Windows (XP) not receiving IP address from LAN port on Airport Extreme

I have a DSL modem connected to the AEBS WAN port. Three computers (one Windows laptop, one emac, and one powerbook) can successfully connect to the internet wirelessly through the AEBS. The remaining desktop PC, running Windows XP, normally connects to the LAN port on the AEBS and there are no problems.
Suddenly, the desktop (always configured to get ip addresses automatically using DHCP) is not getting an IP address from the AEBS. I've confirmed this via IPconfig, and the address is 169..... The Windows error message is "limited or no connectivity."
When the desktop is connected directly to the DSL modem, however, it works just fine. Of course this isn't a satisfactory fix, as it means the DSL modem is no longer connected to the AEBS WAN port, and none of the wireless computers have internet access.
I've determined that the problem is not in the LAN port itself, as my powerbook successfully connects via ethernet through the AEBS LAN port.
I've also updated the AEBS firmware to 5.7.
Any suggestions on how to fix this. As I mentioned, the problem occurred overnight.

Try using System Restore to set the computer back to a time when it was working.
iFelix

Similar Messages

  • Are LAN ports on Airport Extreme active when used to extend WiFi network?

    I am thinking of buying an Airport Extreme to wirelessly extend the dual-band WiFi network from my Time Capsule. In this scenario, with the Extreme configured as a bridge, would I be able to use the LAN ports on the Extreme to join some AV kit to the network?
    Thanks ... Simon

    In this scenario, with the Extreme configured as a bridge, would I be able to use the LAN ports on the Extreme to join some AV kit to the network?
    Yes

  • How to disable LAN ports on Airport Extreme.

    Trying to disable my LAN ports and still leave the wireless access alone?

    There is no provision for this in AirPort Utility. You can disable wireless, but not ethernet.
    Message was edited by: Bob Timmons

  • Clients not receiving dchp addresses from server

    Our dhcp server (windows 2012) is failing to issues addresses to the pc's. Once the lease has expired on the pc (user goes on holiday for a week) the machine will fail to pick up an ip address on the users return.
    The event viewer on the server reads "IP address range of scope is 95 percent full with only 7 IP address available"
    I have gone through the dhcp scope of which there are 94 exclusions and i have a further 39 machines which require addresses. 
    On a class C subnet i should have far more than 7 addresses available.
    Any thoughts as to what might be at fault here.  
    This topic first appeared in the Spiceworks Community

    Just completed a major network upgrade... So decided it was time to stack some ofmy old switches! Can anyone date some of these things?And some before and after shots: The first one is of a distribution cabinet (2 x 10Gig Fiber link ag. to server room) on the other side of our site, the last two are of the core cabinet in my server room. Will take some more pictures later.

  • Not receiving some texts from a ported google voice #

    my google voice # was ported over to my droid x2 phone and i am recieving calls just fine but i am not getting any type of text messages from friends. where are they going and how do i get them to come over to me?

    Do you mean that your ported your Verizon Wireless number to Google Voice? If so, it may take a few days for the port to complete and text routing to happen correctly.  If you still aren't getting messages after a few days, you'll want to contact Google and Verizon to make sure the port happened properly.  The messages MAY be showing up in your online Google account, and you could view them there, but it's not likely until the routing is corrected.
    Or just that you directed your Google Voice number to ring on your Droid X2?  If so, you need to set up an application on your phone to recieve the messages.  Do you have the Google Voice app on your phone?  You should be able to read the messages in your online Google Voice account, and find instructions there to set it up on your phone.

  • I am trying to redeem my itune prepaid card and the system request the security question's answer which i have forgot. im trying to retrieve it through my yahoo email address which i set earlier but i do not receive any email from apple support.

    i am trying to redeem my itune prepaid card and the system request the security question's answer which i have forgot. im trying to retrieve it through my yahoo email address which i set earlier but i do not receive any email from apple support. Can i know what should i do to retrieve my security question's answer?

    http://support.apple.com/kb/HT5312
    -If you established a rescue email address, there will be a link on the "Passwords & Security" page of id.apple.com.  Clicking the link will send the reset to your rescue email address (NOTE:  This is not the same address as your Apple ID email)
    -If there is no link on the page, then you didn't establish a rescue email address.  Contact AppleCare at 800.694.7466 (If you are in the US), and ask for account security.  You will need to answer some questions to verify your identity, AND you will need access to a computer to generate a temporary support pin.
    -If you are not in the US, click http://support.apple.com/kb/HT5699 - Apple ID: Contacting Apple for help with Apple ID account security
    HTH

  • APs unable to receive IP address from DHCP (core 6500 series switch)

    Dear Friends,
    a week ago I had stable wireless network APs were getting IPS from 6500 series switch (DHCP) but unfortunately some WISM got rebooted and now APs are unable to receive IP address from Core 6500 DHCP, to cater this issue  I have another DHCP server configured on windows 2008  i created another subnet and and put APs in that vlan now all APs are are successfully receiving IPS from windows DHCP server I don't know why APs are not able to receive IPs from core 6500 series DHCP.
    please advice
    Thanks
    Faysal

    Thanks george for stepping up here is DHCP config
    ip dhcp excluded-address 10.10.30.1 10.10.30.20
    ip dhcp excluded-address 10.10.8.1 10.10.8.10
    ip dhcp excluded-address 192.168.10.1 192.168.10.5
    ip dhcp excluded-address 10.9.20.1 10.9.20.30
    ip dhcp pool vlan_30
    network 10.10.30.0 255.255.254.0
    default-router 10.10.30.1
    option 60 ascii """"""""""""""""""""""""CiscoAPc1250""""""""""""""""""""""""
    option 43 hex f110.0a0a.1e0b.0a0a.1e0d.0a0a.1e0f.0a0a.1e11
    dns-server 10.10.2.11
    lease infinite
    ip dhcp pool WiSM1_SP
    network 192.168.10.0 255.255.255.248
    default-router 192.168.10.1

  • Iphone mail app not receiving e-mail from 1 sender

    The Mail app on my iPhone 6/iOS 8.3 is not receiving e-mail from one sender sent to my Outlook e-mail account. This sender's e-mail address is "[email protected]". It is a notification of digital magazines available from Zinio. I know the mail app is not receiving the e-mail because Outlook 2013 on my desktop and Outlook.com do receive these e-mails. How can I get the mail app on my iPhone to receive these e-mails from this address?

    Initially it sounds like something with your backup data caused the issue with your new device but if you restored your device again without using the backup and the issue still exists it wouldn't appear to be the issue at all. Since the problem seems to only be with one person are you sure it's not an issue on their end and with their network that is stopping you from receiving the messages? Have you tried *228 option 2 to see if that helps?

  • Client not receive ip address - dhcp_reqd

    Hi,
    In my environment there's a  5508 (firmware 7.4.110.0) and ap 1600 with a ias radius server. All wlan are in flex-connect local switching, one client try to connect on a wlan but not receive ip address. After enabled debug aaa all i took the log corresponding :
    Cisco Controller) >*emWeb: Feb 11 16:52:36.047: Created WARP Capabilities IE (length 12) for WLAN LAB
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Adding mobile on LWAPP AP 00:3a:9a:77:55:a0(0)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Association received from mobile on BSSID 00:3a:9a:77:55:06
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP radio
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Max Client Trap Threshold: 50  cur: 3
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Re-applying interface policy for client
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 In processSsidIE:4264 setting Central switched to FALSE
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific Local Bridging override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Local Bridging Interface Policy for station 18:3d:a2:25:01:a4 - vlan 0, interface id 0, interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Re-applying interface policy for client
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Processing WPA IE type 221, length 24 for mobile 18:3d:a2:25:01:a4
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 unsetting PmkIdValidatedByAp
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfMsAssoStateInc
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Idle to Associated
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2:session timeout forstation 18:3d:a2:25:01:a4 - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Sending Assoc Response to station on BSSID 00:3a:9a:77:55:a0 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfProcessAssocReq (apf_80211.c:7399) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Associated to Associated
    *apfMsConnTask_2: Feb 11 16:54:22.506: 18:3d:a2:25:01:a4 Updating AID for REAP AP Client 00:3a:9a:77:55:a0 - AID ===> 4
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 1)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Received EAPOL START from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 2)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAP Response packet with mismatching id (currentid=2, eapid=1) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received Identity Response (count=2) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 EAP State update from Connecting to Authenticating for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticating state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=3) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 3)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 3, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=4) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 4)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 4, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=7) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 WARNING: updated EAP-Identifier 4 ===> 7 for STA 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 7, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Processing Access-Accept for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created for mobile, length = 253
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created in mscb for mobile, length = 253
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Creating a PKC PMKID Cache entry for station 18:3d:a2:25:01:a4 (RSN 0)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Sending EAP-Success to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Starting key exchange to mobile 18:3d:a2:25:01:a4, data packets will be dropped
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Entering Backend Auth Success state (id=7) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Received Auth Success while in Authenticating state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticated state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-key in PTK_START state (message 2) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 apfMs1xStateInc
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5952, Adding TMP rule
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IP
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 0, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Key exchange done, data packets from mobile 18:3d:a2:25:01:a4 should be forwarded shortly
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
    *pemReceiveTask: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask3: Feb 11 16:54:22.707: 18:3d:a2:25:01:a4 Sent EAPOL-Key M5 for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.769: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5576, Adding TMP rule
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
      IPv4 ACL ID = 255,
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 0, Local Bridging intf id = 0
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *pemReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    (Cisco Controller) >*emWeb: Feb 11 16:54:46.127: 18:3d:a2:25:01:a4 Central Switch = FALSE
    *emWeb: Feb 11 16:54:46.128: 18:3d:a2:25:01:a4 Central Switch = FALSE
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >*emWeb: Feb 11 16:55:36.461: 18:3d:a2:25:01:a4 Central Switch = FALSE
    *emWeb: Feb 11 16:55:36.463: 18:3d:a2:25:01:a4 Central Switch = FALSE
    From log i know that 802.1x passed, while dhcp don't send ip address. It seems that the local vlan id is 0 while in reality is 3... WHY ? i don't understand.
    Someone can help me to find the problem? i think the problem is on the network, the dhcp ( the corporate router) is directly connected to the ap.

    Are you setting your FlexConnect native vlan and the wlan to vlan mapping?  You also need to make sure you have the ip helpers setup and that dhcp is working.  I would configure a switch port to a vlan that the wireless users is suppose to be on locally at that site and connect a laptop to that port and make sure that the laptop gets an address.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • Not receiving information sent from specific server

    I'm not receiving data sent from a specifc address. Other (non Verizon) users are able to get data from the address. I can send data to it and pinkg and tracert times are good. The vendor needs a check of verion servers to see if there's a specific problem related t otransmitting data from the address. Online Verizon help was of no use since they cant' understand that a ping is only for seeing if you can connect to the servere.
    The specific proble is addressed in the following from the data provider's internet support
     Layer 4(transport layer) traffic is not reaching you from our app server with the address https://os-bo-app04-04.boldchat.com/. They want to know if there's any Verizon issue related to this.

    That's a curious question response from a company. Verizon and any isp are only providing layer 1,2 & 3 of the osi model. Any would verizon be involved in layer 4 issues for a particular website? I would think that answer would be pretty obvious.

  • One Yahoo! mail account does not receive email sent from .mac

    OK, this is an odd problem, and any help would be appreciated.
    My girlfriend's Yahoo! mail account does not receive email sent from my .mac address. If I send email from my Gmail or Yahoo! accounts she receives the message. No one else has informed me that they haven't received email from the .mac address. Additionally, the .mac account is in her address book.
    Anyway, has anyone seen a similar pattern with Yahoo! or any other email provider?
    Thanks.
    - Jennings

    Thanks for the reply . . . and yes, the recipient's email provider likely holds the answer.
    However, I was hoping someone here might have had a similar experience and could answer as the email provider is Yahoo, and they are slow in responding to help requests . . . for a period I hosted a personal, paid website through Yahoo Domains and help tickets lingered for several days on multiple occasions (this being the reason the site is no longer hosted by Yahoo). I also doubt Yahoo will expend too much energy resolving a problem for a free email account.
    Anyway, I posted in the Yahoo mail forums, and hopefully something will come-up . . . .

  • I upgraded from Iphone4 to Galaxy S4 and not receiving text messages from Iphones.

    I upgraded from Iphone4 to Galaxy S4 and not receiving text messages from Iphones.I went to https://supportprofile.apple.com/MySupportProfile.do and unregistered my old iPhone to resolve the issue. It's been one day and I cannot recieve text messages from Iphones

    Verizon wiping out old phones would have nothing to do with it. The phone is no longer associated with the number, so wiping the phone would have no effect. It is your Apple ID which is the problem. You have iMessage turned on for your Apple ID. iPhones which have your Apple ID associated with your contact will send texts to your Apple ID, not your phone #. If you have another Apple device which can use iMessage, you could turn off iMessage in that device, but as long as your friends have your Apple ID associated with your contact and you have turned on iMessage in an Apple device and never turned it off before switching from an Apple device to another platform, you will have this problem.
    You can bet that Apple will not address the problem, as they don't see it as a problem if someone is using a phone other than an iPhone. Apple expects no one will ever switch away from an iPhone once one has been used. Therefore, no problem for them to address.
    The problem lies with Apple wanting their users to go through yet another proprietary interface, iMessage, which the MAJORITY of all smartphone users do not have access.

  • HELP ... Not receiving email messages from particular Yahoo Group

    Ever since the evening of 3/26 every member of my Yahoo Group with an email address from Comcast.net has not been able to reliably receive messages from the group. Out of over 40 emails since then, we've received 4 (2 on 4/1 and 2 this morning). There are no error messages involved, there are just no emails in our inboxes. Yahoo does not indicate that any of the messages have "bounced". The messages are not in my spam folder (in fact, the first Comcast "helper" i worked with had me turn off the spam filter in Comcast,net) Oddly, I (and the others) can receive messages from other Yahoo Groups that we are members of, just not ours: SoundOfNewEngland I was on the phone with Comcast for 2.5 HOURS on 4/3 and was basically told that since I could receive a test message from Comcast that the error must be with Yahoo!   After contacting Yahoo, I was told that since others in the group can receive the messages, that the error must be with Comcast. <sigh> The last email I got from Yahoo said that Comcast would need to add Yahoo info into the Comcast whitelist. I told this to a Comcast technician during a help chat on 4/5 ... and she told me to fill out this form: http://www.comcastsupport.com/sdcxuser/asp/comcast_blockedprovider.asp I did that even tho the issue is that the Yahoo Group's messages were being blocked and I didn't have an IP address for those, but I could provide the domain name:  yahoogroups.com I tried to put the info that Yahoo Groups gave me for the whitelist, but the description is limited to 1024 characters  Needless to say, I have not received a resonse from Comcast within 24 hours of posting the form  Here is the info from Yahoo!: "Since you have already reviewed your settings, and confirmed that the emails are not landing in your spam folder, you will need to follow up with your email provider again, since it appears that they are dropping emails from the group. Email providers generally do this because they think a message is spam, and they are particularly likely to use this approach with bulk messages coming from an email list.
    If you have not done so already, you can provide them with the following link:
    http://tech.groups.yahoo.com/group/ygmailadmin/
    There, they can find a current list of all of our outgoing email servers for white listing.
    They can also contact the owner of this official Yahoo! Group, for further assistance in troubleshooting this issue, by sending an email to:
    [email protected]    However, if your email provider continues to fail to deliver your Yahoo! Group messages, we strongly suggest you consider changing your email provider to another provider who will. This doesn't necessarily mean you need to change your ISP. You can also use a free Web-based email service like Yahoo! Mail or Hotmail while retaining your current ISP." If it helps, the Yahoo incident # is: 120402-011733 It's not a big group, only 86 members. All together we generate maybe 100 messages a month ... not even close to being considered spam.  Most of the members are older and not comfortable with new technology. Asking them to create new emails is not an option.  This group is our primary means of communicating with each other, so the sooner we get this resolved, the less stress for my members! I'm sorry for the length of this message, i'm just trying to provide all the detail i can.  I hope you can help. Thanks,Carol 

    more info: I usually get my mail using Outlook, but the messages are not there when I view them directly on Comcast.net either ....  I'm using Chrome for a browser and have VISTA for my OS Here's a message header from the most recent email sent to the group that I did not receive (i will xxx out the email addresses) at my Comcast address but DID receive at my Yahoo address:
     From Eileen Fri Apr 6 11:56:17 2012
    X-Apparently-To: [email protected] via 72.30.239.82; Fri, 06 Apr 2012 11:56:22 -0700
    Return-Path: <sentto-512785-10246-1333738581-sxxxxxxx1=yahoo.com@returns.groups.yahoo.com>
    Received-SPF: none (domain of returns.groups.yahoo.com does not designate permitted sender hosts)
    bzpwPjwvc3Bhbj48L2ZvbnQ.CgogPC9vOnA.PC9zcGFuPjwvZm9udD4KCiAg
    SWYgd2UgaGF2ZW50IHNlZW4geW91IGluIHlvdXIgdHdvIHBpZWNlCmJsdWUg
    b3V0Zml0LCB5b3VyIGJsdWUgY2hva2VyIGFuZCBlYXJyaW5ncyBhbmQgeW91
    ciBzaWx2ZXIgc2hvZXMsIHBsZWFzZSBjb21lCnNlZSB1cyBuZXh0IFR1ZXNk
    YXkuICBPdXIgc2hvdyBpcyBmYXN0IGFwcHJvYWNoaW5nIGFuZAEwAQEBAQ--
    X-YMailISG: e3e1T3cWLDu.Osw7OOZubcQqoSFUnmYIENQDkbvkbj.f1YSG
    jeAsGCF.2eVO0JR1Ont3IrpMUmJCMBHXwJV6tuJpHB5.LPn7VwqkcfADDoed
    JOpt.3LNoYA23EaFa_OUJb0doF5L55CZJKrWyKutYx3q1ycssiBzIPYq1YRq
    M6NG_VY0ImWBg704ufqziQ.3Y1dS6xtLcUrzsWfqrlj_a8X752hy7fRfHOOI
    OL03MhCTHdMXCd81eu4z36yWv5gYdqwWLvmSjxmXWez67MS5YnOOLiQE2vvJ
    kZqaHBfyJgJvY5boLHYBm5dzwq1b5ymrD.XjqipzCyn.Ly3e_9XMgLO1.d0n
    Zq3qDhV49SvAEuOO4RxU0DXCdJw5gdQfC0qFyPvguMpUd_6Assu__D2Sb7v_
    .Dk1RzStQW2dWjZKZyrAJi8ixfshB9l6JyfbGTI8TjohFgWkbylHw.qPQ7eT
    CB4.S7zJ81hwssFjfk1A2PS4qZo_dlP6j1VkohVKlVx07Q2hOk2BEAl4FdN.
    ltjgDcrFVVz4Ue9Uznv2lzPNjXDqna.BA9cJtVWWRMLUhDN9pLG7CYHmgm_l
    G_4.FHji7x8NuZLgOZKW__lQsWoLLBfZQCEgbsAUyghT7RA9L31QPL2BZcMF
    4nJkstskat7oY244L9yxqA_n.3z_qZjaK9zjqUClMD8FI7QcYvfTq3eXDNPb
    odKsaHP8iUUMrnDaKMh6RE9RmtQx399fT59iDM2djhFiwZMON5570vs4vKTx
    nkJkR_ls_6j85AFGBHxsNd5nBOI0o241qOczrttmahzI08LSCcIH17eaZImm
    9FYLJK606YV9wnY7xA9QAiMfhs7VYi4JSiby6zfpEL9cZwC3XCPW2.8nwiZR
    0BvvZ47rDEzGPJR.kawsSssoqK9xg1ar8zd4O46i_VXvQSMkrlm5PWtAEIGp
    fcVzHsllXBltFn2hqGHPPIKTBqUcQ7jkNbchUQnuYQ3ecbyfd0QnFBl7ufL2
    PrzOKX09XggZs0OUt8iQQtmgE3Zjn8FGw.cyh3eoCNcRoFf9QaPyKTRegA.e
    miJ3O3jckBWROX_kE0Smh9VcVAFLRkZu93BSNDpWsnwp3VqaPxmAVOpsrEPf
    uBEqtMr9RwxD.n8JmAzItxKht0GzNI5Bwf1eK3gerM7bZRxk3lppAmMBWv06
    IrfCL9_EJnFGcGy_lYsz77DGDktIBXCqb_IAx4dVAoTySc700TnINLEQxkVH
    Y32iGH8-
    X-Originating-IP: [98.139.165.5]
    Authentication-Results: mta1260.mail.ac4.yahoo.com from=yahoogroups.com; domainkeys=pass (ok); from=yahoogroups.com; dkim=pass (ok)
    Received: from 127.0.0.1 (HELO ng2-ip9.bullet.mail.bf1.yahoo.com) (98.139.165.5)
    by mta1260.mail.ac4.yahoo.com with SMTP; Fri, 06 Apr 2012 11:56:22 -0700
    DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoogroups.com; s=lima; t=1333738582; bh=sG8gHMXUATS8FPacoEmQj76vBTuNbmLCXaXWAAi6isw=; h=Received:Received:X-Yahoo-Newman-Id:X-Sender:X-Apparently-To:X-Received:X-Received:X-Received:X-IronPort-AV:X-Received:X-Received:To:Cc:Thread-Topic:Thread-Index:Message-ID:Accept-Language:Content-Language:X-MS-Has-Attach:X-MS-TNEF-Correlator:acceptlanguage:X-Originating-IP:X-eGroups-Msg-Info:From:Sender:MIME-Version:Mailing-List: Delivered-To:List-Id: Precedence:List-Unsubscribe: Date:Subject:X-Yahoo-Newman-Property:Content-Type; b=Rm1y/6pBXsTuRSaDcXiCTVvq2gag2bxCn33QtzJ758CZ+3HKtQKe+XN6lTdZpP+/vDm8tdDSIdtzb9KhdtvVWcJXijUMLCdwNCBpJGVkKxX14dHjh2y/SRJ+4lHzbXvh
    DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=lima; d=yahoogroups.com;
    b=LDjKTTQnA7I/VM4aeY0zRYwkr8NkUMk8LYaBXfnp3GE2q15fsiVZ5fdkeGROAluMK5ybf06af+JzduWb03vJAnmi71j5m0l5bFNZjgBsy0u55hLT6nXABUubEMgRR51M;
    Received: from [98.139.164.120] by ng2.bullet.mail.bf1.yahoo.com with NNFMP; 06 Apr 2012 18:56:22 -0000
    Received: from [98.137.34.40] by tg1.bullet.mail.bf1.yahoo.com with NNFMP; 06 Apr 2012 18:56:22 -0000
    X-Yahoo-Newman-Id: 512785-m10246
    X-Sender: [email protected]
    X-Apparently-To: [email protected]
    X-Received: (qmail 48751 invoked from network); 6 Apr 2012 18:56:20 -0000
    X-Received: from unknown (98.137.34.45)
    by m4.grp.sp2.yahoo.com with QMQP; 6 Apr 2012 18:56:20 -0000
    X-Received: from unknown (HELO mail02.bmchp.org) (216.57.136.41)
    by mta2.grp.sp2.yahoo.com with SMTP; 6 Apr 2012 18:56:20 -0000
    X-IronPort-AV: E=Sophos;i="4.75,382,1330923600"; 
    d="scan'208,217";a="146119"
    X-Received: from excahtp1.bmchp.org (HELO EXCAHTP1.healthnet.org) ([172.16.100.21])
    by mail02.bmchp.org with ESMTP; 06 Apr 2012 14:56:19 -0400
    X-Received: from EXMBCL1.healthnet.org ([169.254.1.124]) by
    EXCAHTP1.healthnet.org ([::1]) with mapi; Fri, 6 Apr 2012 14:56:19 -0400
    To: "'[email protected]'" <[email protected]>
    Cc: "'[email protected]'" <[email protected]>
    Thread-Topic: fittings
    Thread-Index: Ac0UJvLIs9IpwqtfSy+hSVXx3b26bQ==
    Message-ID: <[email protected]>
    Accept-Language: en-US
    Content-Language: en-US
    X-MS-Has-Attach: 
    X-MS-TNEF-Correlator: 
    acceptlanguage: en-US
    X-Originating-IP: 216.57.136.41
    X-eGroups-Msg-Info: 1:12:0:0:0
    From: Eileen <[email protected]>
    Sender: [email protected]
    MIME-Version: 1.0
    Mailing-List: list [email protected]; contact [email protected]
    Delivered-To: mailing list [email protected]
    List-Id: <Soundxxxxxxxx.yahoogroups.com>
    Precedence: bulk
    List-Unsubscribe: <mailto:[email protected]>
    Date: Fri, 6 Apr 2012 14:56:17 -0400
    Subject: [SONE] fittings
    X-Yahoo-Newman-Property: groups-email-tradh-m
    Content-Type: multipart/alternative;
    boundary="_000_69C23C04D36F874092DCF98593C8DA539D4824864BEXMBCL1health_"
    Content-Length: 7828  Thank you for any guidance you can provide

  • Flexconnect Local Switching Hosts Do Not Receive IP Addresses

    Hello,
    My WLC software version is 7.4.110.0. I have a branch office in my lab. The AP in my branch is configured as flexconnect with native VLAN of 700. The SSID that I have in the branch office is configured to do local switching. The show wlan is added below.
    My tunneled SSID still working and I can still receive IP addresses from it. My issue is last week I have the Flexconnect working with no problem, then this morning I can connect to the SSID, but I'm not receiving IP addresses for my test wireless clients.
    Thanks
    [code]
    WLAN Identifier.................................. 2
    Profile Name..................................... ACS Guest
    Network Name (SSID).............................. RMTGuest
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      Client Profiling Status ....................... Disabled
       DHCP ......................................... Disabled
       HTTP ......................................... Disabled
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 0
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ 300 seconds
    --More-- or (q)uit
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... RK2WLC5508-01
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... 172.28.27.130
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    PMIPv6 Mobility Type............................. none
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream          Downstream
    Average Data Rate................................   0                      0
    Average Realtime Data Rate.......................   0                      0
    Burst Data Rate..................................   0                      0
    Burst Realtime Data Rate.........................   0                      0
    Per-Client Rate Limits........................... Upstream          Downstream
    Average Data Rate................................   0                      0
    Average Realtime Data Rate.......................   0                      0
    --More-- or (q)uit
    Burst Data Rate..................................   0                      0
    Burst Realtime Data Rate.........................   0                      0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Disabled
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    --More-- or (q)uit
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Disabled
             PSK..................................... Enabled
             CCKM.................................... Disabled
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
    --More-- or (q)uit
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
    AVC Visibilty.................................... Disabled
    --More-- or (q)uit
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
    Mobility Anchor List
    WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    [/code]

    is the VLAN still mapped on the AP, and allowed across the trunk?
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • LG Revolution not receiving text messages from iphone user

    I am not receiving text messages from iphone user, sporatically.  The messages are showing as reveived on Verizon website in usage detail, but not being received on my phone.

        This issue needs fixed asap! I have a few suggestions that should help you get this resolved. If they are showing up in the usage details, that means they are hitting the Verizon network, but for some reason they are not showing up on the phone.   I recommend clearing the cache from your messaging/text messaging programs. Go to settings> applications> manage apps> all> Messaging/Text Messaging> Force Stop/Clear Cache/Clear Data. Erase the old text threads that you have saved and retry.
    If that doesn't work, please let us know the following:
    1) Do they come in delayed or not at all?
    2) Do you have any 3rd party messaging apps installed?
    3) Do they have any problems receiving messages from you?
    4) When they're sending messages, are they directly to you, or do you have this problem when the iPhone user sends to a group of people?
    Thanks for the additional info! I'm sure we can find a fix.
    Regards,
    MikeS_VZW
    Follow us on Twitter @VZWSupport

Maybe you are looking for

  • Is there an alternative to dragging a library to copy it?

    hi, As a follow up to my previous post Can temporary library be deleted after importing it? I am happy to report that the un-needed library was ditched unceremoniously and that the actual library was copied from the ailing drive to a new drive via dr

  • How to call import/export

    Hi.. How to call the export/import statement through form? There's one button that will execute the export or import process. How to write the command? Thank in advance

  • My mic is unavailable in Vi

    Hi there. I can't get my mic to work under Vista. When going to recording devices it says unavailable and I can't find where to make it available. Anyone knows a solution for this?I have the latest X-Fi sound drivers installed on my system. My soundc

  • Cheque management - Reuse printed cheque number

    Hi Experts, Client has posted the payment document through F-58, the cheque has gone to the vendor, Now client wants to cancel that cheque & payment document & reuse the cheque no. & assigned the same cheque no. to the new payment document as there w

  • Conditional Format in Cross-Tabs

    Hello, i have a problem with conditional formatting in cross-tabs(Word-Template-Builder) My Cross-Tab looks like: +++++++++++++++++++ColumnHeader1 +++++++++++++++++++ColumnHeader2 +++++++++++++++++++ColumnHeader3 RowHeader 1 | Row Header 2 | Data Fir