Wi fi works on one computer but is not being recognized by my phone and other computers?

My new airport wifi signa;l is picked up by my computer, but alerts there is 'no internet connection' on my laptop and phone and ipad.  Anyone else have this problem?  Were you able to fix it?
Thanks.
michael

Shortcut Method
On your Mac, please open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window that appears
Check the setting for Router Mode. It should be set to DHCP and NAT. If it's not, change to DHCP and NAT and click Update at the lower right of the window and allow a full minute for the AirPort Extreme to restart.
Then, power off both the modem and AirPort Extreme
Wait at least 15 minutes, longer will not hurt
After the power down period, power up the modem and let it run for 5 minutes
Then, power up the AirPort Extreme
Check the network. If all devices connect, you are good to go. If connection issues still exist, you will need to move to the.......
Start from scratch method
With the AirPort Extreme powered on for a few minutes, hold in the reset button on the back of the device for 10 seconds and release. Allow a full minute for the Extreme to restart to a slow, blinking light.
Repeat the steps above starting with the power down of the modem and AirPort Extreme.
The AirPort Extreme is automatically reset to DHCP and NAT when you perform the reset, so you do not need to check this setting.
This time, when you power up the AirPort Exteme again, you will need to reconfigure the Extreme again. You can use the same device name, wireless network name, etc that you used before if you wish, or change things up.

Similar Messages

  • HELP!! WRT54G2 works for one computer, but not for the other

    I have a WRT54G2 and it is connected to 2 computers. The internet works in one computer, but not on the other. The tech support said i needed to configure it or firmware or something like that. But my product is out of warranty and I really need the internet on the other computer as well. Please Help!!!

    As your one computer is working fine then there is no problem with the router so far...
    The computer which is not working...check the IP Address on that...
    Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
    IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
    If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
    If you get 4 replies then type ping 4.2.2.2 and press Enter, if you get request timed out, then you need to upgrade your router's firmware...If you get 4 replies then type ping yahoo.com and press Enter...If you get replies for Yahoo then you should get the Internet after adjusting the browser settings...
    Adjusting Browser Settings : Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
    If yahoo times out then provide static DNS on your LAN Connection...
    Click on the Start button >>> Settings >>> Control Panel >>>Network Connections- Right click on the icon for Local Area Connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the Following DNS Settings' Preferred DNS 4.2.2.2 Alternate DNS - 192.168.1.1>>Click on Ok button to Save and Click on "Close" on main Properties window...You should be able to go online...

  • I´ve installed Photoshop CC 2014 on one computer but when I should install the program on my other computer it ask for a serial number. Where could I find this?

    I´ve installed Photoshop CC 2014 on one computer but when I should install the program on my other computer it ask for a serial number. Where could I find this?

    Hi,
    No serial needed for subscriptions.Your applications can't communicate with the activation server.
    Check and delete Adobe entries on your hosts file as explained on step 3 :
    Sign in, activation, or connection errors | CS5.5 and later

  • Can you sync thunderbird email between several computers so if you delete an email on one computer in thunderbird it also deletes it out of the other computers.

    Can you sync thunderbird email between several computers so if you delete an email on one computer in thunderbird it also deletes it out of the other computers it syncs with? I have three computers I use daily in different location and have thunderbird on each computer. I find it time consuming to have to repeatedly delete the same emails from each location. I am thinking that by leaving the emails on the server and not downloading them in each computer would solve this. Is my assumption here correct? If not? How would you set up Tbird to sync?

    If you set up your email account(s) as IMAP instead of POP3, then each computer / smart phone can view the mail, but if any of them delete a message (or move it to another folder on the server), the same action will be seen on the other computers.
    See https://support.mozilla.org/en-US/kb/imap-synchronization

  • My external HD of 1TB is not being recognized by the iMac and when after a long waiting period it does, the whole computer becomes extremely slow. Do I need any particular add-on to make it workable?

    My external HD of 1TB is not being recognized by the iMac and when after a long waiting period it does, the whole computer becomes extremely slow. Do I need any particular add-on to make it workable?
    Before I updated to OS X Mavericks I was using another external disk that was getting disconnected ocasionally so I bought a new ADATA HD710 portable 1TB Drive and moved the files to it. This new drive which is supposed to be OS X Mavericks compatible takes minutes to show the files especially when opening second and third level folders which has made mu iMac unusable
    What should I do?

    Your Mac should be able to recognize many different types of drives (including Windows-formatted drives) immediately for Reading, provided they are in good working condition and not damaged. There should be no need to transfer to a different type of drive.
    If there is no recognition of this drive, see if it can be seen in Disk Utility.
    If your aim is to transfer the data on it DO NOT use ERASE or PARTITION as these will completely erase all the information on the Drive.
    If the drive is present while the Mac sleeps, it is likely to drop out and not be seen any longer, especially if it is a USB-powered drive.

  • CL_WD_RUNTIME_SERVICES= ATTACH_FILE_TO_RESPONSE( ) works in one system but does not in other

    Hi folks,
    We are facing an issue here with a custom web dynpro application that export an excel. The following piece of code has been written in this application to export an excel:
    cl_wd_runtime_services=>attach_file_to_response(
           EXPORTING
             i_filename      = c_filename
             i_content       = xtext
             i_mime_type     = c_mimetype
             i_in_new_window = abap_false
             i_inplace       = abap_false ).
    Now, the issue is this - it works fine in one system but does not in other system. HttpWatch shows ERROR_HTTP_INVALID_SERVER_RESPONSE in the system where it does not work. Any ideas?
    Regards,
    Shiromani

    Hi Shiromani,
    You mean "Other System" is other PC. If so, it seems that there is an issue with browser
    Please check the below SAP note
    1679126 - Server sends timeouts that cannot be reproduced
    Also, compare the browsers versions in both systems.
    Regards,
    Rama

  • My home share is not working i have tried everything it works on one computer but not the other help!

    I have tried uninstalling and reinstalling itunes i have tried messing with my avast and I cant get anything to work please help me! it works on another computer in the house but everytime i try to click on his library it says it loading his library and then stops and goes to my music. plz help!

    When normally powering the phone, there would not be a loading bar, you would just see the Apple logo. You can try a reset of the phone, hold the sleep/wake and home buttons together until you see the Apple logo and then release. The phone will reboot.
    You can take the phone to Apple, by making an appointment at the Genius Bar to have the hardware checked. Apple handles warranty and post-warranty issues, not Verizon. Have Apple look at the hardware to see if there are any problems.

  • Labview program works on one computer, but doesn't on another.

    We have a laptop running a custom data aquisition program that was made with labview by an external company. It communicates via ethernet with a box full of national instruments hardware that is connected to some sensors. While it works fine on the laptop, attempts to install the software on other computers results in the following error message "An error occured while attempting to open the configuration file "C:\program files\(name of the program)\data\(name of our company)fieldpoint.iak"". This error occurs whenever we try to open the test settings page or run a test. I've checked that directory and the file is in fact there.
    The new computers (we've tried several) always have difficulty connecting to the hardware via ethernet, and if you look at the network activity in windows you can see a whole bunch of packets being sent but only a few if any being recieved. I'm wondering if this is a network configuration problem? I've tried to match as many settings as I can find but to no avail. 
    The company that made the software isn't responding to emails.
    Any ideas would be greatly appreciated!
    Solved!
    Go to Solution.

    I suspect that the problem you have communicating with the equipment is a configuration issue. You mentioned you see lots of packets going out but nothing coming back. Are the packets going out being sent to the correct IP Address?
    I am not sure why you are not seeing the file since you say it is there. When you installed this application did you use their installer or simply copy things over to the other computer. There may be registry settings that are not there if you simply copied it. Also, there may be other support files that are not present on the other computer. You may also want to check the permissions on the files too. You will get an error if you try to open a file with the wrong permissions and this error is not always clear about what the issue is.
    Mark Yedinak
    "Does anyone know where the love of God goes when the waves turn the minutes to hours?"
    Wreck of the Edmund Fitzgerald - Gordon Lightfoot

  • Implicit read with assembly module instance working on one computer, but not another

    Hi,
    I'm trying to set up an on-site computer to run a VI which uses assembly instances for data communication, but for some reason I'm unable to establish a connection to the PLC.
    I'm running the example vi "CreateAssemblyInstance.vi" to try and get the communication set up before I start using my actual program.
    When I run this code on my development machine, I'm able to establish a connection to the PLC and read data. I then go into RSLogix 5000 and change the IP address to the on-site machine and try to run the test VI there, but I'm unable to make a connection. LabVIEW-side, the program thinks that it's established a connection and is reading/writing data, but PLC-side I'm getting a "Connection Failed" message in RSLogix.
    I find it weird that LabVIEW thinks the connection was established just fine, which the RSLogix says it can't connect to the VI.
    Just wondering if anyone else has had this happen. We aren't sure why the same VI runs on one machine but not another. We used RSLogix to change the IP address of the target machine, so we don't think that's the issue. And both computers are on the same network, so we don't think it's a firewall issue either.
    LabVIEW-side, things should be identical. I'm running the same example VI that came with the Ethernet/IP module. PLC-side, we're changing the target IP of the module within RSLogix 5000 (and we're sending the updated information to the PLC) to match the machine we're trying to make a connection with. Are we missing any steps? This is the first time we've tried using an assembly module, so we're having a hard time troubleshooting.
    Any ideas on why this is happening?

    I'm pretty sure we're using a generic ethernet module:
    I can communicate explicitly with the problem computer, it's able to use 'Tag Read' and 'Tag Write' to communicate with the PLC.
    We started having another problem just recently too. The Tag Read and Write commands are almost always timing out. I keep getting the error message -251723752:
    Detailed error info: Error -251723752 occurred at EthernetIP Tag Read REAL.vi;Details: The request response was not received in the requested timeout period    Possible reason(s):  Ethernet/IP Industrial Protocol: (Hex 0xF0FF0018) The request response was not received in the requested timeout period
    I can't figure out what's causing this all of a sudden, could these issues be related?

  • Keyboard works on one computer but not the other

    I have an aluminum wireless keyboard that came with my Mac Pro (Early 2008). Some time ago, it just stopped working. I tested the bluetooth mouse and a few other bluetooth peripherals to check that it wasn't the Mac Pro's bluetooth that was malfunctioning. I was convinced that the keyboard was broken, and was about to take it to the Apple Store to get it fixed when I thought that maybe I should test the keyboard on another computer. When I did that, it worked perfectly, but it still does not work with my Mac Pro. I've tried changing the batteries and removing the pairing from my Mac Pro. When I try to re-pair it, the Mac Pro is unable to discover it. Thank you in advance for your help.

    Well start with these articles and see if that gets you anywhere...
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    http://docs.info.apple.com/article.html?artnum=305136
    iTunes for Windows: iTunes 7 doesn't recognize iPod
    http://docs.info.apple.com/article.html?artnum=304434
    iPod missing in "My Computer" or in iTunes for Windows
    http://docs.info.apple.com/article.html?artnum=61711
    Also you might try forcing the iPod into disk mode first, then connecting it to your computer and see if that makes it show up in iTunes...
    Putting iPod into Disk Mode
    http://docs.info.apple.com/article.html?artnum=93651
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear
    http://support.apple.com/kb/TS1493
    Patrick

  • Ipod works on one computer but not the other?

    Can someone please help me? My ipod works on my laptop but not the desktop. When I plug the Ipod into the desktop it sometimes shows up in Itunes but says it's corrupt. Which it obviously isn't because it works fine on it's own when not plugged into a computer and it works fine when I plug it into the laptop. Also when I looked in my computer the Ipod would show up as drive j and it would flash on and off. Well, I tried plugging the Ipod into a different port and that worked as far as drive j stopped flashing on and off. I tried changing the drive name and it wouldn't let me because it always went back to drive j even after I changed it to drive z. Itunes is playing music and is up to date. I have Windows Vista Home Premium 64 bit. Please help.

    Well start with these articles and see if that gets you anywhere...
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    http://docs.info.apple.com/article.html?artnum=305136
    iTunes for Windows: iTunes 7 doesn't recognize iPod
    http://docs.info.apple.com/article.html?artnum=304434
    iPod missing in "My Computer" or in iTunes for Windows
    http://docs.info.apple.com/article.html?artnum=61711
    Also you might try forcing the iPod into disk mode first, then connecting it to your computer and see if that makes it show up in iTunes...
    Putting iPod into Disk Mode
    http://docs.info.apple.com/article.html?artnum=93651
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear
    http://support.apple.com/kb/TS1493
    Patrick

  • -computername works for one computer but not multiples

    Hello,
    I am new to powershell and I am trying to run a basic command:
    Limit-eventlog -logname Security -computername server1, server2 -maximumsize 6400KB
    My computer and the two servers are both running powershell 4.
    If I remove one of the computernames the command works fine...it doesn't matter which one, each one will work, they just won't work together.
    The error message has nothing to do with the servers though:
    "Limit-eventlog: the value supplied for MaximumSize parameter has to be in the range of 64 KB to 4GB with an increment of 64KB.  Please enter a proper value and then retry".
    It doesn't matter what value I try (64 KB, etc )it is always the same error with both servers.  Remove one server and the command runs fine.
    What is the proper syntax to use for multiple servers?
    thanks

    Hi,
    This is the forum to discuss questions and feedback for Microsoft Excel, I recommend you post the question to the powershell forum
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=winserverpowershell
    The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly can either share their knowledge or learn from your interaction with us. Thank you for your understanding.
    George Zhao
    TechNet Community Support
    It's recommended to download and install
    Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
    programs.

  • ICal Subscription Works On One Computer But Not The Other

    I subscribed to a web based iCal subscription. The subscription refreshes on my Mac Mini but not on my desktop, which is connected to my iPhone. The iPhone therefore doesn't get the subscription contents either. I've tried deleting and resubscribing but nothing works.

    Hey Valenz0711,
    That definitely sounds frustrating. There are a few different reasons it may not be working on the iMac (iTunes is not up-to-date, Firewall Settings). The following article may provide more information on a resolution:
    Troubleshooting Home Sharing
    http://support.apple.com/kb/TS2972
    Thanks,
    Matt M.

  • Smart mailboxes work on one computer but not another

    I have an Macbook Air I use for work and I have setup smart mailboxes which work fine. On my personal Macbook Pro the smart mailboxes show up that I created on my Air but nothing shows up (of course). When I create a smart mailbox on my Pro it doesn't work. I no longer have iCloud mail synching to my Air and that did not make a difference.
    How can I get smart mailboxes to work on my Pro?

    Could it be a permission problem?

  • If two people use one computer, but we have separte itunes accounts, Apple ID, and icloud will my apps I get be stored in their account too since we are using the same computer?

    If two people share the same computer, but have separate itunes account, Apple ID, and icloud and one of them downloads an app will it also go into the other persons account since y'all use the same computer

    If you  have separate user accounts on the computer, then your downloaded apps are stored in your iTunes Library. See the following for dealing with having multiple users on the same computer: How to use multiple iPhone, iPad, or iPod devices with one computer.
    Using More than One iDevice on the Same Computer
    This applies mainly to couples who are adding another device and do not want their email, messages, etc. being duplicated on both devices. To begin read: How to use multiple iPhone, iPad, or iPod devices with one computer. You need to establish a separate Apple ID and password for whomever will use the new iDevice. See Apple - My Apple ID and Frequently asked questions about Apple ID. The easiest way is to do this on the computer using iTunes: iTunes- How to set up an Apple ID within iTunes.
    On the computer create a new user account for the person with the new iDevice. This will be the user account that person will always use. He/She will no longer use the other user account. This way that person will have a separate iTunes Library
    Start by transferring the new device(s) to a new account along with all your data.  Save any photo stream photos that you want to keep to your camera roll (unless they are already in the camera roll) by opening your Photos app, tap on Albums icon at the bottom. Now, tap on My Photo Stream album; tap Select; tap on the photos you want to select;, tap the share icon (box with upward facing arrow) in the lower left corner; then tap Save to Camera Roll.
    If you are syncing notes with iCloud that you want to keep then you need to open each of your notes and email them to yourself. Later you can copy and paste the text into new notes created in your new account.
    Tap on Settings > iCloud > Delete Account (only deletes it from this device, not from iCloud; the person keeping the current account will not be affected,) provide the password to turn off Find My Phone and choose Keep on My iDevice when prompted.  Sign in with a different Apple ID to create your new account. Choose Merge to upload your data.
    Once you are on separate accounts, you can each go to icloud.com and delete the other person's data from your account.
    Note: The essence of the above was created by user, randers4. I
    have made substantial changes to improve readability and syntax.

Maybe you are looking for