Win 7 Wireless connection problem to a Officejet Pro 8600 N911a

I have a Win7 64 bit pc that was connected wirelessly to my officejet pro 8600. Recently I lost connection to the printer with the Win7. I can print from my smartphone but not the Win7 PC. I uninstalled all the printer software Then I downloaded and reinstalled the drivers and tried to connect wirelessly it found the printer but it won't install the driver software. It found the IP address but had :3216/ at the end of the IP address? I can print when I connect using a USB setup. A message also stated that the PC and printer are not on the same router. However they are signed in to the same router name and password.

Hello there! Welcome to the forums @Tombi
I read your post about how your Officejet 8600 is not communicating over your network to your Windows 7 computer. I'd suggest checking the guide below and following the steps. If the printer happens to be on another network, these steps will sort it all out and you should be connected by the end!
'Unable to Find Printer' Error Message Displays on the Computer During a Wireless Network Installati...
Good luck to you! Let me know the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

Can;t enable web service on HP Officejet Pro 8600 N911a

HP Officejet Pro 8600 N911a we have installed this printer as a network printer. Everything works fine except that I cannot enable the Web service to EPrint or scan to an email. It says the printer cannot access the internet.
This question was solved.
View Solution.

Hello. First power cycle the printer, and the router to see if that will clear up the error message. To do that unplug the router then power down the printer using the power button. Then plug the router back in and once it is back up an running, turn on the printer and try to reconnect to web services
Then, if still unable to connect, I would set a static DNS on the printer. To set a static DNS you must access the embedded web server (EWS). You do that by entering the IP address for the printer into the address bar of the browser of your choice.
Once it brings up your Officejet's EWS, locate the tab that is labeled “Network”. From there look in the left column on the new page that will pop up and select IPv4, wired or wireless will depend on how the printer is connected to the network. That will bring up the page to set the Static DNS. It will be the 2nd portion of that page.
Set the radial dial to manual. Then, for the Manual preferred/Primary DNS, set it to 8.8.8.8 and the Manual Alternative/Secondary to 8.8.4.4; then click apply.
NOTE: if another message with an option to click “OK” appears, read that message carefully. Most of the time it is an option to undo the change you just did and you will want to avoid clicking that message. Just navigate away from that page by clicking on another tab.
Power cycle the printer. Once printer is back up and through with calibrations from being turned off and on. Reattempt to connect to web services by touching the icon.
I am a former employee of HP...
How do I give Kudos?| How do I mark a post as Solved?

Officejet Pro 8600 N911a not able to air print since Maverick update

My Officejet Pro 8600 N911a worked fine printing wireless before the newest Maverick upgrade. Now it will only print one print job after I turn the printer off and then back on. If I connect the computer to the printer, it seems to work fine, so it has to do with the upgrade and airprint. I have just downloaded the current Mavericks plug in, but there is no change.

When you say Airprint, are you printing Wireless diect to the 8600 or is the 8600 connected to your wireless network?
When you say the latest plu-n, do you mean the update from Apple Software Update (Apple Store) or the full 10.9 solution from HP.com?
In either case I would recommend first just deleting the print queue on the Macintosh and re-adding it. If that does not resolve the issue try resetting teh print system and adding the printer back new.
Try performing a "reset print system" on teh Macintosh and then reconnecting to the printer.
To reset the print system perform the following:
1. Open System Preferences
2. Click on the Print & Scan
3. click or click in the box listing the current print queues.
4. Select Reset printing system...
5. Enter admin User Name and Password
6. Reboot the Macintosh
7. Try setting up the printer again
I work for HP

I have officejet pro 8600 n911a ana cant turn it off

its new not used so much.. suddenly this problem has emerged.. i press on the turn off button.. and its like im not doing any thing.. it denies to turnoff!!

Hello bia7assan,
Welcome to the HP Support Forums! I see when you try and turn off your HP Officejet Pro 8600 n911a it will not power off, when you press and hold the power button.
I would like you to start here: The HP Printer Won't Turn On or Respond When the Power Button is Pressed, please note *If you are using a surge protector, extension cable, or power strip, follow these steps to plug the printer directly into a wall outlet to make sure that the power source functions correctly.
Let me know the outcome, I will watch for your reply.
Thanks in advance,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Can I print from my iPhone 4 using an HP Officejet Pro 8600 N911a

Can I print from my iPhone 4 using an HP Officejet Pro 8600 N911a. And if so how do I do this????

Hi stacy7560,
You can print from your iPhone4 to your 8600 using Apple's AirPrint feature. I have a few steps you can follow to do this:
1. Make sure the iPhone is on the same wireless network as your printer.
2. Select the mail application on the iOS device and open an email you wish to print.
3. At the top of the screen, locate and press the action icon.
4. Select the "Print" option.
5. Make sure your printer is in the top field of the Printer Options screen. If not, tap “Select Printer.” Your printer should appear.
6. Press the “Print” selection.
Note: To print a photo, follow these same steps once you have opened the image you wish to print.
Let me know if this helps.
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Webscan problem with HP Officejet Pro 8600 printer and OS Mavericks

I have an iMac with OS 10.9 Mavericks installed and an HP Officejet Pro 8600 Plus N911g printer. I recently downloaded the "HP-Inkjet-SW-OSX-Mavericks_v12.34.37" software update from the HP website but, since installing it, the image preview feature on Webscan now only shows a black screen and I cannot download the scanned image. I have uninstalled the update and reinstalled the old software - "Officejet-Pro-8600_v12.23.0" but the problem persists.
I am not sure if this is an HP problem or a Mavericks bug. Any advice/help would be greatly appreciated

The servicing when the printer is turned on is normal and is required to keep the printheads healthy (not clogged). See here for information.
As for power savings, the printer will automatically go into a low power mode when not printing for some time. It is not necessary to turn the product off and on to save power.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Officejet Pro 8600 n911a - not working, again

I purchased this printer (Officejet Pro 8600) last week. Set up was really difficult. A PC laptop set up quickly and works fine. My iMac and Mac Book - coulnd't 'see' the printer for set up. I managed to install drivers and achieve printing by using a USB cable to set up the wireless' connections using the IP address.
All worked for Wednesday to Friday. This monring, both Macs find the printer 'unreachable', the PC is printing fine.
I have:
Hard reset the printer
Downloaded the Apple support files, and restarted
Downloaded the most up to date drivers from the HP website
Still nothing. What next?
My Mac is using OS 10.8.5
This is costing me time and money, not withstanding the purchase price. What next ... I need a printer - or I wouldn't have paid for one.
All help gratefully received.

Good news - I've managed to add a static IP address.
So, for now at least, the iMac and Mac Book can see the printer and print. Hopefully it lasts ...
Still cannot 'scan to computer'. It works on the pc, but I cannot scan to/via the macs - which is what I need to do. And no, I cannot share a network folder on the pc (it is not mine). Is there any way around this? It used to work fine with the HP scan software on my old Deskjet F4580 ... any advice appreciated

HP Officejet Pro 8600 N911a - Print when Fax is Not Saved

Can I make it so a fax is printed when it's not saved? I know I can set it to print and save every time, but I rely on HP Digital Fax to save paper. If a fax is not saved, either due to a network error or if the computer that it usually saves to is shut off, can the fax just be printed?

, it's nice to meet you. I think I found something that may help with your faxing dilemma. This information was in the User Guide for the Officejet Pro 8600 e-All-in-One Printer - N911a; pg 69. Set up backup fax Depending on your preference and security requirements, you can set up the printer to store all the faxes it receives, only the faxes it receives while the printer is in an error condition, or none of the faxes it receives. The following backup fax modes are available:On > The default setting. When Backup fax is On, the printer stores all received faxes in memory. This enables you to reprint up to eight of the most recently printed faxes if they are still saved in memory. NOTE: When printer memory is low, it overwrites the oldest, printed faxes as it receives new faxes. If the memory becomes full of unprinted faxes, the printer stops answering incoming fax calls. NOTE: If you receive a fax that is too large, such as a very detailed color photo, it might not be stored in memory due to memory limitations.
On Error Only > Causes the printer to store faxes in memory only if an error condition exists that prevents the printer from printing the faxes (for example, if the printer runs out of paper). The printer continues to store incoming faxes as long as there is memory available. (If the memory becomes full, the printer stops answering incoming fax calls.) When the error condition is resolved, the faxes stored in memory print automatically, and then they are deleted from memory.
Off > Faxes are never stored in memory. For example, you might want to turn off Backup fax for security purposes. If an error condition occurs that prevents the printer from printing (for example, the printer runs out of paper), the printer stops answering incoming fax calls. NOTE: If backup fax is enabled and you turn the printer off, all faxes stored in memory are deleted, including any unprinted faxes that you might have received while the printer was in an error condition. You must contact the senders to ask them to resend any unprinted faxes. For a list of the faxes you have received, print the Fax Log. The Fax Log is not deleted when the printer is turned off. To set backup fax from the printer control panel 1. Touch (right arrow), and then select Setup.2. Touch Fax Setup, and then select Advanced Fax Setup.3. Touch Backup Fax Reception.4. Touch On, On Error Only, or Off. Reprint received faxes from memoryIf you set the Backup fax mode to On, the received faxes are stored in memory, whether the printer has an error condition or not. NOTE: After the memory becomes full, the oldest, printed faxes are overwritten as new faxes are received. If all the stored faxes are unprinted, the printer does not receive any fax calls until you print or delete the faxes from memory. You might also want to delete the faxes in memory for security or privacy purposes. Depending on the sizes of the faxes in memory, you can reprint up to eight of the most recently printed faxes, if they are still in memory. For example, you might need to reprint your faxes if you lost the copy of your last printout. To reprint faxes in memory from the printer control panel 1. Make sure you have paper loaded in the main tray.2. Touch (right arrow), and then select Setup.3. Touch Tools or Fax Tools, and then select Reprint Faxes in Memory. The faxes are printed in the reverse order from which they were received with the most recently received fax printed first, and so on.4. If you want to stop reprinting the faxes in memory, touch the Cancel button. Please let me know if these steps resolved your issue, or if there is anything else I can do to help. I look forward to hearing from you! Thanks,

Wireless Quit Working on HP Officejet Pro 8600 - N911g

Cannot re-establish wireless connection. When I go to the screen that lists the id's for the various wireless routers, the screen goes blank except for a code about 8 characters or longer that starts (I believe) with B849. The code is visible for less than a second. The sceen bkanks out that message and displays the instruction to stop and then start the printer while lights that border the display beging to blink.

Hey REFLaherty,
It sounds like the printer is having an issue with connecting to the internal wireless card. I would advise performing a factory reset on this printer, then trying to connect to the network again. I have the steps to perform this type of reset and will send this information to you in a private message here on the forums. Please check your inbox messages.
Before performing these steps, please read Bob_Headrick's thread on printer resets found here.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Problem getting my Officejet Pro 8600 Premium web service connected

I have been trying to get the web services set up on my printer and it keeps saying "Web services (ePrint and Apps) are being set up on the computer or the embedded web server (EWS). Please wait for the setup to complete."
I have been waiting for hours. The web server (which I just checked) says it cannot turn on the web services because another user is doing that. I presume that is the printer controll panel. I have tried restoring factory default settings. I have tried disconnecting the power cord and waiting 10 minutes. Nothing enables me to get past this error. What's going on?

rsfrid
After turning your printer and router off and power then back on, make sure you are still connected to your network and that the router has internet access. You might also check and make sure that HP ePrintcenter is not in a degraded state.
I am an HP Employee

My computer won't connect to my HP Officejet Pro 8600 Plus

When I tried to print stuff from my computer ( HP Pavilion Streamline) my computer said that it is not connected to my printer! What do I do?

Hello VinTheMonster,
I understand your OfficeJet 8600 Plus is saying it is not connected to your computer. Can you please let me know the following:
1. Your current Operating System.
2. Has it been successfully connected before?
3. How did you install? Using the software cd or the download from www.hp.com?
4. How are connected, USB or wireless?
5. Have there been any recent changes in your setup? or network (if wireless)?
I will watch for your reply, so we can begin troubleshooting.
Thanks in advance,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Copy problem with HP Officejet Pro 8600-always copys on both sides of paper

When I want to make a copy of a document, i.e., insert the document on the glass surface under the printer cover, I touch the copy function on the printer and the printer always makes a copy of the document on both sides of the paper. I do not know how to change the printer setting(s) in order to have a one sided copy feature.

Hi,
From the printer front panel click on Copy.
Click the Two Sided button and select "1 sided original - 1 sided copy".
Next click the Settings button, select Set as New Defaults and confirm, now 1 sided copy will default for any copy job.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Hp officejet pro 8600 n911a series

The Printer will not print out, stay's in queue, everything is connected, no jam's , set up for wireless, test was ok, says printer not connected, also turned off and on printer, doesn't work, can you help

Hi there, are you trying to print to the printer from a mobile device via HP's ePrint service?
Bet.
If my reply helped you, feel free to click on the Kudos button (hover over the "thumbs up").
If my reply solved your problem please click on the Accepted Solution button so other Forum users may benefit from viewing the post.
I am an HP employee.

Officejet Pro 8600 N911a and windows 8.1

I have been using the above mentioned printer for some time, but I'm now experiencing a problem in my set-up.
I get an error message saying "Cannot communicate with the printer" on my windows 8.1 stationary PC, and when I start troubleshooting with the HPprint and scandoctor the problem lies with the printqueue connection to the printer.
The error message asks me to update the IP-adress on the printer startpage, but I fail to identify the place to do so. Is it on the printer or somewhere inside the windows controlpanel?
Reinstalling the printer and restarting the windows machine helps (sometimes more than sometimes).
The printer connects wireless to my homenetwork through a TDC SAgem router and my W8.1 PC is connected to the same router via cable.
I have not met the problem when I print from my Ipad or Iphone both of course wireless.
How do I update the IP-adress or better how do I solve the actual problem??
Thank you in advance.
Erik Olsen

Hi eov,
Thank you for your response!
Please try the following solutions:
Use the printer troubleshooter from Microsoft. Fix printer problems.
Uninstall the software. Uninstalling the Printer Software.
Restart the print spooler. Restarting the Print Spooler in Windows 8 (Video).
Re-install the software using the HP Printer Install Wizard for Windows.
Hope this information helps you, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Officejet Pro 8600 N911a will not scan to computer

I have run the print and scan doctor with no luck After 12 months of no trouble at all my printer will no longer scan to my computer. The computer shows as available on the printer screen but I keep getting an eror. Scan cancelled

On the same Wireless Network Test Results report, may I know what the Signal Quality shows?
Click on the KUDOS button on the left to say "Thanks"
Please mark the post that solves your problem as "Accepted Solution"
I am an HP employee but the views here are my own.

Win 7 Wireless connection problem to a Officejet Pro 8600 N911a

Similar Messages

Maybe you are looking for