Why is that power LED blinking?

the power LED on the MSI k7n2g blinks a lot on my computer.  It's supposed to be a message LED, but what is the message it's sending!?!?!?  Is it morse code?  IT would have been a REALLY good idea it put a key to the code inthe manual!
Anybody know?
(BTW, I have had several issues regarding the onboard video, but after an update to the drivers and bios, it does seem to operate more stably now, AS LONG As I don't use anti-aliasing and anisotropic filtering or texture sharpening...or set the memory bus to 200Mhz with my ddr400 memory....)

maybe ur power led and hd led got switched around by accident, check the wire, if you think its right but it still does it, try switching the power led wire with the hd led wire.

Similar Messages

  • WRT54GL - Power Led blinking after unsuccessful flash-attempt

    Hi there, I wanted to flash my wrt54gl with some other version of dd-wrt firmware. There was another dd-wrt image on it before the flash, but when I chose to "upgrade" the firmware, the router hung with power led blinking and the SES button active. So I aborted the flash with a powercable-unplug, and plugged it in again. Since then the router doesn't start up any more. I don't get an IP via DHCP, with static configured IP 192.168.1.2, pinging 192.168.1.1, I get a response, but I can't get to the web interface again. I tried the 30sec Reset-trick, didn't work out. I tried to upload the original Linksys firmware via the Linksys TFTP-tool, which didn't work out either. U got some other clues, what I can try to get my wrt54gl back alive again? greets gothic5k

    Hey try resetting the router reset button in such a way that power
    light is blinking on the router & then do a complete network power
    cycle i.e., unplug the power cables from the modem & from the router &
    then plug in the power cable to the modem first once all the lights are
    solid green you could plug in the power cable to the router & check out
    it will definately work!!

  • Power LED Blinking Orange/White..Hardware problem?

    Power LED Blinking Orange/White.
    i am using a compaq cg56-102tu laptop. i wont turn on and nothing happens when i press the power button and theres a blinking orange and white light at the power indicator LED when the battery or ac adapter is connected..
    courtesy of vaiost
    it is like that when i plug the laptop on an outlet with or without the battery..it is the same when i only use the battery but it starts blinking when i connect the battery even without pressing any button..Any ideas?

    Hello @NoGameNoLife,
    I have read your post on how your notebook computer is not able to power on, and I would be happy to assist you in this matter!
    Since there is a blinking orange light where the AC adapter plugs into your computer, I recommend following this document on Computer does not start and the LEDs blink or the computer beeps, as well as Using and Testing the AC Power Adapter. This should help to restore the power to your notebook.
    If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • U205 s5022 Power LED Blinking

    U205 s5022 Power LED Blinks amber color as follows: Blinks 3x pauses Blinks 3x pauses blinks 2x pauses and repeats cycle. Power Adapter checks OK at 19 Volts DC and have installed new battery. Computer still won't start. What could be probable cause of consistent blinking light?

    Initial reply led me (thank you) to recheck the power adapter I was using. It turned out it was for 19 volts DC and this lap top only takes 15 volts DC hence the blinking lights. After replacing the CMOS battery and tinkering with other stuff (which I later learned were unnecessary but educational)  like the motherboard, reseating CPU heat sink etc. - the unit is now working but will just stay idle because I have been a MAC person for many years now.

  • E2500 Power LED Blinking

    I'm using an E2500 and the Power LED started blinking this week.
    From the manual, this means   “Flashes slowly during bootup, during firmware upgrades, and druing a Wi-Fi-Protected Setup Connection.” We have a wireless printer (wireless disabled), and a Kindle that does use wireless. All other computers are hard wired.  I have not started a Wi-Fi protected setup. The router has been in use since the third week in October, and is more or less OK even though the Power LED is flashing. 
    Why is is flashing?  How do I get the Power LED to stop flashing?
    Thank you.

    Yes, internet connection via the router seems to be OK (both hardwired and wireless).   There may be some degradation, but I'm using a satellite provider so it may not be the router.   However, intermittant connections have occurred within the past few days and that's the same time frame at which I noticed the light blinking.  There may or may not be a correlation.
    We power down all our equipment when we go to sleep (modem, router, computers etc) and power them up each morning.
    The firmware version  on the web site is the same as in my unit.
    I do notice that when I log into the router page the light stops blinking.   When I exit the page it starts blinking shortly thereafter.

  • WRT54GP2 not working - Power LED blinking fast.

    My WRT54gp2 has been working without issues for 2 years. All of a sudden from yesterday, the power LED is blinking fast. I am not able to connect to the web interface. My computer says limited or no connectivity. The internet and WAN LED are steadily lit. Has anyone faced this issue ? Is my router brick now ?

    As the power light on the router is blinking..It means that the firmware of router is corrupted..Check this link to unbrick the router.

  • WRVS4400N Diag/Power LEDs blinking

    Hey,
    Recently tried to update firmware on our WRVS4400N (v1) router (from WRVS4400N_V1.0_V1.1_Firmware.zip), and ended up with router alternatively blinking the red Diag and the Power LEDs...
    Googled the whole thing...and tried resetting the router (power off / on....reset button help for 60 secs +, etc)...pretty much everything most people were suggesting (including this page on the Cisco FAQ for the WRVS4400N: http://www.cisco.com/en/US/products/ps9923/products_qanda_item09186a0080a358b9.shtml - including trying with the LAN adapter speed set manually to 10Mpbs/Half-Duplex, w/Static IP address), and absolutely nothing.
    So, a couple of questions:
    1) Any other suggestions of what I could do...
    and assuming that answer to 1 is No - what are my options?  Router was bought nearly 3 years ago from a Reseller (NCIX, in Canada)...
    Trying to find the information on the warranty - getting different answer - although I did see 3 yrs somewhere...can I just call in and RMA it?
    Thx

    Good afternoon,
    The Small Business Routers typically come with three years of hardware support, including the ability to RMA if thorough troubleshooting proves the device to be faulty. However, if the tools we use determine that, based on your serial number, the product is no longer within that period, you may have to furnish a Proof of Purchase to verify entitlement.
    I would highly suggest going ahead and contacting us at 1-866-606-1866 (US and Canada) with the serial number and a Cisco.com user ID so we can create you a case and troublshoot your router if it falls within the warranty period.
    Thank you,
    -Lindsey

  • Neo4 does not POST (Power cuts + 3 second Power LED Blinking)

    Hi,
    This is my first build and I have already been plagued with 2 problems.  First, I finished the build and ran for one night and then the PSU went bad and needed to be replaced (replaced with same model).  Now, after running fine for about two weeks, the system shutdown over night and won't restart.  No activity should have been happening overnight.   When I try to start the system, the fans and everything start for about one second and then stop.  The power LED begins to blink every 3 seconds and no power is given to the system.  The D-bracket does not have any lights showing, they go out after the first second of running.  Here is what I have tried so far:
    1.  Tested power supply on second system and it worked fine.
    2.  Removed the motherboard from the case and set it on the static bag it came in.  Then with only the video (with it's power) and the two MB power cables connected, I tried to boot the system.  The same problem occured, power off after 1 second and LED blinks.
    3.  Bought a new PSU (Mad-Dog 500W which has +12V/30A) and still the same problem.
    4.  Removed each RAM module and tried with just one stick, still the same problem. 
    So I think I the only things left are MOBO and CPU...  I would think if it was the CPU, I would get a signal from the D-Bracket.  Any help? 
    Thanks in advance!

    Quote from: Deathstalker on 12-April-05, 00:14:59
    I would try removing the Power Cord from the Power Supply and the Battery from the mobo. Leave them out a good 15 to 20 minutes before putting them back.
    If that does not work, try a different brand of RAM for testing purposes.
    Deathstalker,
    Thanks for the suggestions.  I tried removing the battery and power for 15 minutes and replacing, but no luck, same problem.  This system was working for two weeks with the PQI RAM modules. Can this compatability change all of a sudden while running and just power down the system?

  • Why is the power light blinking?

    I've had some issues connecting to the internet.  I just replaced the cable modem and have it all set up.  I still don't have connectivity through the router.  I'm able to connet the computer directly to the modem and it works just fine.  But, I noticed that the router power light keeps blinking.  What might this be telling me?  Is the router trashed?

    Hello salin, the reason why you can't get online on your router because the router is not in good condition. The power light of your router should be solid at all times. There could be a problem with your router's firmware because the power is blinking. It can still be solve but you need to diagnose it first if you can still fix it because maybe it went bad already. To help you diagnose the router then try to follow the steps.
    > connect PC to Modem and download your router's firmware here.
    > disconnect PC from Modem and connect PC directly to the Router in port 1 (don't connect the Modem yet)
    > press and hold the reset button of the router firmly for 60sec while router is turn on and just release it after
    > unplug the power cord of the router and wait for another 60sec before plugging it back in
    > check the lights on the router to see if the power turn solid
       -if power light stops blinking then start updating your router's firmware and reconfigure your router
       -if power light is still blinking then continue the steps below
       > check if you can get an IP from the router.
          -if you can get an IP from the router (the default gateway should be 192.168.1.1) then start updating your router's firmware and reconfigure your router
          -if you can't get an IP then assign static ip to your PC. Use Static IP:192.168.1.10, Subnet Mask:255.255.255.0, Default Gateway:192.168.1.1 and just leave the Prefered and Alternate DNS empty.
          > ping the default gateway number. Click start and click RUN. In the RUN box, type CMD and click OK button. There's a black window that will open. Beside the blinking cursor, just type ping 192.168.1.1 and hit enter on the keyboard.
            -if you got this on the black window ping statistics- got 4 replies, 0% loss then start updating your router's firmware and reconfigure your router
            -if you got this on the black window ping statistics- got 4 replies, 100% loss or media state, media disconnected then that means your router is no longer responding and thus you need to replace it.
    How to update your router's firmware?
    > access the web page of the router and go to Administration tab and just below that click the Firmware Upgrade sub-tab.
    > browse for the firmware you saved in your PC and open it.
    > click the Upgrade button.
    > if Successful then just close the web page and reset the router for 20sec and just release it after. Turn off the router and wait for another 20sec before plugging it back in.
    > check the lights on the router. It should turn solid.
    How to reconfigure the router?
    -If you have Cable Internet Setup, click here
    -If you have DSL Internet Setup, click here
    "Nankurunaisa" "It will all work out just fine!"

  • Power led blinking

    I have a hp 5175ea, some days I can not turn on the computer by pressing the power button as it flashes without stopping.
    There is no sound, the fan is operating normally and the hard drive LED flashesnormally.
    The screen does not light up, and you can not press any button.
    What can be the problem? Highlight your reply soon thanks

    Hello @NoGameNoLife,
    I have read your post on how your notebook computer is not able to power on, and I would be happy to assist you in this matter!
    Since there is a blinking orange light where the AC adapter plugs into your computer, I recommend following this document on Computer does not start and the LEDs blink or the computer beeps, as well as Using and Testing the AC Power Adapter. This should help to restore the power to your notebook.
    If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • HP 6735s won't boot, power LED blinks 7 times

    The HP 6735s laptop stopped working.  Only sign of life, power LED flashes 7 times after on/off switch is pressed.  What's wrong, experts?

    Try a hard reset. Sometimes it works and is always the first step to take.
    remove the battery and the ac adapter plug from the laptop.
    press and hold the power button for fifteen seconds.
    install either the battery or ac adapter power and press the power button to attempt a boot into the OS.
    If that doesn't work then remove the hard disk to see if it gets past the splash screen and the BIOS whines that it can't find a bootable OS. That would indicate a hard disk failure.
     Also worth tying is removing the memory module(s) from the DIMM slots and then reinstalling them. That reseats the modules and cleans some oxidation off the module pins (if there is any)
    Another, perhaps a laptopsaver (in a manner of speaking) is the HP Pavilion dv2000/dv6000 and Compaq Presario  v3000/v6000 Series Notebook PCs - HP Limited Warranty... Check it and see if your laptop is covered.
    regards,
    erico 
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Hp 630 power led blinking 3 times

    Hello Brothers,
    My HP 630 notebook is not powering on by battery neither by power adapter connected. If I press power button when its connected the L.E.D besides the power plug blinks 3 times. This happens till the battery is charged; if the battery is not charged these L.E.Ds don't even light up.
    I expect the laptop to power on(when connected to wall outlet) even if the battery is out. Can someone kindly suggest what could be wrong here?
    Thanks a bunch in advance
    Regards
    Jag

    well, I have tried combo's of all 8 sticks in all different slots... sooo guessing mother board..
    not really worth repairing when I can get a mini for less than the cost to fix it... any one want to buy it for parts?

  • Smart camera 1764 Status & power led blinking

    I am using NI smart camera 1764. when i am giving 24 V DC supply to the camera then Power & Status LED is blinking at high rate in RED colour. on the other hand pass & fail LED also blinking in RED & GREEN colour alternatively. i am not able to connect camera to my computer through ETHERNET cable & cannot use for my application. 
    Please suggest me the solution as soon as possible.

    Hello,
    Have a look at this document on page 52 http://www.ni.com/pdf/manuals/372429b.pdf.
    It seems to be an application error.
    Try to boot your camera in safe mode with no app, using the switces.
    If you can connect, then try to reinstal using VBAI.
    Regards

  • Pap2t - power led blinking

    Hello,
    Suddenly my pap2t stoped.
    The red led is blinking, and the internet led is light on green.
    I have tried to restart it (with and without phone, internet link) - nothink happend.
    I can :
     ping it.
    I cann't :
     access through http
     hear the menu after ****
    I downloaded the new firmware, but i cant send it -> "no response from device"
    Do you have any sugestions ? Can I fix it ?

    If you are able to Ping PAP2, but unable to access the setup page of PAP2, Have you tried to disable the Firewall and Antivirus on your Router and then check if you are able to access the setup page pf PAP2. If still you are unable to login, then you need to reset pap2 and then try to login .

  • Wrt54g v6 power LED blinking

    I did everything in the faq including new firmware
    router still blinks every minute or so and disconnects all wired and wireless connections.

    Try this link and check if it make any difference..If not then,it's a time to change the router.

Maybe you are looking for