andyou don't have the track's tracknumber stored in the ID3 Tag... this Scriptcan do this for your =)

Can't back-up new iMac with fusion HD. The back-up proceeds to within 10% of the total storage needed and then the "of" number increases. I suspect there is a problem with backing up the fusion drive. We have a new 3 TB time Capsule. Any ideas?

Can't back-up new iMac with fusion HD. The back-up proceeds to within 10% of the total storage needed and then the "of" number increases. I suspect there is a problem with backing up the fusion drive. We have a new 3 TB time Capsule. I tried excluding different parts of the software from the back-up but it didn't make any difference. I even tried exluding "invisible items" to no avail. Any ideas?

When you setup the wireless and ethernet in the computer.. ipv6 will be on automatic.. this is wrong for the latest TC firmware and airport utility. http://support.apple.com/kb/TS4597
Go to the wireless and ethernet setup in preferences and change ipv6 to link local.
Once you do the big backup by ethernet the wireless will function fine for incremental.. it is obviously not estimating the size correctly..
A full back-up on the iMac would be about 650 GB. The partial updates that I have been trying start out at 115MB and keep growing indefinitely. The original back-up never finished nor have any of the follow-up attempts.
The first estimate should be the full backup but it will keep growing as the backup advances.. I would also delete any inprogress files to make sure it is not messing up .. delete even a sparsebundle if there is one for the imac on the TC and start afresh once you have ethernet connection.
See A10 here.
Pondini may have some other clues there to give you an idea of why the backup is slow or not finishing.. there is a lot of issues with TM when it decides not to work.

When I start up my new Imac with my password, it works but after going into sleepmode, I can't go out of the sleep moed with this password

Similar Messages

Maybe you are looking for